Preparation and characterization of p-tert-butylcalix[8]arene bonded capillaries for open-tubular capillary electrochromatography

p-tert-Butylcalix[8]arene bonded capillaries for open-tubular capillary electrochromatography were prepared with γ-glycidoxypropyltrimethoxysilane as a bridge. The bonded capillary displayed low and steady electroosmotic flow (EOF) values over the pH range from 4 to 9. Detection limits for direct spectrophotometric detection at 277 nm for benzenediols (at a signal to noise ratio of 2) were 0.96 mg l⁻¹ for the unbonded capillary and 1.48 mg l⁻¹ for the bonded capillary, showing that the bonded layer did not show significant absorbance and hence decreased sensitivity. The bonded capillaries showed good separation selectivity for o-, m- and p-benzenediols, α- and β-naphthols, and α- and β-naphthylamines. This selectivity was attributed to significant interactions between the analytes and the bonded p-tert-butylcalix[8]arene, which contributed to the electrochromatographic separation mechanism. The bonded capillaries gave high stability and reproducibility.     

Synthesis and dichromate anion extraction ability of p-tert-butylcalix[4]arene diamide derivatives with different binding sites

The article describes the synthesis and evaluation of the dichromate anion (Cr₂O₇²⁻/HCr₂O₇⁻) extraction properties of p-tert-butylcalix[4]arene diamide derivatives (5-7) containing different binding sites. Among these compounds, 6 and 7 have been synthesized via aminolysis in a toluene-methanol solvent system with 3-aminomethylpyridine and 3,6-dioxa-1,8-diamino octane, respectively. On the other hand, compound 5 has been synthesized via an acid chloride method due to its inefficiency under aminolysis. The extraction properties of these diamides toward dichromate anions are studied by liquid-liquid extraction. The results show that p-tert-butylcalix[4]arene diamide derivative 7 exhibited a much higher affinity toward dichromate anions than that of 6 due to its special structure, while 5 was an ineffective ligand for these anions.     

Langmuir-Blodgett film of p-tert-butylthiacalix[4]arene modified glassy carbon electrode as voltammetric sensor for the determination of Hg(II)

The π-A isotherms and UV-vis spectra of the transferred films suggested that the monolayer of p-tert-butylthiacalix[4]arene can coordinate with Hg²⁺ at the air-water surface. From these observations, a glassy carbon electrode coated with Langmuir-Blodgett film of p-tert-butylthiacalix[4] arene as a new voltammetric sensor is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode and modified glassy carbon electrode using direct coating method, the Langmuir-Blodgett film-modified electrode can greatly improve the measuring sensitivity of Hg²⁺. Under the selected conditions, the Langmuir-Blodgett film-modified electrode in 0.1 mol L⁻¹ H₂SO₄ + 0.01 mol L⁻¹ KCl solution shows a linear voltammetric response for Hg²⁺ in the range of 5.0 × 10⁻¹⁰ to 1.5 × 10⁻⁷ mol L⁻¹, with a detection limit of 2.0 × 10⁻¹⁰ mol L⁻¹. The proposed method was also applied to determine Hg²⁺ in water samples (tap, lake and river water). In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility and good stability.     

Regioselective ipso formylation of p-tert-butylcalix[4]arene

A convenient procedure for direct introduction of one formyl group into p-tert-butylcalix[4]arenes through ipso substitution is described.     

Novel potentiometric membrane sensor based on 6-(4-nitrophenyl)-2-phenyl-4,4-dipropyl-3,5-diaza-bicyclo[3,1,0] hex-2-ene for detection of strontium (II) ions at trace levels

A new PVC membrane strontium ion-selective electrode has been constructed using 6-(4-nitrophenyl)-2-phenyl-4,4-dipropyl-3,5-diaza-bicyclo[3,1,0] hex-2-ene (NPDBH) as a neutral ionophore. The electrode was prepared with 7% NPDBH (as ionophore), 57% acetophenone (as plasticizer), 30% PVC and 6% oleic acid (as lipophilic additive). The electrode responds to Sr²⁺ ion with a sensitivity of 28.2 ± 0.5 mV/decade over the range 1.0 × 10⁻⁶-1.0 × 10⁻¹ mol L⁻¹ and in a pH range of 3.0-10.0. The limit of detection was 2.4 × 10⁻⁷ mol L⁻¹. It has a response time of <20 s and can be used for at least three months without any divergence in potentials. The proposed electrode shows good discrimination of Sr²⁺ ion from several cations. The effect of organic solvents on electrode response was examined. The results show that this electrode can be used in ethanol media up to 15% (v/v) concentration without interference. The isothermal temperature coefficient of this electrode amounted to 0.00019 V/°C. The electrode was found to work well under laboratory conditions. It was successfully applied to the determination of strontium ions in human urine and bone digests.     

Batch and flow measurement of hydrogen ions in highly acidic media using 2-(4-methoxy phenyl) 6-(4-nitrophenyl)-4-phenyl-1,3-diazabicyclo [3.1.0] hex-3-ene as an H-selective ionophore

A hydrogen ion-selective poly(vinyl chloride) (PVC) membrane electrode was developed using 2-(4-methoxy phenyl) 6-(4-nitrophenyl)-4-phenyl-1,3-diazabicyclo [3.1.0] hex-3-ene as ionophore. Effects of experimental parameters such as membrane composition, nature and amount of plasticizer, and the amount of additive on the potential response of pH sensor were investigated. This H⁺-selective membrane electrode gave a linear response over the pH range 0-4 (10⁻⁴ to 1 mol L⁻¹ HCl) with slope of 57.4 ± 0.3 mV pH⁻¹ and limit of detection 6.3 × 10⁻⁵ mol L⁻¹ at 20 °C. Also, hydrofluoric acid did not influence the surface of this electrode and thus it was maintained without showing any changes in potentials after being used in a hydrofluoric acid solution. The equilibrium water content of the electrode was determined in the presence of two different plasticizers as membrane solvent. The alkaline cation binding affinity of ionophore was very low that prove these cations do not have specific interaction with this ionophore. The electrode had fairly low electrical resistance, good potential stability and reproducibility. It has a rapid potential response to changes of pH (10 s), easily used in a single channel wall-jet flow injection system with good reproducibility (RSD% = 1.67%) and high reversibility. It was used as indicator electrode in potentiometric determination of pH in real samples.     

Determination of cefuroxime axetil in tablets and biological fluids using liquid chromatography and flow injection analysis

In the present work, the separations of calixarene derivatives have been investigated using both high-performance liquid chromatography (HPLC) and nonaqueous capillary electrophoresis (NACE) techniques. HPLC-1 method with LC-318 (pore size = 300 Å) column and MeCN mobile phase was optimized for the separation of calixarenes. At the flow-rate of 1 ml/min p-nitrocalix[6]arene, calix[4]arene and calix[6]arene could be well baseline and symmetrically separated within 5 min. For the separation of p-tert-butylcalix[n]arenes (n = 4, 6, 8), HPLC-2 and NACE methods have been optimized. The optimal conditions in HPLC-2 method included NH₂ column and MeCN mobile phase, and p-tert-butylcalix[n]arenes (n = 4, 6, 8) were baseline separated within 10 min at 0.8 min/min. The optimal conditions for NACE method employed MeCN-H₂O (8:2, v/v) as the nonaqueous medium and 120 mM Tris/HCl (pH 9.0) as the buffer, and p-tert-butylcalix[n]arenes (n = 4, 6, 8) were successfully baseline resolved within 16 min. With the detection at 280 nm, the calibration lines were linear in the ranges of 1-200 μg/ml for calixarene derivatives by HPLC-1 and HPLC-2 methods, and of 2.5-200 μg/ml for p-tert-butylcalix[n]arenes (n = 4, 6, 8) by NACE method, respectively. The detection limits (S/N = 3) and recoveries ranged from 0.5 to 1.4 μg/ml and from 98.1 to 102.4% by both HPLC-1 and HPLC-2 methods, and from 1.3 to 2.0 μg/ml and from 97.9 to 105.1% by NACE method, respectively. The intra-day reproducibility of the methods was determined with satisfactory results. The proposed HPLC and NACE methods were accurate and reproducible, and could be utilized to separate and determine calixarene derivatives.     

Hg-selective fluoroionophore of p-tert-butylcalix[4]arene-diaza-crown ether having pyrenylacetamide subunits

A new ionophore having two pyrenylacetamide moieties based on the p-tert-butylcalix[4]arene-diaza-crown ether has been prepared and its fluoroionophoric properties were investigated. Bis(pyrenyl) derivative was found to exhibit selective ON-OFF type sensing behavior toward Hg²⁺ ions over other representative transition and heavy metal ions. The fluorescence quenching efficiency of larger than 20-fold was observed with 100 equiv of Hg²⁺ ions and the association constant was found to be 4.5 × 10⁴ M⁻¹ in methanol. The ionophore also exhibited a very efficient quenching of excimer fluorescence selectively upon treatment with Hg²⁺ ions in 50% aqueous methanol solution. The observed Hg²⁺-selective ON-OFF type fluorescence behavior could be utilized as efficient sensing and switching devices for the design of other supramolecular systems.     

Copper(II)-selective electrode based on dithioacetal

A PVC membrane electrode for copper ion based on 1,3-dithiane,2-(4-methoxy phenyl) as ionophore and o-nitrophenyl octyl ether as a plasticizer is demonstrated. The electrode exhibits a Nernstian slope of 29.5±1 mV per decade in a linear range of 3.0×10⁻⁶ to 5.0×10⁻² M for Cu²⁺ ion. The detection limit of this electrode is 1.0×10⁻⁶ mol/l. This sensor has a very short response time of about 5 s and could be used in a pH range of 4.0-7.0. High selectivity was obtained over a wide variety of metal ions. The proposed electrode was successfully applied as an indicator electrode for the potentiometric titration of copper ion with EDTA and for the direct determination of copper in river water.     

Determination of bisphenol A, 4-n-nonylphenol, and 4-tert-octylphenol by temperature-controlled ionic liquid dispersive liquid-phase microextraction combined with high performance liquid chromatography-fluorescence detector

Present study described a simple, sensitive, and viable method for the determination of bisphenol A, 4-n-nonylphenol and 4-tert-octylphenol in water samples using temperature-controlled ionic liquid dispersive liquid-phase microextraction coupled to high performance liquid chromatography-fluorescence detector. In this experiment, 1-octyl-3-methylimidazolium hexafluorophosphate ([C₈MIM][PF₆]) was used as the extraction solvent, and bisphenol A, 4-n-nonylphenol and 4-tert-octylphenol were selected as the model analytes. Parameters affecting the extraction efficiency such as the volume of [C₈MIM][PF₆], dissolving temperature, extraction time, sample pH, centrifuging time and salting-out effect have been investigated in detail. Under the optimized conditions, good linear relationship was found in the concentration range of 1.0-100 μg L⁻¹ for BPA, 1.5-150 μg L⁻¹ for 4-NP, and 3-300 μg L⁻¹ for 4-OP, respectively. Limits of detection (LOD, S/N = 3) were in the range of 0.23-0.48 μg L⁻¹. Intra day and inter day precisions (RSDs, n = 6) were in the range of 4.6-5.5% and 8.5-13.3%, respectively. This method has been also successfully applied to analyze the real water samples at two different spiked concentrations and excellent results were obtained.     

Solid phase microextraction procedure for the determination of alkylphenols in water by on-fiber derivatization with N-tert-butyl-dimethylsilyl-N-methyltrifluoroacetamide

The solid phase microextraction (SPME) technique with on-fiber derivatization was evaluated for the analysis of alkylphenols (APs), including 4-tert-octylphenol (4-t-OP), technical nonylphenol isomers (t-NPs) and 4-nonylphenol (4-NP), in water. The 85 μm polyacrylate (PA) fiber was used and a two-step sample preparation procedure was established. In the first step, water sample of 2 mL was placed in a 4 mL PTFE-capped glass vial. Headspace extraction of APs in water was then performed under 65 °C for 30 min with 800 rpm magnetic stirring and the addition of 5% of sodium chloride. In the second step, the SPME fiber was placed in another 4 mL vial, which contained 100 μL of N-tert-butyl-dimethylsilyl-N-methyltrifluoroacetamide (MTBSTFA) with 1% tert-butyl-dimethylchlorosilane (TBDMCS). Headspace extraction of MTBSTFA and on-fiber derivatization with APs were performed at 45 °C for 10 min. Gas chromatography/mass spectrometry (GC/MS) was used for the analysis of derivatives formed on-fiber. The adsorption-time profiles were also examined. The precision, accuracy and method detection limits (MDLs) for the analysis of all the APs were evaluated with spiked water samples, including detergent water, chlorinated tap water, and lake water. The relative standard deviations were all less than 10% and the accuracies were 100 ± 15%. With 2 mL of water sample, MDLs were in the range of 1.58-3.85 ng L⁻¹. Compared with other techniques, the study described here provided a simple, fast and reliable method for the analysis of APs in water.     

Strontium(II)-selective electrode based on a macrocyclic tetraamide

A new PVC membrane electrode based on 5,7,12,14-dibenzo-2,3,9,10-tetraoxa-1,4,8,11-tetraazacyclotetradecane (I) as an ion carrier, o-nitrophenyloctyl ether (o-NPOE) as solvent mediator and sodium tetraphenylborate (NaTPB) as lipophilic additive was fabricated and investigated as Sr²⁺-selective electrode. The best performance was exhibited by the membrane having composition 8:200:4:120 (I:o-NPOE:NaTPB:PVC). The electrode exhibited a Nernstian response for strontium ion over a wide concentration range 3.98 × 10⁻⁶ to 1.0 × 10⁻¹ M with a slope of 29.0 ± 0.1 mV/decade of concentration and a detection limit of 2.82 × 10⁻⁶ M. It showed a response time of less than 10 s and could be used for at least 3 months without any divergence in potential. The proposed electrode showed a good discriminating ability towards strontium(II) ion over a wide variety of other metal ions including alkali, alkaline earth, transition, and heavy metal ions. The electrode can be used in the pH range of 2.5-10.5 and in mixtures containing up to 35% (v/v) non-aqueous content. It was used as an indicator electrode in potentiometric titration of strontium ion against EDTA.     

A highly selective thallium(I) electrode based on a thia substituted macrocyclic ionophore

A new highly Tl(I)-selective PVC membrane electrode based on tetrathia macrocycle 6,7: 14,15-dibenzo-5,8,13,16-tetraoxo-1,4,9,12-tetrathiacyclohexadecane [Bz₂O₄(16)aneS₄] (I) as membrane carrier, o-nitrophenyloctyl ether (o-NPOE) as solvent mediator and potassium tetrakis(p-chlorophenyl)borate (KTpClPB) as lipophilic additive has been developed. The best performance was given by the membrane of macrocycle (I) with composition 3:120:1.5:50 (I:o-NPOE:KTpClPB:PVC). This electrode exhibits a Nernstian response to Tl(I) ions in the concentration range 1.0 × 10⁻¹-2.23 × 10⁻⁶ M with a slope of 58.2 mV/decade of concentration and a detection limit of 1.58 × 10⁻⁶ M. The response time of the sensor is 12 s and can be used over a period of 4 months with good reproducibility. The proposed electrode revealed good selectivity over a wide variety of other cations including alkali, alkaline earth, heavy and transition metals. The electrode works well over a pH range of 3.2-11.5 and in partially non-aqueous medium with up to 30% organic content. The sensor was also used as an indicator electrode in potentiometric titration of Tl(I) ions with KI solution.     

Lead-selective fluorescent optode membrane based on 3,3′,5,5′-tetramethyl-N-(9-anthrylmethyl)benzidine

A new proton-selective fluorescing indicator, 3,3′,5,5′-tetramethyl-N-(9-anthrylmethyl)benzidine (TMANB) has been synthesized and applied in an optode membrane for the determination of lead ion that works on the basis of a cation-exchange mechanism. When embedded in a plasticized poly(vinyl chloride) (PVC) membrane containing lead ionophore (tert-butylcalix[4]arene-tetrakis(N,N-dimethylthioacetamide)) and a lipophilic anionic site [potassium tetrakis(4-chlorophenyl)borate], TMANB shows a significant fluorescence signal change on exposure to aqueous HCl solution containing lead ion, which exhibits the theoretically expected fluorescence response to lead ion concentration. The selectivity, response time, reproducibility and reversibility, and lifetime of the optode membrane were discussed.     

Preparation of p-nitrocalix[n]arene methyl ethers via ipso-nitration and crystal structure of tetramethoxytetra-p-nitrocalix[4]arene

Nitration of p-tert-butylcalix[n]arene methyl ethers under a variety of reaction conditions has been examined. It has been determined that amongst different nitration procedures adopted (AlCl₃/KNO₃, HNO₃/CH₃COOH, HNO₃/(CH₃CO)₂O, cerium(IV) ammonium nitrate/CH₃COOH), ipso-nitration with CH₃COOH/HNO₃ gives best yields of p-nitrocalixarenes and work up conditions. ipso-Nitration of tetramethoxytetra-p-tert-butylcalix[4]arene gives tetramethoxytetra-p-nitrocalix[4]arene as triclinic crystals with space group with a=9.102(3) Å, b=11.623(3) Å, c=18.368(3) Å and α=77.99(2)°, β=81.10(2)°, γ=73.37(2)°. Its conformation is partial cone and it forms an exocylic 1:1 complex with DMF.     

A PVC-membrane bulk optode for gallium(III) ion determination

An optical probe responsive to gallium(III) ion has been developed. The gallium sensing system was prepared by incorporating 4-(p-nitrophenyl azo)-pyrocatechol (NAP) as ionophore in a plasticized PVC membrane containing tributylphosphate (TBP) as plasticizer. The sensing membrane in contact with gallium ion at pH 3.5, changes color from yellow-brown to pink-brown. Under optimum conditions, the proposed membrane displayed a linear range of 5-83 μM with a limit of detection of 4 μM. The response time of the membrane was within 10-15 min depending on the concentration of Ga³⁺ ions. The selectivity of the probe towards gallium determination was found to be very good. Experimental results showed that the probe could be used as an effective tool in analyzing the gallium content of water samples.     

A new beryllium ion-selective membrane electrode based on dibenzo(perhydrotriazino)aza-14-crown-4 ether

Beryllium(II) selective electrodes have been fabricated based on poly(vinyl chloride) (PVC) matrix membranes containing newly synthesized neutral carrier dibenzo(perhydrotriazino)aza-14-crown-4 ethers as ionophore. Best performance was exhibited by the membrane having a composition ionophore (IIa):PVC:sodium tetraphenylborate (NaTPB):tributyl phosphate (TBP) in the ratio (w/w; mg) of 5:30:3:65. This membrane worked well over a wide concentration range 7.6 × 10⁻⁶ to 1.0 × 10⁻¹ M of Be²⁺ with a Nernstian slope of 30.7 mV per decade of beryllium activity. The response time of the sensor is 15 s and the membrane can be used over a period of 4 months with good reproducibility. The proposed electrode works well in a wide pH range 3.0–9.0. It was successfully applied to the determination of beryllium in a mineral sample.     

p-tert-Butyl thiacalix[4]arenes functionalized at the lower rim by o-, m-, p-amido and o-, m-, p-(amidomethyl)pyridine fragments as receptors for α-hydroxy- and dicarboxylic acids

A series of new p-tert-butyl thiacalix[4]arenes with o-, m-, p-amido and o-, m-, p-(amidomethyl)pyridine substituents at the lower rim in cone, partial cone, and 1,3-alternate conformations were synthesized. The ability of the obtained compounds to recognize the α-hydroxy (glycolic, tartaric) and dicarboxylic (oxalic, malonic, succinic, fumaric, and maleic) acids was investigated by UV-vis spectroscopy. Also, the efficiency and selectivity of binding, the association constants log K_a (10² to 10⁷ M⁻¹) and the stoichiometry were determined for the complexes of p-tert-butyl thiacalix[4]arenes with the acids. The receptors based on p-tert-butyl thiacalix[4]arenes with (amidomethyl)pyridine substitutes are most efficient in complexation in many cases.     

Design and evaluation of a thorium (IV) selective optode

A novel optical sensor has been proposed for sensitive determination of thorium (IV) ion in aqueous solutions. The thorium sensing membrane was prepared by incorporating 4-(p-nitrophenyl azo)-pyrocatechol (NAP) as ionophore in the plasticized PVC membrane containing tributyl phosphate (TBP) as plasticizer. The membrane responds to thorium ion by changing color reversibly from yellow to red-brown in glycine buffer solution at pH 3.5. The proposed sensor displays a linear range of 8.66 × 10⁻⁶-2.00 × 10⁻⁴ M with a limit of detection of 6 × 10⁻⁶ M. The response time of the optode was about 8.8-12.5 min, depending on the concentration of Th (IV) ions. The selectivity of optode to Th (IV) ions in glycine buffer is good. The sensor can readily be regenerated by exposure to a solution mixture of sodium fluoride and 5-sulfosalicylic acid (dihydrate) (0.01 M each). The optode is fully reversible. The proposed optode was applied to the determination of thorium (IV) in environmental water samples.     

Copper(I)-bathocuproine complex as carrier in iodide-selective electrode

A PVC membrane electrode for iodide ions based on Cu(I)-bathocuproine as ionophore in membrane composition is prepared. The electrode exhibits a linear response over a wide concentration range 5.0×10⁻⁶ to 2.0×10⁻¹ mol l⁻¹ with a detection limit 1.0×10⁻⁶ mol l⁻¹. The proposed membrane electrode shows Nernstian behavior with a slope of −56.8 mV/decade, a fast response time 10 s and a lifetime at least 3 months. Iodide-selective electrode reveals good selectivities for iodide ion over a wide variety of the other anions and can be used in pH range of 3-9. It can also be used as an indicator electrode in potentiometric titration of iodide ion.