Headspace solvent microextraction and gas chromatographic determination of some polycyclic aromatic hydrocarbons in water samples

Headspace solvent microextraction (HSME) was shown to be an efficient preconcentration method for extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A microdrop of 1-butanol (as extracting solvent) containing biphenyl (as internal standard) was used in this investigation. Extraction occurred by suspending a 3 μl drop of 1-butanol from the tip of a microsyringe fixed above the surface of solution in a sealed vial. After extraction for a preset time, the microdrop was retracted back into the syringe and injected directly into a GC injection port. The effects of nature of extracting solvent, microdrop and sample temperatures, stirring rate, microdrop and sample volumes, ionic strength and extraction time on HSME efficiency were investigated and optimized. Finally, the enrichment factor, dynamic linear range (DLR), limit of detection (LOD) and precision of the method were evaluated by water samples spiked with PAHs. The optimized procedure was successfully applied to the extraction and determination of PAHs in different water samples.     

Residual Solvents Determination in Pharmaceuticals by Static Headspace-Gas Chromatography and Headspace Liquid-Phase Microextraction Gas Chromatography

A headspace liquid phase microextraction (HS-LPME) method has been developed and optimized for the residual solvent determination in pharmaceutical products. A microdrop of n-hexanol containing isopropanol (as internal standard) was suspended at the tip of a gas chromatographic syringe and exposed to the headspace of the sample solution. After extraction for an optimized time, the microdrop was retracted into the syringe and injected directly into a GC injection port. Critical experimental factors, including extraction solvent, temperature, ionic strength, stirring rate, extraction time, equilibrium time, drop volume, and sample volume were investigated and optimized. Compared with the static headspace technique, HS-LPME method showed superior results, being compatible with the pharmaceutical samples.     

Headspace solvent microextraction: a very rapid method for identification of volatile components of Iranian Pimpinella anisum seed

At the present study, a new and rapid headspace solvent microextraction (HSME), for the extraction and pre-concentration of the volatile components of plant sample into a microdrop was applied. The extraction occurred by suspending a microliter drop of the solvent from the tip of a microsyringe to the headspace of a ripen and powdered dry fruit sample (Iranian Pimpinella anisum seed) in a sealed vial for a preset extraction time, then the microdrop was retracted back into the microsyringe and injected directly into a GC injection port. The chemical composition of the HSME extracts were confirmed according to their retention indexes and mass spectra (EI, 70 eV); and quantitative analysis was performed by GC-FID.Parameters such as the nature of the extracting solvent, particle size of the sample, temperatures of the microdrop and sample, volume of sample and the extraction time were studied and optimized, and the method's performance was evaluated. The optimized conditions were: sample particle size, 1 mm; sample volume, 5 ml (in a 15 ml vial); sample temperature, 60 °C; microsyringe needle temperature, 0 °C; and extraction time, 10 min. Finally, accordingly, the percentage of trans-anethole (the major compound of P. anisum) and the relative standard deviation for extraction and determination of trans-anethole (seven-replicated analysis) were determined to be 90% and 3.9%, respectively.     

Hydrodistillation-headspace solvent microextraction, a new method for analysis of the essential oil components of Lavandula angustifolia Mill

A new method involving concurrent headspace solvent microextraction combined with continuous hydrodistillation (HD-HSME) for the extraction and pre-concentration of the essential oil of Lavandula angustifolia Mill. into a microdrop is developed. A microdrop of n-hexadecane containing n-heptadecane (as internal standard) extruded from the needle tip of a gas chromatographic syringe was inserted into the headspace above the plant sample. After extraction for an optimized time, the microdrop was retracted into the syringe and injected directly into a GC injection port. The effects of the type of extracting solvent, sample mass, microdrop volume and extraction time on HD-HSME efficiency were investigated and optimized. Using this method, thirty-six compounds were extracted and identified. Linalool (32.8%), linalyl acetate (17.6%), lavandulyl acetate (15.9%), alpha-terpineol (6.7%) and geranyl acetate (5.0%) were found to be the major constituents. To the best of our knowledge this is the first report on the use of continuous headspace solvent microextraction coupled with hydrodistillation for investigation of essential oil components.     

Headspace Single Drop Microextraction for the Analysis of Fire Accelerants in Fire Debris Samples

Fire accelerants such as gasoline, kerosene, and diesel have commonly been used in arson cases. Improved analytical methods involving the extraction of fire accelerants are necessary to increase sample yield and to reduce the number of uncertain findings. In this study, an analytical method based on headspace single drop microextraction (HS-SDME) followed by gas chromatography–flame ionization detection (GC-FID) has been developed for the analysis of simulated fire debris samples. Curtain fabric was used as the sample matrix. The optimized conditions were 2.5 μL benzyl alcohol microdrop exposed for 20 min to the headspace of a 10 mL aqueous sample containing accelerants placed in 15-mL sample vial and stirred at 1500 rpm. The extraction method was compared with the solvent extraction method using n-hexane for the determination of fire accelerants. The HS-SDME process is driven by the concentration difference of analytes between the aqueous phases containing the analyte and the organic phase constituting the microdrop of a solvent. The limit of detection of HS-SDME for kerosene was 1.5 μL. Overall, the HS-SDME coupled with GC-FID proved to be rapid, simple and sensitive and a good alternative method for the analysis of accelerants in fire debris samples.     

Application of headspace solvent microextraction to the analysis of mononitrotoluenes in waste water samples

The possibility of applying headspace solvent microextraction (HSME) for determination of mononitrotoluenes (MNTs) in waste water samples is demonstrated. A drop of n-amyl alcohol containing naphthalene as an internal standard was suspended from the tip of a microsyringe needle over the headspace of stirred sample solutions for a predescribed extraction period. The drop was then injected directly into a gas chromatograph. Optimization of experimental parameters such as the nature of extracting solvent, microdrop and sample volumes, sampling temperature, stirring rate, ionic strength of the solution, pH and extraction time on HSME efficiency were investigated. Then enrichment factor, dynamic linear range (DLR), limit of detection (LOD) and precision of the method were evaluated by water samples spiked with MNTs. Finally, the method was successfully applied to the extraction and determination of the mononitrotoluenes in waste waters of both P.C.I. Company and Research Center of Azad University.     

Ultrasonic nebulization extraction coupled with headspace single-drop microextraction of volatile and semivolatile compounds from the seed of Cuminum cyminum L

Ultrasonic nebulization extraction (UNE) coupled with headspace single-drop microextraction (HS-SDME) was developed. In the UNE process, the analytes were transferred from the aqueous phase to the gas phase. Then the analytes were transferred from the gas phase to the solvent phase by the carrier gas and extracted and enriched with suspended microdrop solvent. Finally, the microdrop solvent injected into GC-MS system. The parameters affecting extraction performance, such as type of suspended solvent, microdrop volume, flow rate of carrier gas, temperature of extraction vessel and extraction time were investigated and optimized. The proposed method can be applied for the extraction and enrichment of the volatile and semivolatile compounds simultaneously. The extraction efficiency of the proposed method was compared with that of ultrasonic extraction (UE) and UE-HS-SDME. Compared with UE-HS-SDME, the contents of constituents in the extract obtained by the proposed method were closer to those obtained by hydrodistillation (HD), which is a standard extraction method.     

Trace analysis of chlorobenzenes in water samples using headspace solvent microextraction and gas chromatography/electron capture detection

In the present work, a rapid method for the extraction and determination of chlorobenzenes (CBs) such as monochlorobenzene, 1,2-dichlorobenzene, 1,3-dichlorobenzene, 1,4-dichlorobenzene, 1,2,3-trichlorobenzene and 1,2,4-trichlorobenzene in water samples using the headspace solvent microextraction (HSME) and gas chromatography/electron capture detector (ECD) has been described. A microdrop of the dodecane containing monobromobenzene (internal standard) was used as extracting solvent in this investigation. The analytes were extracted by suspending a 2.5 μl extraction drop directly from the tip of a microsyringe fixed above an extraction vial with a septum in a way that the needle passed through the septum and the needle tip appeared above the surface of the solution. After the extraction was finished, the drop was retracted back into the needle and injected directly into a GC column. Optimization of experimental conditions such as nature of the extracting solvent, microdrop and sample temperatures, stirring rate, microdrop and sample volumes, the ionic strength and extraction time were investigated. The optimized conditions were as follows: dodecane as the extracting solvent, the extraction temperature, 45 °C; the sodium chloride concentration, 2 M; the extraction time, 5.0 min; the stirring rate, 500 rpm; the drop volume, 2.5 μl; the sample volume, 7 ml; the microsyringe needle temperature, 0.0 °C. The limit of detection (LOD) ranged from 0.1 μg/l (for 1,3-dichlorobenzene) to 3.0 μg/l (for 1,4-dichlorobenzene) and linear range of 0.5–3.0 μg/l for 1,2-dichlorobenzene, 1,3-dichlorobenzene and from 5.0 to 20.0 μg/l for monochlorobenzene and from 5.0 to 30 μg/l for 1,4-dichlorobenzene. The relative standard deviations (R.S.D.) for most of CBs at the 5 μg/l level were below 10%. The optimized procedure was successfully applied to the extraction and determination of CBs in different water samples.     

Determination of phenols in water using liquid phase microextraction with back extraction combined with high-performance liquid chromatography.

Liquid phase microextraction with back extraction (LPME/BE) combined with high-performance liquid chromatography (HPLC) was studied for the determination of a variety of phenols in water samples. The target compounds were extracted from 2-ml aqueous sample adjusted to pH 1 (donor solution) through a microliter-size organic solvent phase (400-microl n-hexane), confined inside a small PTFE ring, and finally into a 1-microl basic aqueous acceptor microdrop suspended inthe aforementioned solvent phase from the tip of a microsyringe needle. After extracting for a prescribed time, the microdrop was taken back into the syringe and directly injected into an HPLC for detection. Factors relevant to the extraction procedure were studied. At the optimized extraction conditions, a large enrichment factor (more than 100-fold) can be achieved for most of the phenols within 35 min. The detection limit range was 0.5-2.5 microg/l for different analytes in aqueous samples. The results demonstrate the suitability of the LPME/BE approach to the analysis of polar compounds in aqueous samples.     

Liquid-phase microextraction and gas-chromatographic determination of selenium(IV) in aqueous samples

A liquid-phase microextraction (LPME) method was employed for preconcentration of selenium as piazselenol complex in aqueous samples. The samples reacted with o-phenylenediamine in 0.1?M HCl at 90°C for 15?min, and then LPME was performed. A microdrop of carbon tetrachloride was applied as the extracting solvent. After extraction, the microdrop was introduced directly into the injection port of gas chromatography for analysis. Several important extraction parameters such as the type of organic solvent, sample and organic drop volumes, salt concentration, stirring rate, and exposure time were controlled and optimized. In the proposed LPME, the extraction was achieved by suspending a 3?µL carbon tetrachloride drop from the tip of a microsyringe immersed in 12.5?mL of aqueous solution. Under optimized conditions, a dynamic linear range was obtained in the range of 20–1000?µg?L^?1. The preconcentration factor and the limit of detection of selenium in this method were 91 and 0.9?µg?L^?1, respectively. The optimized procedure was successfully applied to the extraction and determination of selenium in different types of real samples. The relative standard deviations for the spiking levels of 50–100?µg?L^?1 in the real samples were in the range of 3.2–6.1%, and the relative errors were located in the range of ?5.4 to 5%.     

Determination of Geosmin and 2-Methylisoborneol in Water by Headspace Liquid-Phase Microextraction Coupled with Gas Chromatography-Mass Spectrometry

Geosmin (GSM) and 2-methylisoborneol (MIB) were extracted from water samples, adsorbed in organic solvent microdrop by headspace liquid-phase microextraction (HS-LPME), and were analyzed by gas chromatography-mass spectrometry (GC-MS). Influence factors such as the extraction solvent types, headspace and microdrop volumes, stirring rate, equilibrium and extraction time, and ionic strength for HS-LPME efficiency were thoroughly evaluated. Under optimized extraction and detection conditions, the calibration curves of GSM and MIB were linear in the range of 5–1000 ng/L. The detection limits of GSM and MIB were 1.1 and 1.0 ng/L, respectively. Average recoveries of 95.45–113.7% (n = 5) were obtained and method precisions were also satisfactory. Trace levels of the off-flavor compounds at ng/L in tap water and raw water were successfully quantified.     

Gas flow headspace liquid phase microextraction

There is a trend towards the use of enrichment techniques such as microextraction in the analysis of trace chemicals. Based on the theory of ideal gases, theory of gas chromatography and the original headspace liquid phase microextraction (HS-LPME) technique, a simple gas flow headspace liquid phase microextraction (GF-HS-LPME) technique has been developed, where the extracting gas phase volume is increased using a gas flow. The system is an open system, where an inert gas containing the target compounds flows continuously through a special gas outlet channel (D = 1.8 mm), and the target compounds are trapped on a solvent microdrop (2.4 μL) hanging on the microsyringe tip, as a result, a high enrichment factor is obtained. The parameters affecting the enrichment factor, such as the gas flow rate, the position of the microdrop, the diameter of the gas outlet channel, the temperatures of the extracting solvent and of the sample, and the extraction time, were systematically optimized for four types of polycyclic aromatic hydrocarbons. The results were compared with results obtained from HS-LPME. Under the optimized conditions (where the extraction time and the volume of the extracting sample vial were fixed at 20 min and 10 mL, respectively), detection limits (S/N = 3) were approximately a factor of 4 lower than those for the original HS-LPME technique. The method was validated by comparison of the GF-HS-LPME and HS-LPME techniques using data for PAHs from environmental sediment samples.     

Headspace solvent microextraction as a simple and highly sensitive sample pretreatment technique for ultra trace determination of geosmin in aquatic media

A headspace solvent microextraction method was developed for the trace determination of geosmin, an odorant compound, in water samples. After performing the extraction by a microdrop of an organic solvent, the microdrop was introduced directly into a GC-MS injection port. One-at-the-time optimization strategy was applied to investigate and optimize some important extraction parameters such as type of solvent, drop volume, temperature, stirring rate, ionic strength, sample volume, and extraction time. The analytical data exhibited an RSD of less than 5% (n = 5), a linear calibration range of 5-900 ng/L (r2 > 0.998), and a detection limit of 0.8 and 3.3 ng/L using two different sets of selected ions. The proposed method was successfully applied to the extraction and determination of geosmin in the spiked real water sample and reasonable recovery was achieved.     

Determination of volatile organic acids in oriental tobacco by needle-based derivatization headspace liquid-phase microextraction coupled to gas chromatography/mass spectrometry

A method coupling needle-based derivatization headspace liquid-phase microextraction with gas chromatography-mass spectrometry (HS-LPME/GC-MS) was developed to determine volatile organic acids in tobacco. The mixture of N,O-bis(trimethylsilyl)trifluoroacetamide and decane was utilized as the solvent for HS-LPME, resulting that extraction and derivatization were simultaneously completed in one step. The solvent served two purposes. First, it pre-concentrated volatile organic acids in the headspace of tobacco sample. Second, the volatile organic acids extracted were derivatized to form silyl derivatives in the drop. The main parameters affecting needle-based derivatization HS-LPME procedure such as extraction and derivatization reagent, microdrop volume, extraction and derivatization time, and preheating temperature and preheating time were optimized. The standard addition approach was essential to obtain accurate measurements by minimizing matrix effects. Good linearity (R(2)> or =0.9804) and good repeatability (RSDs< or =15.3%, n=5) for 16 analytes in spiked standard analytes sample were achieved. The method has the additional advantages that at the same time it is simple, fast, effective, sensitive, selective, and provides an overall profile of volatile organic acids in the oriental tobacco. This paper does offer an alternative approach to determine volatile organic acids in tobacco.     

Headspace single-drop microextraction with in-drop derivatization for aldehyde analysis

A new technique, headspace single-drop microextraction (HS-SDME) with in-drop derivatization, was developed. Its feasibility was demonstrated by analysis of the model compounds, aldehydes in water. A hanging microliter drop of solvent containing the derivatization agent of O-2,3,4,5,6-(pentaflurobenzyl)hydroxylamine hydrochloride (PFBHA) was shown to be an excellent extraction, concentration, and derivatization medium for headspace analysis of aldehydes by GC-MS. Using the microdrop solvent with PFBHA, acetaldehyde, propanal, butanal, hexanal, and heptanal in water were headspace extracted and simultaneously derivatized. The formed oximes in the microdrop were analyzed by GC-MS. HS-SDME and in-drop derivatization parameters (extraction solvent, extraction temperature, extraction time, stirring rate microdrop volume, and the headspace volume) and the method validations (linearity, precision, detection limit, and recovery) were studied. Compared to liquid-liquid extraction and solid-phase microextraction, HS-SDME with in-drop derivatization is a simple, rapid, convenient, and inexpensive sample technique.     

Development of a new microextraction method based on a dynamic single drop in a narrow-bore tube: application in extraction and preconcentration of some organic pollutants in well water and grape juice samples

A novel sample preparation technique, the microextraction method based on a dynamic single drop in a narrow-bore tube, coupled with gas chromatography-flame ionization detection (GC-FID) is presented in this paper. The most important features of this method are simplicity and high enrichment factors. In this method, a microdrop of an extraction solvent assisted by an air bubble was repeatedly passed through a narrow-bore closed end tube containing aqueous sample. It has been successfully used for the analysis of some pesticides as model analytes in aqueous samples. Parameters affecting the method's performance such as selection of extraction solvent type and volume, number of extractions, volume of aqueous sample (tube length), and salt effect were studied and optimized. Under the optimal conditions, the enrichment factors (EFs) for triazole pesticides were in the range of 141-214 and the limits of detection (LODs) were between 2 and 112 μg L⁻¹. The relative standard deviations (C = 1000 μg L⁻¹, n = 6) were obtained in the range of 2.9-4.5%. The recoveries obtained for the spiked well water and grape juice samples were between 71 and 106%. Low cost, relatively short sample preparation time and less solvent consumption are other advantages of the proposed method.     

Hydrodistillation–Headspace Solvent Microextraction: An Efficient Method for Analysis of the Essential Oil from the Seeds of Foeniculum vulgare Mill.

Hydrodistillation–headspace solvent microextraction (HD–HSME) has been used for isolation and preconcentration of the essential oil from the seeds of Foeniculum vulgare Mill. The effect on extraction efficiency of different conditions, for example sample mass, extraction time, microdrop volume, and choice of solvent, was studied and all were optimized. The results were compared with those from hydrodistillation, as reference method. Fourteen compounds were identified; the main components were trans-anethole (70.4%), fenchone (9.3%), and p-allylanisole (8.8%). The results were in good agreement with those obtained by hydrodistillation.     

Extraction of the Volatile and Semivolatile Compounds in Seeds of Cuminum cyminum L. Using Hydrodistillation Followed by Headspace-Ionic Liquid-Based Single-Drop Microextraction

Hydrodistillation (HD) coupled with headspace single-drop microextraction by using ionic liquid (IL) as the extraction solvent, followed by gas chromatography analysis technique, was successfully developed to determine the volatile and semivolatile compounds in seeds of Cuminum cyminum L. In the proposed method, a 1.5-??L microdrop of 1-octyl-3-methylimidazolium hexafluorophosphate, working as the extraction solvent was suspended in the headspace of a 50-mL round-bottom sample flask. After extracting for 30?min, both IL and target analytes were injected into the gas chromatographic system by thermal desorption for 5?s under 240?°C. Then, the IL was retracted back to the microsyringe. Thus, the capillary column should not be contaminated and a clean chromatogram was obtained. The parameters affecting extraction performance were investigated and optimized. The extraction efficiency of the proposed method was compared with that of HD, which is a standard extraction method. The contents of constituents in the extract obtained by the proposed method were close to those obtained by HD. It seems to be an environmentally friendly, time-saving, high efficiency and low solvent consumption technique and would be useful, especially for aromatic plants analysis.     

Griess micro-assay for the determination of nitrite by combining fibre optics-based cuvetteless UV-Vis micro-spectrophotometry with liquid-phase microextraction

A novel, simple and low cost method for the determination of nitrite using headspace single-drop microextraction and cuvetteless ultraviolet-visible micro-spectrophotometry is described. A Griess reagent-containing aqueous microdrop exposed to the headspace was used as extractant of the volatile nitrogen oxides generated from nitrite by direct acidification of the aqueous sample. Experimental parameters affecting the headspace single-drop microextraction performance such as composition and volume of the extractant phase, sample volume, concentration of acetic acid, ionic strength, sample agitation, temperature and microextraction time were systematically examined. Measurements were carried out at 540 nm under optimized conditions. A detection limit of 1.5 μg L⁻¹ and an enrichment factor of 193 were achieved. Intra-day repeatability and inter-day reproducibility, expressed as relative standard deviation, were 3.5% (n = 7) and 10.6% (three consecutive days), respectively. The proposed method, characterized by its enhanced sensitivity and selectivity in comparison with the standardized colorimetric assay, was successfully applied to the analysis of several environmental water samples.     

A Comparative Study of Hydrodistillation and Hydrodistillation–Solvent Microextraction Methods for Identification of Volatile Components of Echinophora cinerea

A recently developed hydrodistillation–solvent microextraction (HD–SME) method coupled to gas chromatography–mass spectrometry (GC–MS) was applied to the analysis of volatile components of aerial parts of Echinophora cinerea (Boiss). By the use of a simplex optimization method, the effects of extraction time, sample weight and microdrop volume on the extraction efficiency of the method were optimized. In the optimized conditions, 3 µL of n-heptadecane was suspended in the headspace of 6 g of hydrodistillating sample, using a microsyringe. After 7 min, the solvent was retracted back into the syringe and directly injected into the GC–MS injection port. The HD–SME method was compared to a conventional hydrodistillation technique. In general, the extraction with HD–SME was relatively faster and required smaller amounts of sample. The microextraction method also showed some selectivity towards α-phellandrene and Z-β-ocimene monoterpenes. A precision better than 6.5% (expressed as relative standard deviation) was obtained for the method.