Sequential injection spectrophotometric determination of ritodrine hydrochloride using 4-aminoantipyrine

A sequential injection spectrophotometric determination of ritodrine hydrochloride is described. The method is based on the condensation of aminoantipyrine with phenols in the presence of an alkaline oxidizing agent to yield a pink coloured product the absorbance of which is monitored at 503 nm. Different sequential injection analysis (SIA) parameters including reagent concentrations have been optimised and used to obtain the analytical figures of merit. A linear concentration range of 3.1-123.5 μmol L⁻¹ and a detection limit (as 3σ-value) of 1.0 μmol L⁻¹ were obtained. The precision was 2.4 and 2.3% relative standard deviation (R.S.D.) at 6.2 and 15.4 μmol L⁻¹, respectively. This method is superior over previously reported ones in terms of linear range, short analysis time, high sample throughput, excellent reagent economy and minimum waste generation.     

Sequential injection chromatographic determination of ambroxol hydrochloride and doxycycline in pharmaceutical preparations

A new separation method based on a novel reversed-phase sequential injection chromatography (SIC) technique was used for simultaneous determination of ambroxol hydrochloride and doxycycline in pharmaceutical preparations in this contribution.The coupling of short monolith with SIA system results in an implementation of separation step to until no-separation low-pressure method.A Chromolith^® Flash RP-18e, 25-4.6 mm column (Merck, Germany) and a FIAlab^® 3000 system (USA) with a six-port selection valve and 5 ml syringe were used for sequential injection chromatographic separations in our study. The mobile phase used was acetonitrile-water (20:90, v/v), pH 2.5 adjusted with 98% phosphoric acid, flow rate 0.48 ml min⁻¹, UV detection was at 213 nm.The validation parameters have shown good results: linearity of determination for both compounds including internal standard (ethylparaben) >0.999; repeatability of determination (R.S.D.) in the range 0.5-5.4% at three different concentration levels, detection limits in the range 0.5-2.0 μg ml⁻¹, and recovery from the pharmaceutical preparation in the range 99.3-99.9%. The chromatographic resolution between peak compounds was >5.0 and analysis time was <9 min under the optimal conditions. The method was found to be applicable for routine analysis of the active compounds ambroxol hydrochloride and doxycycline in various pharmaceutical preparations.     

Flow-injection determination of phenylephrine hydrochloride in pharmaceutical dosage forms with on-line solid-phase extraction and spectrophotometric detection

A flow injection method is proposed for the determination of phenylephrine hydrochloride in pharmaceutical dosage forms. The method involves the use of on-line solid-phase extraction by means of a microcolumn containing Dowex 50W X8 ion-exchange resin for the separation of the analyte prior to colour development and spectrophotometric detection in the visible region.

The influence of preconcentration flow, preconcentration pH and elution volume was studied.

The method exhibits appropriate linearity (r² = 0.9999) which was proved statistically by means of the “F”-test. When applied to commercial samples containing several active ingredients and excipients, a significant reduction of interferences was found. Accuracy, evaluated by means of the spike recovery method was in the range 99.7–100.8%, with precision (R.S.D., %) better than 1%.

In order to achieve the automation the system was controlled from a notebook computer by means of a program written in QuickBASIC language. Under these conditions, a sampling frequency of 40 samples per hour could be attained.     

流动注射光度法测定盐酸普鲁卡因

在盐酸介质中,利用盐酸普鲁卡因－亚硝酸钠－α萘胺的重氨化－偶合反应,建立了流动注射光度法测定盐酸普鲁卡因的新方法。利用控制加 权形心单纯形优化法选择最佳实验条件,测定的线性范围为0－30μg/mL,该法已用于药物中盐酸普鲁卡因含量的测定。     

Simultaneous spectrophotometric and liquid chromatographic determination of dextromethorphan hydrobromide,phenylephrine hydrochloride,and carbinoxamine maleate in pharmaceutical preparations

Simultaneous determination of dextromethorphan hydrobromide (DEX), phenylephrine hydrochloride (PHEN), and carbinoxamine maleate (CAR) in pharmaceutical preparations was performed by using liquid chromatograpy (LC) and spectrophotometry. In LC, the separation was achieved on a C18 column and the optimal mobile phase for satisfactory separation in a gradient elution program was found to be acetonitrile-sodium perchlorate solution (5: 95, v/v) initially, then a linear gradient up to 60% acetonitrile in 8 min. In spectrophotometric method, a chemometric technique, principal component regression (PCR), was used. In the method, the absorbance data matrix corresponding to the concentration data matrix was obtained by the measurement of absorbances in their zero order spectra by Δλ = 1 nm in the 210–300 nm range. Then, the calibration was obtained by using this data matrix for the prediction of unknown concentrations of DEX, PHEN, and CAR in their ternary mixture. The methods proposed were validated and successfully applied to a pharmaceutical preparation, capsule, and the results were compared.     

An extractive spectrophotometric method for the determination of tetramisole hydrochloride in pharmaceutical preparations

A simple extractive photometric method for the determination of tetramisole hydrochloride in pharmaceutical preparations is described. The method uses the formation of coloured complexes of the drug with reagents such as Solochrome Dark Blue, Solochrome Black T, Bromocresol Purple, Bromothymol Blue, Bromophenol Blue and Bromocresol Green in an acidic buffer. The ion-pair complexes formed are quantitatively extracted into chloroform under the experimental conditions.     

Cost-effective flow injection spectrophotometric assay of iron content in pharmaceutical preparations using salicylate reagent

A new flow injection procedure for an assay of Fe(III) by using salicylate obtained from antipyretic powder, which is a cheap and easily available reagent, is proposed. A red complex was continuously monitored by a laboratory-made green LED colorimeter. A linear calibration was obtained in the range of 1–20 mg Fe l⁻¹ with a detection limit of 0.5 mg Fe l⁻¹ and R.S.D.s of 1.4–5.4% (n=3, for 1–20 mg Fe l⁻¹). The new procedure was applied to assay iron contents in pharmaceutical preparations. The results were in good agreement with those of the USP standard method.     

A multicommuted flow system for sequential spectrophotometric determination of hydrosoluble vitamins in pharmaceutical preparations

A multicommuted flow system is proposed for spectrophotometric determination of hydrosoluble vitamins (ascorbic acid, thiamine, riboflavine and pyridoxine) in pharmaceutical preparations. The flow manifold was designed with computer-controlled three-way solenoid valves for independent handling of sample and reagent solutions and a multi-channel spectrophotometer was employed for signal measurements. Periodic re-calibration as well as the standard addition method was implemented by using a single reference solution. Linear responses (r=0.999) were obtained for 0.500-10.0 mg l⁻¹ ascorbic acid, 2.00-50.0 mg l⁻¹ thiamine, 5.00-50.0 mg l⁻¹ riboflavine and 0.500-8.00 mg l⁻¹ pyridoxine. Detection limits were estimated as 0.08 mg l⁻¹ (0.5 μmol l⁻¹) ascorbic acid, 0.8 mg l⁻¹ (2 μmol l⁻¹) thiamine, 0.2 mg l⁻¹ (0.5 μmol l⁻¹) riboflavine and 0.1 mg l⁻¹ (0.9 μmol l⁻¹) pyridoxine at 99.7% confidence level. A mean sampling rate of 60 determinations per hour was achieved and coefficients of variation of 1% (n=20) were estimated for all species. The mean reagent consumption was 25-fold lower in relation to flow-based procedures with continuous reagent addition. Average recoveries between 95.6 and 100% were obtained for commercial pharmaceutical preparations. Results agreed with those obtained by reference methods at 95% confidence level. The flow system is suitable for application in quality control processes and in dissolution studies of vitamin tablets.     

Sequential injection method for the direct spectrophotometric determination of bismuth in pharmaceutical products

A spectrophotometric method is reported for the determination of bismuth in pharmaceutical products using sequential injection analysis. Methylthymol blue (MTB) was used as a color forming reagent and the absorbance of the Bi(III)-MTB complex was monitored at 548 nm. The various chemical and physical variables that affected the reaction were studied. A linear calibration graph was obtained in the range 0.0-75.0 mg l⁻¹ Bi(III) at a sampling frequency of 72 h⁻¹. The reagent consumption was considerably reduced compared to conventional flow injection systems, as only 150 μl of MTB were consumed per run. The precision was very satisfactory (s_r=0.5%, at 50.0 mg l⁻¹ Bi(III), n=12) and the limit of detection, c_L, was 0.250 mg l⁻¹. The developed method was applied successfully to the analysis of various pharmaceutical products containing Bi(III). The relative errors e_r, were <1.5% in all cases and were evaluated by comparison of the obtained results with those found using atomic absorption spectrometry as the reference method.     

Chemiluminescent determination of pyridoxine hydrochloride in pharmaceutical samples using flow injection

A chemiluminescent method using flow injection is described for the determination of pyridoxine hydrochloride. Its detection limit, linearity and reproducibility were examined. The method is based on the enhancing effect of pyridoxine hydrochloride on the chemiluminescence generated by the oxidation of luminol with hydrogen peroxide in aqueous potassium hydroxide and sodium oxalate. The proposed method is simple and inexpensive. The chemiluminescence intensity is a linear function of pyridoxine hydrochloride concentration over the range 10–250 μg ml⁻¹ with a detection limit of 6 μg ml⁻¹. The applicability of the method was demonstrated by the determination of pyridoxine hydrochloride in different tablet formulations and some dietary sources.     

Sequential injection technique for determination of phenoxybenzamine hydrochloride and metoclopramide in pharmaceutical formulations

A sequential injection analysis (SIA) system is described for the determination of phenoxybenzamine hydrochloride and metoclopramide using spectrophotometer as detector. The method is based on the detection of an unstable red intermediate compound resulting from the reaction of phenoxybenzamine hydrochloride or metoclopramide with the diazotizating product of p-phenylenediamine with sodium nitrite in hydrochloric acid medium. The sampling frequency is 69 h⁻¹ and 75 h⁻¹ for phenoxybenzamine hydrochloride and metoclopramide, respectively. The linear range is 10–400 μg/mL for phenoxybenzamine hydrochloride with a detection limit of 0.081 μg/mL and 20–250 μg/mL for metoclopramide with a detection limit of 0.034 μg/mL. The RSD is 1.01 and 0.45% for phenoxybenzamine hydrochloride and metoclopramide, respectively. The proposed methods were used to determine phenoxybenzamine hydrochloride and metoclopramide in pharmaceuticals. The results are compared with those obtained by pharmacopoeia method. The article is published in the original.     

Sequential optimization of a flow injection spectrophotometric method for the assay of chlorpromazine in pharmaceutical preparations

A new simple flow injection spectrophotometric method for the assay of chlorpromazine using cerium(IV) in sulfuric acid media was developed. The oxidized form of the drug was monitored at the maximum absorbance of 526 nm. The optimum conditions were 0.035M sulfuric acid, 3.80 x 10(-3)M cerium(IV), flow rate 4.85 ml/min, coil length 45 cm and sample size 110 mm(3). Optimization was carried out by the modified simplex method. Response surface methodology was employed to investigate the ruggedness of the method. A sampling frequency of 120 hr(-1) was attained. Relative standard deviations for standard sample were usually less than 0.75. The method was applied to the determination of chlorpromazine in proprietary drugs and results were statistically compared with the official British Pharmacopoeia (BP) method.     

Simultaneous determination of paracetamol,phenylephrine hydrochloride and chlorpheniramine maleate in pharmaceutical preparations using multivariate calibration 1

Resolution of binary mixtures of paracetamol, phenylephrine hydrochloride and chlorpheniramine maleate with minimum sample pre-treatment and without analyte separation has been successfully achieved by methods of partial least squares algorithm with one dependent variable, principal component regression and hybrid linear analysis. Data of analysis were obtained from UV–vis spectra of the above compounds. The method of central composite design was used in the ranges of 1–15 mg L^?1 for both calibration and validation sets. The models refinement procedure and their validation were performed by cross-validation. Figures of merit such as selectivity, sensitivity, analytical sensitivity and limit of detection were determined for all three compounds. The procedure was successfully applied to simultaneous determination of the above compounds in pharmaceutical tablets.     

A simple spectrophotometric method for the determination of nylidrin hydrochloride, isoxsuprine hydrochloride and salbutamol sulphate in pharmaceutical preparations

A simple spectrophotometric method for the determination of nylidrin hydrochloride, isoxsuprine hydrochloride and salbutamol sulphate is described, based on measurement of the orangeyellow species produced when the drugs are coupled with diazotized benzocaine (p-aminoethyl benzoate) in trimethylamine medium. The method is applicable over the range 1-12 mug ml for isoxsuprine hydrochloride and nylidrin hydrochloride and 1-8 mug ml for salbutamol sulphate. The method is a modification of the Bratton-Marshall reaction and is simple, reproducible, accurate and more sensitive than those cited in the literature.     

Sequential injection spectrophotometric determination of oxybenzone in lipsticks

A sequential injection (SI) procedure for the spectrophotometric determination of oxybenzone in lipsticks is reported. The colorimetric reaction between nickel and oxybenzone was used. SI parameters such as sample solution volume, reagent solution volume, propulsion flow rate and reaction coil length were studied. The limit of detection was 3 microg ml(-1). The sensitivity was 0.0108+/-0.0002 ml microg(-1). The relative standard deviations of the results were between 6 and 12%. The real concentrations of samples and the values obtained by HPLC were comparable. Microwave sample pre-treatment allowed the extraction of oxybenzone with ethanol, thus avoiding the use of toxic organic solvents. Ethanol was also used as carrier in the SI system. Seventy-two injections per hour can be performed, which means a sample frequency of 24 h(-1) if three replicates are measured for each sample.     

Flow injection-chemiluminescence determination of propranolol in pharmaceutical preparations

A rapid and precise continuous-flow method is described for the determination of propranolol based on the chemiluminescence (CL) produced by its reaction with potassium permanganate in a sulphuric acid medium. The optimum chemical conditions for the chemiluminescence emission were investigated. Two manifolds were tested and their characteristics such as the length of the reactor, injection volume and flow rate were compared. When using the selected manifold, propranolol gives a linear calibration graph over the concentration range 1.0-17.5 mg l⁻¹. The detection limit calculated as proposed by IUPAC was 70 ng ml⁻¹ and the detection limit calculated as proposed by Clayton was 0.87 mg l⁻¹. For analysis of 10 solutions of 10.0 mg l⁻¹ propranolol, if error propagation theory is assumed, the relative error was 0.1%. The standard deviation (S.D.) for 10 replicate samples was 0.07 mg l⁻¹. The method has been validated versus a published fluorimetric method.The present chemiluminescence procedure was applied to the determination of propranolol in simple British and Spanish pharmaceutical formulations, with excellent recoveries, as the determination is free from interference from common excipients. However, some drugs, such as hydralazine and bendroflumethizide which may also be present in the formulation, increase the emission intensity.     

Simultaneous spectrophotometric determination of fat-soluble vitamins in multivitamin pharmaceutical preparations

A spectrophotometric method is proposed for the simultaneous determination of vitamins A, D and E in multivitamin pharmaceutical preparations. This is based on multiple linear regression. Most vitamins are directly extracted from the preparations into n-hexane. Microen-capsulated vitamin A preparations require pretreatment of de-encapsulation before the vitamin is extracted. The wavelength range to be used for each preparation and the optimum spectral mode (absorbance or first-derivative) has been chosen in order to assure correct quantitation and avoid interferences from other absorbing species also extracted by n-hexane. The results obtained were validated by simultaneous HPLC analyses for accuracy and precision.     

Indirect spectrophotometric determination of benzylpenicillin and cloxacillin in pharmaceutical preparations

An indirect spectrophotometric method for the determination of benzylpenicillin and cloxacillin is based on extraction of iodine produced by reduction of potassium iodate in acidic medium, where hydrolytic cleavage of a -lactam is achieved with sodium hydroxide. Beer's law is obeyed within the concentration ranges 0.04–0.8 mg ml^–1 benzylpenicillin and 0.02–0.5 mg ml^–1 cloxacillin. The precision, accuracy of the method and the effect of foreign substances were studied. The results have been statistically compared with those using the ammonium vanadate method. An oxidation mechanism is proposed.