Detection of volatile organic sulfur compounds in water by headspace gas chromatography and membrane inlet mass spectrometry

Two gas chromatographic methods, GC-FID (flame ionization detection) and GC-ELCD (electrolytic conductivity detector) are compared in tlie analysis of volatile organic sulfur compounds (VOSCs) in water samples with a membrane inlet mass spectrometry (MIMS) technique. Carbon disulfide, ethanethiol, dimethyl sulfide, ethyl-methyl sulfide, thiophene, and dimethyl disulfide were used as test compounds. Linear dynamic ranges were found to be two decades with the GC-ELCD method and four decades with the GC-FID and MIMS methods. Detection limits were at low (μg/1 levels with the two gas chromatographic methods and clearly below μg/1 level with the MIMS method. Analysis of one sample takes 40 min with the gas chromatographic methods and five minutes with the MIMS method. The selectivity was good, especially with the GC-ELCD and the MIMS method. In addition, quantitative results obtained with spiked water samples by the three methods are compared.     

Development of a static headspace gas chromatographic/mass spectrometric method to analyze the level of volatile contaminants biodegradation

Volatile compound biodegradation analysis usually requires the time-consuming step of extraction of the analytes from the matrix using organic solvents or costly radioactive-compounds. Thus, it is desirable to have a simple and fast technique to generate a good evaluation of bacterial biodegradation. The goal of this research was to develop a methodology on the basis of static headspace-gas chromatography/mass spectrometry (HS-GC/MS) to evaluate the level of volatile contaminant biodegradation. The effects of the following parameters were studied: temperature and time of equilibration. The biodegradation experiments were carried out with bacteria inoculation in mineral media in presence of volatile hydrocarbon compounds (toluene, p-xylene, nonane and naphthalene). Autoclaved inoculates were used as control and reference sample. The optimal headspace conditions were observed when the vials were heated at 80 degrees C for 20 min, the syringe at 81 degrees C and an injection volume of 0.4 mL was used. This methodology has the advantage of being relative free from matrix effects.     

Determination of odour-causing volatile organic compounds in cork stoppers by multiple headspace solid-phase microextraction

Multiple headspace solid-phase microextraction (MHS-SPME) coupled with gas chromatography-mass spectrometry has been applied in order to determine 2,4,6-trichloroanisole (2,4,6-TCA), guaiacol, 1-octen-3-ol and 1-octen-3-one in three samples of cork stoppers. These compounds are responsible for cork taint in wine and can modify the organoleptic properties of bottled wine. Variables such as temperature, addition of water, extraction time, and amount of cork were studied. The extractions were performed with a 50/30 microm divinylbenzene-carboxen-polydimethylsiloxane (DVB-CAR-PDMS) fibre for 45 min at 100 degrees C using 20 mg of cork. For calibration, 50 microL of VOC aqueous solutions were used and the extraction were carried out for 45 min at 75 degrees C. The limits of detection of the method expressed as ng of VOC per g of cork were 0.3 for 2,4,6-TCA, 7.5 for guaiacol, 1.7 for 1-octen-3-one and 1.9 for 1-octen-3-ol. Relative standard deviation of replicate samples was less than 10%. Significant losses of analytes were observed when the samples were ground at room temperature. Finally, a recovery study was performed and the MHS-SPME results were validated using Soxhlet extraction results.     

Analysis of volatile organic compounds in fuel oil by headspace GC-MS

Fuel oils are mostly used in marine applications and in power plants. They are known to contain hazardous volatile organic compounds (VOCs) that are of health and environmental importance. Chlorinated compounds, phenolic compounds, styrenes, indene, dicyclopentadiene, dihydrodicyclopentadiene, cumene, benzene, toluene, ethylbenzene and xylenes are some of the VOCs that have found their way into fuel oil through various streams during bunkering operation. Chromatographic analysis of VOCs in the presence of complex matrices in fuel oil is one of the major challenges encountered when dealing with products of that nature. An analytical procedure using automated static headspace gas chromatography–mass spectrometry was developed for the analysis of these compounds in fuel oil. Styrene D8 and phenol D6 were used as internal standards for quantitation. Phenol D6 was used for the quantitation of phenolic compounds, while styrene D8 was used for the quantitation of other target analytes. The influence of headspace parameters on analyte response such as temperature, incubation time and sample amount were all investigated and optimised. Linear calibration curves were achieved for all components with determination coefficients R² > 0.995. Repeatability, limit of detection, limit of quantitation and recovery were reported. The matrix effect in fuel oil was minimised by 1:1 dilution with mineral oil. This method was successfully applied to the analysis of commercial samples.     

Determination of very volatile organic compounds in environmental water by injection of a large amount of headspace gas into a gas chromatograph

An injection method for a large amount of headspace gas which enables determination of trace amounts of very volatile organic compounds (VVOCs), dichlorodifluoromethane, chloromethane, vinyl chloride, bromomethane, chloroethane and trichlorofluoromethane in all kinds of environmental water was developed. A gas phase equilibrated with the water phase in a vial was purged with helium for a short time. The VVOCs were then introduced into a trapping tube packed with Tenax TA, which had been cooled using carbon dioxide. After trapping, the VVOCs were thermally desorbed and put into a GC–MS system for subsequent analysis. This method is applicable to various types of samples.     

Analysis of volatile aromatic compounds in gasoline-contaminated ground water samples by static headspace sampling and high speed gas chromatography

A 15 second, high speed, gas chromatographic determination has been performed on the volatile aromatic compounds in gasoline-contaminated ground water following manual, static headspace sampling. Retention time reproducibility of the seven peaks studied ranged from 0.25 to 0.67 per cent (average relative standard deviation). Excellent linear correlations were obtained for plots of either peak height or peak area against the concentration of the compounds. Comparison was made between the results obtained from the analysis of three replicate samples of gasoline-contaminated ground water by the high speed GC, by two field-portable GCs, and by a laboratorybased GC. It is worthy of note that all the high speed GC analyses required for this study were accomplished in one day.     

顶空固相微萃取-气相色谱-质谱联用分析纺织品中挥发性有机物

建立了顶空固相微萃取（HSSPME）-气相色谱（GC）-质谱（MS）联用测定纺织品中甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯5种挥发性有机物（VOCs）的分析方法。选择聚二甲基硅氧烷（PDMS）作为萃取涂层,优化了SPME的萃取条件,包括平衡时间、萃取时间、萃取温度、顶空体积、离子强度、搅拌速度、解吸温度和时间以及GC—MS仪器条件。对于甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯方法线性范围分别为0．087～870、3．32～3320、2．28～2280、0．015～150和0．050～50．0ng／g;检出限分别为0．005、0．042、0．670、0．008和0．011ng／g。实际样品加标回收率在80．1％～122％之间,RSD在0．8％～8．6％之间。方法符合纺织品中痕量VOCs的快速分析要求。     

Comprehensive two‐dimensional gas chromatography coupled with static headspace sampling to analyze volatile compounds: Application to almonds

The hyphenation of static headspace sampling with comprehensive 2D GC equipped with a modulator based on capillary flow technology and a flame ionization detector was used to separate and identify 43 representative target volatile compounds (light hydrocarbons, carbonyls, pyrazines, alcohols, furans, and benzenes) frequently detected in the roasting process of nuts. Five column combinations with differing degrees of orthogonality (one conventional and four inverted phase sets) were tested in order to obtain the best conditions for analyzing these volatile compounds. Optimization of the working conditions for each of the different column combinations was performed by means of a central composite design. The best results in terms of separation and differentiation among the different chemical groups were achieved with a combination of inverted phase columns (first dimension: highly polar, INNOWax; second dimension: mid‐polar, ZB‐35). Additionally, a reference template was developed to provide an effective and rapid analysis of the target compounds. Finally, the proposed method was successfully employed to identify volatile compounds in raw and roasted almond samples from the Spanish cultivar Largueta.     

Evaluation of a new graphitized carbon black employed in sampling volatile organic compounds

A new adsorbent, high-surface-area graphitized carbon black (HSGCB), with a surface area of 560 m²/g, superior to that of commonly traded graphitized carbons, was studied. The evaluation was performed in terms of breakthrough volumes and thermal desorption recoveries of substances representative of the main classes of organic compounds. HSGCB was found to be an interesting alternative to activated charcoal for volatile compounds in that it can be used in thermal desorption.     

Development and validation of a solid-phase microextraction method for the analysis of volatile organic compounds in groundwater samples

Summary Solid-phase microextraction is a relatively recent extraction technique for sample preparation. It has been used successfully to analyse environmental pollutants in a variety of matrices such as soils, water and air. In this work, a simple and rapid method for the analysis of volatile organic and polar compounds from polluted groundwater samples by SPME coupled with gas chromatography (GC) is described. Different types of fibres were studied and the extraction process was optimised. The fibre that proved to be the best to analyse this kind of samples was CAR-PDMS. The method was validated by analysis of synthetic samples and comparison with headspace—GC. The optimised method was successfully applied to the analysis of ground-water samples.     

Sampling and analysis of volatile organic compounds in bovine breath by solid-phase microextraction and gas chromatography-mass spectrometry

A relatively noninvasive method consisting of a face mask sampling device, solid-phase microextraction (SPME) fibers, and a gas chromatography-mass spectrometry (GC-MS) for the identification of volatile organic compounds (VOCs) in bovine breath was developed. Breath of three morbid steers with respiratory tract infections and three healthy steers were sampled seven times in 19 days for 15 min at each sampling. The breath VOCs adsorbed on the divinylbenzene (DVB)-Carboxen-polydimethyl siloxane (PDMS) 50/30 microm SPME fibers were transported to a laboratory GC-MS system for separation and identification with an in-house spectral library of standard chemicals. A total of 21 VOCs were detected, many of them for the first time in cattle breath. Statistical analyses using Chi-square test on the frequency of detection of each VOC in each group was performed. The presence of acetaldehyde (P < or = 0.05) and decanal (P < or = 0.10) were associated more with clinically morbid steers while methyl acetate, heptane, octanal, 2,3-butadione, hexanoic acid, and phenol were associated with healthy steers at P < or = 0.10. The results suggest that noninvasive heath screening using breath analyses could become a useful diagnostic tool for animals and humans.     

Determination of residual solvent in pharmaceutical preparations by static headspace GC

Static headspace GC, a simple, clean technique which is easily automated, appears to be a good approach to the determination of solvent residues in pharmaceutical preparations. The feasibility of this approach has been studied with an automated system. Data is presented for the solvents designated as impurities in pharmaceutical preparations by the United States Pharmacopeia. It was found that the static headspace technique meets the United States Pharmacopeia criteria for sensitivity. The absolute area count precision was <5% relative standard deviation and correlation coefficients to a linear response were >0.999. It was concluded that the technique is viable for this application.     

Determination of volatile halogenated organic compounds in soils by purge-and-trap capillary gas chromatography with atomic emission detection

Nine volatile halogenated organic compounds (VHOCs), including four trihalomethanes (THMs), were determined in soils by capillary gas chromatography with microwave induced-plasma atomic emission spectrometry (GC-AED), using a purge-and-trap system (PT) for sample preconcentration. Analytes were previously extracted from the soil sample in methanol and the extract was preconcentrated before being chromatographed. Element-specific detection and quantification were carried out monitoring two wavelength emission lines, corresponding to chlorine (479 nm) and bromine (478 nm). Each chromatographic run took 21 min, including the purge step. The method showed a precision of 1.1-7.2% (R.S.D.) depending on the compound. Detection limits ranged from 0.05 to 0.55 ng ml⁻¹, for chloroform and dichloromethane, respectively, corresponding to 3.3 and 36.0 ng g⁻¹ in the soil samples. The chromatographic profiles obtained showed no interference from co-extracted compounds. Low levels of dichloromethane and chloroform ranging from 0.04 to 1.13 μg g⁻¹ were found in samples obtained from small gardens irrigated with tap water. The method is reliable and can be used for routine monitoring in soil samples.     

新型水蒸气顶空富集装置在饮用水中痕量挥发性有机物非目标筛查中的应用

以饮用水中痕量挥发性有机物(VOCs)非目标筛查为目的,构建了一种新型的大体积水样高倍富集装置。对其精馏管长度、回收冷凝液体积、吸收介质等影响富集效果的关键因素进行了优化。该装置以水蒸气为吹扫气,同时以水作为吸收剂,将1 L水样富集浓缩至5 mL后,可使原有吹扫捕集-气相色谱-质谱法(P&;T-GC-MS)分析VOCs的灵敏度提高1～2个数量级。用该方法对某净水厂的源水与出厂水进行了痕量VOCs的定性分析与比较。与传统P&;T-GC-MS方法相比,本方法对两种水样的污染物检出数目由原来的无检出和5种分别提高至16种和35种。分析结果表明饮用水消毒前后污染物的种类及含量存在显著差异。     

Cooled internal reflection element for infrared chemical sensing of volatile to semi-volatile organic compounds in the headspace of aqueous solutions

In this study, the cooling effect was applied to an evanescent wave type infrared (IR) chemical sensing method to effectively trap volatile organic compounds (VOCs), which have been absorbed in the hydrophobic film coated around the internal reflection element (IRE). The detection of VOCs in aqueous solutions was taken in the headspace of the aqueous solution. This method eliminates the long-term instability of hydrophobic film soaked in an aqueous solution and the potential spectral interference caused by the matrix of the aqueous solution. Thermal energy has been applied to the aqueous solution to assist in the evaporation of VOCs out of the aqueous matrix. By applying a cooling system to the IRE, the excess thermal energy can be removed leading to more stable IR signals. After examination of organic compounds with vapour pressure (P_v) ranging from 0.017 to 150 Torr, significant differences were found between IR signals from cooled and un-cooled systems. Because the thermal conductivity of the IRE used in IR detection is typically low; the efficiency in removing the thermal energy is limited. By heating the aqueous solutions to different temperatures, the IR signals showed that the sample temperature was limited to around 80 °C. The IR signal determination results for five different volatility organic compounds indicated that the optimal heating temperature was not necessary to match with the volatilities of organic compounds in cooling system. The linear regression coefficient (R²) of the standard curve for sample concentrations in the range 5-200 μg ml⁻¹ was generally higher than 0.991 and the detection limit was around a few hundred ng ml⁻¹, which was two to three times lower than that of un-cooled system.     

顶空气相色谱-质谱法测定玩具中的10种挥发性有机物

建立了检测玩具中10种挥发性有机物(VOC)残留量的顶空气相色谱-质谱(HS-GC-MS)方法。样品经140 ℃、45 min静态顶空后,通过DB-624色谱柱分离和质谱检测,外标法定量。该方法对于不同VOC的定量限(LOQ)均在0.66 mg/kg以下,线性范围为0.001～2.0 μg,平均回收率在79%～106%之间,相对标准偏差(RSD)在0.4%～5.6%之间。该方法具有准确灵敏、简单快速等特点,将其应用于实际玩具样品的检测取得了良好效果。     

Improvement of HS-SPME for analysis of volatile organic compounds (VOC) in water samples by simultaneous direct fiber cooling and freezing of analyte solution

The sensitivity and precision of headspace solid-phase micro extraction (HS-SPME) at an analyte solution temperature (T _as) of +35 °C and a fiber temperature (T _fiber) of +5 °C were compared with those for HS-SPME at T _as and T _fiber of −20 °C for analysis of the volatile organic compounds benzene, 1,1,1-trichloroethane, trichloroethylene, toluene, o-xylene, ethylbenzene, m/p-xylene, and tetrachloroethylene in water samples. The effect of simultaneous fiber cooling and analyte solution freezing during extraction was studied. The compounds are of different hydrophobicity, with octanol/water partition coefficients (Kow) ranging from 126 and 2511. During a first set of experiments the polydimethylsiloxane (PDMS) SPME fiber was cooled to +5 °C with simultaneous heating of the aqueous analyte solution to +35 °C. During a second set of experiments, both SPME fiber holder and samples were placed in a deep freezer maintained at −20 °C for a total extraction time of 30 min. After approximately 2 min the analyte solution in the vial began to freeze from the side inwards and from the bottom upwards. After approximately 30 min the solution was completely frozen. Analysis of VOC was performed by coupling HS-SPME to gas chromatography-mass spectrometry (GC-MS). In general, i.e. except for tetrachloroethylene, the sensitivity of HS-SPME increased with increasing compound hydrophobicity at both analyte solution and fiber temperatures. At T _as of +35 °C and T _fiber of +5 °C detection limits of HS-SPME were 0.5 μg L⁻¹ for benzene, 1,1,1-trichloroethane, trichloroethylene, and tetrachloroethylene, 0.125 μg L⁻¹ for toluene, and 0.025 μg L⁻¹ for ethylbenzene, m/p-xylene, and o-xylene. In the experiments with T _as and T _fiber of −20 °C, detection limits were reduced for compounds of low hydrophobicity (Kow<501), for example benzene, toluene, 1,1,1-trichloroethane, and trichloroethylene. In the concentration range 0.5–62.5 μg L⁻¹, the sensitivity of HS-SPME was enhanced by a factor of approximately two for all compounds by performing the extraction at −20 °C. A possible explanation is that freezing of the water sample results in higher concentration of the target compounds in the residual liquid phase and gas phase (freezing-out), combined with enhanced adsorption of the compounds by the cooled fiber. The precision of HS-SPME, expressed as the relative standard deviation and the linearity of the regression lines, is increased for more hydrophobic compounds (Kow>501) by simultaneous direct fiber cooling and freezing of analyte solution. Background contamination during analysis is reduced significantly by avoiding the use of organic solvents.     

Determination of volatile chlorinated hydrocarbons in water samples by static headspace gas chromatography with electron capture detection

A simple, efficient, solvent‐free, and commercial readily available approach for determination of five volatile chlorinated hydrocarbons in water samples using the static headspace sampling and gas chromatography with electron capture detection has been described. The proposed static headspace sampling method was initially optimized and the optimum experimental conditions found were 10 mL water sample containing 20% w/v sodium chloride placed in a 20 mL vial and stirred at 50ºC for 20 min. The linearity of the method was in the range of 1.2–240 μg/L for dichloromethane, 0.2–40 μg/L for trichloromethane, 0.005–1 μg/L for perchloromethane, 0.025–5 μg/L for trichloroethylene, and 0.01–2 μg/L for perchloroethylene, with coefficients of determination ranging between 0.9979 and 0.9990. The limits of detection were in the low μg/L level, ranging between 0.001 and 0.3 μg/L. The relative recoveries of spiked five volatile chlorinated hydrocarbons with external calibration method at different concentration levels in pure, tap, sea water of Jiaojiang Estuary, and sea water of waters of Xiaomendao were in the range of 91–116, 96–105, 86–112, and 80–111%, respectively, and with relative standard deviations of 1.9–3.6, 2.3–3.5, 1.5–2.7, and 2.3–3.7% (n = 5), respectively. The performance of the proposed method was compared with traditional liquid–liquid extraction on the real water samples (i.e., pure, tap, and sea water, etc.) and comparable efficiencies were obtained. It is concluded that this method can be successfully applied for the determination of volatile chlorinated hydrocarbons in different water samples.     

The performance of various capillary columns for the analysis of volatile flavor compounds in dairy products by dynamic headspace gas chromatography

The aim of this study was to test the suitability and performance of various stationary phases and column dimensions for dynamic headspace gas chromatography of food aromas. The trials were performed using an aqueous test mixture containing thirty seven volatile flavor components of intense aroma, and a sample of ripe Swiss Emmental cheese. The best performance with both samples was obtained with a capillary column coated with a thick film of polydimethylsiloxane. This column resolved the greatest number of compounds in the cheese sample and resulted in the overlapping of one pair of peaks only from the test mixture. Because of its other advantages, i. e. high capacity owing to its film thickness, and insensitivity to the high moisture content of some samples or traces of oxygen in the carrier gas, the polydimethylsiloxane column appears suitable for the analysis of the volatile and highly polar compounds present in complex mixtures such as food aroma.