Cellulose II nanoelements prepared from fully mercerized, partially mercerized and regenerated celluloses by 4-acetamido-TEMPO/NaClO/NaClO2 oxidation

A softwood bleached kraft pulp (SBKP) and cotton lint cellulose were fully or partially mercerized, and these along with celluloses and commercially available regenerated cellulose fiber and beads were oxidized by 4-acetamido-TEMPO/NaClO/NaClO₂ at 60 °C and pH 4.8. Weight recovery ratios and carboxylate contents of the oxidized celluloses were 65–80% and 1.8–2.2 mmol g⁻¹, respectively. Transparent and viscous dispersions were obtained by mechanical disintegration of the TEMPO-oxidized celluloses in water. These aqueous dispersions showed birefringence between cross-polarizers, indicating that mostly individualized cellulose nanoelements dispersed in water were obtained by these procedures. Transmission electron microscopy observation showed that the cellulose nanoelements prepared from mercerized SBKP, repeatedly mercerized SBKP, mercerized cotton lint cellulose, regenerated cellulose beads and 18% NaOH-treated SBKP, i.e. partially mercerized SBKP, had similar morphologies and sizes, 4–12 nm in width and 100–200 nm in length. The 18% NaOH-treated SBKP was converted to cellulose nanoelements consisting of both celluloses I and II.     

TEMPO/NaBr/NaClO and NaBr/NaClO oxidations of cotton linters and ramie cellulose samples

Dried cotton linters and ramie cellulose samples were oxidized with 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)/NaBr/NaClO and NaBr/NaClO (i.e., TEMPO-free) in water at pH 10. The carboxy contents, degrees of polymerization (DPs), X-ray diffraction patterns, and solid-state ¹³C NMR spectra were measured or obtained for the oxidized products with and without subsequent NaBH₄ reduction. Cellulose nanofibrils were prepared from the oxidized cellulose samples by sonication in water and observed by atomic force microscopy and transmission electron microcopy. Because the cellulose molecules were depolymerized with NaBr/NaClO, the depolymerization behavior of the cellulose samples with TEMPO/NaBr/NaClO can be mainly explained by depolymerization with NaBr/NaClO (i.e., not TEMPO-related compounds or reactions). However, because C6-aldehydes formed in the disordered regions periodically present along the longitudinal direction of each cellulose microfibril, the viscosity-average DP values of the TEMPO/NaBr/NaClO-oxidized cellulose samples decreased to 200–300, while those with subsequent NaBH₄ reduction exhibited much higher DP values. The nanofibrils prepared from the TEMPO/NaBr/NaClO-oxidized cellulose samples had smallest fibril heights or widths of 5–6 nm. However, significant amounts of unfibrillated bundles with heights of 10–40 mm were present in the nanofibril/water dispersions. The high carboxy contents of the TEMPO/NaBr/NaClO-oxidized cellulose samples (1.62–1.63 mmol/g) indicated that significant amounts of carboxy groups were likely present in the disordered regions, probably forming tail-like polyglucuronate chains. Solid-state ¹³C NMR analysis revealed that some of the glucosyl units originally with the tg C6–OH conformation were transformed to other conformations by TEMPO/NaBr/NaClO oxidation, while the crystalline C4 signal areas remained constant.

Graphic abstract

     

Oxidation of wood cellulose using 2-azaadamantane N-oxyl (AZADO) or 1-methyl-AZADO catalyst in NaBr/NaClO system

A wood cellulose was oxidized with catalytic amounts of 2-azaadamantane N-oxyl (AZADO) or 1-methyl-AZADO, in an NaBr/NaClO system, in water at pH 10. The oxidation efficiency, carboxylate/aldehyde contents, and degree of polymerization (DP_v) of the oxidized celluloses thus obtained were evaluated in terms of the amount of AZADO or 1-methyl-AZADO catalyst added, in comparison with those prepared using the TEMPO/NaBr/NaClO system. When the AZADO/NaBr/NaClO and 1-methyl-AZADO/NaBr/NaClO oxidation systems were applied to wood cellulose using the same molar amount of TEMPO, the oxidation time needed for the preparation of oxidized celluloses with carboxylate contents of 1.2–1.3 mmol/g was reduced from ≈80 to 10–15 min. Moreover, the molar amounts of AZADO and 1-methyl-AZADO that had to be added for the preparation of oxidized celluloses with carboxylate contents of 1.2–1.3 mmol/g were reduced to 1/32 and 1/16 of the amount of TEMPO added, respectively. The DP_v values for the AZADO- and 1-methyl-AZADO-oxidized celluloses after NaBH₄ treatment were in the range of 600–800. This indicated that not only C6-carboxylate groups but also C2/C3 ketones were formed to some extent on the crystalline cellulose microfibril surfaces during the AZADO- and 1-methyl-AZADO-mediated oxidation. When the AZADO-oxidized wood cellulose, which had a carboxylate content of 1.2 mmol/g, was mechanically disintegrated in water, an almost transparent dispersion consisting of individually nano-dispersed oxidized cellulose nanofibrils was obtained, with a nanofibrillation yield of 89 %.     

Immobilization of cellulose extracted from Robinia Pseudoacacia seed fibers onto chitosan: Chemical characterization and study of methylene blue removal

The design of economical adsorbents to remove pollutants from contaminated water is attracting more attention. In this study, cellulose was successfully extracted from Robinia Pseudoacacia seed fibers and immobilized onto chitosan beads. The prepared spherical beads were then used for the biosorption of methylene blue dye from aqueous media. Samples were investigated using several analytical methods, namely FT-IR, XRD, EDX, SEM, and TGA analyses. The adsorption experiments showed that combining cellulose with chitosan improved the removal of methylene blue. The maximum uptake amount of methylene blue using cellulose–chitosan composite beads was 55 mg/g. However, it was about 35 mg/g at 20 °C for chitosan beads. The kinetic data complied strongly with the pseudo-second order equation, suggesting that the biosorption phenomenon has predominantly a chemical nature. Overall, the current study has shown a promising technique to design new adsorbents from abundant natural polymers for eliminating cationic dyes from water.     

Adsorption of a cationic surfactant onto cellulosic fibers I. Surface charge effects

The adsorption of four cationic surfactants with different alkyl chain lengths on cellulose substrates was investigated. Cellulose fibers were used as model substrates, and primary alcohol groups of cellulose glycosyl units were oxidized into carboxylic groups to obtain substrates with different surface charges. The amount of surfactant adsorbed on the fiber surface, the fiber zeta-potential, and the amount of surfactant counterions (Cl(-)) released into solution were measured as a function of the surfactant bulk concentration, its molecular structure, the substrate surface charge, and the ionic strength. The contribution of each of these parameters to the shape of the adsorption isotherms was used to verify if surfactant adsorption and self-assembly models usually used to describe the behavior of surfactant/oxide systems can be applied, and with which limitations, to describe cationic surfactant adsorption onto oppositely charged cellulose substrates.     

Adsorption and viscoelastic properties of cationic xylan on cellulose film using QCM-D

The adsorption and viscoelastic properties of cationic xylan layers adsorbed from an aqueous electrolyte solution (NaCl 0, 1, 10, 100 mM) on a cellulose model surface were studied using quartz crystal microbalance with dissipation (QCM-D). Three cationic xylans with different charge densities were used (molecular weight, 9,600 g/mol with degrees of substitution, DS = 0.150, 0.191, and 0.259). The influences of the electrolyte concentration and charge density of cationic xylan on its adsorption onto a cellulose surface were investigated. Low charged cationic xylan was substantially more efficient in surface adsorption on cellulose compared to high charged cationic xylan at a low concentration of electrolytes. Adsorption of low charged cationic xylan decreased with increases in electrolyte concentration. However, adsorption of high cationic xylan increased with electrolyte concentration. The conformation and viscoelastic properties of the layers were interpreted by modeling the data under the assumption that the layers can be explained by the a Voigt model. Low charged cationic xylan adsorbed relatively weakly onto the cellulose surface, and formed a thicker, softer layer than high charged cationic xylan. On the other hand, high charged cationic xylan formed a thinner adsorption layer onto the cellulose surface.     

Adsorption behavior of water soluble polymers with lower critical solution temperature

The adsorption behavior of hydroxylpropyl cellulose (HPC), ethyl hydroxylethyl cellulose (EHEC) and poly-vinylalcohol (PVA) polymers, which have a lower critical solution temperature (LCST), have been studied in comparison with the behavior of hydroxylethyl cellulose (HEC) with no LCST. The saturated amount of adsorption (A _s ) for the polymers with LCST depended significantly on the adsorption temperature and theA _s , e. g., for HPC obtained at the LCST, the amount was 1.5 times as large as the value at room temperature. The highA _s values obtained at the LCST were maintained over a long period at room temperature, and the dense adsorption layer formed on the latex particles at the LCST showed a strong protective action against flocculation. Furthermore, the effect of the surface nature of the adsorbent on the polymer adsorption at the LCST has been investigated using six kinds of synthetic latices with different surface natures. It was found that the hydrophobic interaction between the polymer and the adsorbent plays an important role in inducing the adsorption, and the trend of increasing the hydrophilic character of the latex surface prevents the formation of the adsorption layer of the polymer.     

TEMPO-Oxidized Cellulose Beads as Potential pH-Responsive Carriers for Site-Specific Drug Delivery in the Gastrointestinal Tract

The development of controlled drug delivery systems based on bio-renewable materials is an emerging strategy. In this work, a controlled drug delivery system based on mesoporous oxidized cellulose beads (OCBs) was successfully developed by a facile and green method. The introduction of the carboxyl groups mediated by the TEMPO(2,2,6,6-tetramethylpiperidine-1-oxyradical)/NaClO/NaClO₂ system presents the pH-responsive ability to cellulose beads, which can retain the drug in beads at pH = 1.2 and release at pH = 7.0. The release rate can be controlled by simply adjusting the degree of oxidation to achieve drug release at different locations and periods. A higher degree of oxidation corresponds to a faster release rate, which is attributed to a higher degree of re-swelling and higher hydrophilicity of OCBs. The zero-order release kinetics of the model drugs from the OCBs suggested a constant drug release rate, which is conducive to maintaining blood drug concentration, reducing side effects and administration frequency. At the same time, the effects of different model drugs and different drug-loading solvents on the release behavior and the physical state of the drugs loaded in the beads were studied. In summary, the pH-responsive oxidized cellulose beads with good biocompatibility, low cost, and adjustable release rate have shown great potential in the field of controlled drug release.     

Characterization of cellulose nanofibrils prepared by direct TEMPO-mediated oxidation of hemp bast

Hemp bast (α-cellulose 79.4%, Klason lignin 4.9%) was directly oxidized by 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation in water at pH 10 and room temperature for 2 h. The level of added NaClO in oxidation varied from 5 to 30 mmol/g (based on dry weight of hemp bast). Weight recovery ratios of the TEMPO-oxidized hemp bast celluloses were in the range of 81–91%, and their carboxylate contents increased up to 1.2 mmol/g with the increased NaClO addition level. The lignin contents decreased to 0.5–0.9% after oxidation, and the viscosity-average degrees of polymerization decreased from 1100 to 560 because of depolymerization during oxidation. Thus, direct TEMPO-mediated oxidation of hemp bast introduced a significant number of carboxylate groups and simultaneously achieved sufficient delignification. Small amounts of xylose, mannose, and rhamnose originating from hemicelluloses remained in the TEMPO-oxidized hemp bast samples prepared by oxidation with 5–20 mmol/g NaClO. However, oxidation with 30 mmol/g NaClO completely removed these hemicellulose-originating sugars, and produced almost pure TEMPO-oxidized cellulose. When TEMPO-oxidized hemp bast samples were mechanically disintegrated in water, their nanofibrillation yields were 58–65%. After removal of unfibrillated fractions by centrifugation, transparent dispersions showed birefringence when observed between cross-polarizers, while atomic force microscopy images showed near-individually dispersed nanofibril elements with widths of ~2 nm.     

The potential of TEMPO-oxidized nanofibrillar cellulose beads for cell delivery applications

The advanced development of cell carriers for regenerative medicine and cell therapy demands materials able to sustain cell viability prior to their delivery to the target tissue, an ability that can be controlled by the shape, size and degradability of the matrix. TEMPO-oxidized nanofibrillar cellulose (ToNFC) macromolecules are negatively charged and therefore can be easily formulated by ionotropic gelation into beads of varying sizes that can release their payload through an erosion-controlled process. We report here for the first time on the preparation of ToNFC beads via ionic gelation using CaCl₂ and on their loading with OSTEO-1 rat bone cells, with a view to examine their capacity of sustaining the cell viability and of releasing the bone cells in a controlled manner. The initial results obtained demonstrate that ToNFC is able to protect the OSTEO-1 cells and to maintain their viability for at least 2 weeks. Following gradual disintegration of the beads, a significant cell release and subsequent proliferation was observed after 7 days. These results indicate the considerable potential of nanofibrillar cellulose (ToNFC) for applications in cell therapy and regenerative medicine.     

Self-aggregation of cationic surfactants onto oxidized cellulose fibers and coadsorption of organic compounds

In this work, the adsorption of cationic surfactant and organic solutes on oxidized cellulose fibers bearing different amounts of carboxylic moieties was investigated. The increase in the amount of -COOH groups on cellulose fibers by TEMPO oxidation induced a general rise in surfactant adsorption. For all tested conditions, that is, cellulose oxidation level and surfactant alkyl chain length (C12 and C16), adsorption isotherms displayed a typical three-region shape with inversion of the substrate zeta-potential which was interpreted as reflecting surfactant adsorption and aggregation (admicelles and hemimicelles) on cellulose fibers. The addition of organic solutes in surfactant/cellulose systems induced a decrease in surfactant cac on the cellulose surface thus favoring surfactant aggregation and the formation of mixed surfactant/solute assemblies. Adsorption isotherms of organic solutes on cellulose in surfactant/cellulose/solute systems showed that solute adsorption is strictly correlated to (i) the surfactant concentration, solute adsorption increases up to the surfactant cmc, where solute partitioning between the cellulose surface and free micelles causes a drop in adsorption, and to (ii) solute solubility and functional groups. The specific shape of solutes adsorption isotherms at a fixed surfactant concentration was interpreted using a Frumkin adsorption isotherm, thus suggesting that solute uptake on cellulose fibers is a coadsorption and not a partitioning process. Results presented in this study were compared with those obtained in a previous work investigating solute adsorption in anionic surfactant/cationized cellulose systems to better understand the role of surfactant/solute interactions in the coadsorption process.     

Physical properties of TEMPO-oxidized bacterial cellulose nanofibers on the skin surface

Water-dispersed bacterial cellulose nanofibers were prepared via an oxidation reaction using 2,2,6,6-tetramethyl-1-piperidine-N-oxy radical (TEMPO) as a catalyst. It was found that TEMPO-oxidized bacterial cellulose nanofibers (TOCNs) synthesized via sodium bromide-free methods are similar to those synthesized using sodium bromide. The TOCNs retained their unique structure in water as well as in emulsion. TOCNs adhere to the skin surface while maintaining nanofibrous structures, providing inherent functions of bacterial cellulose, such as high tensile strength, high water-holding capacity, and blockage of harmful substances. When gelatin gels as model skin were coated with TOCNs, the hardness representing the elasticity was increased by 20% compared to untreated gelatin gel because TOCNs could tightly hold the gelatin structure. When porcine skin was treated with TOCNs, carboxymethyl cellulose, and hydroxyethyl cellulose, the initial water contact angles were 26.5°, 76.5°, and 64.1°, respectively. The contact angle of TOCNs dramatically decreased over time as water penetrated the fibrous structure of the TOCN film. When observed by scanning electron microscopy and confocal microscopy, TOCNs on the skin surface provided physical gaps between particles and the skin, blocking the adsorption of particulate matter to the skin surface. On the contrary, the structure of water-soluble polymers was disrupted by an external environment, such as water, so that particulate matter directly attached to the skin surface. Characterization of TOCNs on the skin surface offered insight into the function of nanofibers on the skin, which is important for their applications with respect to the skin and biomedical research.     

Selective oxidation of cellulose catalyzed by NHPI/Co(OAc)2 using air as oxidant

With NHPI/Co(OAc)₂ as catalyst and air as oxidant, carboxylic group functionalized cellulose was prepared by oxidation of cellulose in acetic acid. Fourier transform infrared spectroscopy was utilized to detect the generation of carboxylic group and the acid amount was determined by acid–base titration method. The present results revealed that C6 primary hydroxyl groups on glucose units were partly converted to carboxylic groups during the catalytic oxidation process. The degree of polymerization of oxidized cellulose, which was determined by viscosity measurement, decreased slightly as compared with its parent. The structure of cellulose was characterized by X-ray diffraction and scanning electron microscopy, and it was almost unchanged.     

The role of mild TEMPO–NaBr–NaClO oxidation on the wet adhesion of regenerated cellulose membranes with polyvinylamine

X-ray Photoelectron Spectroscopy (XPS) was used to characterize the functional groups present on regenerated cellulose films after mild oxidation with TEMPO–NaBr–NaClO and the results were correlated with the adhesion forces holding together two wet cellulose films laminated with a thin (i.e. less than 10 mg/m²) layer of polyvinylamine (PVAm). There was no correlation between adhesion and carboxyl content, whereas wet adhesion was proportional to the total content of aldehyde and hemiacetal groups on the cellulose. It is proposed that aldehyde groups react with neighboring cellulose chains to form hemiacetals which serve as crosslinks strengthening the cellulose surface. The hemiacetals can also be attacked by primary amines to give imine and aminal covalent linkages to the PVAm adhesive layer.     

Thermal stabilization of TEMPO-oxidized cellulose

A partially C6-carboxylated cellulose with carboxylate content of 1.68 mmol/g was prepared by 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation of a softwood bleached kraft pulp. Thermogravimetric analyses of the TEMPO-oxidized cellulose (TOC) and its related materials were studied to improve thermal stability of the TOC. Thermal decomposition (T_d) points of the TOC with sodium carboxylate groups, alkali-treated TOC with free carboxyl groups of 0.23 mmol/g and the original cellulose were 222 °C, 264 °C and 275 °C, respectively. Thus, the anhydroglucuronic acid units formed by TEMPO-mediated oxidation of the native wood cellulose and present in the TOC cause the decrease in T_d point by decarbonation during heating process. When carboxyl groups in the TOC were methylated with trimethylsilyl diazomethane (TMSCHN₂), the T_d point increased from 222 °C to 249 °C, and the peak temperature in its derivative thermogravimetric (DTG) curve increased from 273 °C to 313 °C, which was almost equal to that of the original cellulose. Thus, the methyl esterification of carboxyl groups in the TOC is effective in improving thermal stability. When sodium ions present in the TOC as counter ions of carboxylate groups were exchanged to some other metal ions, thermal stability was improved to some extent. Especially, when CaCl₂, Ca(OAc)₂, Ca(NO₃)₂ and CaI₂ solutions were used in the ion-exchange treatments, the peak temperatures in the DTG curves increased to approximately 300 °C. MgCl₂, NiCl₂, SrCl₂ and Sr(OAc)₂ solutions were also effective to some extent in increasing the peak temperatures of DTG curves. Thus, thermal stability of the fibrous TOC can be improved to some extent by methyl esterification of the sodium carboxylate groups present in the original TOC with TMSCHN₂ or ion-exchange treatments with some metal salt solutions.     

Removal of Toxic As (V) Ions by Adsorption onto Alginate and Carboxymethyl Cellulose Beads

The removal of arsenic ions from dilute aqueous solutions using biopolymeric beads of crosslinked sodium alginate and carboxymethyl cellulose (CMC) as the adsorbent is reported in this paper. The biopolymeric alginate and carboxymethyl cellulose beads were prepared and characterized by FTIR spectra. On the surfaces of the prepared beads were performed static and dynamic adsorption studies of arsenic ions at fixed pH and ionic strength of the aqueous metal ion solutions. The adsorption data were applied to Langmuir and Freundlich isotherm equations and various static parameters were calculated. The dynamic nature of adsorption was quantified in terms of several kinetic constants such as rate constant for adsorption (k₁) and Lagergreen rate constant (K_ad). The influence of various experimental parameters such as solid to liquid ratio, pH, temperature, presence of salts and chemical composition of biopolymeric beads were investigated on the adsorption of arsenic ions.     

Adsorption of cationic cellulose derivative/anionic surfactant complexes onto solid surfaces. II. Hydrophobized silica surfaces

The effect of the anionic surfactant SDS (sodium dodecyl sulfate) on the adsorption behavior of cationic hydroxyethyl cellulose (Polymer JR-400) and hydrophobically modified cationic cellulose (Quatrisoft LM-200) at hydrophobized silica has been investigated by null ellipsometry and compared with the previous data for adsorption onto hydrophilic silica surfaces. The adsorbed amount of LM-200 is found to be considerably larger than the adsorbed amount of JR-400 at both surfaces. Both polymers had higher affinity toward hydrophobized silica than to silica. The effect of SDS on polymer adsorption was studied under two different conditions: adsorption of polymer/SDS complexes from premixed solutions and addition of SDS to preadsorbed polymer layers. Association of the surfactant to the polymer seems to control the interfacial behavior, which depends on the surfactant concentration. For the JR-400/SDS complex, the adsorbed amount on hydrophobized silica started to increase progressively from much lower SDS concentrations, while the adsorbed amount on silica increased sharply only slightly below the phase separation region. For the LM-200/SDS complex, the adsorbed amounts increased progressively from very low SDS concentrations at both surfaces, and no large difference in the adsorption behavior was observed between two surfaces below the phase separation region. The complex desorbed from the surface at high SDS concentrations above the critical micelle concentration. The reversibility of the adsorption of polymer/SDS complexes upon rinsing was also investigated. When the premixed polymer/SDS solutions at high SDS concentrations (>5 mM) were diluted by adding water, the adsorbed amount increased due to the precipitation of the complex. The effect of the rinsing process on the adsorbed layer was determined by the hydrophobicity of the polymer and the surface.     

Mechanism and kinetics studies of carboxyl group formation on the surface of cellulose fiber in a TEMPO-mediated system

2,2,6,6-Tetramethylpiperidine-1-oxyl radical (TEMPO) can selectively oxidize primary hydroxyl groups of cellulose to carboxyl groups. However, the depolymerization also occurs during the process. The kinetics and mechanism of carboxyl group formation on the surface of cellulose fiber oxidized by TEMPO/NaClO₂/NaClO were discussed. The oxidization and depolymerization of cellulose occurred simultaneously, according to analysis of FTIR and ¹³C CP/MAS NMR. The glucuronic acid and some small molecular fragments, formed by hydrolysis or β-elimination during the oxidation, are also discussed. The crystallization index increased and crystal size decreased, as shown by X-ray analysis. The degradation steps in the TEMPO/NaClO₂/NaClO system was discussed, according to carbon conversion analyzed by ¹³C CP/MAS NMR. The oxidation of cellulose can be described well by the kinetics model established based on the degradation of cellulose. It was found that temperature is one of the key parameters for controlling the oxdation and degradation level. The possible mechanism for oxidation of cellulose was composed.     

Rheological properties of nanocellulose suspensions: effects of fibril/particle dimensions and surface characteristics

The rheological properties of aqueous suspensions based on three different nanocelluloses were compared. One system was obtained via acid hydrolysis (thus yielding crystalline nanocellulose, CNC) and the other two from mechanical shearing, but from different origins and subjected to different pretreatments. Of the latter two, one was considered to be a rather typical cellulose nanofibril (CNF) suspension whereas the other was a kind of intermediate between CNF and CNC. All three nanocellulose elements differed in dimensions as evident from transmission electron microscopy and atomic force microscopy. With regard to the length of the fibrils/particles, the three nanocelluloses formed three distinct groups with lengths between 200 and slightly more than 800 nm. The three cellulosic elements were also subjected to a TEMPO-mediated oxidation yielding a similar carboxylate content in the three systems. Furthermore, the TEMPO-oxidized elements were grafted with poly(ethylene glycol) (PEG). The amount of grafted PEG was about 35 wt%. The shear viscosity, the storage modulus and the loss modulus of suspensions of the unmodified, the TEMPO-oxidized and the grafted nanocelluloses were determined at room temperature and the solids content of the suspensions was varied between 0.7 and 2.0 wt%. It was concluded that the rheological properties varied significantly between the suspensions depending on the dimensions of the cellulosic elements and their surface characteristics. In this context, the length (or the aspect ratio) of the particles played a very important role.     

Surface characterization of stepwise oxidized spruce thermomechanical pulp samples by different analytical methods

An investigation of the fiber samples with various amounts of lignin, hemicelluloses and cellulose was conducted by means of dye adsorption, spectrometric and chemical analyses. Five fiber samples were prepared by the oxidation of unbleached Norway spruce thermo-mechanical pulp with acidic potassium permanganate solution. Each sample was oxidized with defined amount of KMnO₄ and the degree of oxidation was determined as kappa number. Fibers were additionally characterized by conductometric titration, the determination of hemicelluloses and infrared spectrometry. Sorption of various types of dye, namely Methylene Blue (MB), Crystal Violet (CV) and Astra Blue (AB) on the fiber surface was studied and compared to the kappa number and other fiber characteristics. The adsorption of MB and CV is found to follow the amount of anionic (carboxylic) groups, which at first increase and later decrease toward the final stages of oxidation. The behavior of AB is nearly the opposite, its adsorption increases with the depletion of lignin and carboxylate groups, pointing to a different mechanism of AB binding on fibers.