溶胶-凝胶法制备掺Eu3+的SiO2玻璃的结构及发光性

利用溶胶-凝胶技术制备了掺不同量Eu3+和不同退火温度下的SiO2凝胶和玻璃,通过在不同退火温度下样品的激发光谱、发射光谱、红外光谱和差热-热重曲线,研究了掺Eu3+的SiO2玻璃材料的结构和发光性能。结果显示当Eu3+的掺杂量大于1.86%（质量分数）,Eu3+的发光强度趋于稳定,当样品的退火温度大于300℃时,SiO2凝胶玻璃中吸附的水已基本除净,此时显示出Eu3+的特征发射光谱,谱带位置分别是614,596,588,577nm,分别归属于5D0-7F2,5D0-7F1,5D0-7F0跃迁,对应的激发光谱显示6个峰,位置分别是318,362,380,393,412,462nm,说明300～500℃是凝胶向玻璃转变的关键温度,而水对Eu3+的发光有强烈的淬灭作用。     

掺Tb-硅基发光材料制备过程中结构及发光性能

采用溶胶 凝胶技术,制备了不同退火温度下掺Tb3＋的SiO2玻璃,掺Tb3＋的凝胶玻璃在448,544,585,620 nm显示Tb3＋的5D4 7FJ(J=3,4,5,6)的特征发光光谱.通过不同退火温度下样品的激发光谱、发射光谱、红外光谱、远红外光谱及差热 热重谱研究了掺Tb3＋的硅基材料由凝胶向玻璃转变过程中的结构变化及对Tb3＋发光性能的影响.结果显示,在50～100 ℃退火温度下,凝胶大部分吸附水分子被除去,在150～500 ℃退火温度区,是凝胶向玻璃转变的主要结构变化区,并且其发光强度也明显增加,到800 ℃时趋于稳定.这些现象得出一个结论,Tb3＋的发光跃迁被O－H基强烈猝灭而随退火温度的升高而加强.     

掺Tb-硅基发光材料制备过程中结构及发光性能

采用溶胶-凝胶技术 ,制备了不同退火温度下掺 Tb3＋的 SiO2玻璃 ,掺 Tb3＋的凝胶玻璃在 448,544,585,620 nm显示 Tb3＋的 5D4- 7FJ(J=3,4,5,6)的特征发光光谱 .通过不同退火温度下样品的激发光谱、发射光谱、红外光谱、远红外光谱及差热-热重谱研究了掺 Tb3＋的硅基材料由凝胶向玻璃转变过程中的结构变化及对 Tb3＋发光性能的影响 .结果显示 ,在 50～ 100℃退火温度下 ,凝胶大部分吸附水分子被除去 ,在 150～ 500℃退火温度区 ,是凝胶向玻璃转变的主要结构变化区 ,并且其发光强度也明显增加 ,到 800℃时趋于稳定 .这些现象得出一个结论 ,Tb3＋的发光跃迁被 O－ H基强烈猝灭而随退火温度的升高而加强 .     

掺Eu的SiO2-B2O3体系和SiO2-B2O3-Na2O体系的结构及Eu3+的发光性质

采用溶胶-凝胶技术制备了掺Eu3+的以SiO2-B2O3和SiO2-B2O3-Na2O为基质的玻璃态发光材料. 通过激发光谱、发射光谱研究了Eu3+的发光性质, 通过红外光谱、 TEM 、 XRT进一步研究了基质结构变化对发光性能的影响. 结果显示 材料经 600 ℃退火处理后, 结构已十分稳定. 在588 nm和613 nm处显示弱的Eu3+的特征发射光谱, 对应于Eu3+的5D0-7Fj(j=1,2)跃迁. 以SiO2-B2O3为基质的玻璃材料的红外光谱显示形成了Si-O-B键. 该结构对Eu3+的发光有严重的淬灭作用, 使Eu3+的发光强度大大减弱. 以SiO2-B2O3-Na2O为基质的玻璃材料显示Eu3+的发光增强, 红外光谱显示不存在Si-O-B键的振动吸收. 可能是Na取代B的位置, 形成了Si-O-Na键. 此结构对Eu3+的发光有一定增加作用.     

硼离子对铕掺杂SiO2干凝胶发光性能的影响

采用溶胶-凝胶法制备了Al单掺和B，Al共掺的Eu掺杂SiO2干凝胶。利用荧光光谱、IR，XRD，DSC，TG／DTG等技术研究了硼离子、退火温度对样品发光性质的影响。经500℃以上退火处理用248nm激发的样品，产生Eu^3＋离子^5D0→^7FJ的特征发射，^5D0→^7F1的跃迁分裂为两个峰。比较615nm处的发光强度，掺硼酸样品的发光强度是不加硼酸发光强度的3．3倍。这是因为B离子的加入，在材料中形成了Si—O—B键，破坏了网络的对称性，加强了Eu^3＋的红光发射。当退火温度上升到850℃用350nm激发时，样品有很强的Eu^2＋蓝光发射。Al单掺的发射中心在437nm处，发射半峰宽约为70nm，而B，Al共掺样品的发光中心蓝移到425nm处，单掺样品的蓝光强度几乎是共掺样品强度的2倍。这是由于硼酸的加入改变了基质的网络结构，从而导致单掺和共掺样品发射峰位和强度的改变。     

溶胶-凝胶法制备掺Sm3+的SiO2玻璃的结构及发光性能

利用溶胶-凝胶技术制备了掺不同量Sm3+和不同退火温度下的SiO2凝胶和玻璃,通过三维荧光光谱、激发光谱、发射光谱的测试,确定了Sm3+在SiO2凝胶玻璃中的最佳激发波长为360 nm,最强发射波长为610 nm,激发光谱的峰位置在360、393、464 nm处,发射光谱的峰位置在578、591、595、610、732nm处,分别归属于4G5/2-6H5/2、4G5/2-6H7/2、4G5/2-6H11/2跃迁,并证明当掺杂量达到1.15%时,Sm3+的发光最强,当Sm3+的掺杂量超过1.15%时,发生浓度猝灭效应.     

Ca2Y8（SiO4）6O2：RE（RE=Eu,Tb）发光薄膜的制备及发光性能的研究

采用溶胶－凝胶法制备了稀土离子掺杂（Eu^3 ,Tb^3 )的氧磷灰石三元稀土硅酸盐Ca2Y8(SiO4)6O2发光薄膜。通过X射线衍射（XRD）,红外光谱（IR）,扫描电镜（SEM）等方法对薄膜的组成、结构、颗粒尺寸、形貌及厚度进行了研究,通过发光光谱对薄膜的发光性质进行了分析。XRD结果表明700℃时薄膜尚处于非晶态,800℃时已开始有Ca2Y8(SiO4)6O2的物相形成,1000℃时结晶已完全。这一点和红外光谱的结果相符。发光光谱测试表明Ca2Y8(SiO4)6O2:Eu^3 薄膜显示了很强的红光发射,并以Eu^3＋的^5D0-^7F2(616nm)超灵敏跃迁为最强一组。Ca2Y8(SiO4)6O2:Tb^3 的发射光谱由蓝光发射和绿光发射两部分组成,前者对应于^5D3-^7FJ,后者对应于^5D4-^7FJ(J=6,5,4,3),且以^5D4-^7F5(544nm)绿光发射为最强。     

Eu:GGG纳米荧光粉体制备及其光学特性

采用液相共沉淀方法并在不同烧结温度下制得了Eu：GGG荧光粉体。用X射线衍射分析了样品的结构，计算了其晶格常数，为1．2371nm。室温下，测量了Eu：GGG的光致发射光谱、激发光谱和荧光衰减曲线。激发光谱在波长240～287nm的谱带内和393。。处有强的激发，分别来自于Eu^3＋O2^-间的电荷迁移态吸收和Eu“的^7F0→^5L6的跃迁吸收，同时在274nm处也出现了Gd^3＋的^8S7/2→^6I1的特征吸收。393nm激发下，591nm处的发射峰最强，对应Eu^3＋的^5D0→^7F1的磁偶极跃迁，可能由于部分Eu^3＋处于反演中心对称格位所致。随着烧结温度升高，Eu：GGG的发光强度增强，这可能由于随着烧结温度升高，样品晶粒尺寸变大，单位体积内被激发的Eu^3＋离子数增加引起，而591nm发光的荧光寿命变短，可能是由Eu^3＋离子的能量共振传递过程中发光被陷阱捕获所致。     

Eu3+掺杂SiO2-Al2O3-B2O3玻璃制备及光谱性能研究

高温溶制了Eu^3＋掺杂SiO2-Al2O3-B2O3-MxOy（M=Li^＋,Na^＋,K^＋,Mg^2＋,Ca^2＋,Sr^2＋,RE^3＋）硼硅酸盐玻璃,测试了玻璃样品的发射光谱、激发光谱和透射光谱,研究了不同碱金属离子、碱土金属离子对该系统荧光性能的影响。利用发射光谱计算了Ω2,Ω4以及^5D0到^7F2,^7F4的自发辐射几率和振子强度f（^5D0→^7F2）,f（^5D0→^7F4）。结果表明,材料的发射能级为^5D0→^7F1（590nm）,^5D0→^7F2（617nm）,^5D0→^7F4（698nm）,而且材料的结构对称性越差,跃迁戒律打破地越彻底,荧光发射越强。     

Tb掺杂SiO2-B2O3-NaF玻璃的制备及发光性质

使用正硅酸乙酯、硼酸和氟化钠为前驱体,0.10 mol•L-1TbCl3溶液为掺杂剂,通过溶胶-凝胶方法制备了Tb3＋掺杂的SiO2-B2O3-NaF玻璃,研究了Tb3＋在SiO2-B2O3-NaF体系中的发光性质,结果显示发光体能产生强的绿色发光(544 nm),归属于Tb3＋的5D4—7F5电子跃迁.Tb3＋含量不同时,除发光强度不同外,其发射光谱基本相同,并且在低掺杂Tb3＋样品和低退火温度样品中检测到了来自5D3跃迁产生的峰,其跃迁随Tb3＋掺杂浓度的增加和退火温度的升高而发生猝灭,这种现象归因于5D3－5D47F6—7F0和/或5D3—7F07F6—5D4跃迁中发生了交叉弛豫现象.Tb3＋在SiO2-B2O3-NaF玻璃中的激发光谱由一个宽峰和一系列窄峰组成,宽峰最大波长位于230 nm,对应于Tb3＋的4f 8—4f 75d 1跃迁,一系列窄峰位于300～380 nm处,归属于4f 8跃迁,所有发光材料的XRD和TEM测试显示材料是非晶态的.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.