Paramagnetic centers of photocatalysts based on nitrogen-doped titanium dioxide

Titanium dioxide doped with nitrogen (N-TiO₂) was studied by electron paramagnetic resonance spectroscopy. Two types of paramagnetic centers were observed: N^· and NO. The concentration of these centers depends significantly on temperature and irradiation with visible and UV light. It was established that the energy levels corresponding to the N^· and NO centers are, respectively, 2.3 and 2.0 eV below the N-TiO₂ conduction band. These centers are involved in the photooxidation of organic compounds on the N-TiO₂ surface.     

Electric field dependence of recombination kinetics in reaction centers of photosynthetic bacteria

Time-resolved charge recombination has been measured by reflectance/absorption spectroscopic analysis of Langmuir-Blodgett films of reaction centers of the photosynthetic bacterium, Rhodopseudomonas sphaeroides over a wide range of applied electric field strengths. The field dependence of the recombination kinetics has been deduced from the time-course of the reduction of the flash-oxidized bacteriochlorophyll dimer [(BChl)⁺₂] recorded at different applied field strengths. Measurements were performed under two different electric field biasing conditions: a constant bias and a high-frequency bipolar square-wave bias. The additional data obtained from bipolar biasing enabled the use of a new deconvolution method to obtain the field dependence of the rate constants from the experimental curves. The deconvolution shows that the rates for charge recombination from the flash-generated state back to the ground state (BChl)₂Q_A approximate exponential functions of the applied electric field. Correlation of the recombination kinetics data with photoinduced electrical response measurements on films with asymmetric up and down populations of reaction centers reveals that fields opposing charge separation result in faster rates of recombination. Although other possibilities are considered, the main source of the effect is believed to be a result of field-induced changes in the free energy gap between and (BChl)₂Q_A. The results presented here are compared to those obtained in experiments with solubilized reaction centers in which the free energy gap between and (BChl)₂Q_A has been changed by quinone replacement.     

Artificial photosynthetic reaction centers with carotenoid antennas

Two reaction center-antenna models based on a purpurin macrocycle linked to a C₆₀ and to a carotenoid polyene have been synthesized. In these systems the C₆₀ moiety is the primary electron acceptor, the purpurin is the primary electron donor and the carotenoid moiety acts both as an antenna and secondary electron donor. Formation of the initial charge separated state, C-Pur⁺-C₆₀⁻, following excitation with light absorbed by either the purpurin or C₆₀ takes place on the 10 ps time scale. The final charge separated state, C⁺-Pur-C₆₀⁻, is formed in one of the compounds with a quantum yield of 32% based upon light absorbed by the carotenoid. In order to function as an antenna, the carotenoid pigment must be electronically coupled to the purpurin. The purpurin C ring provides an excellent framework for locating a carotenoid polyene in partial conjugation with the macrocycle, leading to a relatively strong electronic communication between the chromophores; functionalization of a meso position of the purpurin provides a site for the covalent attachment of C₆₀.     

二氧化钛介孔分子筛的合成和表征

以高嵌段共聚物为模板剂在中性条件下制备二氧化钛介孔分子筛,并以TG-DTA,XRD,TEM和N~2吸附方法对脱除模板剂后的样品进行了表征。实验结果表明,该介孔分子筛具有较高的比表面,以及六方堆积的均匀孔道,焙烧过程中孔壁可部分晶化成锐钛矿型TiO~2的小晶粒。在分子筛孔壁中引入稀土元素可提高介孔结构稳定性。     

Artificial photosynthetic antennas and reaction centers

Presently, the world is experiencing an unprecedented crisis associated with the CO₂ produced by the use of fossil fuels to power our economies. As evidenced by the increasing levels in the atmosphere, the reduction of CO₂ to biomass by photosynthesis cannot keep pace with production with the result that nature has lost control of the global carbon cycle. In order to restore control of the global carbon cycle to solar-driven processes, highly efficient artificial photosynthesis can augment photosynthesis in specific ways and places. The increased efficiency of artificial photosynthesis can provide both renewable carbon-based fuels and lower net atmospheric levels of CO₂, which will preserve land and support the ecosystem services upon which all life on Earth depends. The development of artificial photosynthetic antennas and reaction centers contributes to the understanding of natural photosynthesis and to the knowledge base necessary for the development of future scalable technologies. This review focuses on the design and study of molecular and hybrid molecular-semiconductor nanoparticle based systems, all of which are inspired by functions found in photosynthesis and some of which are inspired by components of photosynthesis. In addition to constructs illustrating energy transfer, photoinduced electron transfer, charge shift reactions and proton coupled electron transfer, our review covers systems that produce proton motive force.     

Photoelectric performance of bacteria photosynthetic proteins entrapped on tailored mesoporous WO3-TiO2 films

Novel three-dimensional wormlike mesoporous WO(3)-TiO(2) films with tailored pore size (approximately 7.1 nm) were applied to prepare the bio-photoelectrodes (Bio-PEs) through direct entrapping the bacteria photosynthetic reaction center (RC) proteins. These mesoporous WO(3)-TiO(2) films exhibited unique characteristics in the specific loading of RC with high activity retained. Moreover, well-matched energy levels of WO(3)-TiO(2) and RC contributed to the photoelectric performance, especially in the red to near-infrared (NIR) region, of the derived Bio-PEs. Such strategy of manipulating the Bio-PEs based on well-designed mesoporous metal oxides and RC provides an alternative system to probe the photoinduced multiple-pathway electron transfer of photosensitive chromophores, which may open a new perspective to develop versatile bio-photoelectric devices.     

Electron transfer kinetics in photosynthetic reaction centers embedded in polyvinyl alcohol films

The coupling between electron transfer and protein dynamics has been studied at room temperature in isolated reaction centers (RCs) from the photosynthetic bacterium Rhodobacter sphaeroides by incorporating the protein in polyvinyl alcohol (PVA) films of different water/RC ratios. The kinetic analysis of charge recombination shows that dehydration of RC-containing PVA films causes reversible, inhomogeneous inhibition of electron transfer from the reduced primary quinone acceptor (Q(A)(-)) to the secondary quinone Q(B). A more extensive dehydration of solid PVA matrices accelerates electron transfer from Q(A)(-) to the primary photooxidized electron donor P(+). These effects indicate that incorporation of RCs into dehydrated PVA films hinders the conformational dynamics gating Q(A)(-) to Q(B) electron transfer at room temperature and slows down protein relaxation which stabilizes the primary charge-separated state P(+)Q(A)(-). A comparison with analogous effects observed in trehalose-coated RCs suggests that protein motions are less severely reduced in PVA films than in trehalose matrices at comparable water/RC ratios.     

叶绿素衍生物的合成及其对紫细菌原初光化学特性 的影响研究

对10个叶绿素衍生物的合成方法进行了研究,在一定的温度(43.5℃)和丙酮的协同作用下,植物脱镁叶绿素a可转换紫细菌RS601光合反应中心的细菌脱镁叶绿素,光化学活性为对照的71.4%,光化学活性的下降与替代色素的变化无对应关系,替代后降低了Bphe^-/Bphe和QA^-/QA电对之间的电子传递速率。     

Magnetic field effects on the recombination of radical ions in reaction centers of photosynthetic bacteria

The amount of triplet products formed upon recombination of the bacteriochlorophyll dimer cation and the bacteriopheophytin anion in modified bacterial reaction centres can be manipulated by external magnetic fields. Making use of this effect, two methods provide information about structural and dynamic properties of the reaction centre. The two methods differ in that one (MARY) uses low static magnetic fields (0 ? B₀ < 1 kG) whereas the other (RYDMR) uses microwaves and high static fields (B₀ > 1 kG). As is shown here the two methods are equivalent from a theoretical point of view, the interpretation of experimental spectra being equally involved in both cases.     

Adsorption-driven photocatalytic activity of mesoporous titanium dioxide

Titanium dioxide with a mesoporous structure, when photoactivated in water, demonstrates an unprecedented photocatalytic activity, driven strongly by an adsorption degree of molecules onto the catalyst surface, which promotes a preferential conversion of a well-adsorbed molecule. This catalyzes a selective transformation of a well-adsorbed molecule into a less-adsorbed molecule, so-labeled "stick-and-leave" transformation, which promotes a direct hydroxylation of benzene to phenol, one of the most difficult synthetic reactions, with very high selectivity (>80%) and using water as a source of oxidant.     

Photocatalytic lithography based on thin films of amorphous hydrated titanium dioxide

The mechanism of photoactivation of amorphous hydrated titanium dioxide thin films containing palladium ions toward the reaction of electroless deposition of nickel was studied. It was shown that the photocatalytic reduction of palladium ions during UV irradiation results in the formation of intermediate Pd(I) states that subsequently disproportionate, yielding a Pd nanophase. The palladium nanoparticle-catalyzed electroless deposition of nickel on exposed areas of the titanium dioxide photolayer makes it possible to fabricate metal patterns having a 5-μm resolution, with the fast and irreversible capture of photoelectrons at the latent image formation step preventing the image from blurring, including the process on conducting substrates.     

High-performance titanium dioxide photocatalyst on ordered mesoporous carbon support

Anatase TiO₂ photocatalysts supported with the ordered mesoporous carbon, CMK-3, were synthesized by the incorporation of TiO₂ into CMK-3 followed by heating at 700 °C. The structural properties of the TiO₂ on CMK-3 were investigated by X-ray diffraction, nitrogen physisorption and electron microscopy techniques. In particular, TiO₂ was observed both inside and the external surface of CMK-3. The photocatalytic activity of TiO₂ on CMK-3 under UV-light exhibited higher efficiency in removing the Rhodamine 6G dye solution than the commercial photocatalyst P25 and TiO₂ on activated carbon. It was attributed to the synergistic effect of large surface area adsorption provided by mesoporous CMK-3 and the distinctive location of TiO₂ on the external surface of CMK-3.     

Sonochemical fabrication of fluorinated mesoporous titanium dioxide microspheres

A sonochemical-hydrothermal method for preparing fluorinated mesoporous TiO₂ microspheres was developed. Formation of mesoporous TiO₂ and doping of fluorine was achieved by sonication and then hydrothermal treatment of a solution containing titanium isopropoxide, template, and sodium fluoride. The as-synthesized TiO₂ microspheres were characterized by X-ray diffraction (XRD), Fourier translation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray (EDX) spectroscopy, photoluminescence spectroscopy (PL), and BET surface areas. The P123 template was removed completely during the hydrothermal and washing steps, which was different from the conventional calcination treatment. The as- synthesized TiO₂ microspheres had good crystallinity and high stability. Results from the photocatalytic degradation of methylene blue (MB) showed that fluorination could remarkably improve the photocatalytic activity of titanium dioxide.     

Inter- and intraspecific variation in excited-state triplet energy transfer rates in reaction centers of photosynthetic bacteria

In protein-cofactor reaction center (RC) complexes of purple photosynthetic bacteria, the major role of the bound carotenoid (C) is to quench the triplet state formed on the primary electron donor (P) before its sensitization of the excited singlet state of molecular oxygen from its ground triplet state. This triplet energy is transferred from P to C via the bacteriochlorophyll monomer B(B). Using time-resolved electron paramagnetic resonance (TREPR), we have examined the temperature dependence of the rates of this triplet energy transfer reaction in the RC of three wild-type species of purple nonsulfur bacteria. Species-specific differences in the rate of transfer were observed. Wild-type Rhodobacter capsulatus RCs were less efficient at the triplet transfer reaction than Rhodobacter sphaeroides RCs, but were more efficient than Rhodospirillum rubrum RCs. In addition, RCs from three mutant strains of R. capsulatus carrying substitutions of amino acids near P and B(B) were examined. Two of the mutant RCs showed decreased triplet transfer rates compared with wild-type RCs, whereas one of the mutant RCs demonstrated a slight increase in triplet transfer rate at low temperatures. The results show that site-specific changes within the RC of R. capsulatus can mimic interspecies differences in the rates of triplet energy transfer. This application of TREPR was instrumental in defining critical energetic and coupling factors that dictate the efficiency of this photoprotective process.     

Self-assembling photosynthetic reaction centers on electrodes for current generation

Photosynthetic reaction centers (RCs) made from photosynthetic organisms can be used in solar batteries because their molecules cause light-induced charge separation. We present a simple immobilization system of the intact RCs from Rhodobacter sphaeroides on an electrode that uses nickel ligand binding by the hexameric histidine tag on H subunit (HHisRC). The binding constant of HHisRC to the nickel-nitrilotriacetic acid (Ni−NTA) chip measured with a surface plasmon resonance instrument was 1.6×10⁸M⁻¹. HHisRCs were immobilized on an indium tin oxide electrode overlaid with an Ni−NTA gold substrate. The photoinduced displacement current of this electrode was measured to estimate the orientation of HHisRC on the electrode, and the detachability of HHisRC from the electrode was determined by using an imidazole solution wash. The direction of the flash-light-induced displacement current suggested that the H subunit side of the immobilized HHisRC faced the surface of the electrode. The photoinduced current disappeared after the electrode was washed in the imidazole solution. This simple immobilization and detachment of HHisRC to the electrode might be useful for making a reproducible photocurrent device.     

Fe-doped and Mn-doped titanium dioxide thin films

Thin films of TiO₂ doped with Fe and Mn were deposited on F-doped SnO₂-coated glass by spin coating. Dopant concentrations of 3–7 wt% (metal basis) were used. The structural, chemical, and optical characteristics of the films were investigated. Laser Raman microspectroscopy and glancing angle X-ray diffraction data showed that the films consisted of the anatase polymorph of TiO₂. X-ray photoelectron spectroscopy data indicated the presence of Fe³⁺, Mn⁴⁺, and Mn³⁺ in the doped films, as predicted by calculated thermodynamic stability diagrams, and the occurrence of atomic disorder and associated structural distortion. Ultraviolet–visible spectrophotometry data showed that the optical indirect band gap of the films decreased significantly with increasing dopant levels, from 3.36 eV (undoped) to 2.95 eV (7 wt% Fe) and 2.90 eV (7 wt% Mn). These improvements are attributed to single (Fe) or multiple (Mn) shallow electron/hole trapping sites associated with the dopant ions.     

Self-assembly and sensor response of photosynthetic reaction centers on screen-printed electrodes

Photosynthetic reaction centers were immobilized onto gold screen-printed electrodes (Au-SPEs) using a self-assembled monolayer (SAM) of mercaptopropionic acid (MPA) which was deliberately defective in order to achieve effective mediator transfer to the electrodes. The pure Photosystem II (PS II) cores from spinach immobilize onto the electrodes very efficiently but fair badly in terms of photocurrent response (measured using duroquinone as the redox mediator). The cruder preparation of PS II known as BBY particles performs significantly better under the same experimental conditions and shows a photocurrent response of 20-35 nA (depending on preparation) per screen-printed electrode surface (12.5mm(2)). The data was corroborated using AFM, showing that in the case of BBY particles a defective biolayer is indeed formed, with grooves spanning the whole thickness of the layer enhancing the possibility of mass transfer to the electrodes and enabling biosensing. In comparison, the PS II core layer showed ultra-dense organization, with additional formation of aggregates on top of the single protein layer, thus blocking mediator access to the electrodes and/or binding sites. The defective monolayer biosensor with BBY particles was successfully applied for the detection of photosynthesis inhibitors, demonstrating that the inhibitor binding site remained accessible to both the inhibitor and the external redox mediator. Biosensing was demonstrated using picric acid and atrazine. The detection limits were 1.15 nM for atrazine and 157 nM for picric acid.     

Conformational control of cofactors in nature--functional tetrapyrrole conformations in the photosynthetic reaction centers of purple bacteria

Chemically identical tetrapyrrole cofactors such as hemes and chlorophylls participate in functionally diverse biological roles. An analysis of the available protein structural data for the bacteriochlorophylls in the photosynthetic reaction center gives statistically reliable evidence of the hypothesis that the protein induced cofactor conformation is a modulator of the bio-molecular function of each reaction center. The results serve as a general model to illustrate conformational control of tetrapyrrole cofactors in other proteins.     

Visible-light induced hydrophilicity on nitrogen-substituted titanium dioxide films

Nitrogen-substituted titanium dioxide thin films were found to undergo hydrophilic conversion under irradiation with visible light. The hydrophilicity was enhanced by increasing the degree of nitrogen substitution at oxygen sites. The water contact angle for the thin film with the greatest hydrophilicity, TiO1.9884N0.0116, changed from 20 degrees to 6 degrees following irradiation.