Rapid determination of lead extracted by acetic acid from glazed ceramic surfaces by flow injection on-line preconcentration and spectrophotometric detection

A rapid method has been developed for the determination of lead extracted by acetic acid from glazed ceramic surfaces by flow injection analysis without any pretreatment. An aliquot of 4% acetic acid solution, which has been kept in a teacup for 24 h in the dark, is injected into a carrier solution (1 M nitric acid) and passed through a Pb-Spec resin column. After washing the column with an ammonium nitrate solution, the lead adsorbed on the column is eluted with an ammonium oxalate solution and then merged with a 4-(2-pyridylazo)resorcinol (PAR) solution, followed by measurement of the absorbance of the lead-PAR complex at 530 nm. The detection limit, concentration giving a signal equal to three times the standard deviation of the blank signal, is 8 ng ml⁻¹. The relative standard deviation of measurements at the 0.8 μg ml⁻¹ level is 0.35% (n = 5). The sample throughput is 12 per hour.     

Ion chromatographic determination of trace amounts of aluminium with on-line preconcentration and spectrophotometric detection

Trace amounts of aluminium in aqueous samples can be determined by ion chromatography using ammonium sulphate-nitric acid as eluent and pyrocatechol violet as post-column chromogenic reagent. The detection limit for a 50-μl sample is 10 μg 1^?1. Preconcentration of the sample (obtained by replacing the sampling loop with a short ion-exchange column) allows larger amounts of sample to be loaded and lowers the detection limit below 1 μg 1^?1.     

Factorial design in the optimization of preconcentration procedure for lead determination by FAAS

The present paper proposes a preconcentration procedure for lead determination using flame atomic absorption spectrometry (FAAS). It is based on lead(II) ions extraction as brilliant cresyl blue (BCB) complex and its sorption onto Diaion HP-2MG, a methacrylic ester copolymer. The optimization step was carried out using factorial design and the variables studied were pH, shaking time and reagent concentration. In the established experimental conditions, lead can be determinate with a limit of detection of 3.7 μg L⁻¹ lead (N = 20) and a relative standard deviation of 7% for a lead concentration of 100 μg L⁻¹. The accuracy was confirmed by analysis of a certified reference material, the stream sediment furnished by National Research Centre for Certified Reference Materials (NRCCRM), China (GBW 07310). Effect of other ions in the procedure proposed was also studied. The method was applied for lead determination in real samples of water, tea, soil and dust. Tests of addition/recovery in the experiments for lead determination in water samples revealed that the proposed procedure could be applied satisfactorily for analysis of these samples.     

Investigation of on-line coupling electrothermal atomic absorption spectrometry with flow injection sorption preconcentration using a knotted reactor for totally automatic determination of lead in water samples

A flow injection on-line sorption preconcentration electrothermal atomic absorption spectrometric system for fully automatic determination of lead in water was investigated. The discrete non-flow-through nature of ETAAS, the limited capacity of the graphite tube and the relatively large volume of the knotted reactor (KR) are obstacles to overcome for the on-line coupling of the KR sorption preconcentration system with ETAAS. A new FI manifold has been developed with the aim of reducing the eluate volume and minimizing dispersion. The lead diethyldithiocarbamate complex was adsorbed on the inner walls of a knotted reactor made of PTFE tubing (100 cm long, 0.5 mm i.d.). After that, an air flow was introduced to remove the residual solution from the KR and the eluate delivery tube, then the adsorbed analyte chelate was quantitatively eluted into a delivery tube with 50 μl of ethanol. An air flow was used to propel the eluent from the eluent loop through the reactor and to introduce all the ethanolic eluate onto the platform of the transversely heated graphite tube atomizer, which was preheated to 80°C. With the use of the new FI manifold, the consumption of eluent was greatly reduced and dispersion was minimized. The adsorption efficiency was 58%, and the enhancement factor was 142 in the concentration range 0.01–0.05 μg l⁻¹ Pb at a sample loading rate of 6.8 ml min⁻¹ with 60 s preconcentration time. For the range 0.1–2.0 μg l⁻¹ of Pb a loading rate of 3.0 ml min⁻¹ and 30 s preconcentration time were chosen, resulting in an adsorption efficiency of 42% and an enhancement factor of 21, respectively. A detection limit (3σ) of 2.2 ng l⁻¹ of lead was obtained using a sample loading rate of 6.8 ml min⁻¹ and 60 s preconcentration. The relative standard deviation of the entire procedure was 4.9% at the 0.01 μg l⁻¹ Pb level with a loading rate of 6.8 ml min⁻¹ and 60 s preconcentration, and 2.9% at the 0.5 μg l⁻¹ Pb level with a 3.0 ml min⁻¹ loading rate and 30 s preconcentration. Efficient washing of the matrix from the reactor was critical, requiring the use of the standard addition method for seawater samples. The analytical results obtained for seawater and river water standard reference materials were in good agreement with the certified values.     

Flow injection preconcentration by chemofiltration and spectrophotometric determination of Gd

A new on-line Gd preconcentration and determination system associated to flow injection (FI) method was developed. 2,2′-(1,8-dihydroxy-3,6-disulfonaphthylene-2,7-bisazo) bisbenzenearsonic acid (Arsenazo III) was used as a complexing agent at pH 2.5. A reactor containing the polyamide membrane was used for the retention of the Gd complex by chemofiltration. The complex was then removed from the reactor with buffer solution pH 9. The variables affecting the combined on-line preconcentration-absorptiometric method have been evaluated and optimised. The coupling of the on-line preconcentration and spectrophotometric flow through detection led to a detection limit of 15 μg l⁻¹ for a preconcentration time of 5 min at 2 ml/min. The method was successfully applied to biological samples.     

Cloud-point extraction/preconcentration on-line flow injection method for mercury determination

A cloud-point extraction/preconcentration (CPE/P) step is incorporated on-line into a flow injection system which is used to determine low levels of Hg(II) added to natural water samples. The analyte is complexed with dithizone. A solid reagent column (SRC) is used to prepare the reagent on-line by using 5% (v/v) Triton X-100 solution as solvent. The CPE/P is carried out by using the non-ionic surfactant Triton X-100. After obtaining the cloud-point on-line, the surfactant-rich phase containing the complex is collected in a mini column packed with cotton wool. Then, a hot water stream is passed through the column to elute the complex and the absorbance is measured at 500 nm.All the flow and chemical variables are optimized and the enhancement factor for the system is estimated. The calibration is linear over the range 0.05-0.5 μg ml⁻¹, the R.S.D. is 4.8%, the limit of detection (signal:noise = 3) is 0.014 μg ml⁻¹ and the sample throughput is 30 h⁻¹. An open/closed system is used to eliminate the interference of iron(III).     

Use of silica gel chemically modified with zirconium phosphate for preconcentration and determination of lead and copper by flame atomic absorption spectrometry

An analytical method using silica gel chemically modified with zirconium (IV) phosphate for preconcentration of lead and copper, in a column system, and their sequential determination by flame atomic absorption spectrometry (FAAS), was developed. Sample solutions are passed through a glass column packed with 100 mg of the sorbent material, at pH 4.5, and lead and copper are eluted with 1.0 mol l⁻¹ HNO₃ at a flow rate of 2.0 ml min⁻¹. The extraction of copper is affected by Fe(II), Mn(II), Zn(II), Ni(II) and Co(II) while only Fe(II) interferes in the lead determination. These interferences may be overcome with an appropriate addition of a KI or NaF solution. An enrichment factor of 30 was obtained for both metals. While the limits of detection (3σ) were 6.1 and 1.1 μg l⁻¹, for Pb and Cu, respectively, the limits of determination were 16.7 and 3.3 μg l⁻¹. The precision expressed as relative standard deviation (R.S.D.) obtained for 3.3 μg l⁻¹ of Cu and 16.7 μg l⁻¹ of Pb were 4.3 and 4.7%, respectively, calculated from ten measurements. The proposed method was evaluated with reference material and was applied for the determination of lead and copper in industrial and river waters.     

Flow-injection spectrophotometric determination of chloramben

Abstract

A method for the dechlorination of PCB mixtures (Aroclor formulations) to biphenyl was extended to soils. The contaminated sample was mixed with magnesium flakes, potassium hexachloropalladiate (K₂PdCl₆), propan-2-ol and water then permitted to react for up to six hours. Biphenyl, recovered by extraction into hexane, was quantified by gas chromatography with flame ionization detection. The reaction was very efficient in propan-2-ol / water (～95%), surfactant emulsion or sand mixture and virtually complete in soil provided that excess magnesium (2 g) and the K₂PdCl₆ were added to the sample prior to the addition of water. Higher PCB loadings were readily determined in field contaminated soils either by direct determination within the matrix or by standard additions. However, analyte concentrations were appreciably over-estimated in Soxhlet or sonication extracts of a certified reference material that contained sub-ppm levels of analyte. The over-estimation is considered to result from the conversion in part of natural organic matter to biphenyl.     

Clean analytical methodology for the determination of lead with Arsenazo III by cyclic flow-injection analysis

A clean analytical methodology, where the sample determined and the reagent used are both toxic, has been proposed. A cation exchange mini-column was incorporated after the flow-through cell for on-line regeneration of the main reagent and the accumulation of heavy metal ions. The method involves the spectrophotometric determination of lead with Arsenazo III, the accumulation of lead onto the cationic exchanger, and subsequent regeneration of the chromogenic reagent, which makes the system reversible and the reagents reusable. The developed method provides a satisfactory way to cut down on the toxic reagent consumption and the produced volume of waste, an important step towards the zero emissions research initiative concept. The excellent repeatability and reproducibility, and the simplicity of this method are well suited for continuous measurements. The method was successively applied to the assay of lead in high-octane gasoline.     

Trace gold determination by on-line preconcentration with flow injection atomic absorption spectrometry

A reverse-phase extraction column method has been employed as an on-line preconcentration technique for trace gold analysis by flame atomic absorption spectrometry. Di(methylheptyl)methyl phosphonate (DMHMP) loaded onto a macroporous resin was used as the immobilized phase. A thiourea-HCl solution was found successful in eluting the gold. The experimental parameters were optimized by Simplex Optimization, with 17 tests needed to obtain optimal conditions. Sensitivities of 5.2 mug/l. and 2.3 mug/l., with sample frequencies of 45/hr and 48/hr, were obtained by using single and dual-columns respectively. The recoveries for mixed composition samples were 93-110%.     

A new flow injection preconcentration method based on multiwalled carbon nanotubes for the ETA-AAS determination of Cd in urine

A new flow injection (FIA) procedure for the preconcentration of cadmium in urine using multiwalled carbon nanotubes (MWCNT) as sorbent and posterior electrothermal atomization atomic absorption spectrometry (ETA-AAS) Cd determination has been developed. Cadmium was retained in a column filled with previously oxidized MWCNTs and it was quantitatively eluted with a nitric acid solution. The parameters influencing the adsorption-elution process such as pH of the sample solution, amount of sorbent and flow rates of sample as well as eluent solutions have been studied. Cd concentration in the eluent was measured by ETA-AAS under the optimized conditions obtained. The results indicated the elimination of urine matrix effect as a consequence of the preconcentration process performed. Total recovery of cadmium from urine at pH 7.2 using a column with 45 mg of MWCNTs as sorbent and employing a HNO₃ 0.5 mol L⁻¹ solution for elution was attained. The detection limit obtained was 0.010 μg L⁻¹ and the preconcentration factor achieved was 3.4. The method showed adequate precision (RSD: 3.4-9.8%) and accuracy (mean recovery: 97.4-100%). The developed method was applied for the determination of cadmium in real urine samples from healthy people (in the range of 0.14-2.94 μg L⁻¹) with satisfactory results.     

A comparison of preconcentration reagents for flow injection analysis flame atomic spectrometry

A small range of new commercially available chelating resins are compared with a resin prepared in-house in terms of their applicability for on-line preconcentration and matrix separation. The flow injection manifold was designed for rapid matrix separation and the resins were tested for the determination of Cull, ZnII, CdII, MnII and NiII. The resin based on controlled pore glass was found to be better for this rapid procedure because it did not require conditioning, although the polymer based resins had better capacities. The commercially available controlled pore glass based iminodiacetate (IDA) resin had a comparable performance to the in-house controlled pore glass 8-hydroxyquinoline (CPG-8-HQ) resin. The IDA resin had a much higher capacity than the 8-HQ, however as with all IDA based resins, some retention of Call was observed. The sample throughput was 12 h⁻¹.     

A simple and sensitive chromium speciation procedure by hyphenating flow injection on-line preconcentration with catalytic spectrophotometry

A high sensitive chromium speciation procedure based on spectrophotometric detection was developed by coupling flow injection on-line preconcentration with a catalytic indicator reaction. Chromium(VI) is retained on a mini-column packed with polystyrene anion exchange resin (strong basic 717 resin), which was afterwards eluted with a small volume of NaNO₃ solution. The eluted Cr(VI) is then directed to catalyze the decoloration of alizarin cyanine green (ACG) in the presence of bromate as oxidizing reagent, and the absorbance change is proportional to the concentration of Cr(VI). With a sampling volume of 12 ml and a loading time of 120 s, an enrichment factor of 26.5 was achieved for the preconcentration. The most distinct feature of this procedure is characterized by its overall detection limit, i.e., 50 ng l⁻¹, which is much superior to those achieved by FAAS, and comparable to those obtained by inductively coupled plasma mass spectrometry (ICPMS) and electrothermal atomic absorption spectrometry (ETAAS). The procedure was validated with a certified reference material. It was also applied to the speciation of chromium in a series of surface water samples.     

Factorial design for multivariate optimization of preconcentration system for spectrophotometric phosphorus determination

The present paper proposes a preconcentration procedure for phosphorus determination by using ultraviolet-visible spectrophotometer. It is based on the formation of phosphomolybdate and its reduction to molybdenum blue. Phosphorus extraction as phosphomolybdenum blue complex was performed onto Amberlite XAD-4. The optimization step was carried out using two-level full factorial design. Three variables (resin amount, sample volume, flow rate) were regarded as factors in the optimization. The relative standard deviation was 2% at 0.08 μg mL⁻¹. The limit of detection was found to be 2.23 μg L⁻¹ (N = 15). The proposed solid-phase extraction procedure was applied to phosphorus in some fruit leaves, natural waters, and a standard reference material (SRM 1515 apple leaves).     

Simultaneous on-line preconcentration and determination of trace metals in environmental samples using a modified nanometer-sized alumina packed micro-column by flow injection combined with ICP-OES

A novel organic reagent 3-(8-quinolinylazo)-4-hydroxybenzoic acid (QAHBA) was synthesized for chemically modified nanometer-sized alumina, and it was characterized with infrared spectrum and ¹H NMR spectra. By using modified nanometer-sized alumina as micro-column packing material, a new method of flow injection (FI) on-line preconcentration coupled to ICP-OES was developed for simultaneous determination of trace metals (Ag, Pd, Au, Ga, In and Nb) in geological and environmental samples. The effects of pH, sample flow rate, sample volume, elution and interfering ions on the recovery of the analytes have been investigated. Under the optimized operating conditions, the adsorption capacity of the modified nanometer-sized alumina for Ag, Pd, Au, Ga, In and Nb were found to be 5.1, 7.6, 17.7, 15.6, 8.1 and 12.3 mg g⁻¹, respectively. With 4 min preconcentration time and 24 s elution time, the enrichment factor was 10 and the sample frequency was 10 h⁻¹. The detection limits of this method for Ag, Pd, Au, Ga, In and Nb were 0.12, 0.44, 0.27, 0.19, 0.54 and 0.18 μg l⁻¹, respectively, while the R.S.D.s were 1.6, 2.3, 4.5, 1.6, 1.9 and 1.7% (n = 7, c = 50 ng ml⁻¹), respectively. The proposed method has been applied to the determination of these trace metals in geological-certified reference materials and natural water samples with satisfactory results.     

Mobility-based selective on-line preconcentration of proteins in capillary electrophoresis by controlling electroosmotic flow

A simple method to perform selective on-line preconcentration of protein samples in capillary electrophoresis (CE) is described. The selectivity, based on protein electrophoretic mobility, was achieved by controlling electroosmotic flow (EOF). A short section of dialysis hollow fiber, serving as a porous joint, was connected between two lengths of fused silica capillary. High voltage was applied separately to each capillary, and the EOF in the system was controlled independently of the local electric field intensity by controlling the total voltage drop. An equation relating the EOF with the total voltage drop was derived and evaluated experimentally. On-line preconcentration of both positively charged and negatively charged model proteins was demonstrated without using discontinuous background electrolytes, and protein analytes were concentrated by approximately 60-200-fold under various conditions. For positively charged proteins, positive voltages of the same magnitude were applied at the free ends of the connected capillaries while the porous joint was grounded. This provided a zero EOF in the system and a non-zero local electric field in each capillary to drive the positively charged analytes to the porous joint. CE separation was then initiated by switching the polarity of the high voltage over the second capillary. For negatively charged proteins, the procedure was the same except negative voltages were applied at the free ends of the capillaries. Mobility-based selective on-line preconcentration was also demonstrated with two negatively charged proteins, i.e. beta-lactoglobulin B and myoglobin. In this case, negative voltages of different values were applied at the free ends of the capillaries with different values, which provided a non-zero EOF in the system. The direction of EOF was the same as that of the electrophoretic migration velocities of the protein analytes in the first capillary and opposite in the second capillary. By controlling the EOF, beta-lactoglobulin B, which has a higher mobility, could be concentrated over 150-fold with a 15 min injection while myoglobin, which has a lower mobility, was eliminated from the system.     

新型螯合棉分离抑制动力学光度法测定痕量铅

研究了在硼砂 氢氧化钠介质中 ,以 2 ,2′ 联吡啶为活化剂 ,Pb2 +对过氧化氢氧化偶氮氯磷 (Ⅲ )褪色反应具有的作用及其动力学条件 ,从而建立了一种测定痕量铅的新的动力学光度法 ,该方法的检出限为 3 9× 1 0 - 1 1 g/mL ,线性范围为 0～ 1 0 μg/1 0mL ,采用自制的MBM新型螯合棉纤维分离富集 ,可用于环境样品中痕量Pb2 +的测定。     

A sensitive spectrophotometric method for the determination of dithiocarbamate fungicide and its application in environmental samples

A sensitive spectrophotometric method based on the evolution of CS₂ and colour development by leuco crystal violet is described for the determination of dithiocarbamate fungicides, e.g. thiram, ziram and zineb. Dithiocarbamate fungicides release CS₂ on acid hydrolysis. This CS₂ is absorbed in ethanolic sodium hydroxide and forms xanthate. The xanthate formed is subsequently treated with potassium iodate and N-chlorosuccinimide, during which free iodine is liberated. Crystal violet dye was formed through selective oxidation of leuco crystal violet by liberated iodine, which has an absorbance maxima at 595 nm. The colour systems obey Beer's law in the range of 0.02–0.20, 0.02–0.24 and 0.04–0.32 ppm for thiram, ziram and zineb respectively. The molar absorptivity of the colour system were found to be 9.6×10⁵, 1.1×10⁶ and 6.8×10⁵±100 l mol⁻¹ cm⁻¹ for thiram, ziram and zineb respectively. The method has been successfully applied to the determination of these dithiocarbamate fungicides in various environmental samples.     

Separation and preconcentration by flow injection coupled to tungsten coil electrothermal atomic absorption spectrometry

A flow injection system coupled to a tungsten coil electrothermal atomizer has been developed for on-line separation and preconcentration, using lead as a model element. The system utilizes three-way solenoid valves for sampling, buffering, washing and reconditioning solution management, and the resin column is inserted in the tip of the autosampler arm of a Varian GTA-96. The solenoid valves and tungsten coil power supply were controlled by a computer program written in Visual Basic, interfaced with the built-in Varian software. The system performance was tested by loading the resin column with the sample flowing at 3 ml min⁻¹ for 60 s. Elution was performed automatically by sampling 20 μl of the eluent from a sample cup of the autosampler, and this aliquot was delivered into a 150 W tungsten coil. With Chelex-100 resin, the separation of concomitants was tested with lead in the presence of as much as 1000 mg l⁻¹ of Ca, Mg, Na or K. The model system presented an enrichment factor of 64 at a sampling rate of 30 samples per hour.     

Application of pyridylazo and thiazolylazo reagents in flow injection preconcentration systems for determination of metals

Pyridylazo and thiazolylazo reagents are synthetic dyes widely used in analytical chemistry. These reagents are also very attractive for use in preconcentration systems. This paper covers the application of pyridylazo and thiazolylazo reagents in flow injection systems for the determination of metals. The article discusses flow injection preconcentration systems with solid-phase extraction, precipitation and cloud point extraction. The use of pyridylazo and thiazolylazo reagents in flow injection detection systems is also presented. The relative advantages and drawbacks of these systems are discussed. The application of pyridylazo and thiazolylazo reagents in new systems is presented in the concluding part of this review article.