Simultaneous determination of Mn(II), Cu(II) and Fe(III) as 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol complexes by adsorptive cathodic stripping voltammetry at a carbon paste electrode

A simple and precise square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV) method has been described for simultaneous determination of Mn(II), Cu(II) and Fe(III) in water samples using a carbon paste electrode. In 0.1 mol L⁻¹ acetate buffer (pH 5) containing 50 μmol L⁻¹ of 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol (5-Br-PADAP), Mn(II), Cu(II) and Fe(III) were simultaneously determined as metal-complexes with 5-Br-PADAP following preconcentration onto the carbon paste electrode by adsorptive accumulation at +1.0 V (vs. Ag/AgCl/3 M KCl). Insignificant interference from various cations (K⁺, Na⁺, Mg²⁺, Ca²⁺, Al³⁺, Bi³⁺, Sb³⁺, Se⁴⁺, Zn²⁺, Ni²⁺, Co²⁺, Cd²⁺, Pb²⁺, V⁵⁺, Ti⁴⁺ and NH₄⁺), anions (HCO₃⁻, Cl⁻, NO³⁻, SO₄²⁻ and PO₄³⁻) and ascorbic acid was noticed. Limits of detection of 0.066, 0.108 and 0.093 μg L⁻¹ and limits of quantitation of 0.22, 0.36 and 0.31 μg L⁻¹ Mn(II), Cu(II) and Fe(III), respectively, were achieved by the described method. The described stripping voltammetry method was successfully applied for simultaneous determination of Mn(II), Cu(II) and Fe(III) in ground, tap and bottled natural water samples.     

Sensitive spectrophotometric determination of vanadium with 2-(5-bromo-2-pyridylazo)-5-diethyl-aminophenol (5-Br-PADAP)

A new sensitive and highly selective method is described for the spectrophotometric determination of microgram amounts of vanadium(V). First, vanadium is isolated by extraction withN-benzoyl-N-phenylhydroxylamine (BPHA) in chloroform from about 4M hydrochloric acid medium. Then, chloroform is evaporated and the residue mineralized with mixture of cone. perchloric and nitric acid. Finally, a colour reaction of vanadium(V) separated with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) in an acetate buffer (pH 4.5) gives a molar absorptivity of 5.48×10⁴l·mol^–1·cm^–1 at 585 nm. The proposed method was applied for the determination of traces of vanadium in aluminium samples. The results obtained show a good precision and accuracy of the method.     

Sensitive spectrophotometric determination of bismuth(III) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

The complex of the reagent 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) with Bi(III) has been studied. The composition and stability of this complex have been determined. An analytical method for the spectrophotometric determination of Bi(III) using its complex with 5-Br-PADAP has been developed. Variables influencing the method such as pH, wavelength, and time have been studied. The limitations of this method and the effect of interfering ions have been investigated. Comparison of this method with other methods cited in the literature for the determination of Bi(III) is also included.     

Second derivative spectrophotometric method for simultaneous determination of cobalt, nickel and iron using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

A simple, sensitive and rapid derivative spectrophotometric method using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) has been developed for simultaneous determination of Co(II), Ni(II) and Fe(II) which have very similar chemical behavior and appear together in many real samples. The complexes of all these metal ions with 5-Br-PADAP were formed immediately at pH 7.0 ammonium acetate buffered solution and were stable for at least 24 h. Second derivative spectra were selected for evaluation, because working wavelength determination was more precise and spectral overlap was less than in the ordinary and first derivative spectra. Three wavelengths at which the complexes exhibit extremum ²D values for Co(II), Ni(II) and Fe(II) were selected as analytical wavelengths, i.e., 640, 600 and 740 nm, respectively. Calibration curves drawn with zero-to-peak values at mentioned wavelengths were linear between 80 and 2000 ng ml⁻¹ for each metal ion. Concentrations of Co(II) and Ni(II) were calculated from the total ²D values and the sum of the linear equations for these three cations at 640 and 600 nm, after Fe(II) assay by making use of the ²D value at 740 nm. Limits of detection (LOD) for Co(II), Ni(II) and Fe(II) were 2.7, 13.9 and 3.0 ng ml⁻¹, respectively. The method has been applied to tool steel and heater resistance wire samples successfully.     

Synthesis of amberlite XAD-2-PC resin for preconcentration and determination of trace elements in food samples by flame atomic absorption spectrometry

A new chelating sorbent has been developed using Amberlite XAD-2 resin anchored with pyrocatechol through –N=C– group. This sorbent, characterised by elemental analysis and infrared (IR) spectra, was used as packing for the minicolumn in an on-line system preconcentration system for cadmium, cobalt, copper and nickel determination. Metal ions were sorbed in the minicolumn, from which it could be eluted directly to the nebulizer–burner system of the flame atomic absorption spectrometer (FAAS). Elution of all metals from minicolumn can be made with 0.50 mol L^− 1 HCl or HNO₃. The enrichment factors obtained were 16 (Cd), 24 (Co), 15 (Cu) and 19 (Ni), for 60 s preconcentration time, and 39 (Cd), 69 (Co), 36 (Cu) and 41 (Ni), if used 180 s preconcentration time. Under the optimum conditions, the proposed procedure allowed the determination of cadmium, cobalt, copper and nickel with detection limits of 0.31, 0.32, 0.39 and 1.64 μg L^− 1, respectively, when used preconcentration periods of 180 s. The accuracy of the developed procedure was sufficient and evaluated by the analysis of the certified reference materials NIST 1515 apple leaves and NIST 1570a spinach leaves. The method was applied to the analysis of food samples (spinach, black tea and rice flour).     

Spectrophotometric determination of cadmium(II) using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

The complex of cadmium with the reagent 2-(-5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) has been studied. The composition, stability constant, and free energy change of formation of the complex have been determined. A sensitive spectrophotometric method for the determination of cadmium has been developed and applied for a range of concentration of 0.4–4.0 μg/ml cadmium using the complex Cd-5-Br-PADAP. The optimum conditions for maximum sensitivity of determination such as standing time, pH, wavelength, and order of addition have been determined. The effect of foreign ions on this method has been also studied.     

Rapid spectrophotometric determination of zirconium with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

Zirconium reacts with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in the pH range 3.8-5.8 to form a red chelate that is soluble in methanol-water mixtures. The absorbance of the 1:3 complex obeys Beer's law over the zirconium concentration range 0.02-0.44 mug/ml and has a molar absorptivity of 1.54 x 10(5) 1.mole(-1). cm(-1) at 585 nm. The formation constant is log beta(3) = 16.15. Of 59 species studied, only EDTA, Ga, In, Ti, Hf and V(V) interfere seriously.     

Ammonium tetraphenylborate-naphthalene adsorbent for the preconcentration and trace determination of uranium in standard alloys and synthetic samples using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol by fourth-derivative spectrophotometry

A solid ion-pair material produced from ammonium tetraphenylborate (ATPB) and naphthalene has been used for the preconcentration of uranium from the large volume of its aqueous complex samples. Uranium reacts with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) to form a water insoluble, coloured complex. This complex is quantitatively retained on the ATPB-naphthalene adsorbent filled in a column in the pH range 7.0–9.5 and at a flow rate of 2 ml/min. The solid mass from the column is dissolved with 5 ml of dimethylformamide (DMF) and uranium is determined by fourth-derivative spectrophotometry. The calibration curve is linear over the concentration range of 0.13–15.0 g of uranium in 5 ml of the final DMF solution. Seven replicate determinations of 6 g of uranium gave a mean peak height (peak-to-peak signal between 592 nm and 582 nm) of 1.02 with a relative standard deviation of 0.95%. The sensitivity is 0.8419 (d⁴A/d⁴)/(g ml^–1) found from the slope of the calibration curve. The interference of a large number of anions and cations on the estimation of uranium has been studied and the method applied for the determination of uranium in coal fly ash, Zr-base alloy and some synthetic samples corresponding to standard alloys.     

Column chromatographic separation of metal ions on 1-(2-pyridylazo)-2-napthol modified amberlite IR-120 resin

Cation exchange resin, Amberlite IR-120, has been modified by the sorption of 1-(2-pyridylazo)-2-napthol (PAN) at pH 6.0. The optimum conditions for the sorption of PAN on the resin have been established. The maximum sorption of PAN was found to be 8.70 micromol/g. In order to explore the separation possibilities of the material, distribution coefficients of a number of metal ions were determined in various solvent systems. A number of binary separations of metal ions of analytical interest have been carried out using columns packed with this material. In order to demonstrate the practical utility of this material, Zn2+ and Hg2+ have been selectively separated from synthetic mixtures of metal ions and assay of Zn2+ and Fe2+ in commercially available pharmaceutical tablets; namely Fesofor-Z and FE-Z, was carried out.     

Sensitive spectrophotometric determination of nickel(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

A simple, selective and highly sensitive procedure for spectrophotometric determination of nickel has been developed. At pH 5.5, nickel reacts with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in water-ethanol medium to form a red-violet complex which has two absorption maxima, at 520 and 56Onm. The molar absorptivity at 56Onm is 1.26 x 10(5) l.mole(-1).cm(-1). Beer's law is obeyed for 0-15 mug of nickel. Nickel in aluminium alloys and electroplating waste-water has been determined by this method.     

Speciation of Cr(III) and Cr(VI) in water after preconcentration of its 1,5-diphenylcarbazone complex on amberlite XAD-16 resin and determination by FAAS

A simple and sensitive method for the speciation, separation and preconcentration of Cr(VI) and Cr(III) in tap water was developed. Cr(VI) has been separated from Cr(III) and preconcentrated as its 1,5-diphenylcarbazone complex by using a column containing Amberlite XAD-16 resin and determined by FAAS. Total chromium has also been determined by FAAS after conversion of Cr(III) to Cr(VI) by oxidation with KMnO₄. Then, Cr(III) has been calculated by subtracting Cr(VI) from the total. The effect of acidity, amount of adsorbent, eluent type and flow rate of the sample solution on to the preconcentration procedure has been investigated. The retained Cr(VI) complex was eluated with 10 ml of 0.05 mol l⁻¹ H₂SO₄ solution in methanol. The recovery of Cr(VI) was 99.7±0.7 at 95% confidence level. The highest preconcentration factor was 25 for a 250 ml sample volume. The detection limit of Cr(VI) was found as 45 μg l⁻¹. The adsorption capacity of the resin was found as 0.4 mg g⁻¹ for Cr (VI). The effect of interfering ions has also been studied. The proposed method was applied to tap water samples and chromium species have been determined with the relative error <3%.     

Stripping voltammetric determination of Cd(II) based on multiwalled carbon nanotube functionalized with 1-(2-pyridylazo)-2-naphthol

The present work has focused on the modification of multiwalled carbon nanotube with a ligand,l-（2-pyridylazo）-2-naphthol, and its potential application for the development of a new,simple and selective modified glassy carbon electrode for stripping voltammetric determination of Cd（Ⅱ）.The analytical curve for Cd（Ⅱ） ions covered the linear range varying from 0.8 up to 220.4μgL^-1.The limit of detection was found to be 0.1μgL^-1,while the relative standard deviation（RSD） at 50.0μgL^-1 was 1.8%（n=5）.This modified electrode was successfully applied for determination of Cd（Ⅱ） in some water samples.     

Spectrophotometric determination of gadolinium(III) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP)

Reaction between gadolinium(III) and 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5- Br-PADAP) was studied for delineating optimal conditions for complexation. This reagent can be used for the spectrophotometric determination of Gd(III) in concentrations ranging from 0.04 to 1.2 ppm (a = 1.76(+/- 0.03) x 10(5) (1.(-1) mole(-1). cm). The reaction takes place at a pH between 9.2 and 11.6. In the presence of Triton X-100 this complex is soluble in water. In order to overcome difficulties caused by the presence of other lanthanides, an ion exchange chromatographic technique was used.     

The renewable bismuth bulk annular band working electrode: Fabrication and application in the adsorptive stripping voltammetric determination of nickel(II) and cobalt(II)

The paper presents the first report on fabrication and application of a user friendly and mercury free electrochemical sensor, with the renewable bismuth bulk annular band working electrode (RBiABE), in stripping voltammetry (SV). The sensor body is partly filled with the internal electrolyte solution, in which the RBiABE is cleaned and activated before each measurement. Time of the RBiABE contact with the sample solution is precisely controlled. The usefulness of this sensor was tested by Ni(II) and Co(II) traces determination by means of differential pulse adsorptive stripping voltammetry (DP AdSV), after complexation with dimethylglyoxime (DMG) in ammonia buffer (pH 8.2). The experimental variables (composition of the supporting electrolyte, pre-concentration potential and time, potential of the RBiABE activation, and DP parameters), as well as possible interferences, were investigated. The linear calibration graphs for Ni(II) and Co(II), determined individually and together, in the range from 1 × 10⁻⁸ to 70 × 10⁻⁸ mol L⁻¹ and from 1 × 10⁻⁹ to 70 × 10⁻⁹ mol L⁻¹ respectively, were obtained. The calculated limit of detection (LOD), for 30 s of the accumulation time, was 3 × 10⁻⁹ mol L⁻¹ for Ni(II) in case of a single element’s analysis, whereas the LOD was 5 × 10⁻⁹ mol L⁻¹ for Ni(II) and 3 × 10⁻¹⁰ mol L⁻¹ for Co(II), when both metal ions were measured together. The repeatability of the Ni(II) and Co(II) adsorptive stripping voltammetric signals obtained at the RBiABE were equal to 5.4% and 2.5%, respectively (n = 5). Finally, the proposed method was validated by determining Ni(II) and Co(II) in the certified reference waters (SPS-SW1 and SPS-SW2) with satisfactory results.     

Simultaneous determination of Cd(II) and Pb(II) by differential pulse anodic stripping voltammetry based on graphite nanofibers-Nafion composite modified bismuth film electrode

A bismuth-film modified graphite nanofibers-Nafion glassy carbon electrode (BiF/GNFs-NA/GCE) was constructed for the simultaneous determination of trace Cd(II) and Pb(II). The electrochemical properties and applications of the modified electrode were studied. Operational parameters such as deposition potential, deposition time, and bismuth ion concentration were optimized for the purpose of determination of trace metal ions in 0.10 M acetate buffer solution (pH 4.5). Under optimal conditions, based on three times the standard deviation of the baseline, the limits of detection were 0.09 μg L⁻¹ for Cd(II) and 0.02 μg L⁻¹ for Pb(II) with a 10 min preconcentration. In addition, the BiF/GNFs-NA/GCE displayed good reproducibility and selectivity, making it suitable for the simultaneous determination of Cd(II) and Pb(II) in real sample such as river water and human blood samples.