Amperometric and spectrophotometric determination of carbaryl in natural waters and commercial formulations

The work presented describes the development and evaluation of two flow-injection analysis (FIA) systems for the automated determination of carbaryl in spiked natural waters and commercial formulations. Samples are injected directly into the system where they are subjected to alkaline hydrolysis thus forming 1-naphthol. This product is readily oxidised at a glassy carbon electrode. The electrochemical behaviour of 1-naphthol allows the development of an FIA system with an amperometric detector in which 1-naphthol determination, and thus measurement of carbaryl concentration, can be performed. Linear response over the range 1.0×10^–7 to 1.0×10^–5 mol L^–1, with a sampling rate of 80 samples h^–1, was recorded. The detection limit was 1.0×10^–8 mol L^–1. Another FIA manifold was constructed but this used a colorimetric detector. The methodology was based on the coupling of 1-naphthol with phenylhydrazine hydrochloride to produce a red complex which has maximum absorbance at 495 nm. The response was linear from 1.0×10^–5 to 1.5×10^–3 mol L^–1 with a detection limit of 1.0×10^–6 mol L^–1. Sample-throughput was about 60 samples h^–1. Validation of the results provided by the two FIA methodologies was performed by comparing them with results from a standard HPLC–UV technique. The relative deviation was <5%. Recovery trials were also carried out and the values obtained ranged from 97.0 to 102.0% for both methods. The repeatability (RSD, %) of 12 consecutive injections of one sample was 0.8% and 1.6% for the amperometric and colorimetric systems, respectively.     

Multicommuted flow-through fluorescence optosensor for determination of furosemide and triamterene

Multicommutation implemented with flow-through optosensors is a very promising area of research. This recent approach benefits from the advantages of both methods and results in high sensitivity, selectivity, and speed, and little waste generation. This paper reports the simultaneous determination of furosemide and triamterene, two widely used diuretics, by measurement of their native fluorescence. The system has been proved to be useful for determination of both analytes in pharmaceutical preparations and for determination of triamterene in human urine and serum. A minicolumn filled with Sephadex SPC-25 microbeads was used to achieve separation of both analytes before detection in a flow-through cell filled with the same resin. The sensor is linear in the range 50–1200 and 0.4–8 ng mL⁻¹ with detection limits of 15 and 0.1 ng mL⁻¹ for furosemide and triamterene, respectively.     

Cyclodextrin-enhanced fluorescence and photochemically-induced fluorescence determination of five aromatic pesticides in water

The effect of β-cyclodextrin (β-CD) and hydroxypropyl-β-cyclodextrin (HP-β-CD) aqueous solutions upon the fluorescence and photochemically-induced fluorescence (PIF) properties of five pesticides, including coumatetralyl, pirimiphos-methyl, chlorpyriphos, deltamethrin and fenvalerate was investigated. A 1:1 stoichiometry was found for the β-CD and HP-β-CD complexes formed with all compounds. Binding constant values, ranging between about 90 and 830 M⁻¹ were calculated using the iterative nonlinear least-squares regression approach. Cyclodextrin-enhanced fluorescence and PIF methods were developed for the determination of these pesticides with linear dynamic ranges over two orders of magnitude, and limits of detection (LOD) between 0.2 and 54 ng ml⁻¹ according to the compound. Application to the analysis of tap water and river water samples yielded satisfactory recoveries (88–116%). The method seems to be suitable for environmental water analysis.     

Flow-injection determination of hydrogen peroxide based on fluorescence quenching of chromotropic acid catalyzed with Fe(II)

Flow-injection analysis system (FIA system), which was based on Fe(II)-catalyzed oxidation of chromotropic acid with hydrogen peroxide, was developed for the determination of hydrogen peroxide. The chromotropic acid has a fluorescence measured at λ_em = 440 nm (emission wavelength) with λ_ex = 235 nm (excitation wavelength), and the fluorescence intensity at λ_em = 440 nm quietly decreased in the presence of hydrogen peroxide and Fe(II), which was caused by Fe(II)-catalyzed oxidation of chromotropic acid with hydrogen peroxide. By measuring the difference of fluorescence intensity, hydrogen peroxide (1.0 × 10⁻⁸-1.0 × 10⁻³ mol L⁻¹) could be determined by the proposed FIA system, whose analytical throughput was 40 samples h⁻¹. The relative standard deviation (RSD) was 1.03% (n = 10) for 4.0 × 10⁻⁸ mol L⁻¹ hydrogen peroxide. The proposed FIA technique could be applied to the determination of hydrogen peroxide in rain water samples.     

Flow amperometric determination of carbofuran and fenobucarb

Abstract

The sorption of pentachlorophenol (PCP) onto the aquatic humic matter (HM) for very wide concentration range (60 ng PCP/L - 1 mg PCP/L) was investigated. The binding affinity increased significantly with the acidity of the solution. The dissolved organic carbon (DOC) normalized sorption coefficients (log K_OC) of PCP were 3.39 at pH 3, 3.19 at pH 5.5 and 3.01 at pH 7. The binding of PCP took place via a two step binding mechanism: the rapid first step was followed by a second much slower one indicating that the surface of the HM is very heterogeneous containing binding sites with different binding affinities. It was possible to obtain a “fully saturated” HM-PCP adduct (also all possible micro-voids of the HM were occupied) in a very high PCP concentration. The log K_OC value for the whole concentration range was slightly smaller than that obtained under very low PCP concentration level. The Langmuir isotherm was the most suitable for the whole concentration range of PCP, whereas the Freundlich model was the most suitable for the low concentration range of PCP. The dissimilarities between different sorption models were as a whole marginal and thus it is possible without significant loss of information to describe the PCP sorption with a linear model. The results verify that the conventional humic (HA) and fulvic (FA) acid type humic solutes of fresh waters account for the main part of the PCP sorption.     

Sensing of trace amounts of cadmium in drinking water using a single fluorescence-based optosensor

In this work, a single solid surface fluorescence based flow-through optosensor has been developed for the determination of trace amounts of cadmium in drinking water samples. The developed methodology is based on the transient immobilization of the target species on an appropriate active solid sensing zone (Sephadex QAE-A25).The target species was the fluorogenic chelate, formed as a result of the on-line complexation of Cd (II) with 8-hydroxyquinoline-5-sulfonic acid, being its fluorescence signal continuously monitored at an emission wavelength of 520 nm upon excitation at 360 nm. The effect of instrumental, chemical and flow-injection variables on the fluorescence signal were carefully investigated. Under optimized conditions, the proposed optosensor was calibrated in the range 2-60 μg l^− 1, obtaining a detection limit of 0.48 μg l^− 1, and a R.S.D of 1.9%, with a sampling frequency of 18 h^− 1. The proposed method was satisfactorily applied to different drinking water samples, with recoveries between 97% and 104%. Simplicity, low cost and easy operation are the main and more remarkable features of the proposed procedure.     

Determination of organophosphate and carbamate pesticides based on enzyme inhibition using a pH-sensitive fluorescence probe

A flow injection system for the determination of organophosphate and carbamate pesticides is described. A sensitive fluorescence probe was synthesized and used as the pH indicator to detect the inhibition of the enzyme acetylcholinesterase (AChE). The percentage inhibition of enzyme activity is correlated to the pesticide concentration. Several parameters influencing the performance of the system are discussed. The detection limits of 3.5, 50, 12 and 25 μg/l for carbofuran, carbaryl, paraoxon and dichlorvos, in pure water, respectively were achieved with an incubation time of 10 min. A complete cycle of analysis, including incubation time, took 14 min. The detection system has been applied to the determination of carbofuran in spiked vegetable juices (Chinese cabbage and cole), achieving recovery values between 93.2 and 107% for Chinese cabbage juice and 108 and 118% for cole juice at the different concentration levels assayed.     

Simple flow-injection system for the simultaneous determination of nitrite and nitrate in water samples

A novel spectrophotometric reaction system was developed for the determination of nitrite as well as nitrate in water samples, and was applied to a flow-injection analysis (FIA). The spectrophotometric flow-injection system coupled with a copperised cadmium reductor column was proposed. The detection was based on the nitrosation reaction between nitrite ion and phloroglucinol (1,3,5-trihydroxybenzene), a commercially available phenolic compound. Sample injected into a carrier stream was split into two streams at the Y-shaped connector. One of the streams merged directly and reacted with the reagent stream: nitrite ion in the samples was detected. The other stream was passed through the copperised cadmium reductor column, where the reduction of nitrate to nitrite occurred, and the sample zone was then mixed with the reagent stream and passed through the detector: the sum of nitrate and nitrite was detected. The optimised conditions allow a linear calibration range of 0.03–0.30 μg NO₂⁻-N ml⁻¹ and 0.10–1.00 μg NO₃⁻-N ml⁻¹. The detection limits for nitrite and nitrate, defined as three times the standard deviation of measured blanks are 2.9 ng NO₂⁻-N ml⁻¹ and 2.3 ng NO₃⁻-N ml⁻¹, respectively. Up to 20 samples can be analyzed per hour with a relative standard deviation of less than 1.5%. The proposed method could be applied successfully to the simultaneous determination of nitrite and nitrate in water samples.     

Flow-through optosensor combined with photochemically induced fluorescence for simultaneous determination of binary mixtures of sulfonamides in pharmaceuticals, milk and urine

A sensitive and selective flow-through optosensor implemented with photochemically induced fluorescence (PIF) is proposed for the simultaneous determination of mixtures sulfamethoxazole/sulfanilamide and sulfathiazole/sulfanilamide. The resolution was accomplished by placing in the flow system a minicolumn filled with an appropriate solid support. Whereas one of the sulfonamides is not retained in the minicolumn and is determined by measuring its native fluorescence on the solid surface of the sensing microbeads in the detection area, the other one is retained and, after its elution, it is photochemically converted into a strongly fluorescent photoproduct which is transitorily retained on the sensing support in the flow cell and monitored. Linear calibration graphs were obtained over a concentration range of 2–3 orders of magnitude. The detection limits for the determination of sulfamethoxazole, sulfanilamide and sulfathiazole are 8.1, 2.9 and 5.7 ng mL⁻¹, respectively. The method was applied to pharmaceuticals, milk and human urine. The recovery of sulfamethoxazole from pharmaceuticals was 102.5% indicating no interference from trimethoprim which is not photochemically active. The recoveries for urine and milk samples fortified with sulfonamides at levels between 0.1 and 0.7 μg mL⁻¹ agreed within 95.0–107.5% of spiked levels.     

A novel flow-through fluorescence optosensor for the sensitive determination of tetracycline

A flow-through fluorescence optosensor with Sephadex G-50 microbeads as solid support is developed for the sensitive determination of tetracycline (TC). The fluorescent TC derivative encapsulated in CTAB micelle structures is retained onto the surface of the microbeads packed into a fluorescent flow cell in a flow system, followed by measurement of the native fluorescence of the TC derivative on the bead surface. The retained TC derivative is easily stripped off with DI water from the bead surface by breaking-down the micelle structure. This offers a convenient and effective way for the regeneration of the used solid support with DI water as a carrier. Under the optimal conditions, a linear calibration graph is obtained within a range of 3-500 μg L⁻¹, along with a detection limit of 1.0 μg L⁻¹. The present solid surface fluorescence optosensor provides a 22-fold improvement on the detection sensitivity for TC in comparison with that derived by fluorescence detection in aqueous medium. The feasibility of this flow-through fluorescence optosensor is evaluated by analyzing TC in a commercial drug tablet and surface water samples.     

支撑液膜在线萃取富集流动注射荧光光度法测定水中痕量苯酚

选用无毒性的磷酸三丁酯为流动载体, 煤油为膜溶剂的液膜萃取体系, 建立了支撑液膜在线萃取富集流动注射荧光光度法测定水中痕量苯酚的新方法. 对实验条件进行了优化. 方法的检出限为0.4 μg/L, 线性范围为1～180 μg/L.     

A continuous flow system combined with a sensing fluorimetric transductor for the determination of β-naphthol

A single automatic method for continuous flow determination of β-naphthol based on the enhancement of its native fluorescence once the analyte was transitorily retained on-line on a solid support (QAE A-25 resin) is reported. So, a flow-through optosensor was developed using a flow-injection analysis system with solid phase fluorimetric transduction. KCl (0.15 mol l⁻¹) at pH 12.0 was used as carrier solution. To obtain the optimum fluorescence signal the wavelengths chosen were 245 nm (excitation) and 420 nm (emission). The response of the sensor was directly proportional to the sample volume injected in the studied range 40-1500 μl. Approximately one higher order of magnitude is achieved in sensitivity when 1500 μl are used with respect to the use of 40 μl of sample. The sensor was calibrated for three different injection volumes: 40, 600 and 1500 μl, responding linearly in the measuring range of 2-60, 0.5-15 and 0.2-5 μg l⁻¹ with detection limits of 0.5, 0.09 and 0.05 μg l⁻¹, respectively. The relative standard deviation for ten independent determination is 0.6% (40 μl), 0.9% (600 μl) and 2.3% (1500 μl). A recovery study was performed onto three different spiked water samples at concentration levels from 1 to 2.5 μg l⁻¹ and the recovery percentage from the experimental data ranged between 101±2 and 105±5.     

Determination of carbaryl by flow injection with luminol chemiluminescence inhibition detection

A flow-injection procedure is described for the determination of carbaryl based on its inhibition effect on luminol-cobalt(II) chemiluminescence reaction in alkaline medium in the presence of hydrogen peroxide. The calibration data over the range 5.0?×?10^?7 to 20?×?10^?6?M give a correlation coefficient (r ²) of 0.9972 with relative standard deviations (RSD; n?=?4) in the range of 1.0–2.1% with a limit of detection (3?×?blank noise) of 2.37?×?10^?7?M for carbaryl. The sample throughput was 120?h^?1. The effects of some carbamates, anions, and cations were studied on luminol CL system for carbaryl determination. The proposed method has been applied to determine carbaryl in natural waters.     

Simple and rapid flow-injection spectrophotometric determination of carbaryl after liquid-liquid extraction

A simple procedure was developed for the spectrophotometric determination of carbaryl and its hydrolysis product 1-naphthol in water. These compounds are extracted into xylene and back-extracted, as the 1-naphtholate, with 0.2 M NaOH. A 600-μl volume of the alkaline extract is injected into a flow analysis manifold which provides the reaction between naphtholate and 50 μg ml⁻¹ p-aminophenol solution in the presence of 0.004 M KIO₄ and spectrophotometric measurement is carried out at 596 nm. The method provides a limit of detection of 26.5 ng ml⁻¹ carbaryl and a sample frequency of 110 injections per hour. Recoveries in different types of matrices vary from 95 to 102%.     

Rapid and simultaneous analysis of dichlorvos, malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid in citrus fruit by flow-injection ion spray ionization tandem mass spectrometry

A simple method for the rapid and simultaneous analysis of dichlorvos (DDVP), malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid (2,4-D) in citrus fruit, which uses flow-injection ion spray ionization tandem mass spectrometry, has been developed for the first time. The method involves the combined use of stable isotopically labeled internal standards (DDVP-d₆, malathion-d₁₀, carbaryl-d₇, and 2,4-D-d₅) and a multiple reaction monitoring technique. The average recoveries for the pesticides at the same concentrations as their tolerance levels (DDVP: 0.1-0.2 μg g⁻¹; malathion: 0.5-4.0 μg g⁻¹; carbaryl: 1.0 μg g⁻¹; 2,4-D: 1.0-2.0 μg g⁻¹) ranged from 90 to 119% with the relative standard deviation (R.S.D.) ranging from 1.0 to 13.1% (n = 5). Analysis time, including sample preparation and determination, was only 15 min. The present method is effective for screening DDVP, malathion, carbaryl, and 2,4-D in citrus fruit.     

乳酸的液态酶荧光毛细分析法研究

基于乳酸脱氢酶(LDH)和烟酰胺腺嘌呤二核苷酸(NADH)氧化还原体系,提出了乳酸的液态酶荧光毛细分析方法(LE-FCA).在激发波长350nm、发射波长460nm奈件下,用LE-FCA法对乳酸进行了测定;其线性范围为0.2～1.0 mmol/L,r>0.9932,检出限为0.022 mmol/L,RSD<4.2%.LE-FCA能节省贵重的酶试剂,样品用量仅为18μL;可用于医药、卫生、工业、食品等含乳酸样品的测定.     

The determination of atmospheric concentrations of the active ingredients of pesticide formulations by high-performance liquid chromatography

Summary Methods of sampling atmospheres contaminated by pesticides in factory and agricultural environments, and subsequent analysis by HPLC, are discussed. Air sampling is carried out using porous polymer or filter collection media, usually a 100 dm³ air volume is suitable. Detection limits with ultra-violet detection are in the range 0.1 to 10 g m^–3.Presented at the 14th International Symposium on Chromatography London, September, 1982     

Native fluorescence flow-through optosensor for the fast determination of diphenhydramine in pharmaceuticals.

A single, rapid flow-through optosensor spectrofluorometric system is proposed for the determination of diphenhydramine in different pharmaceutical preparations. This sensor was developed in conjunction with a monochannel flow-injection analysis system with fluorometric solid-phase transduction. Diphenhydramine was directly injected into a carrier stream of ethanol/water, 50% (v:v), and transitorily retained on a sorption gel Sephadex G-15 placed in the detection area into the cell. The determination was carried out without any derivatization reaction by directly measuring the intrinsic fluorescence of the analyte and using the peak height as an analytical signal. The chemical and instrumental variables were optimized, and the influence of some foreign substances that can be found in typical pharmaceutical samples containing diphenhydramine was also investigated. Diphenhydramine could be determined in the concentration ranges of 0.5 - 8 microg ml(-1) and 0.1 - 1.2 microg ml(-1) with detection limits of 0.088 and 0.019 microg ml(-1) at sampling rates of 30 and 19 h(-1) for 200 and 800 microl of the sample volume, respectively.     

Quartz crystal microbalance determination of organophosphorus and carbamate pesticides

We have developed a quartz crystal microbalance (QCM) biosensor for the determination of organophosphorus and carbamate pesticides. A change in resonant frequency is observed as a result of mass adsorption, and we have used this as the basis for sensor development. Specifically, we have used a two-enzyme system (acetylcholine-esterase and choline oxidase) which converts acetylcholine to betaine producing hydrogen peroxide as a by-product. In a third enzyme reaction (peroxidase), the peroxide is able to oxidise benzidines (3,3′-diaminobenzidine) into an insoluble product that precipitates out and can adsorb to surfaces. Non-ionic surfactants have been used for the first time to enhance the surface deposition of suspended precipitate, thereby improving sensor sensitivity. Pesticides are known to inhibit esterase activity (thereby reducing the amount of QCM-detectable precipitate produced). We have shown that the QCM-enzyme sensor system can be used to determine carbaryl and dichlorvos down to 1 ppm.