超声化学法制备纳米WO3掺杂聚苯乙烯及其表征

 为了满足惯性约束聚变和电磁内爆实验对靶材料的需求，以W(CO)_{5/sub>为原料，利用超声化学法在线制备纳米WO3/sub>掺杂聚苯乙烯。所得样品用TEM，XPS，FTIR和TG进行了表征。测试结果表明，钨元素主要以WO3/sub>的形态存在，WO3/sub>粒径分布为20~50 nm，WO3/sub>微粒被聚苯乙烯完全包覆，掺杂后聚苯乙烯的热稳定性提高了70 ℃。在此基础上，对超声化学法的反应机理进行了探讨。研究表明：纳米WO3/sub>与聚苯乙烯分子链有一定的化学键结合，纳米WO3/sub>在聚苯乙烯基体中分布均匀。}     

超声化学法制备纳米WO3掺杂聚苯乙烯及其表征

为了满足惯性约束聚变和电磁内爆实验对靶材料的需求,以W(CO)5/sub>为原料,利用超声化学法在线制备纳米WO3/sub>掺杂聚苯乙烯。所得样品用TEM,XPS,FTIR和TG进行了表征。测试结果表明,钨元素主要以WO3/sub>的形态存在,WO3/sub>粒径分布为20~50 nm,WO3/sub>微粒被聚苯乙烯完全包覆,掺杂后聚苯乙烯的热稳定性提高了70 ℃。在此基础上,对超声化学法的反应机理进行了探讨。研究表明：纳米WO3/sub>与聚苯乙烯分子链有一定的化学键结合,纳米WO3/sub>在聚苯乙烯基体中分布均匀。     

Ultrasound and ionic-liquid-assisted synthesis and characterization of polyaniline/Y2O3 nanocomposite with controlled conductivity

A sonochemical method has been employed to prepare polyaniline-Y₂O₃ nanocomposite with controlled conductivity with the assistance of an ionic liquid (IL). Ultrasound energy and the IL replace conventional oxidants and metal complexes in promoting the polymerization of aniline monomer for the first time. Structural characterization has revealed that the resulting nanocomposite consists of microspheres of average diameter 3–5 μm. The products were found to consist of regular solid microspheres covered with some 40 nm nanoparticles. Under certain polymerization conditions, polyaniline nanofibers and nanosheet were obtained. The method may open a new pathway for the preparation of nanoscale conducting polymer nanocomposites with the aid of ILs. The conductivity of the product varies with the mass ratio of aniline monomer to Y₂O₃ and IL. TG curves of the products suggest that the thermal degradation process of the PANI/Y₂O₃ composites proceeds in two steps and that the composites are more thermally stable than pure PANI. The reaction conditions have been optimized by varying parameters such as the aniline/Y₂O₃ ratio and the type and amount of IL used. The effect of the ultrasonic irritation time and frequency on the morphology, conductivity and yield were discussed.     

Colloid electrostatic self-assembly synthesis of SnO2/graphene nanocomposite for supercapacitors

Journal of Nanoparticle Research - Most anticancer drugs cannot kill cancer stem cells (CSCs) effectively, which lead to the failure of anticancer chemotherapy, such as relapse and metastasis. In...     

Direct pyrolysis and ultrasound assisted preparation of N,S co-doped graphene/Fe3C nanocomposite as an efficient electrocatalyst for oxygen reduction and oxygen evolution reactions

Bifunctional electrocatalysts to enable efficient oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are essential for fabricating high performance metal–air batteries and fuel cells. Here, a defect rich nitrogen and sulfur co-doped graphene/iron carbide (NS-GR/Fe₃C) nanocomposite as an electrocatalyst for ORR and OER is demonstrated. An ink of NS-GR/Fe₃C is developed by homogeneously dispersing the catalyst in a Nafion containing solvent mixture using an ultrasonication bath (Model-DC150H; power − 150 W; frequency − 40 kHz). The ultrasonically prepared ink is used for preparing the electrode for electrochemical studies. In the case of ORR, the positive half-wave potential displayed by NS-GR/Fe₃C is 0.859 V (vs. RHE) and for the OER, onset potential is 1.489 V (vs. RHE) with enhanced current density. The optimized NS–GR/Fe₃C electrode exhibited excellent ORR/OER bifunctional activities, high methanol tolerance and excellent long-term cycling stability in an alkaline medium. The observed onset potential for NS–GR/Fe₃C electrocatalyst is comparable with the commercial noble metal catalyst, thereby revealing one of the best low-cost alternative air–cathode catalysts for the energy conversion and storage application.     

Fabrication and characterization of Au/SiO2 nanocomposite films

Au/SiO₂ nanocomposite films were prepared by radio frequency sputtering technique and annealing. The above nanocomposite films were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and atomic force microscopy (AFM). The surface of the nanocomposite films was uniform with the particle diameter of 100-300 nm. The size of Au crystallites increased on increasing annealing time. The luminescent behavior of the nanocomposite films was characterized by photoluminescence (PL) with different excitation wavelengths. Two emission peaks at around 525 nm and 560 nm were observed with the excitation wavelength at 325 nm. An intensive emission peak at around 325 nm was observed with the excitation wavelength at 250 nm, which is related to the defective structure of the amorphous SiO₂ layer because of oxygen deficiency, and could be applied to many fields, such as ultraviolet laser and ultraviolet detector.     

ZnO/ZrO2 nanocomposite: Sonosynthesis,characterization and its application for wastewater treatment

ZnO/ZrO₂ nanocomposites with different ZnO: ZrO₂ molar ratios (2:1, 1:1, and 1:2)were prepared by sol gel approach under ultrasonic irradiation. For preparation of the nano-composites, the ZnO gel was directly incorporated into the ZrO₂ gel at different molar ratios. The reaction mixture was stirred continuously for two days and then it was ultrasonoicated for 30 min. The filtrated composite gel was washed, and then calcinated at 300 °C in furnace for 3 h. X-ray powder diffraction patterns exhibited well-formed crystal structures and pure crystalline phases in the synthesized nanoparticles (NPs). The FT-IR analyses indicated that the positions of peaks related to Zn-O and Zr-O absorption bands did not change in nano-composites. In addition, FESEM images indicated uniform spherical morphology of the NPs. The highest photo-degradation performance of Congo red (as a model water pollutant) was obtained by 1:2molar ratio of ZrO₂: ZnO in the nano-composite. The particle size and band gap were considered as important factors on nano-catalysts performance. Furthermore, the effects of ultrasonic irradiation, pH, and the concentration of pollutant in solution were investigated on photocatalytic performance of optimum nanocomposite.     

Surface characterization of the Zn-Ni-Al2O3 nanocomposite coating fabricated under ultrasound condition

Zn-Ni-Al₂O₃ nanocomposite coating, which was fabricated by eletrodeposition technique with the aid of ultrasound, was investigated by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis and X-ray photoelectron spectroscopy (XPS). The results reveal that 7.2 wt.% nano-alumina particles uniformly dispersed in the matrix of the composite coating. The XPS analyses demonstrate that the outermost layer of Zn-Ni-Al₂O₃ coating was composed of nano-alumina and Zn(OH)₂, while the transition layer between the outermost layer and the Zn-Ni matrix consisted of nano-alumina, metallic Zn, ZnO and metallic Ni. In order to investigate the influences of ultrasonic agitation and the incorporation of nano-alumina on the composition and surface structure of Zn-Ni matrix, the comparison studies of Zn-Ni-Al₂O₃ nanocomposite coating with Zn-Ni coatings fabricated with and without ultrasound were conducted. The results indicate that ultrasonic agitation resulted in a decrease of Ni content in the Zn-Ni matrix and an increase of the thickness of surface oxide layer; while the incorporation of nano-α-Al₂O₃ increased the Ni content in the Zn-Ni matrix.     

Novel conducting lithium ferrite/chitosan nanocomposite: Synthesis,characterization, magnetic and dielectric properties

A study on Lithium ferrite/chitosan nanocomposite (LFCN), easily moldable into arbitrary shapes, as the conducting polymer and ferromagnetic characteristics is presented. The composite material is produced in the presence of Li_0.5Cr_0.1Fe_2.4O₄ and Li_0.5Co_0.1Fe_2.4O₄ nanoparticle by ex-situ polymerizations process. Various characterizations techniques have been used to explore the characteristic of the synthesized products. The frequency dependent dielectric properties and electrical conductivity of all the samples have been measured through complex impedance plot in the frequency range of 1 kHz–6 MHz at room temperature. It was observed that in case of (LFCN), fluctuation in value of (ε′) and (ε″) is ceased over the frequency range of 4 Mz which can be attributed to the steady storage and dissipation of energy in the nanocomposite system. Moreover, it is also observed that electrical conductivity of (LFCN) increases with frequency and its value was found to be (0.032–0.048) (ohm-cm)⁻¹ in frequency range of 1 kHz–6 MHz. Due to its low cost, a simple synthesis process and high flexibility, the proposed LFCN may find applications in various types of electronic components.     

块状Ta2O5-TiO2复合气凝胶的制备与表征

 以乙醇钽、钛酸丁酯为原料,以乙醇为溶剂,通过溶胶-凝胶法及超临界干燥成功制备了Ta₂O₅-TiO₂复合气凝胶。用场发射扫描电镜（SEM）、透射电镜（TEM）、扫描电镜模式下的电子能谱仪（EDS）以及比表面积吸附仪（BET）对其进行表征。结果表明:该气凝胶是由粒径在nm量级的Ti和Ta的羟基氧化物胶体颗粒堆积而成的低密度、高比表积的多孔网络结构材料,孔径分布主要集中在5~15 nm,比表面积为492.9 m²/g,密度为90 mg/cm³左右。     

Synthesis and characterization of ZrO2/MnO2/carbon clusters nanocomposite materials

Nano-sized ZrO₂/MnO₂/carbon clusters composite materials has been successfully obtained by the calcination of a Zr(acac)₄/Mn(acac)₃/epoxy resin complex under an oxygen atmosphere. The compositions of the resulting composite materials were determined using inductively coupled plasma (ICP) spectroscopy, elemental analysis and surface characterization by X-ray diffraction (XRD), scanning electron microscopy and transmission electron microscopy (TEM). The ultraviolet–visible (UV–VIS), X-ray photoelectron spectra (XPS) and electron spin resonance (ESR) spectra of the composites were also measured. ESR spectral examinations suggest the possibility of an electron transfer in the process of MnO₂ → carbon clusters → ZrO₂. The visible light-responsive oxidation–reduction ability of the calcined material was also investigated.     

Electrochemical synthesis and characterization of polyaniline-coated PEMFC metal bipolar plates with improved corrosion resistance

This article reported the electrochemical deposition of polyaniline (PANI) on 316-L stainless steel (316LSS) to improve the anti-corrosion performance as PEMFC metal bipolar plates. The results indicate that PANI can increase the corrosion potential of 316LSS by more than 410.57 mV and effectively decrease the corrosion current density by four orders of magnitude in comparison with the uncoated 316LSS. The experimental results showed that the PANI increased the open-circuit potential of the steel by about 140 mV. The polarization current value of PANI-coated 316LSS reduced to 2.3 × 10^?7 A/cm² under the PEMFC cathode working condition. During exposure for 12 h, Nyquist plots of PANI-coated 316LSS did not change substantially. This indicates that the PANI coating was an effective barrier against the inward penetration of corrosive species.     

Synthesis and characterization of CdS/PVA nanocomposite films

A series CdS/PVA nanocomposite films with different amount of Cd salt have been prepared by means of the in situ synthesis method via the reaction of Cd²⁺-dispersed poly vinyl-alcohol (PVA) with H₂S. The as-prepared films were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) absorption, photoluminescence (PL) spectra, Fourier transform infrared spectroscope (FTIR) and thermogravimetric analysis (TGA). The XRD results indicated the formation of CdS nanoparticles with hexagonal phase in the PVA matrix. The primary FTIR spectra of CdS/PVA nanocomposite in different processing stages have been discussed. The vibrational absorption peak of CdS bond at 405 cm⁻¹ was observed, which further testified the generation of CdS nanoparticles. The TGA results showed incorporation of CdS nanoparticles significantly altered the thermal properties of PVA matrix. The photoluminescence and UV-vis spectroscopy revealed that the CdS/PVA films showed quantum confinement effect.     

负载型复合半导体MoO3-TiO2/SiO2的结构与吸光性能

采用表面改性法制备了负载型复合半导体材料MoO3TiO2/SiO2,用X射线衍射、比表面测定、透射电子显微镜、红外光谱、拉曼光谱、紫外可见漫反射等技术对固体材料的结构进行了表征,并从固体材料的光响应性能和化学吸附性能方面进行了评价.结果表明,MoO3TiO2/SiO2表面存在着高度分散的MoO3和TiO2微晶,它们之间有一定的复合和键联作用,形成了Mo-O-Ti键;MoO3TiO2/SiO2复合材料表面对丙烷分子有化学吸附性能,Mo=O键上的端氧是C3H8的活性吸附位;与本体MoO3和TiO2相比,复合后MoO3TiO2/SiO2的能隙值有所增加,在紫外光区的吸光强度也明显加强,使得光生载流子的复合效率得到抑制,并产生了一定的量子尺度效应.     

Ultrasound-pretreatment combined with Ti3C2-TiO2-AuNPs enhancing the electrogenerated chemiluminescence of the air-saturated luminol for exosomes detection

It is still a great challenge to develop effective strategies to improve the low electrogenerated chemiluminescence (ECL) of air-saturated luminol. Herein, the synergistic effects of Ti₃C₂-TiO₂-AuNPs nano hybrid and high-intensity focused ultrasound pretreatment (ultrasound-pretreatment) were used to significantly improve the ECL emission of the air-saturated luminol, and the mechanism was proposed. The ultrasound-pretreatment as a green method with the cavitation effect could form O₂^–• and H₂O₂ in situ as an initiator. TiO₂ and Au nanoparticles (AuNPs) were in situ decorated on the Ti₃C₂ surface to form Ti₃C₂-TiO₂-AuNPs, and it was proved as a highly efficient booster which could catalyze and aggregate H₂O₂ to the O₂^–•. The utilization rate of intermediates has been greatly improved. Exosomes as model targets can be sensitively detected by the ECL sensor. The detection limit was 195 particles μL⁻¹. The detection results of exosomes in actual samples are satisfactory. We believe that the ultrasound-pretreatment strategy could be extended to the sensitive detection in the biological sample.     

Novel synthesis of highly ordered mesoporous Fe2O3/SiO2 nanocomposites for a room temperature VOC sensor

The controlled synthesis of mesoporous silica and metal oxide nanocomposites with a highly ordered porous structure and large specific surface area for specific applications has been an attractive topic in the field of porous materials. Herein, we introduce a novel method for the fabrication of highly ordered mesoporous structured and large specific surface area Fe₂O₃/SiO₂ nanocomposites, and consider their application in room temperature gas sensors. The mesoporous Fe₂O₃/SiO₂ nanocomposites were synthesised by a two-step method, which combines the hydrothermal growth of Fe₂O₃ nanoparticles and the microemulsion phase of Brij 56 (C₁₆EO₁₀) surfactant as templates in instantly direct-templating synthesis. This synthesis method enables the fabrication of mesoporous Fe₂O₃/SiO₂ nanocomposites without distortion of the ordered porous structure after calcination at high temperature. The synthesised materials were found to be efficient in a room temperature VOC sensor application, with good recovery.     

Synthesis and characterization of novel LiFeBO3/C cathodes for lithium batteries

Carbon-coated LiFeBO₃ has been successfully synthesized by solid state reaction method at 750?°C under Ar atmosphere. Adipic acid was chosen for the source material for carbon during synthesis process. X-ray diffraction pattern confirms the formation of phase with monoclinic structure. Scanning electron microscopic study vindicates the particulate nature of the synthesized LiFeBO₃ with weak agglomeration. Electrochemical impedance spectroscopy parallels the enhanced conducting properties of carbon-coated LiFeBO₃ rather pristine LiFeBO₃. The Li/carbon-coated LiFeBO₃ and LiFeBO₃ cells presented the initial discharge capacities 93 and 47?mAh/g, respectively. After few cycles, the carbon-coated LiFeBO₃ exhibited stable discharge behavior (~53?mAh/g), whereas bare LiFeBO₃ is concerned because poor electrochemical performance has resulted.     

Fabrication and characterization of Au/SiO2 nanocomposite films grown by radio-frequency cosputtering

Au/SiO₂ nanocomposite films were prepared on Si wafers by cosputtering of SiO₂ and gold wires. Au/Si atomic ratios in Au/SiO₂ nanocomposite films were varied from 0.53 to 0.92 by controlling the length of gold wire to study the evolution of the crystallization of gold, the size of Au/SiO₂ nanocomposite particles, and the optical properties of as-deposited Au/SiO₂ nanocomposite films. An X-ray photoelectron spectroscopy reveals that Au exists as a metallic phase in the bulk of SiO₂ matrix. Dome-shaped Au/SiO₂ nanocomposite particles and both Au (1 1 1) and (2 0 0) planes were observed in a field-emission scanning electron microscopy and X-ray diffraction studies respectively. With an ultraviolet-visible, absorption peaks of Au/SiO₂ nanocomposite films were observed at 525 nm.     

Synthesis and characterization of nanocomposite NiO/activated charcoal electrodes for supercapacitor application

Ionics - Nickel oxide (NiO) nanoparticles (NPs) were synthesized at room temperature using coprecipitation method and have been tested as electrode materials by forming composites with activated...     

Preparation and characterization of conducting polymer/silver hexacyanoferrate nanocomposite

In this work, we present an alternative route to prepare silver hexacyanoferrate(II)/polyaniline (PANI) composite thin films. Differently from the electrochemical method, used to synthesize the conducting polymer film on a electrode surface, this new chemical route makes use of dialysis membrane as a solid support to synthesize the silver hexacyanoferrate(III) compound, and subsequently uses this composite membrane as oxidizing agent to polymerize the aniline monomer. The spectroscopic (UV-vis and IR region) and electrochemical characterization (cyclic voltammetry) indicates that the polymeric composite remains optically active and conductive. The X-ray analysis shows that the composite membrane/Ag₃[Fe_III(CN)₆] has an crystalline structure that can be assigned to the Ag₃[Fe_III(CN)₆] structure, and after reaction with aniline solution it became less crystalline. Additionally the SEM measurements shown that the reaction of silver ions with hexacyanoferrate(III) across the membrane results in a well defined and aliened Ag₃[Fe_III(CN)₆] crystals and when this crystalline compound reacts with aniline monomer silver wire of 100 nm of diameter by 6 μm longer are formed together with the conducting polymer polyaniline/Ag_x[Fe_II(CN)₆] composite.