Ultratrace determination of mercury in water following EN and EPA standards using atomic fluorescence spectrometry

Chemical vapour generation has been used in combination with atomic fluorescence spectrometry to determine mercury at ultratrace concentrations down to 0.1 ng L^–1. A time-based injection of 1 mL of solution for measurement was sufficient to generate a steady-state detector response in the direct mode of measurement. The detection limit calculated from a ten-point calibration curve according to DIN 32645 was 0.26 ng L^–1. Instrument noise is limited by reflected radiation from the light source rather than by the dark current of the photomultiplier. The detection limit is directly influenced by the reagent blank which was 2 ng L^–1 in the experiments described. Focusing by amalgamation and subsequent thermal desorption generates a detector response which is about eight times higher in peak intensity and about twice as large in integrated intensity. The detection limit under these conditions is 0.09 ng L^–1 which can be further improved by preconcentration of larger volumes of solution for measurement. The cycle time for one individual reading is about 40 s without amalgamation and 125 s with amalgamation. The linear dynamic range of the system is five orders of magnitude with a single photomultiplier gain setting. The carry-over is less than 0.3% in direct measurement mode. Reference water samples and a surface water containing approximately 5 ng L^–1 were used to prove the validity of the method for real samples. Good accuracy and recoveries of 103% were calculated using the fast direct determination technique.     

电化学冷蒸气发生-原子荧光光谱法测定人发中的痕量汞

采用自制的电化学流通池作为汞蒸气发生器,以玻碳为阴极材料,结合原子荧光光谱法,在断续流动条件下,建立了电化学冷蒸气发生法-原子荧光光谱联用技术(ECVG-AFS)对汞的分析方法.在优化的实验条件下,汞在0～5.0μg/L范围内荧光强度与浓度呈良好的线性关系,汞的检出限为1.2 ng/L.对1μg/L Hg测定的相对标准偏差为1.8%(n=11).可用于人发标准样品中汞的测定.     

Determination of mercury by intermittent flow electrochemical cold vapor generation coupled to atomic fluorescence spectrometry

A novel method for determination of mercury was developed using an intermittent flow electrochemical cold vapor generation coupled to atomic fluorescence spectrometry (IF-ECVG-AFS). The mercury vapor was generated on the surface of glassy carbon cathode in the flow cell. The operating conditions for the electrochemical generation of mercury vapor were investigated in detail, and the interferences from various ions were evaluated. Under the optimized conditions, no evident memory effects of mercury were observed. The calibration curve was linear up to 5 μg L⁻¹ Hg at 0.54 A cm⁻². A detection limit of 1.2 ng L⁻¹ Hg and a relative standard deviation of 1.8% for 1 μg L⁻¹ Hg were obtained. The accuracy of method was verified by the determination of mercury in the certified reference human hair. The ECVG avoided the use of reductants, thereby greatly reducing the contamination sources. In addition, the manifold of IF-ECVG-AFS was simple and amenable to automation.     

分散固液微萃取在线热洗脱原子荧光法测定矿泉水中的痕量汞

研究制备了CI/SiO2/PDMS固相萃取剂,建立了分散固液微萃取在线热洗脱原子荧光联用测定矿泉水中痕量汞的方法。方法使用分散剂将CI/SiO2/PDMS均匀分散于样品溶液中,吸附并富集Hg2+与DDTC形成的Hg-DDTC螯合物。用磁子吸附收集固相萃取剂,并置于石英管中。利用电磁感应加热技术,在线加热洗脱,原子荧光法定量。方法的富集倍数达30倍,检出限为6.0ng/L;精密度RSD为3.8%(n=11,ρ=0.1μg/L)。     

Determination of mercury by electrochemical cold vapor generation atomic fluorescence spectrometry using polyaniline modified graphite electrode as cathode

An electrochemical cold vapor generation system with polyaniline modified graphite electrode as cathode material was developed for Hg (II) determination by coupling with atomic fluorescence spectrometry. This electrochemical cold vapor generation system with polyaniline/graphite electrode exhibited higher sensitivity; excellent stability and lower memory effect compared with graphite electrode electrochemical cold vapor generation system. The relative standard deviation was 2.7% for eleven consecutive measurements of 2 ng mL^− 1 Hg (II) standard solution and the mercury limit of detection for the sample blank solution was 1.3 рg mL^− 1 (3σ). The accuracy of the method was evaluated through analysis of the reference materials GBW09101 (Human hair) and GBW 08517 (Laminaria Japonica Aresch) and the proposed method was successfully applied to the analysis of human hairs.     

原子荧光光谱法测定蛇粉中汞的方法研究

用微波消解仪消解、氢化物发生-原子荧光光谱法测定蛇粉中的微量Hg,优化了仪器的工作条件。测定汞的检出限为0.7pg/mL。测定0.3及1ng/L Hg标准溶液,相对标准偏差分别为4.1%及0.9%,加标回收率为87%~110%。     

Direct determination of mercury in white vinegar by matrix assisted photochemical vapor generation atomic fluorescence spectrometry detection

This paper proposes the use of photochemical vapor generation with acetic acid as sample introduction for the direct determination of ultra-trace mercury in white vinegars by atomic fluorescence spectrometry. Under ultraviolet irradiation, the sample matrix (acetic acid) can reduce mercury ion to atomic mercury Hg⁰, which is swept by argon gas into an atomic fluorescence spectrometer for subsequent analytical measurements. The effects of several factors such as the concentration of acetic acid, irradiation time, the flow rate of the carrier gas and matrix effects were discussed and optimized to give detection limits of 0.08 ng mL⁻¹ for mercury. Using the experimental conditions established during the optimization (3% v/v acetic acid, 30 s irradiation time and 20 W mercury lamp), the precision levels, expressed as relative standard deviation, were 4.6% (one day) and 7.8% (inter-day) for mercury (n = 9). Addition/recovery tests for evaluation of the accuracy were in the range of 92–98% for mercury. The method was also validated by analysis of vinegar samples without detectable amount of Hg spiked with aqueous standard reference materials (GBW(E) 080392 and GBW(E) 080393). The results were also compared with those obtained by acid digestion procedure and determination of mercury by ICP-MS. There was no significant difference between the results obtained by the two methods based on a t-test (at 95% confidence level).     

Analytical approach for routine methylmercury determination in seafood using gas chromatography-atomic fluorescence spectrometry

Two methodologies have been developed for the analysis of mercury species in seafood by capillary gas chromatography coupled to an AFS detector via pyrolysis. The first one is based on the ethylation of both, inorganic and methylmercury species (Method 1), in which clean-up is not necessary because a small amount of sample is required. In the second one, monoalkylated mercury species are extracted into organic phases after forming the corresponding chlorides (Method 2). In this case the elimination of the interfering compounds from the matrix requires a clean-up step, which enables the treatment of higher quantities of sample. Both procedures can be considered complementary because the concentration range applicable for each one of them is different: 0.75-10 μg_Hg g⁻¹, in dry basis for methylmercury (Method 1) and 6-1000 ng_Hg g⁻¹ (Method 2). The range of application for natural samples can be easily selected by a preliminary analysis of total mercury, because most mercury in seafood is present as MeHg. Optimum parameters for both procedures have been evaluated, and the methods were validated with two standard reference materials (BCR-463 and NIST-2977). Finally, the methods have been applied to the analysis of seafood samples. Detection limits of MeHg range from 1.7 to 220 ng_Hg g⁻¹ (dry basis) depending of the methodology selected and the weight of sample. The method can be successfully applied to commercially available seafood samples, and considered for routine analysis.     

Determination of mercury and methylmercury in seafood by ion chromatography using photo-induced chemical vapor generation atomic fluorescence spectrometric detection

A novel method based on photo-induced chemical vapor generation (CVG) as interface to on-line coupled Hg-cysteine ion chromatograpy (IC) with atomic fluorescence spectrometry (AFS) was developed for rapid determination of methylmercury (MHg) in seafood. Separation of inorganic mercury (Hg²⁺) and methylmercury(CH₃Hg⁺) was accomplished on a Hamilton PRP X-200 polymer-based exchange column with a mobile of 3% acetonitrile, 1% (w/w) L-cysteine and 20 mmol L^{− 1} pyridine and 160 mmol L^{− 1} formic acid, at pH 2.4 within 7 min. Once separated, both species are reduced by formic acid in mobile phase under UV radiation to convert Hg⁰ on-line, which is subsequently swept (by argon carrier gas) into an atomic fluorescence spectrometry (AFS) for measurement. Under the optimized experiment conditions, the detection limits (as Hg), based on three times the standard deviation of a standard solution, were found to be 0.1 ng mL^{− 1} for mercury and 0.08 ng mL^{− 1} for methylmercury, with an injection volume of 100 μL. The developed method was validated by determination of certified reference material DORM-2 and was further applied in determination of seafood samples.     

聚苯胺修饰电极-电化学氢化物发生原子荧光光谱法测定食品中锡含量

运用以聚苯胺修饰的石墨电极为阴极的电化学氢化物发生装置实现了锡元素的电化学氢化物发生.在电极表面聚合一层聚苯胺,能够有效地提高锡元素的电化学氢化物发生效率,通过与原子荧光光谱仪联用,成功地测定了食品中的锡含量.本工作对各种实验参数和干扰情况进行了详细研究.方法对锡的检出限为1.2 ng/mL(3σ)；样品分析精密度(R...     

Cold vapor generation interface for mercury speciation coupling capillary electrophoresis with electrothermal quartz tube furnace atomic absorption spectrometry: Determination of mercury and methylmercury

A novel on-line coupled capillary electrophoresis (CE) cold vapor generation (CVG) with electrothermal quartz tube furnace atomic absorption spectrometry (EQTF-AAS) system for mercury speciation has been developed. The mercury species (inorganic mercury and methylmercury) were completely separated by CE in a 80 cm length × 100 μm i.d. fused-silica capillary at 20 kV and using a buffer of 100 mM boric acid and 10% (v/v) methanol (pH 8.30). The effects of the inner diameter of quartz tube, the acidity of HCl, the NaBH₄ concentration and N₂ flow rate on Hg signal intensity were investigated. Speciation of mercury was highlighted using CE-CVG-EQTF-AAS. The detection limits of methylmercury and mercury were 0.035 and 0.027 μg mL⁻¹, respectively. The precisions (RSDs) of peak height for six replicate injections of a mixture of 10 μg mL⁻¹ (as Hg) were better than 4%. The interface was used for speciation analysis of mercury in dry goldfish muscle.     

Liquid chromatographic--cold vapour atomic fluorescence spectrometric determination of mercury species

Solvent extraction, sonication, and microwave-assisted extractions in the presence of extraction agents (thioacetic acid, citric acid, cysteine, 2-mercaptoethanol, HCl + NaCl, etc.) were tested for the isolation of mercury species. A mixture of 6 M HCl and 0.1 M NaCl was selected as the most suitable extraction agent. The extraction efficiency was about 10% higher and the RSD below 3.3% when microwave-assisted extraction was applied instead of sonication. The liquid chromatography-cold vapour atomic fluorescence spectrometry (LC/CV-AFS) method was optimised and used for separation and determination of inorganic mercury cations and alkylated and arylated mercury species. Isocratic elution at a flow rate of 0.15 mL/min (with a mobile phase containing 0.05% 2-mercaptoethanol (pH = 5) and 7% methanol and with a stepwise increase of methanol content up to 100% MeOH in the 15th min) was used for separation of mercury species on a Hypersil BDS C18 RP column. The limits of detection of the LC/CV-AFS system were estimated as 0.2 microg/L (3%) for MeHg+, 0.07 microg/L (5.3%) for inorganic Hg, 0.06 microg/L (3.4%) for PhHg+, and 0.12 microg/L (4.4%) for EtHg with the corresponding RSDs at 5 microg/L (n = 10) given in parentheses. The concentrations (2-10 mg/kg fresh weight) of total mercury and methylmercury (90-99% of the total mercury) in selected fish obtained by HPLC/CV-AFS were in good agreement (absolute deviations 0.05 mg/kg) but more precise (RSDs <5.4% at 5 mg/L, n = 10) than those determined by GC coupled to an electron capture detector. The RSDs (3.1-8.2% and 4.1-9.0%) of the overall analytical procedure for the determination of total mercury (AMA 254) and methylmercury (HPLC/CV-AFS) were determined for intra-day and inter-day assays, respectively.     

Atomic fluorescence spectrometry combined with reduction aeration for the determination of mercury in biological samples

A sensitive atomic fluorescence system for the determination of mercury was optimized. The system consists of a continuous-flow mercury vapour generator coupled to a fluorescence spectrometer specific for mercury. A new gas-liquid separator was developed. A detection limit of 0.9 ng Hg 1^?1 was obtained. The system was combined with a microwave oven for dissolving samples in closed Teflon PFA vessels. Accurate results were obtained for certified reference materials, and biological samples such as urine and hair were analysed.     

Evaluation of atomic fluorescence spectrometry as a sensitive detection technique for arsenic speciation

The potential of coupling anion-exchange high-performance liquid chromatography, hydride generation and atomic fluorescence spectrometry (HPLC–HG–AFS) for arsenic speciation is considered. The effects of hydrochloric acid and sodium tetrahydroborate concentrations on signal-to-background ratio, as well as argon and hydrogen flow rates, were investigated. Detection limits for arsenite, dimethylarsinic acid (DMA), monomethylarsonic acid (MMA) and arsenate were 0.17, 0.45, 0.30 and 0.38 μg l⁻¹, respectively, using a 20-μl loop. Linearity ranges were 0.1–500 ng for As(III) and MMA (as arsenic), and 0.1–800 ng for DMA and As(V) (as arsenic). Arsenobetaine (AsB) was also determined by introducing an on-line photo-oxidation step after the chromatographic separation. In this case the limits of detection and linear ranges for the different species studied were similar to the values obtained previously for As(V). The technique was tested with a human urine reference material and a volunteer's sample. © 1998 John Wiley & Sons, Ltd.     

电解氢化物发生原子荧光法测定镉

通过电解氢化物发生技术结合原子荧光光谱仪,采用自行设计的管式电解池,研究了管状阴极材料以及电解质种类、电解条件等因素对Cd的电解还原氢化物发生情况的影响。方法检出限为0.26μg/L,相对标准偏差为3.3%(n=11)。对标准物质海带及几种海产品中的Cd进行了测定,回收率在93%～110%之间。     

Comparison of pre-reducing agents for antimony determination by hydride generation atomic fluorescence spectrometry

A systematic study of antimony reduction prior to its determination by hydride generation atomic fluorescence spectrometry (HG-AFS) was carried out. The efficiency of l-cysteine, potassium iodide and potassium iodide/ascorbic acid was studied for this purpose. The hydride generation step was optimised in the presence of those pre-reductors. From the results, l-cysteine was found to be the most suitable pre-reducing agent. Methodology was validated, obtaining detection limits lower than 90 ng l⁻¹ and repeatability and reproducibility better than 3% R.S.D. and 5% R.S.D., respectively, in all cases. In order to evaluate the methodology developed and the influence of the matrix, recovery from waters from different sources was tested by HG-AFS and also by inductively coupled plasma mass spectrometry (ICP-MS). Accuracy was assessed by analysing three water reference materials at different antimony concentration levels. The high sensitivity of the developed methodology enables it to be applied for monitoring drinking waters according to the maximum admissible concentration of antimony established by the EU Directives.     

Ion chromatography–hydride generation‐atomic fluorescence spectrometry speciation of tellurium

The speciation of tellurium was carried out using atomic fluorescence spectrometry as an element‐specific detector in hybridization with liquid chromatography and hydride generation. Good resolution could be obtained by anion‐exchange chromatography with complexing agents, using a mobile phase with 8 mM EDTA and 2 mM potassium hydrogenphthalate. Analysis time was less than 6 min. Calibration graphs were linear between 2 and 100 µg l^?1. Detection limits were 0.6 µg l^?1 and 0.7 µg l^?1 for tellurium(VI) and tellurium(IV) respectively. The method was applied to the speciation of tellurium in drinking water and wastewater samples from different metallurgical industries. Copyright © 2005 John Wiley & Sons, Ltd.     

Determination of selenium in vegetables by hydride generation atomic fluorescence spectrometry

A digestion mixture of H₂SO₄/HNO₃/H₂O₂/HF/V₂O₅ was investigated for decomposition of plant samples and sensitive detection of selenium was achieved by hydride generation atomic fluorescence spectrometry (HG-AFS). The method was found to be accurate and reproducible, with a low detection limit (DL) (0.14 ng g⁻¹ solution). The repeatability of the determination was mostly around 10%, the reproducibility over a period of 8 months for determination of selenium in the standard reference material Trace Elements in Spinach Leaves, NIST 1570a, was 9% and the relative measurement uncertainty was 7% using a coverage factor of 2.3 at 95% probability. The average recovery of the whole procedure was 90%. The characteristics of this method are simple and inexpensive equipment, low consumption of chemicals and the ability to analyse many samples in a short time. The whole procedure was carried out in the same PTFE tube, and in addition only a simple cleaning procedure is needed. As a consequence of all these advantages, the described method is suitable for environmental and nutritional studies. The selenium content was determined in 44 vegetable samples from different regions of Slovenia and the contents found were in the range 0.3-77 ng g⁻¹ wet weight.     

电化学氢化物发生-原子荧光法测定环境样品中的Se(Ⅳ)和Se(Ⅵ)

设计了一种新的电化学氢化物发生装置, 用于测定不同价态的硒. 通过对传统的平板电解池的改进, 设计了全新的圆盘电解池并采用螺纹密封的方式, 极大地缩短了电解池的装配时间, 提高了电解池的使用寿命和密封性能. 结合热水浴在线还原技术, 将 Se(Ⅵ)在高浓度HCl介质中120 s内还原成Se(Ⅳ), 通过电化学氢化物发生技术生成氢化物, 成功的进行硒的在线价态分析. 对各种实验参数进行了详细的研究, Se(Ⅳ) 和Se(Ⅵ)的相对标准偏差分别为2.6% 和 3.1% (n=11);Se(Ⅳ)和总硒的检出限分别为0.32和0.27 μg/L (3σ).     

原子荧光光谱技术在我国发展及标准化应用现状

简单介绍了原子荧光光谱技术的建立及其在国内的发展历程,重点介绍了蒸气发生-原子荧光光谱(VG-AFS)仪在我国的技术研究、仪器研制及应用;详细总结了蒸气发生-原子荧光光谱(VG-AFS)法在我国标准化方面的研究.我国在多通道原子荧光光谱仪、原子荧光形态分析仪等关键技术及其应用等方面取得了开创性的研究成果,并形成了一系列...