Determination of vanadium by solid-phase spectrophotometry after its preconcentration as an Eriochrome Cyanine R complex on a dextran-type exchanger

A method is described for the determination by solid phase spectrophotometry (SPS) of trace amounts of vanadium in natural water and crude petroleum samples. The procedure is based on fixation on a dextran-type anion exchanger of the complex V(IV)-Eriochrome Cyanine R. The absorbance of the gel, at 563 and 750 nm, packed in a 1 mm cell, is measured directly. Vanadium can be determined in the 0.6-25.0 mug l(-1) range with a relative standard deviation of 2.2%. The comparison of the SPS method and the gallic acid persulphate method shows that the linearity, analytical sensitivity and precision were better for the SPS method, and that the latter method has lower detection and quantification limits than the gallic acid persulphate method.     

Elimination of the interferences of anions in the kinetic spectrophotometric determination of vanadium (V) solution

Accurate determination of vanadium (V) in industrial waste water is of great importance in environmental, biological and toxicological studies. Most of kinetic spectrophotometric methods based on the catalytic effect of vanadium (V), when applied to real samples for determination of trace levels of vanadium (V) lack the satisfactory sensitivity and selectivity. This may be attributed to the serious interferences of various anions which are common pollutants in industrial waste water. The oxidation of gallic acid by ammonium persulphate, catalysed by vanadium (V) was chosen for our study. The effect of the serious interferences of various anions such as chloride, bromate, bromide, chromate, iodide, iodate, molybdate, carbonate and sulphate on the net absorbance given by 4 microg l(-1) of vanadium (V) solution were studied. The minimum concentrations of citric acid, EDTA, ascorbic acid and oxalic acid as leveling off agents required to level off interfering effects due to the aforementioned anions in the kinetic determination of vanadium (V) were 50, 70, 80 and 120 microg ml(-1), respectively. In the presence of optimum concentrations of effective leveling off agents, the dynamic range can be extended and sensitivity increased as compared with the proposed method without levelling off agents. The proposed method is a rapid, sensitive and selective method for the determination of ultra trace amounts of vanadium (V) in real samples with satisfactory results.     

Flow-injection spectrophotometric determination of trace vanadium based on catalysis of the gallic acid bromate reaction

High sensitivity is obtained by using high concentrations of gallic acid and bromate, although the uncatalyzed reaction is significant. Various reactant concentrations, reaction temperature, pH and residence times can be used to alter the linear calibration ranges and sensitivity for vanadium. With reagent streams of 1.76 M bromate and 0.06 M gallic acid at pH 3.8 (each at 1 ml min^?1), 0.2–20 ng of vanadium (20-μl injections) can be determined at 30°C. Oxidized gallic acid is detected at 380 nm. When the bromate concentration is decreased to 0.5 M and the temperature is 65°C, 0.05–4 ng of vanadium can be determined; the relative standard deviation is ca. 5% for 0.6 ng of vanadium. The toleranes for Al(III), Fe(III), Mo(VI) and iodide are 10 ng, 10 ng, 50 ng and 200 ng, respectively, for the determination of 1 ng of vanadium. About 12 samples can be injected per hour.     

Determination of vanadium in refractory metals, steel, cast iron, alloys and silicates by extraction of an NBPHA complex from a sulphuric-hydrofluoric acid medium

A method for determining up to 0.15% of vanadium in high-purity niobium and tantalum metals, cast iron, steel, non-ferrous alloys and silicates is described. The proposed method is based on the extraction of a red vanadium(V)-N-benzoyl-N-phenylhydroxylamine complex into chloroform from a sulphuric-hydrofluoric acid medium containing excess of ammonium persulphate as oxidant. The molar absorptivity of the complex is 428 l.mole(-1).mm(-5) at 475 nm, the wavelength of maximum absorption. Interference from chromium(VI) and cerium(IV) is eliminated by reduction with iron(II). Common ions, including large amounts of titanium, zirconium, molybdenum and tungsten, do not interfere.     

A modified catalytic-photometric method for the determination of vanadium in chloride rich hydro-geochemical samples

The vanadium content in chloride rich hydrogeochemical samples has been determined through a modification in the existing standard gallic acid oxidation method which has severe interference problem from halides. The modification incorporates a preliminary fume-drying of the sample aliquot with a mixture of perchloric and sulphuric acids. This ensures total removal of halides and hence their interference. The estimation is completed as per the standard method after taking the sample in 10 ml of 1% nitric acid. Also mercuric nitrate addition which forms a part of the standard procedure to prevent halide interference, is also dispensed with keeping in view the toxic nature of mercury. The method has been tried on a number of samples having varying chloride content. The results obtained compare well with the standard PAR method. The method can be used to determine vanadium down to 1 ppb. The relative standard deviation obtained for vanadium contents in the range 400–10 ppb is in the range 4–8.2%.     

A silver nanoparticle-based method for determination of antioxidant capacity of rapeseed and its products

A novel silver nanoparticle-based (AgNP) method and two modified procedures, ferric reducing antioxidant power (FRAP) and 2,2'-diphenyl-1-picrylhydrazyl (DPPH), were used for determination of antioxidant capacities of the ethanolic, methanolic, methanolic-aqueous (1?:?1 v/v) and aqueous extracts of rapeseed and its products. The AgNP method based on the electron-transfer reaction between silver ions and antioxidants in an optimized ammonium buffer medium (pH = 8.4) and determination of silver nanoparticle formation has been elaborated. The novel AgNP method was validated using sinapic acid, gallic acid, caffeic acid, ascorbic acid and quercetin as standard antioxidant solutions in concentration ranges of 0.03-0.21 μmol mL(-1), 0.02-0.20 μmol mL(-1), 0.01-0.18 μmol mL(-1), 0.03-0.30 μmol mL(-1) and 0.001-0.009 μmol mL(-1). The calculated detection (DL = 0.01, 0.02, 0.009, 0.02 and 0.0004 μmol mL(-1) for sinapic, gallic, caffeic, ascorbic acids and quercetin, respectively) and quantification limits (QL = 0.04, 0.06, 0.03, 0.08 and 0.001 μmol mL(-1) for sinapic, gallic, caffeic, ascorbic acids and quercetin, respectively) confirm linearity concentration ranges for determination of antioxidant capacity by AgNP assay. The average antioxidant capacities of the studied rapeseed samples ranged between 14.7 and 126.2 μmol sinapic acid per gram for the proposed AgNP method, 7.4-112.7 μmol sinapic acid per gram for the FRAP method and 39.1-339.8 μmol sinapic acid per gram for DPPH assay. The methanol-water mixture (1:1 v/v) was the most efficient solvent for extraction of antioxidants from the studied rapeseed samples. There are significant, positive correlations between the novel AgNP and the modified FRAP, DPPH and FC methods for all extracts of the studied rapeseed samples (r = 0.7564-0.8516, p < 0.001). Satisfactory values of precision (RSD = 1.2-4.4%) and accuracy (recovery = 95.6-104.6%, except methanolic extracts) demonstrate the benefit of the proposed AgNP method for analysis of the antioxidant capacity of rapeseed samples. Results of the principal component analysis (PCA) indicate that there are differences between the total amounts of antioxidants in rapeseed samples extracted by different solvents.     

Kinetic-spectrophotometric determination of trace amounts of vanadium(V) based on its catalytic effect on the reaction of DBM-arsenazo and potassium bromate

A simple and sensitive kinetic-spectrophotometric method is developed for the determination of trace vanadium(V), based on the catalytic effect of vanadium(V) on the oxidation of DBM-arsenazo by potassium bromate in 0.0138 moll(-1) phosphoric acid medium and at 100 degrees C in the presence of citric acid as activator. The absorbance is measured at 528 nm with the fixed-time method. The optimization of the operating conditions regarding concentrations of the reagents, temperature and interferences are also investigated. The working curve is linear over the concentration range 0-20 ngml(-1) of vanadium(V) with good precision and accuracy and the detection limit was down to 3.44 ngl(-1). The relative standard deviation for a standard solution of 14 ngml(-1) is 0.28% (n=11). The apparent activity energies of the catalytic reaction and the non-catalytic reaction are 73.48, 113.5 kJ/mol, respectively. The proposed method proved highly sensitive, selective and relatively rapid for the assay of vanadium at low-level range of 0-20 ngml(-1) without any pre-concentration step. Thw method was applied to the determination of vanadium(V) in steels, rice, flour, cabbage, potato, fish, shrimp and tea samples with satisfactory results. The obtained results for the steel samples were excellent agreement with the standard reference values. The analytical results of the rice, flour, cabbage, potato, fish, shrimp and tea samples were excellent agreement with those of atomic absorption spectrometry. The recovery experiments have been made for the rice, flour, cabbage, potato, fish, shrimp and tea samples except the steels; excellent results were obtained. The relative standard deviations were over the range of 0.18-2.60% and the recoveries were over the range of 98.00-102.4%, respectively. The analytical results obtained were satisfactory.     

An adsorption-catalytic test method for determining vanadium

The promoting effect of vanadium(V, IV) in the reaction of gallic acid oxidation with bromate ions in aqueous solutions was studied, and the dependence of the rates of catalytic and noncatalytic reactions on the concentration of components was found. A catalytic mechanism was proposed based on the experimental results and data of quantum-mechanical calculations. The linear dependence of the rate of the catalytic reaction on the concentration of vanadium(V)/vanadium(IV) was used to determine these ions in solutions by catalytic photometry. The detection limit was 0.01 μg in an aliquot portion of the test solution; the determination error was less than 20%. The conditions were found for stabilizing the properties of paper supports for more than 30 days, since the interaction of filter and chromatographic papers with bromate ions was found. An adsorption- catalytic test method was proposed for the semiquantitative visual determination of vanadium ions in water and aqueous solutions by the color of the pretreated paper strip immersed in the test solution. The detection limit for vanadium ions was 0.1 mg/L. The 100-fold amounts of Ni(II), Mn(II), Cr(III), and Co(II) do not interfere with the determination. The method was tested on river and sea water samples from different sources.     

Polarography of metal-gallic complexes

The polarographic behavior of metal ions in perchlorate media containing gallic acid is described. Tungsten(VI) forms a complex with gallic acid which yields a single wave in these media, useful in the polarographic determination of tungsten. Evidence for complexation of chromium(III), copper(II), iron(III), molybdenum(VI), uranium(VI), vanadium(V), tungsten(VI), praseodymium(III), samarium(III), neodymium(III) and gadolinium(III) is obtained and the behavior of these metal ions is summarized.     

Evaluation of oxidant media for the determination of lead in food slurries by hydride generation atomic absorption spectrometry

Several oxidant media were evaluated for the generation of lead hydride from slurry samples and their application to the determination of lead in vegetables and fish by hydride generation atomic absorption spectrometry. Three oxidant - acid media were compared: hydrogen peroxide - nitric acid, ammonium persulphate - nitric acid and potassium dichromate - lactic acid. The powdered samples were suspended in Triton X-100 and shaken with 10.0 g of blown zirconia spheres until a slurry was formed. The potassium dichromate - lactic acid medium was the most satisfactory for the determination of lead in fish and vegetables, providing the lowest detection limits as a result of its high sensitivity and low blank values. The ammonium persulphate - nitric acid medium gave good accuracy, precision and selectivity for vegetables (1-2 p.p.m. of lead); however, with fish (0.1-1 p.p.m. of lead) it was only a semi-quantitative medium for the determination of lead owing to its lack of sensitivity and selectivity. The hydrogen peroxide - nitric acid medium was unsatisfactory for the generation of lead hydride from slurry samples because of decomposition of hydrogen peroxide by the organic matter in the sample.     

Flow injection electrogenerated chemiluminescence determination of vanadium and its application to environmental water sample

A selective flow injection electrogenerated chemiluminescence(CL) method for the determination of vanadium is described in this paper. It was based on the chemiluminescence reaction of luminol with vanadium(II), which was on-line electrogenerated from vanadate using a flow-through carbon electrolytic cell. Under the optimal conditions, the CL intensity was linear to the concentration of vanadium in the range of 5.0x10(-10)-1.0x10(-7) gml(-1) with a detection limit of 2x10(-10) gml(-1) vanadium. The relative standard deviation was 4% for 5.0x10(-8) gml(-1) vanadium in 11 repeated measurements. The method has been successfully applied to the determination of vanadium in environmental water samples.     

催化动力学极谱法测定痕量钒

在硫酸介质中,以酒石酸为活化剂,痕量钒对溴酸钾氧化甲基橙的反应有极强的催化作用,以极谱法监测催化反应过程中甲基橙及其氧化产物浓度的变化,建立了双峰指示催化动力学极谱法制定痕量钒的新方法,方法的线性范围为0.23-3.70μg/L,检出限为0.17μg/L。方法已用于食品及水样中痕量钒的测定。     

Continuous flow system for the determination of trace vanadium in natural waters utilizing in-line preconcentration/separation coupled with catalytic photometric detection

A sensitive and rapid method is presented for the determination of vanadium at ng to sub-ng ml(-1) levels in natural waters, in which in-line preconcentration/separation is directly coupled with catalytic detection of vanadium in a flow-injection system. Vanadium was adsorbed on a small column packed with Sephadex G-25 gel and desorbed with a small volume of 0.010 M HCl. The catalytic action of vanadium on the oxidation of chromotropic acid (1,8-dihydroxy-3,6-naphthalenedisulphonic acid) by bromate in pH 3.8 buffered media was used in the sensitive determination of vanadium. Effective preconcentration/separation of trace vanadium can be achieved from Fe(III), Cu(II) and a large excess of sodium chloride in seawater sample. A linear calibration using a 5 m sample loop was obtained for vanadium in the range 0-2.5 ng ml(-1). The limit of detection was 0.02 ng ml(-1) and the relative standard deviation was 1.2% for 1.0 ng ml(-1) vanadium (n=5). The present FIA system is rapid and sensitive and can be readily applied to river water and coastal seawater samples.     

High-performance thin-layer chromatography densitometric method for the simultaneous determination of three phenolic acids in Syzygium aromaticum (L.) Merr. & Perry

A simple, precise, and rapid high-performance thin-layer chromatographic (HPTLC) method has been developed for the simultaneous determination of 3 phenolic acids, i.e., gallic acid, caffeic acid, and syringic acid, in the dried buds of Syzygium aromaticum, commonly known as clove. HPTLC was performed on silica gel 60F254 plates with toluene-ethyl acetate-formic acid (8 + 2 + 1) mobile phase and densitometric scanning at 280 nm. The method was validated for selectivity, linearity, precision, and repeatability. Instrumental precision coefficient of variation (CV) was 0.88, 0.93, and 0.98% and repeatability of the method (CV) was 0.76, 0.64, and 0.69% for gallic acid, caffeic acid, and syringic acid, respectively. The linear concentration ranges were 400-3200 ng/spot with a correlation coefficient of 0.993 for gallic acid, 440-3520 ng/spot with a correlation coefficient of 0.994 for caffeic acid, and 400-4000 ng/spot with a correlation coefficient of 0.993 for syringic acid. The average recoveries of gallic acid, caffeic acid, and syringic acid were 96.3, 95.7, and 92.4%, respectively. Gallic acid, caffeic acid, and syringic acid were present at levels of 1.58, 0.06, and 0.05% (w/w), respectively, in S. aromaticum. This method is simple, accurate, precise, and economical and can be used for routine quality control.     

Determination of trace vanadium in natural waters by a combined ion exchange—catalytic photometric method

A sensitive, selective and simple method is described for the determination of trace vanadium in natural waters. Vanadium is separated and concentrated by a combined cation- and anion-exchange procedure in 0.05 M HCl—0.1 % H₂O₂ media, and determined by the catalytic method based on the oxidation of gallic acid by bromate. The proposed method is applied to the analysis of natural waters. The relative standard deviations are 3.9 % for 0.8 p.p.b. of vanadium in river water and 3.2 % for 1.9 p.p.b. of vanadium in lake water (surface). As little as 0.03 p.p.b. of vanadium can be determined in samples of 100 ml or less.     

Use of N-benzyl-2-naphthohydroxamic acid as a highly selective reagent for solvent extraction and spectrophotometric determination of vanadium(V)

N-Benzyl-2-naphthohydroxamic acid extracts vanadium(V) selectively and quantitatively into chloroform from 2-8.5M hydrochloric acid in the presence of Mo(VI), Zr(IV) and Ce(IV). The extraction takes place quickly and gives a stable reddish-violet extract which shows an absorption maximum at 505 nm with molar absorptivity of (5.34 +/- 0.05) x 10(3) 1.mole(-1).cm(-1). The optimum range for the determination is 2.2-7.4 ppm of vanadium(V) in the final solution. The method has been used for the determination of vanadium in steels.     

Speciation and preconcentration of vanadium(V) and vanadium(IV) in water samples by flow injection-inductively coupled plasma optical emission spectrometry and ultrasonic nebulization

An on-line separation, preconcentration and determination system for vanadium(IV) and vanadium(V) comprising inductively coupled plasma optical emission spectrometry (ICP-OES) coupled to a flow injection (FI) method with an ultrasonic nebulization (USN) system was studied. The vanadium species were retained on an Amberlite XAD-7 resin as a vanadium-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (V-5-Br-PADAP) complex at pH 3.7. Enhanced selectivity was obtained with the combined use of the formation on-line of the complexes and 1,2-cyclohexanediaminetetraacetic acid (CDTA) as masking agent. The vanadium complexes were removed from the microcolumn with 25% v/v nitric acid. A sensitivity enhancement factor of 225 was obtained with respect to ICP-OES using pneumatic nebulization (15-fold for USN and 15-fold for the microcolumn). The detection limit for the preconcentration of 10 mL of aqueous solution was 19 ng L-1. The precision for 10 replicate determinations at the 5 micrograms L-1 V level was 2.3% relative standard deviation (RSD), calculated from the peak heights obtained. The calibration graph using the separation and preconcentration system for vanadium species was linear with a correlation coefficient of 0.9992 at levels from near the detection limits up to at least 100 micrograms L-1. The method was successfully applied to the speciation of vanadium in river water samples.     

Sorption behavior of vanadium on silica gel modified with tetrakis(4-carboxyphenyl)porphyrin.

Tetrakis(4-carboxyphenyl)porphyrin (TCPP) has been loaded on aminopropyl-silica gel by physical adsorption and by direct immobilization through formation of an amide bond to obtain chelating sorbents. These sorbents have been studied for preconcentration and separation of vanadium prior to its determination by atomic absorption spectrometry. Several parameters, such as sorption capacity of the chelating resin, pH for retention of V(IV) and V(V), volume of sample and eluent, were evaluated. Both vanadium species sorbed on TCPP-modified resin could be eluted using 2 mol L(-1) nitric acid solution. The recovery values were > 94% and preconcentration factor of 160 was obtained. For speciation analysis, cyclohexane-1,2-diaminetetraacetic acid (CDTA) was added to the sample for complexation of vanadium(IV), which was not retained on the microcolumn. The proposed method was examined for reference standard materials (TM-25.2 and CAAS-3) as well as for river water samples.     

Differential pulse polarographic determination of trace amounts of vanadium and molybdenum in various standard alloys and environmental samples after preconcentration of their morpholine-4-carbodithioates on microcrystalline naphthalene or morpholine-4-dithiocarbamate cetyltrimethyl-ammonium bromide-naphthalene adsorbent

A highly selective, sensitive, and fairly rapid and economical differential pulse polarographic (DPP) method has been reported for the determination of trace amounts of vanadium and molybdenum in standard alloys and various environmental samples. The morpholine-4-carbodithioates of these metals were retained (>99% recovery) quantitatively on microcrystalline naphthalene in the pH range 4.5-6.9 for vanadium and 1.5-4.5 for molybdenum. These metals were determined by DPP after desorption with 10 ml of 1 M HCl. Vanadium and molybdenum may also be preconcentrated by passing their aqueous solutions under similar conditions on morpholine-4-dithiocarbamate CTMAB-naphthalene adsorbent packed in a column at a flow rate of 1-5 ml min(-1) and determined similarly. The detection limits are 0.20 ppm for vanadium and 0.04 ppm for molybdenum at minimum instrumental settings (signal to noise ratio=2). The linearity is maintained in the following concentration ranges, vanadium 0.50-10.0 and molybdenum 0.10-9.0 ppm, with a correlation factor of 0.9996 (confidence interval of 95%, slopes 0.0196 and 0.01497 muA mug(-1), intercepts 3.65x10(-3) and -1.92x10(-3) respectively) and relative standard deviation of 1.1% in the microcrystalline method, while in the column method, the linearity is maintained in the concentration ranges, 0.50-6.5 for vanadium and 0.10-5.5 ppm for molybdenum with correlation factor of 0.9994 (with confidence interval of 95%, slopes 0.0194, 0.015 muA mug(-1), intercepts 3.60x10(-3) and -1.90x10(-3) respectively) and relative standard deviation of 1.4%. Various parameters such as the effect of pH, reagent, naphthalene and CTMAB concentrations, volume of aqueous phase and interference of a large number of metal ions on the estimation of vanadium and molybdenum have been studied in detail to optimize the conditions for their voltammetric determination at trace level in various standard alloys and environmental samples.     

Flow injection chemiluminescence determination of the total phenolics levels in plant-derived beverages using soluble manganese(IV)

This study established a flow injection (FI) methodology for the determination of the total phenolic content in plant-derived beverages based on soluble manganese(IV) chemiluminescence (CL) detection. It was found that mixing polyphenols with acidic soluble manganese(IV) in the presence of formaldehyde evoked chemiluminescence. Based on this finding, a new FI-CL method was developed for the estimation of the total content of phenolic compounds (expressed as milligrams of gallic acid equivalent per litre of drink) in a variety of wine, tea and fruit juice samples. The proposed method is sensitive with a detection limit of 0.02 ng mL⁻¹ (gallic acid), offers a wide linear dynamic range (0.5-400 ng mL⁻¹) and high sample throughput (247 samples h⁻¹). The relative standard deviation for 15 measurements was 3.8% for 2 ng mL⁻¹ and 0.45% for 10 ng mL⁻¹ of gallic acid. Analysis of 36 different samples showed that the results obtained by the proposed FI-CL method correlate highly with those obtained by spectrophotometric methods commonly used for the evaluation of the total phenolic/antioxidant level. However, the FI-CL method was found to be far simpler, more rapid and selective, with almost no interference from non-phenolic components of the samples examined.