黄芩甙在玻碳电极上的电化学行为及其应用

用线性扫描伏安法(LSV)、循环伏安法(CV)和常规脉冲伏安法(NPV)等多种电化学方法研究了黄芩甙在玻碳电极上的电化学行为,并建立了尿样和血清样品中黄芩甙的微分脉冲伏安(DPV)测定法。实验结果表明:黄芩甙在玻碳电极上的吸附符合Frumkin吸附等温式,吸附自由能为-35.01kJ mol。采用整体电解法求得电极反应电子数为2,并结合Nernst方程式推导了反应机理。黄芩甙在玻碳电极上预富集后,在4.20×10-10～1.05×10-5mol L范围内分段呈线性关系,对5.60×10-7mol L黄芩甙溶液连续6次测定的RSD=2.0%,检出限为2.8×10-10mol L。     

活化玻碳电极伏安法测定锰的研究

采用活化玻碳电极(GC)以伏安法对测定锰进行了研究。结果表明:沉积于电极表面的二氧化锰对锰(Ⅱ)的电化学氧化具有自催化作用,活化GC电极可极大地提高测定锰的灵敏度。在0.04mol LNH3 NH4Cl(pH9.0)底液中,锰浓度在6.0×10-8～1.0×10-5mol L范围内成线性关系,检出限为4.0×10-8mol L。用3×10-7mol L锰溶液重复测定9次,RSD为1.6%。     

芦丁在纳米金修饰玻碳电极上的电化学行为及其测定

采用循环伏安法将纳米金电沉积于玻碳电极表面,制备了纳米金修饰玻碳电极(NG/GCE).在pH3.29的Britton-Robinson(B-R)缓冲溶液中,用循环伏安法研究了芦丁在NG/GCE上的电化学行为.结果表明,NG/GCE对芦丁的氧化还原反应有良好的电催化作用.用方波伏安法测得芦丁的还原峰电流与其浓度在2.0×10-8～2.0×10-6mol/L范围内呈线性关系,检出限为1.0×10-8mol/L(S/N=3).     

隐丹参酮的电化学行为及其测定

采用循环伏安法研究隐丹参酮在电极上的电化学行为及建立差示脉冲伏安对其测定的新方法。在pH 4.0乙酸盐缓冲液中,氧化峰电流与隐丹参酮浓度在3.0×10-8~2.0×10-7mol/L范围内呈良好的线性关系,检出限为2.0×10-9mol/L。玻碳电极可有效消除样品中其它组分对隐丹参酮测定的干扰,已用于实际样品中隐丹参酮的直接测定。该方法灵敏度高、检测范围宽。     

Determination of nitrite with a nano-gold modified glassy carbon electrode by cyclic voltammetry

Abstract

Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) was employed to determine the concentration of rare earth elements (REEs) in plants and soils. Sample preparation and analytical conditions were investigated to set up a simple routine procedure for measuring rare earth elements. For prompt sample decomposition, a microwave digestion technique was successfully used with an acid mixture of HCl+HNO₃+HF. Detection limits, reproducibility, accuracy and possible interference were also studied. ICP-MS provided extremely low detection limits for REEs (0.6–6ng/l). Precision was typically better than 6% RSD (relative standard deviation) for soil and 10% for plant. The potential of the method was evaluated by analysis of standard reference materials of soils and plants. A good agreement between the experimental results and certified values was observed. The spectroscopic interference of Ba with Eu and light REEs(LREEs, La-Eu) with heavy REEs(HREEs, Gd-Lu) were eliminated by the algebra correction.

The results suggested that REEs in soil samples existed mainly as light REEs, and the same concentration distribution patterns of Oddo-Hakins law were observed, showing negative gradient from La to Lu concentrations. The REE contents in plants were very low, less than 20μg/g and varied with plant species. Apart from rape leaf(Brassica juncea), the REE distribution patterns in other plant leaves were consistent with soils, indicating that these plants generally absorbed REEs from soil without selectivity. Rape leaf showed selective absorption for LREEs, especially for La. The REE concentration distribution in parts of hot pepper(Capsicum annuum) was characteriaed by root>leaf>stem>fruit. The REEs absorbed by hot pepper concentrated mainly in roots and leaves, very little migrated into fruit. Transfer factors(TFs) of REEs in plants were very low. Although the contents of LREEs were relatively more than those of HREEs, no distinct difference of TFs between LREEs and HREEs was observed, meaning that LREEs and HREEs have the same abilities of transportation. However, for rape leaf, the TFs of LREEs were one or two orders of magnitude higher than those of HREEs.     

Electrochemical study of glassy carbon electrodes modified with zirconium phosphate and some azine-type redox dyes

Glassy carbon (GC) electrodes were modified with a layer of zirconium phosphate (ZrP), using either direct chemical synthesis onto the surface or a ZrP gel droplet evaporation procedure. The azine-type dyes nile blue A (NB) and toluidine blue O (TB) were immobilized onto the ZrP-modified GC electrodes either by adsorption onto just the formed layer of ZrP or by inclusion into the ZrP matrix during its chemical synthesis. The electrochemical behavior of the GC·ZrP·dye composite electrodes was studied. For GC·ZrP-modified electrodes prepared by chemical synthesis on the surface, coverage by NB or TB of one or a few monolayers was found, with E _m values for these redox couples slightly shifting by ca. 0.05 V to the negative direction. For the GC·ZrP electrodes prepared by gel droplet evaporation, the E _m values for NB and TB appear initially shifted by ca. 0.2 V to the positive direction; however, both cathodic and anodic peaks return to their usual positions on the potential scale during soaking these electrodes in a buffer solution. Electronic Publication     

Electrochemical behaviour of gold, silver, platinum and palladium on the glassy carbon electrode modified by chitosan and its application

The chitosan-modified glassy carbon electrode can be used as a working electrode for the determination of precious metal elements: Au, Ag, Pt, Pd. In low pH medium, the complex anions of these precious elements combine with the protonated group ---NH₃⁺ in the chitosan molecule in the form of an ion-association complex. These metal ions were selectively enriched and we got sensitive anodic stripping current. These elements content in ore, welding material have been determined by this method. The results were consistent with those from standard sample and ICP atomic emission spectrometry method. The possible mechanism of electrochemical reaction has been proposed by the study of CV, UV and FT-Raman spectrometry.     

Electro-oxidation of herbicide halosulfuron methyl on glassy carbon electrode and applications

Halosulfuron methyl, a fast-acting herbicide and is absorbed into leaf tissue within 1-2 days and translocated through the vascular system, interrupting amino acid production within the plant, can be detected using glassy carbon electrode the technique of adsorptive stripping voltammetry. The adsorptive stripping voltammetric behavior of halosulfuron methyl was investigated in pH range 1.0-10.0. Halosulfuron methyl was irreversibly oxidized at a glassy carbon electrode. Electrochemical techniques including adsorptive stripping voltammetry and cyclic voltammetry were employed to study the oxidation mechanism. The experimental parameters such as the accumulation potential, accumulation time and frequency were optimized. The linear range, detection limit and quantification for halosulfuron methyl were evaluated by adsorptive stripping voltammetry. Under the optimized conditions, the peak current is linear to halosulfuron methyl concentration in the range 4.1-50.0 μg mL⁻¹. Limit of detection and limit of quantification were 1.23 and 4.10 μg mL⁻¹, respectively. The interference of inorganic species and other some pesticides on the voltammetric response have been studied. The applicability to spiked soil and natural water was described and the recoveries for the standards added are 103.8% and 108.2%, respectively. The method is successfully applied for the determination of halosulfuron methyl in commercial formulation.     

对苯二酚在碳纳米管修饰玻碳电极的电化学行为及电化学动力学研究

碳纳米管(Carbon Nanotubes,CNT)自1991年发现以来,因其结构所具有的高比表面,高电导率,稳定的化学性质与超常的机械强度已成为世界范围内的研究热点,并应用于催化、气体储藏和电极材料等领域。用CNT修饰的电极具有良好的电化学性能并且已经取得了很好的实验结果[1],因此研究碳     

番红花红聚合膜修饰电极及其应用

研究了番红花红(SFR)在玻碳电极表面聚合过程及聚合条件。SFR聚合膜对于肾上腺素(EP)的氧化能够起到明显的电催化作用。分别利用循环伏安法(CV)、差分脉冲法(DPV)、计时电流法研究了EP在pH7.4的磷酸缓冲溶液中的线性关系,发现其浓度分别在2.0×10-6～9.0×10-6mol/L、1.0×10-5～1.0×10-3mol/L(CV),2.0×10-5～4.0×10-4mol/L(DPV),2.0×10-6～5.0×10-6mol/L(计时电流法)范围内呈良好的线性关系,该电极已用于实际样品测定。     

以OT为底物固体电极伏安法测定辣根过氧化物酶及其标记物的研究

以玻碳电极为工作电极研究了邻联甲苯胺(OT)为底物微分脉冲伏安法测定辣根过氧化物酶(HRP)及其标记物的方法。HRP能够催化H2O2氧化OT,其反应产物在玻碳电极上-0.58V(vs.Ag/AgCl)左右被还原产生一个灵敏的还原峰,还原峰电流随着酶浓度的增大而增大,借助此还原电流可以测定HRP,并进而可用于以HRP为标记物的酶免疫分析。对酶催化反应条件和酶催化反应产物的测定条件进行了详细的研究,在最佳实验条件下测定游离HRP的线性范围是2.0×10-9～4.0×10-8g/mL,检出限为1.6×10-9g/mL;测定游离的酶标记物(IgG HRP),稀释范围为1∶2000～1∶400000,最大稀释比为1∶400000。     

对硝基苯酚在多壁碳纳米管修饰玻碳电极上的电化学行为及分析测定

水中对硝基苯酚主要来源于化工、制药行业,它有致癌作用。人们已对它的测定方法进行了大量的研究,最早采用的测定方法是分光光度法,其检测限偏高;色谱法测定对硝基苯酚,操作繁琐,仪器昂贵,分析成本高。后来又发展了一种操作更方便的直接用于测定的电化学方法。本文旨在利用碳纳米管对对硝基苯酚的吸附性能,研究对硝基苯酚在多壁碳纳米管修饰电极上的电化学行为。     

聚精氨酸修饰玻碳电极上多巴胺的电化学特性及其检测

用循环伏安法制备了聚精氨酸修饰玻碳电极,研究了神经递质多巴胺在该聚合物薄膜修饰电极上的电化学行为及其检测。在pH7.0的磷酸盐缓冲溶液中,多巴胺在聚精氨酸修饰电极上于0.19V和0.16V处出现一对灵敏、可逆的氧化还原峰。在最佳测试条件下,氧化峰电流与多巴胺的浓度在3.0×10-7~8.0×10-4mol/L范围内呈良好的线性关系,线性回归方程为Ipa(μA)=86.063C(mmol/L) 20.183,相关系数r=0.9993,最低检测限(3σ)5.0×10-8mol/L。用于多巴胺针剂含量的测定,结果满意。     

Electrochemical determination of naproxen in the presence of acetaminophen using a carbon paste electrode modified with activated carbon nanoparticles

In this study, cyclic voltammetry and differential pulse voltammetry were used to determine the electrochemical properties and concentration of naproxen in pharmaceutical formulation and human serum samples by using a carbon paste electrode modified with activated carbon nanoparticles. Optimum conditions were obtained at an electrode with 0.005 g activated carbon nanoparticles in a phosphate buffer solution of pH 6 as a supporting electrolyte. Linear calibration curves were obtained in the range of 0.1–120 μM, and the detection limit of naproxen determined was 0.0234 μM. The modified electrode shows good selectivity for naproxen in the presence of some organic and inorganic interferences and very good precision in real samples. Finally, naproxen was measured in the presence of acetaminophen.     

Electrochemical behavior and voltammetric determination of tryptophan based on 4-aminobenzoic acid polymer film modified glassy carbon electrode

Herein, a novel electrochemical method was developed for the determination of tryptophan based on the poly(4-aminobenzoic acid) film modified glassy carbon electrode (GCE). The electrochemical behaviors of tryptophan at the modified electrode were investigated. It was found that the oxidation peak current of tryptophan at the modified GCE was greatly improved compared with that at the bare GCE. The effects of supporting electrolyte, pH value, scan rate, accumulation potential and time were examined. The oxidation peak current of tryptophan was proportional to its concentration over the range from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹. The limit of detection was evaluated to be 2.0 × 10⁻⁷ mol L⁻¹. The proposed method was sensitive and simple. It was successfully employed to determine tryptophan in pharmaceutical samples.     

Electrochemical determination of malachite green using a multi-wall carbon nanotube modified glassy carbon electrode

A multi-wall carbon nanotube (MWNT) film-modified electrode is described for the determination of malachite green (MG). The electrochemical profile of MG was examined using cyclic voltammetry (CV) and differential pulse voltammetry (DPV), suggesting that the MWNT film facilitates the electron transfer of MG in terms of a potential shift and then significantly enhances the oxidation peak current of MG. The experimental parameters, such as supporting electrolyte, thickness of MWNT film, scan rate and accumulation time, were optimized. Consequently, a sensitive and convenient electrochemical method is proposed for the determination of MG. The oxidation peak current is proportional to the concentration of MG over the range from 5.0 × 10⁻⁸ to 8.0 × 10⁻⁶ mol L⁻¹ obeying the following equation: i_p = 0.09 + 1.19 × 10⁷ C (r = 0.995, i_p in μA, C in mol L⁻¹). The detection limit is 6.0 × 10⁻⁹ mol L⁻¹ (signal to noise = 3) after 5 min of accumulation. Moreover, this method possesses good reproducibility (RSD is 5.6%, n = 8) as well as long-term stability. Finally, the new method was employed to determine MG in fish samples. Correspondence: W. Huang, Department of Chemistry, Hubei Institute for Nationalities, Enshi 445000, P.R. China     

丁香酚在改性蒙脱土修饰电极上的电化学行为及测定

制备了十八烷基三甲基溴化铵( STMAB)改性蒙脱土修饰电极,用循环伏安法和差分脉冲伏安法(DPV)研究了丁香酚在该电极上的电化学行为.在pH6.0 PBS电解液中,丁香酚在该电极上的电极反应受扩散控制,转移电子数等于质子数n=m=2,电极有效面积Aeff=0.034cm2,扩散系数D =2.58×10-6cm2/s....     

Electroanalytical investigation and determination of pefloxacin in pharmaceuticals and serum at boron-doped diamond and glassy carbon electrodes

The anodic behavior and determination of pefloxacin on boron-doped diamond and glassy carbon electrodes were investigated using cyclic, linear sweep, differential pulse and square wave voltammetric techniques. In cyclic voltammetry, pefloxacin shows one main irreversible oxidation peak and additional one irreversible ill-defined wave depending on pH values for both electrodes. The results indicate that the process of pefloxacin is irreversible and diffusion controlled on boron-doped diamond electrode and irreversible but adsorption controlled on glassy carbon electrode. The peak current is found to be linear over the range of concentration 2 × 10⁻⁶ to 2 × 10⁻⁴ M in 0.5 M H₂SO₄ at about +1.20 V (versus Ag/AgCl) for differential pulse and square wave voltammetric technique using boron-doped diamond electrode. The repeatability, reproducibility, precision and accuracy of the methods in all media were investigated. Selectivity, precision and accuracy of the developed methods were also checked by recovery studies. The procedures were successfully applied to the determination of the drug in pharmaceutical dosage forms and humans serum samples with good recovery results. No electroactive interferences from the excipients and endogenous substances were found in the pharmaceutical dosage forms and biological samples, respectively.     

Electrochemical behavior and voltammetric determination of norfloxacin at glassy carbon electrode modified with multi walled carbon nanotubes/Nafion

A simple and rapid electrochemical method is developed for the determination of trace-level norfloxacin, based on the excellent properties of multi-walled carbon nanotubes (MWCNTs). The MWCNTs/Nafion film-coated glassy carbon electrode (GCE) is constructed and the electrochemical behavior of norfloxacin at the electrode is investigated in detail. The results indicate that MWCNTs modified glassy carbon electrode exhibited efficiently electrocatalytic oxidation for norfloxacin (NFX) with relatively high sensitivity, stability and life time. Under conditions of cyclic voltammetry, the current for oxidation of selected analyte is enhanced significantly in comparison to the bare GCE. The electrocatalytic behavior is further exploited as a sensitive detection scheme for the analyte determinations by linear sweep voltammetry (LSV). Under optimized condition in voltammetric method the concentration calibration range and detection limit (S/N=3) are 0.1-100 micromol/L and 5 x 10(-8)mol/L for NFX. The proposed method was successfully applied to NFX determination in tablets. The analytical performance of this sensor has been evaluated for detection of the analyte in urine as a real sample.     

没食子酸在电活化玻碳电极上的电化学行为及测定

采用循环伏安法和线性扫描伏安法对没食子酸在电活化玻碳电极上的电化学行为进行了研究。玻碳电极在pH7.0的磷酸盐缓冲溶液中,用恒电位法在1.7 V电位阳极氧化400 s。然后在pH3.0的柠檬酸盐缓冲溶液中,没食子酸在0.479 V和0.442 V处有一良好的氧化还原峰,在0.02～0.40 V s-1范围内,其氧化峰电流与扫描速率呈良好线性关系,表明电极过程为受吸附控制的准可逆过程。线性循环伏安法的氧化峰电流与没食子酸浓度1×10-6～1×10-4mol L-1范围内呈良好的线性关系(r=0.980 6),检出限为7.6×10-7mol L-1(S/N=3)。该方法操作简便,重现性较好,并应用此法分析了健民咽喉片剂中的没食子酸的含量。