Development and characterization of an amperometric sensor for triclosan detection based on electropolymerized molecularly imprinted polymer

A novel amperometric sensor based on electropolymerized molecularly imprinted polymer (MIP) for triclosan detection is reported. The sensor was prepared by electropolymerizing o-phenylenediamine (o-PD) on a glassy carbon electrode in the presence of template triclosan. The template can be quickly removed by NaOH solution. After incubating in acetate buffer for 15 min, the sensor response sensitively to triclosan over a linear range of 2.0 × 10^{− 7} to 3.0 × 10^{− 6} mol/L and a detection limit as low as 8.0 × 10^{− 8} mol/L is obtained. This sensor provides an efficient way for eliminating interferences from compounds with similar structures to that of triclosan.     

Chromatographic characterisation, under highly aqueous conditions, of a molecularly imprinted polymer binding the herbicide 2,4-dichlorophenoxyacetic acid

The affinity of a 2,4-dichlorophenoxyacetic acid (2,4-D) molecularly imprinted polymer (MIP), which was synthesised directly in an aqueous organic solvent, for its template (2,4-D) was studied and compared with the affinity exhibited by two other reference (control) polymers, NIPA and NIPB, for the same analyte. Zonal chromatography was performed to establish the optimal selectivity, expressed as imprinting factor (IF), under chromatographic conditions more aqueous than those described so far in the literature. Frontal analysis (FA) was performed on columns packed with these polymers, using an optimized mobile phase composed of methanol/phosphate buffer (50/50, v/v), to extract adsorption isotherm data and retrieve binding parameters from the best isotherm model. Surprisingly, the template had comparable and strong affinity for both MIP (K = 3.8 × 10⁴ M⁻¹) and NIPA (K = 1.9 × 10⁴ M⁻¹), although there was a marked difference in the saturation capacities of selective and non-selective sites, as one would expect for an imprinted polymer. NIPB acts as a true control polymer in the sense that it has relatively low affinity for the template (K = 8.0 × 10² M⁻¹). This work provides the first frontal chromatographic characterization of such a polymer in a water-rich environment over a wide concentration range. The significance of this work stems from the fact that the chromatographic approach used is generic and can be applied readily to other analytes, but also because there is an increasing demand for well-characterised imprinted materials that function effectively in aqueous media and are thus well-suited for analytical science applications involving, for example, biofluids and environmental water samples.     

三氯生分子印迹传感器的制备及其性能研究

应用分子印迹技术, 以邻苯二胺为功能单体、三氯生为模板, 用循环伏安法在玻碳电极表面合成了性能稳定的三氯生分子印迹聚合膜, 并用方波伏安法对此印迹传感器进行了分析应用研究.     

Synthesis,characterization and application of dummy-template molecularly imprinted microspheres for 2,4-d butyl ester

Dummy-template molecularly imprinted microspheres were synthesized via precipitation polymerization employing 2,4-D isooctyl ester as the template molecule instead of 2,4-D butyl ester, while methacrylic acid and divinylbenzene were used as functional monomer and cross-linker in acetonitrile or a mixture of acetonitrile and toluene. The microspheres were characterized by scanning electron microscopy, laser particle size analyzer and fourier transform infrared spectrometry. Binding capacity experiment showed that the molecularly imprinted polymers prepared in a mixture of acetonitrile and toluene had a high binding capacity. The performance of microspheres was further assessed by equilibrium binding and kinetic adsorption experiments. The results showed that the apparent maximum adsorption reached up to 1.35 mg·g^?1 within 10 min. Based on the dummy-template microspheres, a molecularly imprinted solid phase extraction-gas chromatography method was developed for the selective analysis of 2,4-D butyl ester in soil samples. The mean recoveries of 2,4-D butyl ester from blank soil samples ranged from 85.9 to 99.3% with relative standard deviations of 4.5–14.3% (n = 5). The limit of detection and the limit of quantification of 2,4-D butyl ester were 0.8 μg·kg^?1 and 2.3 μg·kg^?1, respectively.     

葛根素分子印迹电化学传感器的制备及研究

以丙烯酰胺为功能单体,葛根素为模板分子,马来松香丙烯酸乙二醇酯为交联剂,采用循环伏安法合成了葛根素分子印迹膜,并以此为识别元件制备了葛根素电化学传感器。该传感器对葛根素具有高度的选择性和良好的敏感度,葛根素氧化峰电流与其浓度在6.0×10-8～1.6×10-3mol/L范围内呈良好的线性关系,检出限为2.0×10-8mol/L。将此传感器用于葛根素注射液和木瓜葛根片中葛根素的含量测定,回收率为97.7%～106.4%。     

Capacitive chemical sensor for fenvalerate assay based on electropolymerized molecularly imprinted polymer as the sensitive layer

A capacitive chemical sensor for fenvalerate is reported. By using ac impedance measurements the sensor has been based on the decrease in capacitance caused by the analyte used as the template in the formulation of an electropolymerized molecularly imprinted polymer as receptor layer. Improvement of the insulating properties of the sensor was investigated in detail. The capacitive sensor was prepared by a deposition of a self-assembled monolayer of 2-mercaptobenzimidazole (2-MBI) before electropolymerization of 2-MBI and subsequent treatment with n-dodecanethiol to eliminate pinholes and defects in the polymerized 2-MBI film. From the calibration curve concentrations of fenvalerate up to 9 g mL^–1 could be detected with a linear determination range up to 5 g mL^–1 and a detection limit of 0.36 g mL^–1. No significant interference was observed from common pyrethroid insecticides.     

2,4-二氯苯氧基乙酸的光转化化学发光机理研究

实验发现,2,4-二氯苯氧基乙酸(2,4-D)经紫外光转化后与KMnO4在H2SO4介质中反应可产生化学发光。采用液相色谱-质谱联用技术(LC-MS)对2,4-D光降解产物进行分析,推断光降解主要生成了多酚类降解产物,如2-氯对苯二酚(CHQ)和4-氯邻苯二酚等。化学发光光谱研究发现,2,4-D经紫外光转化后,与KMnO4反应的发光波长为690 nm,与2,4-D的典型降解产物CHQ的化学发光光谱一致。此发光现象是氧化还原过程中生成的Mn?吸收反应所释放出的化学能成为激发态,再返回基态时产生的特征辐射峰。该反应体系可用于2,4-D的检测,当2,4-D浓度在0.01～10 mg/L范围内与发光强度呈良好的线性关系;检出限为3.0μg/L。     

三聚氰胺磁性分子印迹聚合物材料的制备及性能表征

利用溶剂热法通过控制反应时间和温度制得了分散性好和磁性强的Fe3O4,并利用溶胶凝胶法制备得到包覆SiO2的磁性微球(Fe3O4@SiO2)。以三聚氰胺为模板分子,甲基丙烯酸(MAA)为单体,采用本体聚合法制备了磁性分子印迹聚合物(MMIPs)。通过静态吸附实验表明,MMIPs对三聚氰胺的饱和吸附量高达10.22μg/mg,是磁性非印迹聚合物(MNIPs)的1.62倍。粒子扩散模型、Elovich模型和动态吸附实验表明所制得的MMIPs有较好的吸附性能。     

大黄酸分子印迹聚合物微球的制备及特性

以聚苯乙烯微球为种球,大黄酸为模板分子,采用单步溶胀聚合法在N,N-二甲基甲酰胺体系中制备了单分散分子印迹聚合物微球.用扫描电镜对微球的结构和形貌进行了表征,并研究了微球的制备条件和吸附特性.微球的凹槽可有效地增加微球的比表面积和结合位点,从而提高了模板分子的结合速率及微球的印迹容量.     

Preparation of hydrophilic molecularly imprinted polymers for tetracycline antibiotics recognition

Hydrophilic molecularly imprinted polymers(MIPs) were prepared using tetracycline as template,methacrylic acid as monomer and glycidilmethacrylate as pro-hydrophilic co-monomer.Compared with common MIPs,the imprinting effect and adsorption amounts of hydrophilic MIPs for tetracycline(TC) were greatly improved in water media.Furthermore,the electrochemical sensor fabricated by modifying hydrophilic MIPs on glassy carbon electrode was developed for the determination of TC in foodstuff samples.     

Preparation and characterization of monodisperse molecularly imprinted polymers for the recognition and enrichment of oleanolic acid

Monodisperse molecularly imprinted polymers for oleanolic acid were successfully prepared by a precipitation polymerization method using oleanolic acid as a template, methacrylic acid as a functional monomer, and divinylbenzene/ethylene glycol dimethacrylate as a crosslinker in a mixture of acetonitrile and ethanol (3:1, v/v). The imprinted polymers and nonimprinted polymers were characterized by using scanning electron microscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The resulting imprinted polymers had average diameters of 3.15 μm and monodispersity values of 1.024. The results clearly demonstrate that use of ethanol as a cosolvent is indeed exceedingly effective in promoting the dissolution of oleanolic acid and in obtaining uniform microspheres. Molecular recognition properties and binding capability to oleanolic acid were evaluated by adsorption testing, which indicated that the imprinted polymers displayed optimal binding performance with a maximum adsorption capacity of 17.3 mg/g and a binding saturation time of 80 min. Meanwhile, the produced imprinted polymers exhibited higher selectivity to oleanolic acid than that for ursolic acid and rhein. Herein, the studies can provide theoretical and experimental references for the oleanolic acid molecular imprinted system.     

Preparation and characterization of a novel molecularly imprinted polymer for the separation of glycyrrhizic acid

Molecularly imprinted polymers of glycyrrhizic acid were prepared by solution polymerization using glycyrrhizic acid as the template molecule, N‐vinypyrrolidone as functional monomer, N ,N‐methylene bisacrylamide as cross‐linker and ascorbic acid and hydrogen peroxide as initiators. Focused on the adsorption capacity and separation degree of the polymer to glycyrrhizic acid, the effects of the monomers, crosslinker and initiators were investigated and optimized. Finally, the structure of the polymer was characterized by using Fourier transform infrared spectroscopy and scanning electron microscopy. To obtain objective results, non‐imprinted molecular polymers prepared under the same conditions were also characterized. The adsorption quantity of the polymer was measured by high‐performance liquid chromatography. Under the optimum conditions, the maximum adsorption capacity of glycyrrhizic acid approached 15 mg/g, and the separation degree was as high as 2.5. The adsorption kinetics could be well described by a pseudo‐first‐order model, while the thermodynamics of the adsorption process could be described by the Langmuir model.     

脂质体免疫传感器的制备及其应用于测定尿液中2,4-D的量

将4种溶质(以10∶10∶1∶1质量比混合的DPPC、胆固醇、DPPG及DPPE)的混合物22mg,溶于4mL氯仿-异丙醚-甲醇(6+6+1)混合溶剂中。向此溶液中加入0.15mol·L-1亚铁氰化钾溶液1mL,于45℃超声涡旋5min使其包埋于脂质体中。将此脂质体包埋的亚铁氰化钾溶液1mL,通过戊二醛(0.7+99.3)溶液2mL的作用,与200μL 2,4-D免抗体溶液(10.53g.L-1)交联。另将自制MWNT′s修饰的石墨电极插入0.05mol·L-1脂质体-抗体-吡咯溶液中,用循环伏安法在0～0.75V电位区间扫描10次,扫描速率为50mV.s-1。由此制成的免疫传感器应用于测定尿样中2,4-D含量,其线性范围为0.05～2.5 mg·L-1之间,检出限(3S/N)为15.4μg·L-1。     

水胺硫磷分子印迹传感器的制备与应用

在磷酸盐缓冲溶液(PBS)中,以邻苯二胺(o-PD)和没食子酸(GA)为功能单体,水胺硫磷(ICP)为模板分子,采用电位循环扫描法在玻碳电极(GCE)表面进行电聚合,形成绝缘性的分子印迹膜,通过电化学阻抗谱(EIS)和循环伏安法(CV)对分子印迹膜进行表征.在最佳实验条件下,以铁氰化钾[ K3Fe(CN)6]为探针,用差分脉冲伏安法( DPV)对ICP进行定量分析.该传感器在2.00×10 -7～2.00×10-4 mol/L范围内,传感器的响应信号与ICP的浓度呈良好的线性关系,检测限为6.06×10-s mol/L( S/N=3).将其用于蔬果等实际样品中ICP的测定,回收率为95.6％～104.0％.     

马尿酸分子印迹电化学传感器的制备及应用

采用超声法制备g-C3N4/NiO复合催化材料,将其滴涂在玻碳电极(GCE)表面构建g-C3N4/NiO/GCE催化电极。采用电聚合方法,以马尿酸为模板分子,邻苯二胺为功能单体构建M IP/g-C3N4/NiO/GCE传感器。采用时间-电流法对传感器制备条件优化。结果表明,复合催化材料对H2O2具有良好的催化效果。分子印迹传感器对马尿酸具有良好的选择性。在优化条件下,马尿酸质量浓度在0.05~2 mg/L范围内,电极电流响应与浓度呈良好的线性关系,检出限为7.1μg/L。将电极用于尿液中马尿酸的检测,回收率在87.3%~95.3%之间。     

Preparation and characterization of molecularly imprinted silica monolith for screening sulfamethazine

In this work, a novel approach of preparing molecularly imprinted film‐derivatized silica monolith materials was developed by a two‐step procedure. The silica monolithic support was first prepared by the sol–gel method with tetramethoxysilane as the precursor. Subsequently, vinyl groups were introduced onto the surface of silica monolith by immobilization of γ‐methacryloxypropyltrimethoxysilane. The prepolymerization mixtures, consisting of methacrylic acid as a functional monomer, ethylene dimethacrylate as a crosslinker, sulfamethazine as a template molecule and an ionic liquid as porogen, were injected into the silica monolith immobilized vinyl groups to form the molecularly imprinted films on the surface of the vinyl functionalized silica monolith. The monolithic materials were characterized by SEM, Fourier transform IR and solid‐state reflection UV spectra. The resulted imprinted materials were evaluated under CEC and HPLC mode. The results indicated that there were enough recognition sites on the surface of the imprinted film‐derivatized monolithic materials for selectively recognizing sulfamethazine from the sulfonamide mixture. Ionic liquids, which was utilized as the porogens, could improve the flow‐through property and the imprinting effect of the molecularly imprinted film‐functionalized silica monolithic materials.     

Electrochemical determination of 2,4-D at a mercury electrode

An indirect electrochemical determination of 2,4-dichlorophenoxyacetic acid (2,4-D), has been presented. The method is based on the adsorption and desorption of 2,4-D on mercury electrode. Also, the electrochemical behavior of 2,4-D in aqueous solutions at different pH values and different 2,4-D concentrations were studied. A simple and rapid method has been developed for its extraction from water and soil. The subsequent determination was carried out by a tensammetric method. Three calibration curves could be obtained from different parts of voltammogram. Under the optimum conditions (pH = 2.3; E_acc = −1100 mV; t_acc = 60 s; alternative current mode; ν = 40 mV s⁻¹; pulse height = 20 mV; modulation frequency = 60 Hz; phase angle = 90°) the limit of detection was 50 μg L⁻¹. The proposed method was applied to the determination of 2,4-D in real samples such as soil and water.     

Chromatographic characterization of molecularly imprinted polymers

Recent efforts in the investigation of chromatographic characterization of molecularly imprinted polymers (MIPs) have focused mainly on the nature of heterogeneous binding sites. More data on the thermodynamics than on the kinetic features of MIP columns have been published. The present article addresses the sources of peak broadening and tailing, which are the main drawbacks often associated with imprinted polymers in chromatography for practical applications. With use of the theory of nonlinear chromatography, the peak properties of a MIP column, including the retention and peak broadening and tailing, can be well interpreted. Efforts to improve chromatographic efficiency using MIPs prepared by approaches different from the conventional method, including covalent imprinting and the format of uniformly sized spherical microbeads, are reviewed and discussed. This review leads to the conclusion that nonlinear chromatography theory is useful for characterizing chromatographic features of MIP columns, since a MIP is essentially an affinity-based chromatographic stationary phase. We expect more theoretical and experimental studies on the kinetic aspects of MIP columns, especially the factors influencing the apparent rate constant, as well as the analysis of the influences of mobile-phase composition on the chromatographic performance. In addition to revealing the affinity interaction by molecular recognition, slow nonspecific interactions which may be inherited from the imperfect imprinting and may be involved in the rebinding of the template to MIPs also need to be characterized. Figure The peak broadening and tailing associated often with molecularly imprinted polymers (MIPs) in column chromatography for practical applications can be well characterized by the theory of nonlinear chromatography.     

核壳结构的萘夫西林磁性分子印迹聚合物微球的制备及性能

以表面修饰双键的Fe₃O₄@SiO₂纳米颗粒为基体,以萘夫西林(nafcillin)为模板,甲基丙烯酸(MAA)为单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂,偶氮二异丁腈(AIBN)为引发剂,采用三步升温聚合法合成了核壳结构的萘夫西林磁性分子印迹聚合物。采用傅里叶变换红外光谱仪(FT-IR)、透射电子显微镜(TEM)、X射线衍射仪(XRD)和振动样品磁强计(VSM)对制备的印迹聚合物微球进行了表征,得到的磁性印迹聚合物微球的粒径在320 nm左右,大小均匀,分散性较好,可以在外加磁场下与溶剂实现快速分离。对磁性印迹和非印迹聚合物进行了吸附性能研究,结果表明该印迹聚合物微球对模板分子具有很高的吸附容量(50.7 mg/g),特异性识别性能良好(印迹因子为2.46),有望应用于实际样品中萘夫西林残留量的富集分析。     

Preparation and characterization of temperature response molecularly imprinted membrane with chitosan and methylmethacrylate

In this study, a novel temperature controlled molecularly imprinted membrane (Temp-Ctrl-MIM) made of chitosan and methyl methacrylate was fabricated with bovine serum albumin (BSA) as template molecule. The film was characterized by infrared spectroscopy (IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and the permeation experiment. The results revealed that the porous structure of the film was as similar as the BSA. Moreover, the membrane had advanced molecular imprinting capability to BSA comparing to pepsin and casein at any temperature and the film demonstrated an excellent ability to identify specific template molecule (BSA) at the synthesis temperature comparing to other temperatures.