Voltammetric study on the complex of thiram-copper(II) and its application

Based on the formation of tetramethylthiuram disulfide (thiram)-copper(II) complex by square-wave voltammetry on a glassy carbon electrode, a new method is proposed for determination of thiram. There is a good linear relationship between peak current and concentration of thiram in the range of  mol l⁻¹ (r=0.999). The method is applied to the determination of thiram residue in plant with satisfactory results, compared with results achieved by using HPLC. Two oxidation peaks and two reduction peaks are obtained by cyclic voltammetry on a glassy carbon electrode in 0.2 mol l⁻¹ HAc-NaAc (pH 4.0) solution containing thiram-copper(II) complex. The electrode reaction process is quasi-reversible with adsorptive characteristics. The mechanism of electrode reaction is discussed.     

Electrodeposition of gold nanoparticles on indium/tin oxide electrode for fabrication of a disposable hydrogen peroxide biosensor

A novel disposable third-generation hydrogen peroxide (H₂O₂) biosensor based on horseradish peroxidase (HRP) immobilized on the gold nanoparticles (AuNPs) electrodeposited indium tin oxide (ITO) electrode is investigated. The AuNPs deposited on ITO electrode were characterized by UV-vis, SEM, and electrochemical methods. The AuNPs attached on the ITO electrode surface with quasi-spherical shape and the average size of diameters was about 25 nm with a quite symmetric distribution. The direct electron chemistry of HRP was realized, and the biosensor exhibited excellent performances for the reduction of H₂O₂. The amperometric response to H₂O₂ shows a linear relation in the range from 8.0 μmol L⁻¹ to 3.0 mmol L⁻¹ and a detection limit of 2 μmol L⁻¹ (S/N = 3). The value of HRP immobilized on the electrode surface was found to be 0.4 mmol L⁻¹. The biosensor indicates excellent reproducibility, high selectivity and long-term stability.     

Determination of arsenic in gold samples using matrix exchange differential pulse stripping voltammetry

A method comprising matrix exchange differential pulse stripping voltammetry (DPSV) at a gold film electrode has been proposed for the determination of small quantities of arsenic in pure gold. A wall-jet cell (WJC) and an on-line deoxygenation system were used to facilitate matrix exchange. The gold(I) cyanide complex was formed to avoid gold deposition on the electrode together with the arsenic. The pH of the sample solutions were adjusted to 3, as alkaline solutions gold(I) cyanide produced interference and the uncomplexed cyanide led to passivation of the gold film electrode. Matrix exchange electrolytes consisting of 4 mol l⁻¹ hydrochloric acid or a combination of 2 mol l⁻¹ sulphuric acid and 0.2 mol l⁻¹ hydrochloric acid could be utilised. Arsenic concentrations as low as 0.1 mg l⁻¹, could readily be detected in a gold matrix with a 60 s deposition time. While, cobalt and silver did not interfere with the arsenic determination, copper interfered even when present at similar concentrations to that of arsenic.     

Development of an enzymeless biosensor for the determination of phenolic compounds

The construction of amperometric enzymeless biosensors for phenolic compounds determination, using carbon paste electrode modified with copper phtalocyanine (CuPc) and histidine (His), based on the chemistry of the dopamine β-monooxygenase (DβM) enzyme that catalyzes the hydroxylation of the dopamine and its analogs is shown. The modified carbon paste was evaluated on electrodes constructed in two ways: putting the paste into a cavity of a rotating disk electrode and a platinum slide electrode fixed into a glass tube. The sensor in hydrodynamic conditions presented a linear response range between 30 and 250 μmol l⁻¹, with a sensitivity of 4.6±0.1 nA l μmol⁻¹ cm⁻² for catechol, response time of 3 s and lifetime of about 50 days when stored at room temperature. The sensor in static conditions showed a linear response range from 40 to 250 μmol l⁻¹, with a sensitivity of 0.30±0.01 nA l μmol⁻¹ cm⁻² for catechol. The sensors presented the following relative response order for dopamine and some analog species: catechol>dopamine>guaiacol>serotonin>phenol.     

Direct electrochemistry and electrocatalysis of cytochrome c immobilized on gold nanoparticles-chitosan-carbon nanotubes-modified electrode

A robust and effective nanohybrid film based on gold nanoparticles (GNPs)/chitosan (Chit)/multi-walled carbon nanotubes (MWNTs) was prepared by a layer-by-layer self-assembly technique. Cytochrome c (Cyt c) was successfully immobilized on the nanohybrid film modified glassy carbon (GC) electrode by cyclic voltammetry. The direct electron transfer between Cyt c and the modified electrode was investigated in detail. Cyt c shows a couple of quasi-reversible and well-defined cyclic voltammetry peaks with a formal potential (E^0′) of −0.16 V (versus Ag/AgCl) in pH 7.0 phosphate buffer solution (PBS). The Cyt c/GNPs/Chit/MWNTs modified GC electrode gives an improved electrocatalytic activity towards the reduction of hydrogen peroxide (H₂O₂). The sensitivity is 92.21 μA mM⁻¹ cm⁻² and the calculated apparent Michaelis-Menten constant () is 0.791 mM, indicating a high-catalytic activity of Cyt c. The catalysis currents increase linearly to the H₂O₂ concentration in a wide range of 1.5 × 10⁻⁶ to 5.1 × 10⁻⁴ M with a correlation coefficient 0.999. The detection limit is 9.0 × 10⁻⁷ M (at the ratio of signal to noise, S/N = 3). Moreover, the modified electrode displays rapid response (5 s) to H₂O₂, and possesses good stability and reproducibility.     

Investigation of the luminescent properties of terbium-anthranilate complexes and application to the determination of anthranilic acid derivatives in aqueous solutions

The luminescent properties of terbium complexes with furosemide (FR), flufenamic (FF) acid, tolfenamic (TF) acid and mefenamic (MF) acid have been investigated in aqueous solutions. For all four compounds, complexation occurs when the carboxylic acid of the aminobenzoic group is dissociated and is greatly favoured in the presence of trioctylphosphine oxide as co-ligand and Triton X-100 as surfactant. Under optimum conditions, luminescence of the lanthanide ion is efficiently sensitised and the lifetime of the resonance level of terbium in the complex is ranging between 1 and 1.9 ms, against 0.4 ms for the aqua ion. The sensitivity of the method for the determination of anthranilic acid derivatives is improved by one to two orders of magnitude with respect to that achieved using native fluorescence or terbium-sensitised luminescence in methanol. The limits of detection are 2×10⁻¹⁰, 5×10⁻¹⁰ and 2×10⁻⁹ mol l⁻¹ for flufenamic acid, furosemide and tolfenamic acid, and mefenamic acid, respectively, with within-run RSD values of less than 1%. The method has been applied to the determination of flufenamic acid in spiked calf sera with and without sample pretreatment. Depending on the method and the analyte concentration, the recovery was ranging between 83 and 113% and the lowest concentration attainable in serum samples was close to 1×10⁻⁷ mol l⁻¹.     

Preparation of silver hexacyanoferrate nanoparticles and its application for the simultaneous determination of ascorbic acid, dopamine and uric acid

A silver hexacyanoferrate nanoparticles/carbon nanotubes modified glassy carbon electrode was fabricated and then successfully used for the simultaneous determination of ascorbic acid, dopamine and uric acid by cyclic voltammetry. A detailed investigation by transmission electron microscopy (TEM) and electrochemistry was performed in order to elucidate the preparation process and properties of the nanocomposites. The size of silver hexacyanoferrate nanoparticles was examined by TEM around 27 nm. Linear calibration plots were obtained over the range of 4.0 × 10⁻⁶-7.8 × 10⁻⁵, 2.4 × 10⁻⁶-1.3 × 10⁻⁴ and 2.0 × 10⁻⁶-1.5 × 10⁻⁴ mol L⁻¹ with detection limits of 4.2 × 10⁻⁷,1.4 × 10⁻⁷ and 6.0 × 10⁻⁸ mol L⁻¹ for ascorbic acid, dopamine and uric acid, respectively. The practical analytical utilities of the modified electrode were demonstrated by the determination of ascorbic acid, dopamine and uric acid in urine and human blood serum samples.     

Selective response of dopamine in the presence of ascorbic acid on carbon paste electrode modified with titanium phosphated silica gel

Titanium phosphate grafted on the surface of silica gel (devoted briefly as Si-TiPH) was synthesized and used as bulk modifier to fabricate a renewable three-dimensional chemically modified electrode. The Si-TiPH bulk modified carbon paste electrode was used for the selective determination of dopamine (DA) in the presence of ascorbic acid (AA). The modified electrode offers an excellent and stable response for the determination of DA in the presence of AA. The differential pulse voltammetry peak current was found to be linear with the DA concentration in the range 2 × 10⁻⁷ to 1 × 10⁻⁶ and 2 × 10⁻⁶ to 6 × 10⁻⁵ mol L⁻¹. The detection limit of the proposed method in the presence of 2.0 × 10⁻⁵ M of AA was found to be 4.3 × 10⁻⁸ mol L⁻¹ for DA determination. The proposed method was successfully applied for the determination of DA in injections.     

Chiral salen Mn(III) complex-based enantioselective potentiometric sensor for l-mandelic acid

A new enantioselective potentiometric sensor containing chiral salen Mn(III) as the chiral selector was designed for the assay of l-mandelic acid (l-MA). Optimized membrane electrodes displayed linear dynamic range from 1 × 10⁻⁵ to 1 × 10⁻¹ mol L⁻¹ with a detection limit of 7.2 × 10⁻⁶ mol L⁻¹ and a Nernstian response of −58.1 ± 0.5 mV decade⁻¹ towards l-MA within pH range 7.0-10.2. The potentiometric enantioselectivity coefficient () of this sensor was −4.0, indicating that the chiral salen Mn(III) complex-based electrode exhibited fairly good discrimination toward l-MA over counter isomer d-MA. The mechanism of chiral recognition for l-MA is discussed by using HF/STO-3G calculation method simulation.     

Electrochemical behavior of dopamine at a 3,3′-dithiodipropionic acid self-assembled monolayers

Monolayers of 3,3′-dithiodipropionic acid (DTDPA) were prepared on a polycrystalline gold electrode through a self-assembly procedure to produce a gold 3,3′-dithiodipropionic acid self-assembled monolayer (AuDTDPA) modified electrode. The characterization of the AuDTDPA electrode was investigated by cyclic voltammetry and ac impedance using the [Fe(CN)₆]^3−/4− redox couple. The electrochemical behavior of DA on the modified electrode AuDTDPA was studied by cyclic and square-wave voltammetries, using phosphate buffer as supporting electrolyte. The oxidation peak current for DA increases linearly with concentration in the range of 0.35 × 10⁻⁵ to 3.4 × 10⁻⁵ mol L⁻¹. The performance of the AuDTDPA modified electrode was evaluated for the electroanalytical determination of dopamine (DA) in a pharmaceutical formulation. The AuDTDPA modified electrode showed a stable behavior and the presence of surface-COOH groups avoided the passivation of the electrode surface during the dopamine oxidation.     

Validation of an environmental friendly segmented flow method for the determination of phenol index in waters as alternative to the conventional one

Phenolic compounds are a sort of common pollutants in water. Phenol index becomes an expedite indicator for the evaluation of the contamination level of water samples, in spite of the knowledge of the individual phenol and its derivatives are also important.In this work, an environmental friendly method for the determination of phenols, using a segmented flow system based on the conventional method's reactions without the liquid-liquid extraction step, was validated.Three linear dynamic ranges using C₆H₅OH: 1-10 μg l⁻¹, 10-200 μg l⁻¹ and 0.2-2.5 mg l⁻¹, with a coefficient of variation lower than 2%, were obtained. Several method's performance parameters were determined: limits of detection, limits of quantification, precision through duplicate analysis and trueness using the reference materials purchased from LGC Promochem, RTC no. QCI-043-2 Lot:P1. Measurement uncertainty was evaluated using an interlaboratory approach based on proficiency testing data. Relative combined uncertainty for phenols in water samples, , of 0.054 were obtained, in according to those imposed by the Portuguese Legislation: target for 1 μg l⁻¹ of phenol (surface waters) and target for 500 μg l⁻¹ of phenol (wastewaters).A high efficiency reduction and elimination of reagents and wastes, reduction of analysis time and exposition of the analyst were also obtained.     

Glucose biosensors prepared by electropolymerization of p-chlorophenylamine with and without Nafion

Two different glucose biosensors for the amperometric determination of glucose, based on poly(p-chlorophenylamide) (PCPA) and bilayer film of PCPA and Nafion (PCPA/Nafion), are successfully developed. These two biosensors show linear amperometric responses to glucose ranging from 2.0×10⁻⁴ to 3.5×10⁻² mol l⁻¹ and 5.0×10⁻⁴ to 7.5×10⁻² mol l⁻¹, respectively, with the same correlation coefficient of 0.9988. Effects of polymerization potential and polymerization time on the performance of enzyme sensors are studied. It is found that PCPA, as a non-conducting polymer, can largely reduce the influence of electroactive interferents. Introduction of inner Nafion membrane not only further eliminates the influence of ascorbic acid on the sensor response but also increases electrode stability.     

Electrochemical determination of maltol in beverages with glassy carbon electrode and its silica sol-gel modified electrode

The electrochemical behavior of maltol on a glassy carbon (GC) electrode was investigated. The results were applied to differential pulse voltammetric determination of maltol in beverages pretreated by ultrafiltration. Under the optimum experimental conditions, the linear range is 1×10⁻⁵ to 6×10⁻⁴ mol l⁻¹ maltol and the relative standard deviation for 0.4 mmol l⁻¹ maltol is 0.6% (n=9). The detection limit was 5 μmol l⁻¹. Furthermore, silica sol-gel film on GC electrode could be used as suitable selective membrane, which integrated selective membrane on the electrode and substituted for the pretreatment of ultrafiltration. Under the above conditions, maltol was determined by semi-differential linear sweep voltammetry at a silica sol-gel modified GC electrode in the concentration range of 5×10⁻⁶ to 5×10⁻⁴ mol l⁻¹. The detection limit was 2 μmol l⁻¹ and the relative standard deviation for 0.1 mmol l⁻¹ maltol was 0.7% (n=7). The proposed method is of sensitivity, simplicity, rapidness and no contamination. It had been applied to the direct determination of maltol in beverages such as grape wines, drinks and beers without any pretreatment. The results obtained with the present method were satisfactory with those obtained by spectrophotometry. It could be used as a simple and practical method for the determination of the flavor enhancer maltol in beverages.     

On-line preconcentration of palladium on alumina microcolumns and determination in urban waters by inductively coupled plasma mass spectrometry

A method for on-line preconcentration of palladium at ultra-trace level on alumina microcolumns and determination by inductively coupled plasma mass spectrometry (ICP-MS) has been developed. A sampling time of 10 min (30 ml) and an eluent (KCN) volume of 300 μl provides a limit of detection of 1 ng l⁻¹. The precision was 4% at the 25 ng l⁻¹ level. The proposed system allows the on-line removal of the primary interferents (Cu and Y) providing the credible accuracy of the results. The proposed method is suitable for palladium determination in urban water samples. Platinum concentration in the analysed urban water samples was also determined.     

Dioxouranium(VI)-carboxylate complexes: A calorimetric and potentiometric investigation of interaction with oxalate at infinite dilution and in NaCl aqueous solution at I = 1.0 mol L and T = 25 °C

In this paper we investigated the interactions between dioxouranium(VI) and oxalate using (H⁺-glass electrode) potentiometry and titration calorimetry. Potentiometric measurements were carried out in NaCl aqueous solutions and at T = 25 °C in a wide range of experimental conditions (concentrations, ligand/metal molar ratio, pH, titrants) at low ionic strength values (I ≤ 0.090 mol L⁻¹, without supporting electrolyte) and at I = 1.0 mol L⁻¹; different procedures were employed for the acquisition of experimental data and careful analysis of these data performed. In all cases the speciation model that best fits experimental data takes into account the formation of the binary mononuclear species UO₂(ox)⁰, UO₂(ox)₂²⁻, UO₂(ox)₃⁴⁻ widely reported in literature, the ternary hydroxyl mononuclear species UO₂(ox)OH⁻, UO₂(ox)(OH)₂²⁻, UO₂(ox)₂OH³⁻, UO₂(ox)₃OH⁵⁻, the protonated ternary mononuclear species UO₂(ox)₃H³⁻ and the binuclear species (UO₂)₂(ox)₅⁶⁻.Calorimetric measurements were carried out following similar procedures and in the same experimental conditions as employed for the potentiometric measurements at I = 1.0 mol L⁻¹ in NaCl. The stability of UO₂²⁺-oxalate²⁻ complexes is fairly high and their main contribution to stability is entropic in nature. Some linear empirical relationships were found which make it possible to calculate (i) the contribution of a single bond: and ; (ii) chelate stabilisation per ring: and and (iii) the mean stability of negatively charged Na⁺-ion pair complexes: log^TK = (0.46 ± 0.02)·|z| (z = charge of complex species), ΔG° = −(2.60 ± 0.1)·|z| kJ mol⁻¹ and TΔS° = 2.5 ± 0.5 kJ mol⁻¹. Both potentiometric and calorimetric results provide evidence of the penta-coordination of the species UO₂(ox)₃⁴⁻. SIT parameters were calculated from the data at I = 0 and I = 1.02 mol kg⁻¹. Comparisons are made with literature data. An insoluble dioxouranium(VI) ternary complex was synthesised (at I = 1.0 mol L⁻¹ in NaCl) and characterised by thermoanalysis and elemental analysis.     

Determination of sulfur-containing amino acids by capillary electrophoresis dynamic reaction cell inductively coupled plasma mass spectrometry

Capillary electrophoresis dynamic reaction cell™ inductively coupled plasma mass spectrometry (CE-DRC-ICP-MS) for the determination of sulfur-containing amino acids is described. The sulfur-containing amino acids studied include l-cysteine, l-cystine, dl-homocystine and l-methionine. The species studied were well separated using a 70 cm length×75 μm i.d. fused silica capillary while the applied voltage was set at +22 kV and a 10 mmol l⁻¹ disodium tetraborate buffer (pH 9.8) containing 0.1 mmol l⁻¹ EDTA and 0.5 mmol l⁻¹ Triton X-100 was used as the electrophoretic buffer. The sulfur-selective electropherogram was determined at m/z 48 as by using its reaction with O₂ in the reaction cell. The method avoided the effect of polyatomic isobaric interferences at m/z 32 caused by and on by detecting as the oxide ion at m/z 48, which is less interfered. The detection limit of various species studied was in the range of 0.047-0.058 μg S ml⁻¹, which corresponded to the absolute detection limit of 1.3-1.6 pg S based on the injection volume of 27 nl. We determined the concentrations of selected sulfur-containing amino acids in urine and nutritive complement samples. The recovery was in the range of 92-128% for various species.     

Voltammetry determination of trace manganese with pretreatment glassy carbon electrode by linear sweep voltammetry

This paper described the determination of trace manganese using linear sweep voltammetry at a pretreatment glassy carbon electrode. The glassy carbon electrode pretreated by electrochemical method in the 0.1 mol l⁻¹ NaOH solution greatly improved the electrode responsibility in the determination of manganese(II). The barrier to the detection of low manganese concentration was overcome by means of autocatalytic effect of manganese oxide deposited on the electrode in advance. Under the optimum experiments condition (0.04 mol l⁻¹ NH₃-NH₄Cl buffer solution, pH 9.0), the linear range was 4×10⁻⁸ to 1×l0⁻⁶ mol l⁻¹ Mn(II) for linear sweep voltammetry and 1×10⁻⁹ to 4×10⁻⁸ mol l⁻¹ Mn(II) for convolution voltammetry. The relative standard deviation for 2×10⁻⁸ mol l⁻¹ Mn(II) is 3.4%. The proposed method is simple, rapid, sensitive and selective. It had been applied to the determination of trace manganese in samples with satisfactory results.     

Direct electrochemistry and electrocatalysis of hemoglobin immobilized in a magnetic nanoparticles-chitosan film

Magnetic nanoparticles (Fe₃O₄) were synthesized by a chemical coprecipitation method. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to confirm the crystallite structure and the particle's radius. The Fe₃O₄ nanoparticles and chitosan (CS) were mixed to form a matrix in which haemoglobin (Hb) can be immobilized for the fabrication of H₂O₂ biosensor. The Fe₃O₄-CS-Hb film exhibited a pair of well-defined and quasi-reversible cyclic voltammetric peaks due to the redox of Hb-heme Fe (III)/Fe (II) in a pH 7.0 phosphate buffer. The formal potential of Hb-heme Fe(III)/Fe(II) couple varied linearly with the increase of pH in the range of 4.0-10.0 with a slope of 46.5 mV pH⁻¹, indicating that electron transfer was accompanied with single proton transportation in the electrochemical reaction. The surface coverage of Hb immobilized on Fe₃O₄-CS film glassy carbon electrode was about 1.13 × 10⁻¹⁰ mol cm⁻². The heterogeneous electron transfer rate constant (k_s) was 1.04 s⁻¹, indicating great facilitation of the electron transfer between Hb and magnetic nanoparticles-chitosan modified electrode. The modified electrode showed excellent electrocatalytic activity toward oxygen and hydrogen peroxide reduction. The apparent Michaelis-Menten constant for H₂O₂ was estimated to be 38.1 μmol L⁻¹.     

Determination of arsenic, iron and selenium in moss samples using hexapole collision cell, inductively coupled plasma-mass spectrometry

Different collision gases (H₂, He and premixed 7% H₂ in He) used in the hexapole collision cell of an inductively coupled plasma-mass spectrometer (ICP-MS) were compared, and the gas-flow rates were optimized for the determination of arsenic (), iron () and selenium (). The study showed that the argon-based interferences at mass-to-charge ratios (m/z) of 56, 75 and 80 can be overcome by the optimized gas flows (7.5 ml min⁻¹ premixed 7% H₂ in He and 2 ml min⁻¹ H₂) in the hexapole collision cell. Detection limits of 15.5 ng l⁻¹ for iron () and 29 ng l⁻¹ for selenium () in 2% (v/v) HNO₃ were obtained under optimized collision cell conditions. The detection limit for arsenic () obtained in difficult hydrochloride acid matrix (5% HCl (v/v)) was 153 ng l⁻¹. The accuracy of the optimized method was confirmed by analyzing two moss reference materials. The results obtained by ICP-MS for arsenic, selenium and iron from both moss reference samples were, in most cases, in good agreement with the certified values.     

Voltammetric determination of L-dopa using an electrode modified with trinuclear ruthenium ammine complex (Ru-red) supported on Y-type zeolite

The L-dopa is the immediate precursor of the neurotransmitter dopamine. Unlike dopamine, L-dopa easily enters the central nervous system and is used in the treatment of Parkinson’s disease. A sensitive and selective method is presented for the voltammetric determination of L-dopa in pharmaceutical formulations using a carbon paste electrode modified with trinuclear ruthenium ammine complex [(NH₃)₅Ru^IIIORu^IV(NH₃)₄ORu^III(NH₃)₅]⁶⁺ (Ru-red) incorporated in NaY zeolite. The parameters which influence on the electrode response (paste composition, potential scan rate, pH and interference) were also investigated. The optimum conditions were found to an electrode composition (m/m) of 25% zeolite containing 6.7% Ru, 50% graphite and 25% mineral oil in acetate buffer at pH 4.8. Voltammetric peak currents showed a linear response for L-dopa concentration in the range between 1.2×10⁻⁴ and 1.0×10⁻² mol l⁻¹ (r=0.9988) with a detection limit of 8.5×10⁻⁵ mol l⁻¹. The variation coefficient for a 1.0×10⁻³ mol l⁻¹ L-dopa (n=10) was 5.5%. The results obtained for L-dopa in pharmaceutical formulations (tablet) was in agreement with compared official method. In conclusion, this study has illustrated that the proposed electrode modified with Ru-red incorporated zeolite is suitable valuable for selective measurements of L-dopa.