Fabrication of metal nanoparticles–carbon nanotubes composite materials in solution

A new solution-phase method for synthesis of metal nanoparticles–carbon nanotubes (CNTs) assemblies is described. By injection of CNTs solution into the diethyl ether/aqueous solution of metal salt biphasic mixture, metal (Ag, Au, Pd, and Pt) nanoparticles–decorated CNTs composite materials can be prepared. Metal nanoparticles have spontaneously and selectively formed on the sidewalls of CNTs through redox reaction between CNTs and metal ions. This phenomenon has been probed by transmission electron microscopy, scanning electron microscopy, energy dispersive X-ray analysis, and Raman spectroscopy.     

溶液体系中的纳米金属粒子形状控制合成*

纳米尺度的金属粒子由于量子尺寸效应等原因而表现出不同于宏观金属块体的电学、磁学、光学和热学等性质.纳米金属粒子的性质不仅受到尺寸的影响,还与粒子的形状密切相关.不同形状的纳米金属粒子通常具有不同的表面结构和性质.近年来,纳米金属粒子的形状控制合成正受到越来越多的关注;其中,Ⅷ族和IB族金属的研究已取得一定进展.本文评述了纳米金属粒子的合成以及尺寸和形状控制的方法,分别介绍了铂、钯、镍、金、银、铜以及钴等金属的形状控制合成的近期研究进展.     

Preparation and characterization of metal-chitosan nanocomposites

Various metal-chitosan nanocomposites were synthesized, including silver (Ag), gold (Au), platinum (Pt), and palladium (Pd) in aqueous solutions. Metal nanoparticles were formed by reduction of corresponding metal salts with NaBH4 in the presence of chitosan. And chitosan molecules adsorbing onto the surface of as-prepared metal nanoparticles formed the corresponding metal-chitosan nanocomposites. Transmission electron microscopy (TEM) images and UV-vis spectra of the nanocomposites revealed the presence of metal nanoparticles. Comparison of all the resulting particles size, it shows that silver nanoparticles are much larger than others (Au, Pt and Pd). In addition, the difference in particles size leads to develop different morphologies in the films cast from prepared metal-chitosan nanocomposites. Polarized optical microscopy (POM) images show a batonet-like structure for Ag-chitosan nanocomposites film, while for the films cast from other metal (Au, Pt, and Pd)-chitosan nanocomposites, some branched-like structures with a few differences among them were observed under POM observation.     

Rigid nanoscopic containers for highly dispersed, stable metal and bimetal nanoparticles with both size and site control

We demonstrate a novel strategy for the preparation of mesoporous silica-supported, highly dispersed, stable metal and bimetal nanoparticles with both size and site control. The supporting mesoporous silica, functionalized by polyaminoamine (PAMAM) dendrimers, is prepared by repeated Michael addition with methyl acrylates (MA) and amidation reaction with ethylenediamine (EDA), by using aminopropyl-functionalized mesoporous silica as the starting material. The encapsulation of metal nanoparticles within the dendrimer-propagated mesoporous silica is achieved by the chemical reduction of metal-salt-impregnated dendrimer-mesoporous silica by using aqueous hydrazine. The site control of the metal or bimetal nanoparticles is accomplished by the localization of inter- or intradendrimeric nanoparticles within the mesoporous silica tunnels. The size of the encapsulated nanoparticles is controlled by their confinement to the nanocavity of the dendrimer and the mesopore. For Cu and Pd, particles locate at the lining of mesoporous tunnels, and have diameters of less than 2.0 nm. For Pd/Pt, particles locate at the middle of mesoporous tunnels and have diameters in the range of 2.0-4.2 nm. The Pd and Pd/Pt nanoparticles are very stable in air, whereas the Cu nanoparticles are stable only in an inert atmosphere.     

In situ facile loading of noble metal nanoparticles on polydopamine nanospheres via galvanic replacement reaction for multifunctional catalysis

Noble metal nanoparticles(Pd,Ag,Pt,Au) with small and relatively uniform sizes were loaded on polydopamine nanospheres through in situ galvanic replacement reaction in aqueous solution.No additional reductant,surfactant or organic solvent was needed.X-ray photoelectron spectroscopy results revealed that the amount of quinone increased,while the amount of phenolic hydroxyl decreased on PDA nanospheres,indicating that the galvanic displacement reaction occurred between catechol groups and noble metal ions.The as-prepared PDA/Pd exhibited high catalytic activity and excellent stability in styrene hydrogenation.Moreover,PDA spheres retains the photo-thermal effect to serve as a nano-sized heater to accelerate the catalytic reactions under near-infrared illumination.     

A facile synthesis and characterization of Ag, Au and Pt nanoparticles using a natural hydrocolloid gum kondagogu (Cochlospermum gossypium)

An environmentally benign method for the synthesis of noble metal nanoparticles has been reported using aqueous solution of gum kondagogu (Cochlospermum gossypium). Both the synthesis, as well as stabilization of colloidal Ag, Au and Pt nanoparticles has been accomplished in an aqueous medium containing gum kondagogu. The colloidal suspensions so obtained were found to be highly stable for prolonged period, without undergoing any oxidation. SEM-EDXA, UV-vis spectroscopy, XRD, FTIR and TEM techniques were used to characterize the Ag, Au and Pt nanoparticles. FTIR analysis indicates that -OH groups present in the gum matrix were responsible for the reduction of metal cations into nanoparticles. UV-vis studies showed a distinct surface plasmon resonance at 412 and 525 nm due to the formation of Au and Ag nanoparticles, respectively, within the gum network. XRD studies indicated that the nanoparticles were crystalline in nature with face centered cubic geometry. The noble metal nanoparticles prepared in the present study appears to be homogeneous with the particle size ranging between 2 and 10 nm, as evidenced by TEM analysis. The Ag and Au nanoparticles formed were in the average size range of 5.5±2.5 nm and 7.8±2.3 nm; while Pt nanoparticles were in the size range of 2.4±0.7 nm, which were considerably smaller than Ag and Au nanoparticles. The present approach exemplifies a totally green synthesis using the plant derived natural product (gum kondagogu) for the production of noble metal nanoparticles and the process can also be extended to the synthesis of other metal oxide nanoparticles.     

Facile Synthesis of Gold Icosahedra in an Aqueous Solution by Reacting HAuCl4 with N‐Vinyl Pyrrolidone

Herein we describe a protocol that generates Au icosahedra in high yields by simply mixing aqueous solutions of HAuCl₄ and N‐vinyl pyrrolidone. Our mechanistic study reveals that water plays an important role in this synthesis: as a nucleophile, it attacks the gold–vinyl complex, leading to the production of an alcohol‐based Au^I intermediate. This intermediate then undergoes a redox reaction in which Au^I is reduced to Au⁰, leading to the formation of Au atoms and then Au icosahedra of about 18 nm in size at a yield of 94 %, together with a carboxylic acid in the final product. This new protocol has also been employed to prepare multiply twinned nanoparticles of Ag (15–20 nm in size), spherical aggregates (25–30 nm in size) of Pd nanoparticles, and very small nanoparticles of Pt (2 nm in size). Since no organic solvent, surfactant, or polymer stabilizer is needed for all these syntheses, this protocol may provide a simple, versatile, and environmentally benign route to noble‐metal nanoparticles having various compositions and morphologies.     

Platinum monolayer on nonnoble metal-noble metal core-shell nanoparticle electrocatalysts for O2 reduction

We synthesized a new class of O2 electrocatalysts with a high activity and very low noble metal content. They consist of Pt monolayers deposited on the surfaces of carbon-supported nonnoble metal-noble metal core-shell nanoparticles. These core-shell nanoparticles were formed by segregating the atoms of the noble metal on to the nanoparticles' surfaces at elevated temperatures. A Pt monolayer was deposited by galvanic displacement of a Cu monolayer deposited at underpotentials. The mass activity of all the three Pt monolayer electrocatalysts investigated, viz., Pt/Au/Ni, Pt/Pd/Co, and Pt/Pt/Co, is more than order of magnitude higher than that of a state-of-the-art commercial Pt/C electrocatalyst. Geometric effects in the Pt monolayer and the effects of PtOH coverage, revealed by electrochemical data, X-ray diffraction, and X-ray absorption spectroscopy data, appear to be the source of the enhanced catalytic activity. Our results demonstrated that high-activity electrocatalysts can be devised that contain only a fractional amount of Pt and a very small amount of another noble metal.     

Nanoporous Pt@Au(x)Cu(100-x) by hydrogen evolution assisted electrodeposition of Au(x)Cu(100-x) and galvanic replacement of Cu with Pt: electrocatalytic properties

Electrodeposition of high-surface-area nanoporous Au-Cu foams under conditions of hydrogen codeposition is studied. The honeycomb-like Au(x)Cu(100-x) foams with 0 ≤ x ≤ 100 are electrodeposited by controlling the amount of corresponding ions in the solution. The amount of metal ions in deposited films follows that in used electrolytes. Compared to monometallic foams, the Au(x)Cu(100-x) structures are characterized by smaller ligament or particle sizes (less than 10 nm) and improved stability. The addition of even a small amount of Cu to the Au matrix is found to dramatically improve the stability of the structure in air environment or an acidic medium. Pt@Au(x)Cu(100-x) structures are formed by the galvanic displacement of Cu from Au(x)Cu(100-x) templates. During the displacement of Cu by Pt, Au serves as a buffer, decreasing mechanical stresses and preventing the detachment of the foam from the substrate. The surface ratio of Pt to Au atoms is controlled by adjusting the amount of Cu in the template. Pt@Au(x)Cu(100-x) electrodes are investigated as novel electrocatalysts for methanol oxidation in alkaline media. The Au-enriched surfaces show higher catalytic activity toward methanol oxidation, while the electrodes with a higher amount of Pt are more stable.     

Formation of Metal Selenide and Metal–Selenium Nanoparticles using Distinct Reactivity between Selenium and Noble Metals

Small Se nanoparticles with a diameter of ≈20 nm were generated by the reduction of selenium chloride with NaBH₄ at ?10 °C. The reaction with Ag at 60 °C yielded stable Ag₂Se nanoparticles, which subsequently were transformed into M–Se nanoparticles (M=Cd, Zn, Pb) through cation exchange reactions with corresponding ions. The reaction with Pt formed Pt layers that were evenly coated on the surface of the Se nanoparticles, and the dissolution of the Se cores with hydrazine generated uniform Pt hollow nanoparticles. The reaction with Au generated tiny Au clusters on the Se surface, and eventually formed acorn‐shaped Au–Se nanoparticles through heat treatment. These results indicate that small Se nanoparticles with diameters of ≈20 nm can be used as a versatile platform for the synthesis of metal selenide and metal–selenium hybrid nanoparticles with complex structures.     

Bestimmung des oberflächensauerstoffs auf metallen durch aktivierung im reaktor

Surface oxygen on metal foils was determined by activation analysis on the basis of the reaction sequence ⁶Li(n,α)t, ¹⁶O(t,n) ¹⁸F. The metal foils were placed between foils consisting of lithium fluoride and polystyrene, sealed in evacuated ampoules, and irradiated in the reactor. The produced ¹⁸F was radiochemically separated, and measured by its annihilation radiation at 0.51 MeV. The overall cross-sections of such foil arrangements were computed by simple formulas and compared with experimental data. Instructions are given for the chemical treatment of irradiated foils of Au, Pt, Ni, Cu, Al, Fe and Zr. The following values of oxygen coverage were found on rolled foils; Pt 1.4, Ni 1.4, Cu 2.9, Al 4.9 and Fe 7.5 μg O/cm² of geometrical surface, Other oxygen values refer to Au, Zr and to different pretreatments of the metal surfaces. The lower limit of determination is about 0.1 μg O/cm².     

Different mechanisms govern the two-phase Brust-Schiffrin dialkylditelluride syntheses of Ag and Au nanoparticles

Here we report the first unambiguous identification of the chemical structures of the precursor species involving metal (Au and Ag) ions and Te-containing ligands in the Brust-Schiffrin syntheses of the respective metal nanoparticles, through which the different reaction pathways involved are delineated.     

Preparation of carbon-supported core-shell Au-Pt nanoparticles for methanol oxidation reaction: The promotional effect of the Au core

Core-shell Au-Pt nanoparticles with intimate contact of Pt and Au were prepared by a displacement reaction without formation of monometallic Au nanoparticles. The Au-Pt nanoparticles were dispersed on carbon (Au@Pt/C) and were used to catalyze methanol electrooxidation in acidic solutions at room temperature. The core-shell nanostructure was confirmed by transmission electron microscopy and X-ray photoelectron spectroscopy, and specific catalytic activities were evaluated by CO anodic stripping voltammetry in 0.5 M H(2)SO(4) and by cyclic voltammetry in 1 M CH(3)OH + 0.5 M H(2)SO(4). The Au@Pt/C catalyst demonstrated enhanced specific activity in methanol electrooxidation and showed multiple CO stripping peaks which were all negatively shifted with respect to a similarly prepared Ag@Pt/C catalyst. The activity enhancement is attributed to the presence of Au underneath a very thin Pt shell where electron exchange between Au and Pt had promoted the formation of active oxygen species on Pt, which facilitated the removal of inhibiting CO-like reaction intermediates.     

水溶液中碳纳米管的表面增强拉曼光谱研究

合成了碳纳米管和金纳米颗粒的复合物, 测量了水溶液相中复合物的表面增强拉曼光谱, 结果表明, 碳纳米管的巯基化修饰可以提高碳纳米管与金纳米颗粒复合的效率, 随着金纳米颗粒负载量的增加, 碳纳米管的拉曼信号逐渐增强. 加入己二胺分子可以减小金纳米颗粒之间的距离使表面增强效应更显著, 碳纳米管的拉曼光谱得到进一步的增强. 还可进一步在复合体系中加入对巯基苯胺和罗丹明B等小分子拉曼探针, 利用金纳米颗粒的表面增强效应, 这种多元复合体系有望作为多通道拉曼成像探针材料.     

Removal of residual metal catalysts with iron/iron oxide nanoparticles from coordinating environments

The application of Fe@FexOy nanoparticles was examined for the sequestration of catalytic metal impurities from organic reaction products. An X-ray photoelectron spectroscopy (XPS) study of the recovered particles confirmed Fe@FexOy sequestered Co2+, Cu2+, Ni2+, RhX+, Pd2+, Ag+, and Pt4+ by coordination of the metal ion to the iron oxide surfaces and followed by subsequent reduction of the surface-bonded ions to their metallic state. Fe@FexOy metal sequestration was found to be effective for catalyst impurities in the absence of strongly coordinating environments but was inhibited by the presence of phosphines. Sequestration of phosphine-coordinated metal impurities was achieved through the addition of either cysteamine or 3-mercaptopropionic acid to the Fe@FexOy during sequestration. This approach was applied to model syntheses using Grubbs' Catalyst (first generation), Pd(PPh3)4, Pd2(dba)3, and Wilkinson's Catalyst (RhCl(PPh3)3).     

Microwave-irradiated synthesized platinum nanoparticles/carbon nanotubes for oxidative determination of trace arsenic(III)

Platinum nanoparticles/carbon nanotubes (Pt_nano/CNTs) were rapidly synthesized by microwave radiation, and applied for the oxidative determination of arsenic(III). The transmission electron microscopy (TEM) revealed the size of synthesized Pt nanoparticles with nominal diameter of 15 ± 3 nm. Pt_nano/CNTs modified glassy carbon electrode (Pt_nano/CNTs/GCE) exhibited better performance for arsenic(III) analysis than that of Pt nanoparticles modified GCE (Pt_nano/GCE) by electrochemical deposition or Pt foil electrode. Excellent reproducibility of the Pt_nano/CNTs/GCE was obtained with the relative standard deviation (RSD) of 3.5% at 20 repeated analysis of 40 μM As(III), while the RSD was 9.8% for Pt_nano/GCE under the same conditions. The limit of determination (LOD) of the Pt_nano/CNTs/GCE was 0.12 ppb, which was 1–2 orders of magnitude lower than that of Pt_nano/GCE or Pt foil electrode.     

Selective heterogeneous nucleation and growth of size-controlled metal nanoparticles on carbon nanotubes in solution

We present a novel approach to the in situ deposition of size-controlled platinum nanoparticles on the exterior walls of carbon nanotubes (CNTs). The reduction of metal ions in ethylene glycol (EG), by the addition of a salt such as sodium dodecyl sulfate (SDS), p-CH3C6H4SO3Na, LiCF3SO3, or LiClO4, results in high dispersions and high loadings of platinum nanoparticles on CNTs without aggregation. We have performed controlled experiments to elucidate the mechanism. By exploiting the salt effect, our method effectively depresses homogeneous nucleation, leading to selective heterogeneous metal nucleation and growth, even on unmodified CNTs. In the 2.3-9.6 nm size range, the size of platinum nanoparticles, at 50% loading, can be controlled by changing the concentration of metal ions, the reaction temperature, the reducing reagent or the means by which reactive solutions are added. Our method provides a flexible route towards the preparation of novel one-dimensional hybrid materials, for which a number of promising applications in a variety of fields can be envisioned.     

Pyrene-assisted synthesis of size-controlled gold nanoparticles in sodium dodecyl sulfate micelles

Gold nanoparticles prepared by chemical reduction in sodium dodecyl sulfate (SDS) solution are size-controlled with the addition of pyrene. Micellar electrokinetic capillary chromatography (MEKC) is applied to the system to examine the size and polydispersity of gold nanoparticles and to show that pyrene has the extraordinary effect in decreasing the size and narrowing the dispersity of gold nanoparticles. The MEKC electropherograms further suggest that pyrene could be oxidized by the aqueous Au(III) complexes first. All the reduced Au complexes were then solubilized in the pyrene-SDS micelles. The growth of gold nanoparticles beyond the embryonic stage was subsequently inhibited by the encapsulating SDS and electrophilic pyrene.     

Pt@Pd(x)Cu(y)/C core-shell electrocatalysts for oxygen reduction reaction in fuel cells

A series of carbon-supported core-shell nanoparticles with Pd(x)Cu(y)-rich cores and Pt-rich shells (Pt@Pd(x)Cu(y)/C) has been synthesized by a polyol reduction of the precursors followed by heat treatment to obtain the Pd(x)Cu(y)/C (1 ≤ x ≤ 3 and 0 ≤ y ≤ 5) cores and the galvanic displacement of Pd(x)Cu(y) with [PtCl(4)](2-) to form the Pt shell. The nanoparticles have also been investigated with respect to the oxygen reduction reaction (ORR) in proton-exchange-membrane fuel cells (PEMFCs). X-ray diffraction (XRD) analysis suggests that the cores are highly alloyed and that the galvanic displacement results in a certain amount of alloying between Pt and the underlying Pd(x)Cu(y) alloy core. Transmission electron microscopy (TEM) images show that the Pt@Pd(x)Cu(y)/C catalysts (where y > 0) have mean particle sizes of <8 nm. Compositional analysis by energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) clearly shows Pt enrichment in the near-surface region of the nanoparticles. Cyclic voltammograms show a positive shift of as much as 40 mV for the onset of Pt-OH formation in the Pt@Pd(x)Cu(y)/C electrocatalysts compared to that in Pt/C. Rotating disk electrode (RDE) measurements of Pt@PdCu(5)/C show an increase in the Pt mass activity by 3.5-fold and noble metal activity by 2.5-fold compared to that of Pt/C. The activity enhancements in RDE and PEMFC measurements are believed to be a result of the delay in the onset of Pt-OH formation.     

Bimetallic Cu–Pt/nanoporous carbon composite as an efficient catalyst for methanol oxidation

A novel bimetallic Cu–Pt nanoparticle supported onto Cu/indirectly carbonized nanoporous carbon composite (Cu–Pt/ICNPCC) was prepared through a two-step process: first, carbonization of furfuryl alcohol-infiltrated MOF-199 [metal–organic framework Cu₃(BTC)₂ (BTC?=?1,3,5-benzene tricarboxylate)], without removing the Cu metal with HF aqueous solution; second, the partial galvanic replacement reaction (GRR) of Cu nanoparticles by Pt^IV upon immersion in a platinum(IV) chloride solution. The synthesized materials characterized by powder X-ray diffraction, Fourier transform infrared spectroscopy, field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy (EDS), and electrochemical methods. The EDS result revealed that part of Cu nanoparticles have been substituted by Pt nanoparticles after GRR. The methanol oxidation at the surface of Cu–Pt/ICNPCC was investigated by cyclic voltammetry method in 0.5 M H₂SO₄ and indicated good electro-catalytic activity towards methanol oxidation (E_p?=?0.85 V vs. NHE and j_f?=?1.00 mA cm^?2). It is suggested that this improvement is attributed to the effect of proper Cu/ICNPCC for fine dispersion, efficient adhesion, and prevention of Pt coalescing.