LiNi1/3Co1/3Mn1/3O2 cathode materials for LIB prepared by spray pyrolysis I: the spectral, structural, and electro-chemical properties

Layered lithium ion battery cathode material LiNi_1/3Co_1/3Mn_1/3O₂ with uniform particle size of about 6 μm was synthesized by a spray pyrolysis method. Infrared and X-ray diffraction analyses show that the pyrolysis at 1,000 °C for 2 s in the tube furnace eliminates nearly all the organic components but is still not enough for the complete crystallization of LiNi_1/3Co_1/3Mn_1/3O₂ materials. Therefore, further annealing at 850 °C is needed. The prepared LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials show excellent electrochemical performances. By increasing the C-rates, the cell shows discharge capacities of 159.3, 148.2, 133.7, and 125.7 mAh g^?1 at 0.1, 0.2, 0.5, and 1C rates, respectively. Only 2.1 mAh g^?1 capacity loss is observed when back to 0.1C rate. Moreover, LiNi_1/3Co_1/3Mn_1/3O₂ cathode retains 96, 97.7, 97.1, 94.5, and 97.1 % of its initial discharge capacities after 20 cycles at 0.1, 0.2, 0.5, 1, and back to 0.1C rates, respectively. More than 97 % coulombic efficiencies are observed at all the current densities in 20 cycles.     

Structural and electrochemical properties of LiNi1/3Co1/3Mn1/3O2 material prepared by a two-step synthesis via oxalate precursor

LiNi_1/3Co_1/3Mn_1/3O₂ (LNMCO) powders were formed by a two-step synthesis including preparation of an oxalate precursor by ??chimie douce?? followed by a solid-state reaction with lithium hydroxide. The product was characterized by TG-DTA, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR), Raman spectroscopy, electron spin resonance (ESR), and SQUID magnetometry. XRD data revealed well-crystallized layered LNMCO with ??-NaFeO₂-type structure (R-3?m space group). Morphology studied by SEM and TEM shows submicronic particles of 400?C800?nm with a tendency to agglomerate. The local structure investigated by vibrational spectroscopy (FTIR, Raman), ESR, and SQUID measurements confirms the well-crystallized lattice with a cation disorder of 2.6% Ni²⁺ ions in Li(3b) sites. Electrochemical tests were carried out in the potential range 2.5?C4.5?V vs. lithium metal on samples heated at 900?°C for 12?h. Initial discharge capacity is 154 mAh/g at C/5, while a capacity of 82 mAh/g is still delivered at 10 C by the two-step synthesized LiNi_1/3Co_1/3Mn_1/3O₂ as cathode material.     

Studies of the electrochemical properties and thermal stability of LiNi1/3Co1/3Mn1/3O2/LiFePO4 composite cathodes for lithium ion batteries

A series of LiNi_1/3Co_1/3Mn_1/3O₂/LiFePO₄ composite cathodes with the LiFePO₄ mass content ranging from 10 to 30 wt% were prepared by ball milling in order to combine the merits of layered LiNi_1/3Co_1/3Mn_1/3O₂ and olivine LiFePO₄. The structure and morphology of the samples were characterized by X-ray diffraction and scanning electron microscope. The composite cathodes exhibited improved electrochemical performance compared with pristine LiNi_1/3Co_1/3Mn_1/3O₂. Among all the composite cathodes, the one with 20 wt% of LiFePO₄ showed the best electrochemical performance in terms of discharge capacity, cycle stability, and rate capability. Electrochemical impedance spectroscopy showed that mixing of LiFePO₄ in LiNi_1/3Co_1/3Mn_1/3O₂ decreased the internal resistance of the electrode, retarded the formation of SEI film, and facilitated the charge transfer reaction. Differential scanning calorimetry showed that the composite cathode had better thermal stability than pristine LiNi_1/3Co_1/3Mn_1/3O₂.     

ZrO2 coating of LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ materials were prepared by hydroxide precipitation. The structure and electrochemical properties of the ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ were investigated using X-ray diffraction, scanning electron microscope, and charge–discharge tests, indicating that the lattice structure of LiNi_1/3Co_1/3Mn_1/3O₂ were unchanged after the coating but the cycling stability was improved. As the coating amount increased from 0.0 to 0.5 mol.%, the initial capacity of the coated LiNi_1/3Co_1/3Mn_1/3O₂ decreased slightly; however, the cycling stability increased remarkably over the cut-off voltages of 2.5~4.3 V and the capacity retention reached 99.5% after 30 cycles at the coating amount of 0.5 mol.%. ZrO₂ coating also improved the cycling stability of LiNi_1/3Co_1/3Mn_1/3O₂ over wider cut-off voltage of 2.5~4.6 V.     

Hydrothermal synthesis and electrochemical performance studies of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 for lithium-ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ nanocrystallites were synthesized by a one-step hydrothermal method, and uniform second particles were formed by a subsequent calcination process. X-ray diffraction results indicate that the as-synthesized material can be indexed by α-NaFeO₂ layered structure with R-3 m space group. The results of Rietveld refinements show the I ₀₀₃/I ₁₀₄ value of the material is 2.032, and the nanostructured material presents low cation mixing, small cell volume, and a consequent suppression of lattice strain. The rate performances of the as-synthesized material can be further improved by coating Al₂O₃. The discharging capacity of Al₂O₃-coated material reaches 154.4 mAh g^?1, and the capacity retention maintains 80.3 % after 50 cycles at 5 C in the voltage range of 2.5 to 4.5 V, while those of the bare one is only 139.0 mAh g^?1 and 71.6 %, respectively. The transmission electron microcopy observation shows no zigzag layer exists on the surface of particle after cycles for Al₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂. Compared to bare LiNi_1/3Co_1/3Mn_1/3O₂, the de-intercalation potential difference before and after cycles of Al₂O₃-coated one is smaller. This indicates that Al₂O₃ coating can reduce the electrochemistry polarization in the electrode bulk.     

Synthesis of spherical LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ was successfully prepared by controlled crystallization. The preparation started with the spherical coprecipitate of Ni_1/3Co_1/3Mn_1/3CO₃ from NiSO₄, CoSO₄, MnSO₄, NH₄HCO₃, and NH₃·H₂O, followed by pyrolysis of Ni_1/3Co_1/3Mn_1/3CO₃ at 600°C for 3 h. The X-ray diffraction analysis showed that the homogeneous cubic (Ni_1/3Co_1/3Mn_1/3)₃O₄ was obtained after the pyrolysis. Spherical LiNi_1/3Co_1/3Mn_1/3O₂ was obtained by sintering of the mixture of as-obtained (Ni_1/3Co_1/3Mn_1/3)₃O₄ and LiOH·H₂O at 900°C for 6 h in air. As-prepared spherical LiNi_1/3Co_1/3Mn_1/3O₂ presented initial discharge capacity of 162.9 mA h g⁻¹ and capacity retention of 98% at 50th cycle.     

TiO2 coating of LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

TiO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ materials were prepared by the hydrolyzation of Ti(OBu)₄. The impact of TiO₂ coating on the structure and electrochemical properties of LiNi_1/3Co_1/3Mn_1/3O₂ was investigated using X-ray diffraction, scanning electron microscope, and charge–discharge tests. The results indicated that TiO₂ coating did not affect the lattice of LiNi_1/3Co_1/3Mn_1/3O₂, but exhibited obvious effects on its discharge capacity and cycling stability. As coated TiO₂ increased from 0.0 to 2.0 mol%, the initial capacity of samples decreased slightly, but the cycling stability over 2.5∼4.3 V increased remarkably. The capacity retention reached 99.5% at the 50th cycle at a coating amount of 2.0 mol%.     

Improving the rate performance and stability of LiNi<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>O<Subscript>2</Subscript> in high voltage lithium-ion battery by using fluoroethylene carbonate as electrolyte additive

Fluoroethylene carbonate (FEC) is investigated as the electrolyte additive to improve the electrochemical performance of high voltage LiNi_0.6Co_0.2Mn_0.2O₂ cathode material. Compared to LiNi_0.6Co_0.2Mn_0.2O₂/Li cells in blank electrolyte, the capacity retention of the cells with 5 wt% FEC in electrolytes after 80 times charge-discharge cycle between 3.0 and 4.5 V significantly improve from 82.0 to 89.7%. Besides, the capacity of LiNi_0.6Co_0.2Mn_0.2O₂/Li only obtains 12.6 mAh g^?1 at 5 C in base electrolyte, while the 5 wt% FEC in electrolyte can reach a high capacity of 71.3 mAh g^?1 at the same rate. The oxidative stability of the electrolyte with 5 wt% FEC is evaluated by linear sweep voltammetry and potentiostatic data. The LSV results show that the oxidation potential of the electrolytes with FEC is higher than 4.5 V vs. Li/Li⁺, while the oxidation peaks begin to appear near 4.3 V in the electrolyte without FEC. In addition, the effect of FEC on surface of LiNi_0.6Co_0.2Mn_0.2O₂ is elucidated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The analysis result indicates that FEC facilitates the formation of a more stable surface film on the LiNi_0.6Co_0.2Mn_0.2O₂ cathode. The electrochemical impedance spectroscopy (EIS) result evidences that the stable surface film could improve cathode electrolyte interfacial resistance. These results demonstrate that the FEC can apply as an additive for 4.5 V high voltage electrolyte system in LiNi_0.6Co_0.2Mn_0.2O₂/Li cells.     

Characterization of Na-substituted LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium-ion battery

Highly crystalline layered Li_1?xNa_xNi_1/3Co_1/3Mn_1/3O₂ (x?=?0, 0.001, 0.01, 0.03, 0.05) materials are synthesized by molten salts method and characterized by scanning electron microscopy, inductively coupled plasma (ICP), X-ray diffraction, Rietveld refinement, and electrochemical measurement, respectively. ICP, SEM, and EDS results show that Na ions are incorporated in LiNi_1/3Co_1/3Mn_1/3O₂. Rietveld refinement results show that suitable Na substitution leads to stable layered structure by full Na occupying in Li layer and further attributes to low cation mixing. Electrochemical studies demonstrate that the Na-substituted LiNi_1/3Co_1/3Mn_1/3O₂ shows improved rate capability and cycling performance compared to that of pure LiNi_1/3Co_1/3Mn_1/3O₂.     

Enhanced electrochemical properties and thermal stability of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by surface modification with Eu<Subscript>2</Subscript>O<Subscript>3</Subscript>

Layered LiNi_1/3Co_1/3Mn_1/3O₂ cathode material is synthesized via a sol-gel method and subsequently surface-modified with Eu₂O₃ layer by a wet chemical process. The effect of Eu₂O₃ coating on the electrochemical performances and thermal stability of LiNi_1/3Co_1/3Mn_1/3O₂@Eu₂O₃ cells is investigated systematically by the charge/discharge testing, cyclic voltammograms, AC impedance spectroscopy, and DSC measurements, respectively. In comparison, the Eu₂O₃-coated sample demonstrates better electrochemical performances and thermal stability than that of the pristine one. After 100 cycles at 1C, the Eu₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode demonstrates stable cyclability with capacity retention of 92.9 %, which is higher than that (75.5 %) of the pristine one in voltage range 3.0–4.6 V. Analysis from the electrochemical measurements reveals that the remarkably improved performances of the surface-modified composites are mainly ascribed to the presence of Eu₂O₃-coating layer, which could efficiently suppress the undesirable side reaction and increasing impedance, and enhance the structural stability of active material.     

Enhanced electrochemical performances of LiNi0.5Co0.2Mn0.3O2 cathode material co-coated by graphene/TiO2

The electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523) layered cathode material, such as poor rate capacity and cycling stability caused by undesirable intrinsic conductivity and low rate of lithium ion transportation, are not fairly good especially at elevated rate and cut-off voltage. To improve these properties, in this study, the co-coating layer of graphene and TiO₂ was constructed on NCM523 surface. The graphene/TiO₂ coating layer could effectively prevent hydrofluoric acid (HF) attacks, suppress the side reaction, accelerate the lithium ion diffusion and facilitate the electron migration. The enhancement of cycle performance and rate capacity was contributed to the uniform co-modified surface, interacting each other and thus exhibiting synergistic effects.     

The intercalation/deintercalation kinetic studies on the structure-integrated cathode material 0.5Li2MnO3 0.5LiNi0.5Mn0.5O2

A cathode material, 0.5Li₂MnO₃ 0.5LiNi_0.5Mn_0.5O₂, was prepared by citric acid-assisted sol–gel method and its electrochemical performance was investigated. It delivered a charge capacity of 270 mAh g^?1 and a discharge capacity of 189 mAh g^?1 in the first cycle. With the increase of current density from 14 to 28 mA g^?1, the discharge capacity dropped severely to 130 mA g^?1. Obviously, the rate capability of the material was inferior to most of the oxide cathode materials. The diffusion coefficient of this material was calculated to be 6.04?×?10^?12 cm² s^?1 from the results of cyclic voltammetry measurements. Moreover, diffusion coefficients between 3.13?×?10^?12 and 1.22?×?10^?10 cm² s^?1 in the voltage range of 3.8–4.7 V were obtained by capacity intermittent titration technique. This, together with the localized Li₂MnO₃ domains in the crystal structure, may validate the poor rate capability.     

Improvement of cycling and thermal stability of LiNi<Subscript>0.8</Subscript>Mn<Subscript>0.1</Subscript>Co<Subscript>0.1</Subscript>O<Subscript>2</Subscript> cathode material by secondly treating process

(Ni_0.8Mn_0.1Co_0.1)(OH)₂ and Co(OH)₂ secondly treated by LiNi_0.8Mn_0.1Co_0.1O₂ have been prepared via co-precipitation and high-temperature solid-state reaction. The residual lithium contents, XRD Rietveld refinement, XPS, TG-DSC, and electrochemical measurements are carried out. After secondly treating process, residual lithium contents decrease drastically, and occupancy of Ni in 3a site is much lower and Li/Ni disorder decreases. The discharge capacity is 193.1, 189.7, and 182 mAh g^?1 at 0.1 C rate, respectively, for LiNi_0.8Mn_0.1Co_0.1O₂-AP, -NT, and -CT electrodes between 3.0 and 4.2 V in pouch cell. The capacity retention has been greatly improved during gradual capacity fading of cycling at 1 C rate. The noticeably improved thermal stability of the samples after being treated can also be observed.     

Structural, transport and electrochemical properties of LiNi1 − yCoyMn0.1O2 and Al, Mg and Cu-substituted LiNi0.65Co0.25Mn0.1O2 oxides

LiNi_{1 - y − z}Co_yMn_zO₂ (y = 0.25, 0.35, 0.5, 0.6; z = 0.1, 0.2), LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂, LiNi_0.65Co_0.25Mn_0.08Al_0.02O₂, LiNi_0.65Co_0.25Mn_0.08Mg_0.02O₂ and LiNi_0.65Co_0.25Mn_0.08Al_0.01Mg_0.01O₂ cathode materials were synthesized by a soft chemistry EDTA-based method. Structural and transport properties of pristine and delithiated materials (Li_xNi_0.65Co_0.25Mn_0.1O₂, Li_xNi_0.55Co_0.35Mn_0.1O₂ and LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ oxides) are presented. In the considered group of oxides there is no correlation between electrical conductivity and the a parameter (M-M distance in the octahedra layers). The results of electrochemical performance of cathode materials are presented. The best stability during first 10 cycles was obtained for Li/Li_xNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ cell due to enhanced kinetics of intercalation process.     

The properties research of ferrum additive on Li [Ni<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>] O<Subscript>2</Subscript> cathode material for lithium ion batteries

Li[Ni_1/3Co_(1-x)/3Mn_1/3Fe _x/3] O₂(x?=?0.0, 0.1, 0.3, 0.5, 0.7, and 0.9) cathode materials have been synthesized via hydroxide co-precipitation method followed by a solid state reaction. Thermogravimetry (TG) and differential thermal analysis (DTA) measurements were utilized to determine the calcination temperature of precursor sample. The crystal structure features were characterized by X-ray diffraction (XRD). The electrochemical properties of Li[Ni_1/3Co_(1-x)/3Mn_1/3Fe _x/3]O₂ were compared by means of cyclic voltammetry (CV), electrochemical impedance spectroscopy(EIS), and galvanostatic charge/discharge test. Electrochemical test results indicate that Li[Ni_1/3Co_0.9/3Mn_1/3Fe_0.1/3] O₂ decrease charge transfer resistance and enhance Li⁺ ion diffusion velocity and thus improve cycling and high-rate capability compared with Li[Ni_1/3Co_1/3Mn_1/3]O₂. The initial discharge specific capacity of Li[Ni_1/3Co_0.9/3Mn_1/3Fe_0.1/3] O₂ was 178.5 mAh/g and capacity retention was 87.11 % after 30 cycles at 0.1C, with the battery showing good cycle performance.     

Effects of lithium excess amount on the microstructure and electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material

Spinel LiNi_0.5Mn_1.5O₄ cathode materials with different lithium excess amount (0, 2%, 6%, 10%) were synthesized by a facile solid-state method. The effect of lithium excess amount on the microstructure, morphology, and electrochemical properties of LiNi_0.5Mn_1.5O₄ materials was systematically investigated. The results show that the lithium excess amount does not change the particle morphology and size obviously; thus, the electrochemical properties of LiNi_0.5Mn_1.5O₄ are mainly determined by structural characteristics. With the increase of lithium excess amount, the cation disordering degree (Mn³⁺ content) and phase purity first increase and then decrease, while the cation mixing extent has the opposite trend. Among them, the LiNi_0.5Mn_1.5O₄ material with 6% lithium excess amount exhibits higher disordering degree and lower impurity content and cation mixing extent, thus leading to the optimum electrochemical properties, with discharge capacities of 125.0, 126.1, 124.2, and 118.9 mAh/g at 0.2-, 1-, 5-, and 10-C rates and capacity retention rate of 96.49% after 100 cycles at 1-C rate.     

Electrochemical characterization of a lithiated mixed nickel-cobalt oxide (LiNi0.5Co0.5O2) prepared by sol-gel process

Lithiated transition metal oxides having a layered structure and general formula LiMO₂, have been extensively studied as positive electrode active materials for lithium or lithium-ion batteries. In particular, lithium nickel dioxide (LiNiO₂) and lithium cobalt dioxide (LiCoO₂) present a layered structure with high diffusion coefficients for the lithium ion. This latter property is very important in order to realize practical devices having high discharge rates. LiNiO₂, compared with LiCoO₂, has the advantage to be a cheaper material with a higher specific capacity for lithium cycling, but its stability upon cycling can be greatly influenced by the displacement of Ni ions from the Ni layers to the Li planes as the content in lithium is reduced over a certain value. Recently, solid solutions such as LiNi_xCo_1−xO₂ have been proposed to offer a compromise between stability, cost and capacity. In this work we have studied LiNi_0.5Co_0.5O₂ prepared by the Complex Sol-Gel Process (CSGP). The advantage of this procedure toward the solid-state process is the high homogeneity in composition and in particle dimension of the synthesized compounds. The samples have been characterized electrochemically using chronopotentiometric, voltammetric and impedance measurements in liquid electrolyte. The results indicates that CSGP-synthesized LiNi_0.5Co_0.5O₂ shows good cyclability (after 1000 cycles about 2/3 of the initial capacity can still be cycled) only if the anodic potential is limited to about 4.2 V. The quite low values of the specific capacity (∼70 mAh/g at C/1 charge-discharge rate) can be justified by the non-complete calcination reaction, as suggested by X-ray measurements. Kinetic properties have been evaluated by Electrochemical Impedance Spectroscopy measurements, which have shown quite high values for the lithium chemical diffusion coefficient (10⁻⁷÷10⁻⁸ cm²s⁻¹) and its unexpected decrease as deintercalation proceeds from x=0.5 in LiNi_0.5Co_0.5O₂. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

Effects of Ca doping on the electrochemical properties of LiNi0.8Co0.2O2 cathode material

LiNi_0.8Co_0.2O₂ and Ca-doped LiNi_0.8Co_0.2O₂ cathode materials were synthesized via a rheological phase reaction method. It is found that the Ca doping significantly improves reversible capacity, cycling performance, thermal stability and rate capability. The Ca-doped LiNi_0.8Co_0.2O₂ cathode material maintains nearly its initial discharge capacity up to 100 cycles at room temperature. It also delivers an initial discharge capacity of 183 mA h g^− 1 and still keeps 131 mA h g^− 1 even after 120 cycles at 60 °C. These results, together with the X-ray diffraction and electrochemical impedance spectroscopy analysis, reveal that Ca²⁺ ions occupy Li⁺ ion sites to form Ca_Li defects and lithium vacancies (V_Li′), which reduce the resistance and increases conductivity of LiNi_0.8Co_0.2O₂.     

Electrochemical studies on mixtures of LiNi0.8Co0.17Al0.03O2 and LiCoO2 cathode materials for lithium ion batteries

Detailed electrochemical investigations have been carried out on LiNi_0.8Co_0.17Al_0.03O₂ as cathode materials for lithium ion batteries in the potential range of 2.8-4.3 V. This sample showed an initial discharge capacity of 186 mAh/g which corresponds to 67% of its theoretical capacity. The effect of addition of LiCoO₂ to LiNi_0.8Co_0.17Al_0.03O₂ in the ratio 10:90, 30:70, 50:50 has been studied. The results showed that the addition of LiCoO₂ has improved the working voltage of the cell. In addition, the percentage retention (95%) of the cell is significantly increased in the composition ratio 50:50.     

Effects of Sn doping on electrochemical characterizations of Li[Ni<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>]O<Subscript>2</Subscript> cathode material

Li[Ni_1/3Co_1/3Mn_1/3]O₂ and Sn-doped Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode materials for lithium battery are synthesized by a solid-state method. The samples are characterized by X-ray diffraction, scanning electron microscope, electrochemical impedance spectroscopy (EIS), and charge–discharge test. The results show that the Sn-doped Li[Ni_1/3Co_1/3Mn_1/3]O₂ has a typical hexagonal α-NaFeO₂ structure and strawberry-like shape with uniform particle size. It has also been found that the Sn-doped Li[Ni_1/3Co_1/3Mn_1/3]O₂ reveals better electrochemical performances than that without Sn doping. The EIS results suggest that Sn presence decreases the total resistance of Li[Ni_1/3Co_1/3Mn_1/3]O₂, which should be related to the improvement on the electrochemical properties.