Tetrapyrazolic tripods. Synthesis and preliminary use in metal ion extraction

The synthesis of two new tetrapyrazolic tripods with a side-arm bearing a functionalized donor-group is reported. The complexing properties of these compounds towards heavy metal ions (Hg²⁺, Cd²⁺, Pb²⁺) and alkaline metal ions (K⁺, Na⁺, Li⁺) was studied by a liquid-liquid extraction process and the extracted cation percentage was determined by atomic absorption measurements.     

Synthesis of lariat organochalcogenoethers based on azacalix[3]arenes for the potentiometric detection of [UO2] ions

The syntheses of organochalcogen-supported azacalix[3]arenes are described in a one-pot manner in satisfactory yields. A remarkably selective potentiometric response was accomplished for uranyl ions over a variety of other metal ions, including alkali (Na⁺, K⁺), alkaline-earth (Mg²⁺, Ca²⁺, Ba²⁺), transition and heavy metal ions (Co²⁺, Ni²⁺, Cu²⁺, Ag⁺, Fe³⁺, Zn²⁺, Cd²⁺ and Pb²⁺) using an ion-selective electrode based on compound 3 incorporated into a polymeric (PVC) membrane.     

Probing the interaction of alkali and transition metal ions with bradykinin and its des-arginine derivatives via matrix-assisted laser desorption/ionization and postsource decay mass spectrometry

The complexes of the peptides (Pep) bradykinin (RPPGFSPFR), des-Arg¹-bradykinin, and des-Arg⁹-bradykinin with the metal (M) ions Na⁺, K⁺, Cs⁺, Cu⁺, Ag⁺, Co²⁺, Ni²⁺, and Zn²⁺ are generated in the gas phase by matrix-assisted laser desorption/ionization and the structures of the corresponding [Pep + M⁺]⁺ or [Pep − H⁺ + M²⁺]⁺ cations are probed by postsource decay (PSD) mass spectrometry. The PSD spectra depend significantly on the metal ion attached; moreover, the various metal ions respond differently to the presence or absence of a basic arginine residue. The Na⁺ and K⁺ adducts of all three peptides mainly produce N-terminal sequence ions upon PSD; the fragments observed point out that these metal ions are anchored by the PPGF segment and not the arginine residue(s). In contrast, the adducts of Cu⁺ and Ag⁺ show a strong dependence on the position of Arg; complexes of des-Arg¹-Pep (which contains a C-terminal Arg) produce primarily y_n ions whereas those of des-Arg⁹-Pep generate exclusively a_n and b_n ions. These trends are consistent with Cu⁺ ligation by Arg’s guanidine group. The [Pep + Cs⁺]⁺ ions mainly yield Cs⁺; a second significant fragmentation occurs only if a C-terminal arginine is present and involves elimination of this arginine’s side chain plus water. This reaction is rationalized through a salt bridge mechanism. The most prominent PSD products from [Pep − H⁺ + Co²⁺]⁺ and [Pep − H⁺ + Ni²⁺]⁺ contain at least one phenylalanine residue, revealing a marked preference for these divalent metal ions to bind to aromatic rings; the fragmentation patterns of the complexes further suggest that Co²⁺ and Ni²⁺ bind to deprotonated amide nitrogens. The coordination chemistry of Zn²⁺ combines features found with the divalent Co²⁺/Ni²⁺ as well as the monovalent Cu⁺/Ag⁺ transition metal ions. Generally, the structure and fragmentation behavior of each complex reflects the intrinsic coordination preferences of the corresponding metal ion.     

Rhodamine-Appended Bipyridine: XOR and OR Logic Operations Integrated in an Example of Controlled Metal Migration

A new bipyridyl derivative 1 bearing rhodamine B as visible fluorophore was designed, synthesized and characterized as a fluorescent and colorimetric sensor for metal ions. Interaction with Cu²⁺, Zn²⁺, Cd²⁺, Hg⁺, and Hg²⁺ ions was followed by UV/Vis and emission spectroscopy. Upon addition of these metal ions, different colorimetric and fluorescent responses were observed. “Off-on-off” (Cu²⁺, Zn²⁺, and Hg²⁺) and “off-on” (Hg⁺ and Cd²⁺) systems were obtained. Probe 1 was explored to mimic XOR and OR logic operations for the simultaneous detection of Hg⁺–Cu²⁺ and Hg⁺–Zn²⁺ pairs, respectively. DFT calculations were also performed to gain insight into the lowest-energy gas-phase conformation of free receptor 1 as well as the atomistic details of the coordination modes of the various metal ions.     

Determination of orders of relative alkali metal ion affinities of crown ethers and acyclic analogs by the kinetic method

Ladders of relative alkali ion affinities of crown ethers and acyclic analogs were constructed by using the kinetic method. The adducts consisting of two different ethers bound by an alkali metal ion, (M₁ + Cat + M₂)⁺, were formed by using fast atom bombardment ionization to desorb the crown ethers and alkali metal ions, then collisionally activated to induce dissociation to (M₁ + Cat)⁺ and (M₂ + Cat)⁺ ions. Based on the relative abundances of the cationized ethers formed, orders of relative alkali ion affinities were assigned. The crown ethers showed higher affinities for specific sizes of metal ions, and this was attributed in part to the optimal spatial fit concept. Size selectivities were more pronounced for the smaller alkali metal ions such as Li⁺, Na⁺, and K⁺ than the larger ions such as Cs⁺ and Rb⁺. In general, the cyclic ethers exhibited greater alkali metal ion affinities than the corresponding acyclic analogs, although these effects were less dramatic as the size of the alkali metal ion increased.     

Ratiometric and turn-on monitoring for heavy and transition metal ions in aqueous solution with a fluorescent peptide sensor

A novel fluorescent peptide sensor containing tryptophan (donor) and dansyl fluorophore (acceptor) was synthesized for monitoring heavy and transition metal (HTM) ions on the basis of metal ion binding motif (Cys-X-X-X-Cys). The peptide probe successfully exhibited a turn on and ratiometric response for several heavy metal ions such as Hg²⁺, Cd²⁺, Pb²⁺, Zn²⁺, and Ag⁺ in aqueous solution. The enhancements of emission intensity were achieved in the presence of the HTM ions by fluorescent resonance energy transfer (FRET) and chelation enhanced fluorescence (CHEF) effects. The detection limits of the sensor for Cd²⁺, Pb²⁺, Zn²⁺, and Ag⁺ were lower than the EPA's drinking water maximum contaminant levels (MCL). We described the fluorescent enhancement, binding affinity, and detection limit of the peptide probe for HTM ions.     

A DFT Study on the Selective Extraction of Metallic Ions by 12-Crown-4

In order to predict the extraction ability of 12-crown-4 for different metallic ions, the complexes [M(12-crown-4)] and [M(H₂O)₄] (where M=Li⁺, Na⁺, K⁺, Be²⁺, Mg²⁺, Ca²⁺, Cu²⁺ and Zn²⁺) were investigated by the density functional theory without restrictions for their geometry. The metal binding capability was evaluated using the binding energy, and the effect of nature of the metal on the binding properties was also studied. The results of the calculations showed that the coordination ability of a donor molecule towards different metal ions increased in proportion to their ionization potential. In addition, based on the extraction distribution coefficient, we found that 12-crown-4 can selectively extract Cu²⁺ and Be²⁺ ions from aqueous solutions of mixed cations. Obviously, the stability of complexes and the extraction power of extractants depend greatly on the nature of the metal ions. Calculation results from our study could be used to predict the extraction power of this crown ether and could play a guiding role in planning experiments.     

Transport of metal ions through cation exchange membranes containing episulfide (or thiol) groups and/or triethylenetetramine side chains

Two types of cation exchange membranes bearing sulfonic acid groups were prepared. One membrane (EA membrane), having episulfide groups beside sulfonic acid groups, was prepared with 2,3-epithiopropylmethacrylate (ETMA)-2-acrylamide-2-methylpropane sulfonic acid (AMPS) copolymers and the another one (EA-TTA membrane) having thiol groups, triethylenetetramide (TTA) side chains, and carboxyl groups beside sulfonic acid groups was prepared by treating EA membranes with TTA in a water-1,4-dioxane mixture solution. The transport of metal ions such as K⁺, Li⁺, Ag⁺, Ca²⁺, and Cu²⁺ through the membranes was investigated. The transport rate of Ag⁺ through the EA membranes was considerably lower than those of other metal ions from solution. High selective transport of Ag⁺ from mixed solution could be observed using the EA and EA-TTA membranes. Transport of Cu²⁺ and Ca²⁺ through the EA-TTA membrane was depressed by an electrostatic repulsion between ammonium groups in the membranes and metal ions when HNO₃ or sodium ethylenediamine tetraacetate was used as receiving solution.     

Calix[4]arene-based fluorescent probe and the adsorption capacity of its electrospun nanofibrous film for the cesium cation as an adsorbent

Calix[4]arene-based cation receptor 1 has been synthesised by following a multi-step synthetic procedure. The fluorescence properties of 1 upon the addition of various metal ions were investigated by fluorescence spectroscopy. As a result, it was revealed that 1 displayed dramatic quenching effect upon the exposure to Cs⁺. In contrast, no significant quenching effects were observed upon the addition of other metal ions such as Li⁺, Na⁺, K⁺, Mg²⁺, Ca²⁺, Sr²⁺, Ag⁺, Zn²⁺ and Ni²⁺. Compound 1 was also found by Job plot to form a 1:1 complex with Cs⁺. In addition, we also prepared 1-embedded electrospun nanofibrous film (NF-1) as an adsorbent for Cs⁺. NF-1 is proved to adsorb Cs⁺ effectively from an aqueous solution, indicating that it would be usefully utilised as an adsorbent to remove Cs⁺.     

A Highly Copper‐Selective Ratiometric Fluorescent Sensor Based on BODIPY

A new ratiometric fluorescent sensor ( 1 ) for Cu²⁺ based on 4,4‐difluoro‐4‐bora‐3a,4a‐diaza‐s‐indacene (BODIPY) with di(2‐picolyl)amine (DPA) as ion recognition subunit has been synthesized and investigated in this work. The binding abilities of 1 towards different metal ions such as alkali and alkaline earth metal ions (Na⁺, K⁺, Mg²⁺, Ca²⁺) and other metal ions ( Ba²⁺, Zn²⁺, Cd²⁺, Fe²⁺, Fe³⁺, Pb²⁺, Ni²⁺, Co²⁺, Hg²⁺, Ag⁺) have been examined by UV‐vis and fluorescence spectroscopies. 1 displays high selectivity for Cu²⁺ among all test metal ions and a ～10‐fold fluorescence enhancement in I₅₈₂/I₅₅₈ upon excitation at visible excitation wavelength. The binding mode of 1 and Cu²⁺ is a 1:1 stoichiometry determined via studies of Job plot, the nonlinear fitting of the fluorometric titration and ESI mass.     

Kinetics and Determination of Some Transition Metals with Peri-Dihydroxynaphthindenone

Abstract

A simple sensitive and selective spectrophotometric method has been developed for determination of some transition metal ions. It is based on the reaction of the metal ions with excess peri-dihydroxynaphthindenone in 80% v/v ethyl alcohol-water mixture at 30°C. The colored products obtained display maximum absorption band at 560–590 nm depending upon the type of transition metal ion used, and E_{1 cm} ^1% in the range 70–480. Under the optimum conditions results with an average recovery of 96%, (mean standard deviation ±3% are obtained for 6 different transition metal ions without any significant interference from Li⁺, Na⁺, K⁺, Cs⁺, Rb⁺, Ba²⁺, Sr²⁺, Ni²⁺, Bi³⁺, Co²⁺, Mn⁺², Cd⁺² and Al⁺³. Kinetic data reveal that the reaction proceeds via a second order route (first order with respect to either the metal cation or ligand). The activation parameters and a suggested mechanism have been presented, and the nature of bonding in the solid chelate products has been verified.     

Spectrophotometric study of complexation of dibenzopyridino-18-crown-6 with some transition and post-transition metal ions in DMSO solution using murexide as a metallochromic ligand

The complexation reaction of dibenzopyridino-18-crown-6 (DBPY 18C6) with Co²⁺, Cu²⁺, Zn²⁺, Pb²⁺, Cd²⁺, Hg²⁺, and Ag⁺ have been studied in DMSO at 25°C by the spectrophotometric method. Murexide was used as a competitive colored ligand. The stoichiometry of metal ion-murexide and metal ions with DBPY18C6 complexes were estimated by mole ratio and continuous variation methods and emphasized by the KINFIT program. The stoichiometry of all the complexes was found to be 1: 1 (metal ion/ligand). The order of stability constants for the obtained metal ion-murexide complexes (1: 1) varies in the order Cu²⁺ > Cd²⁺ > Co²⁺ ∼ Pb²⁺ > Zn²⁺ > Ag⁺ > Hg²⁺. This trend shows that the transition metal ions clearly obey the Irving-Williams role. For the post-transition metal ions, the ionic radius and soft-hard behavior was the major affects in varying of this order. The dibenzopyridino-18-crown-6 complexes with the used metal ions vary as Ag⁺ > Pb²⁺ > Cu²⁺ > Cd²⁺ > Hg²⁺ > Zn²⁺ > Co²⁺. The article is published in the original.     

Synthesis, coordination properties, and analytical applications of mixed donor macrocycles containing the 1,10-phenanthroline sub-unit

The coordination properties towards different metal ions of a new class of mixed N/S-, and N/S/O-donor macrocycles containing the 1,10-phenanthroline sub-unit in the cyclic framework are reviewed. The conformational constraints imposed by the heteroaromatic fragment onto the aliphatic portion of the ring determine the coordination mode of these ligands which can stabilise low-valent Ni⁺, Pd⁺, Pt⁺, and Rh⁺ metal complexes. Structural and thermodynamic aspects of the coordination chemistry of these ligands are considered together with possible applications as building blocks in the synthesis of multi-centred systems, and as template in the construction of extended polyiodide networks. However, solution studies demonstrate the inability of these ligands to work as selective and specific fluorescent chemosensors for heavy transition and post-transition metal ions and the formation constants evaluated for the formation of 1:1 complexes with Pb²⁺, Cd²⁺, Hg²⁺, Cu²⁺, and Ag⁺ in acetonitrile are of the same order of magnitude. Nevertheless, some of these macrocyles are extremely effective to recognise Cu²⁺ or Ag⁺ over the other metal ions in transport processes, and have been successfully used as neutral ionophore in the construction of PVC-based ionselective electrodes and supported liquid membranes for analytical detection and separation, respectively, of these metal ions.     

High Sensibility of Quantum Dots to Metal Ions Inspired by Hydroxyapatite Microbeads

An approach for the sensitive and selective determination of Ag⁺, Cu²⁺ and Hg²⁺ ions was developed based on the fluorescence quenching of mercaptopropionic acid (MPA) capped CdTe quantum dots in the existence of hydroxyapatite (HAP) nanoribbon spherulites. Among various metal ions investigated, it was found that the fluorescence of CdTe QDs was only sensitive to Ag⁺, Cu²⁺ and Hg²⁺ ions. The addition of HAP into the CdTe system could bring forward a sensitivity improvement of about 1 to 2 orders of magnitude in the detection of Ag⁺ and Cu²⁺ compared with the plain CdTe system without the existence of HAP; while there was no sensitization effect for Hg²⁺. Under optimal conditions, the detection limits for Ag⁺, Cu²⁺ and Hg²⁺ were 20, 56 and 3.0 nmol·L^?1, respectively, and the linear ranges were 0.02–50, 0.056–54 and 0.003–2.4 µmol·L^?1, respectively. Mechanisms of both QDs fluorescence quenching by metal ions and the sensitization effect by HAP were also discussed.     

Lattice polarization effects in electrochromic switching in WO3−x films studied by pulse-nanogravimetric technique

The interactions of various types of cations with the tungsten trioxide lattice have been investigated to evaluate possible intercalation of these cations and the occurrence of lattice polarization leading to the near-surface structural lattice damage. The interactions of cations, such as the large monovalent cations (K⁺, Et₄N⁺, CtMe₃N⁺ cations), transition metal dications (Ni²⁺), heavy metal ions (Cd²⁺), and representative lanthanides (La³⁺) and actinides (Th⁴⁺), in competition with intercalation of H⁺ ions have been investigated using pulse-nanogravimetric technique. The effects of these cations in electrochromic processes of WO₃ proceeding during cathodic reduction have been assessed. For all of the metal ions studied, a large increase in the apparent mass uptake (up to eightfold) in comparison to pure H⁺ ion ingress was observed upon the film coloration induced by a cathodic potential pulse. The experiments indicate that the apparent mass gains, although large, are insufficient to confirm predominant contribution of metal ions in the ion transport along the channels in WO₃ lattice. The lower decoloration rate in the case of Ni²⁺ ions, in comparison to H⁺ and other transition metal cations (Cd²⁺), has been attributed to a slow dissociation of Ni²⁺ ions from lattice-bound oxygen atoms. For et₄N⁺ cation, which is too large to enter channels in WO₃, a dissociative reduction of the WO₃ and severe lattice damage was observed. Among the metal ions investigated, only K⁺ ions have been found to cause a dissociative reduction of WO₃ and near-surface lattice damage. Strong lattice polarization effects and irreversible binding have been found for La³⁺ and Th⁴⁺ cations.     

New generation of functionalized bipyrazolic tripods: synthesis and study of their coordination properties towards metal cations

A simple and easily synthesis of new generation of N-donor bipyrazolic tripods by coupling of functionalized pyrazole derivatives and an appropriate primary amine derivative via condensation or nucleophilic substitution reaction is presented. The complexation capacity of these compounds towards bivalent metal ions (Hg²⁺, Cu²⁺, Pb²⁺, Cd²⁺) and alkaline metal ions (Li⁺, Na⁺, K⁺) were investigated using the liquid–liquid extraction process. The percentage limits of extraction were determined by atomic absorption measurements.     

Synthesis, characterization and analytical application of a new inorganic cation exchanger—Titanium(IV) molybdophosphate

A novel polyoxometalate-cation exchanger, titanium(IV) molybdophosphate (TMP) has been synthesized under varying conditions. The material was characterized by X-ray diffraction, infrared spectroscopy, inductively coupled plasma and thermogravimetry techniques. Its stability was investigated in water, dilute acids, alkaline solutions, and high temperature up to 750 °C. Ion-exchange capacity and distribution coefficients (K_d) for twenty-nine radionuclides and metal ions have been determined. It was found that the TMP has high affinity for Cs⁺, Sr²⁺, UO₂²⁺, Ba²⁺, Pb²⁺, Tl⁺, Zn²⁺, Rb²⁺ and Zr⁴⁺ ions. The results of binary separation of metal ions showed that TMP can be potentially useful for analytical applications.     

Highly selective fluorescent recognition of Zn2+ based on naphthalene macrocyclic derivative

A new macrocyclic chemosensor containing two naphthalene fluorophores has been synthesized. The fluorescent properties of this receptor has been studied in the presence of various metal ions such as Na⁺, Ag⁺, Cr³⁺, Mn²⁺, Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺ and Pb²⁺. When increasing concentrations of Zn²⁺ ions were introduced, the emission of L was drastically increased (EFE = 4.34). This special change was not observed when other metal ions were used; such highly selective fluorescent response indicates that this receptor can easily discriminate Zn²⁺ ions from other similar species. Model calculations at DFT level further suggest the possible interaction mode, and relatively steric position between the host and guest also influence the optical response.     

Stability of transition metal complexes with sulfonated polymers

Stability constants of macromolecular metallocomplexes of transition metal ions (Ag⁺, Cu²⁺, Ni²⁺, Fe³⁺) with sulfonated polymers in water and aqueous HCl and NaCl solutions were determined from quenching by transition metal ions of the luminescence of macromolecules labeled with luminescent groups.