铁电单晶0.62Pb(Mg1/3Nb2/3)O3-0.38PbTiO3折射率的研究

用最小偏向角法在20℃下精确测量了0.62Pb(Mg_1/3Nb_2/3)O_{3< /sub>-0.38PbTiO3( 0.62PMN-0.38PT)单晶的折射率，给出了该温度下折射率色散的Sellmeier方程.研究了能带 结构与折射率的关系，计算了样品的Sellmeier光学系数：对no，E0=5.50eV,λ0=0.2 26μm，Ｓ０=1.004×10¹⁴m^-2，Ed=28.1 0eV；对ne，Ｅ0=5.57eV,λ 0=0.223μm，S0=1.017×10¹⁴m^-2，Ed=28.10eV.A BO3型钙钛矿材料中，BO6八面体基元决定了晶体的能带结构，对折 射率产生重要影响. 关键词： PMNT单晶 折射率 Sellmeier光学系数}     

铁电单晶Pb(Mg1/3Nb2/3)O3-PbTiO3的高场致应变及其在层叠式驱动器中的应用

通过研究(1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMNT)单晶在不同方向、不同组分下高场致应变的特性,确定了〈001〉取向PMNT单晶(29%≤x≤31%)为制作层叠式驱动器的最佳组分范围,这组分的单晶具有高场致应变、低滞后而且性能较稳定的特点.研究结果表明,在保证应变曲线的线性和低滞后的前提下,将近-2kV/cm的负电场能够运用于〈001〉方向的PMNT晶体上. 40层(每片晶片尺寸为7mm×7mm×0.7mm)PMNT层叠式驱动器在电场 -1.5-10kV/cm的驱动下,可以获得38.1μm的纵向位移,负载40N的重量后,位移量减为34μm.     

弛豫铁电单晶0.93Pb(Zn1/3Nb2/3)O3-0.07PbTiO3的电光性能研究

以波长为632.8 nm的He-Ne激光作为光源,研究了三方相弛豫铁电单晶0.93Pb(Zn1/3Nb2/3)O3-0.07PbTiO3在室温下的折射率和线性电光性质.通过测量晶体的布儒斯特角,确定了单晶的两个主轴折射率:no=2.466,ne=2.488.利用改进的马赫-泽德尔干涉法测量了单晶的线性电光系数:r33=71 pm/V,r13=4 pm/V.计算得到有效电光系数rc=67 pm/V及半波电压Vπ=610 V.单晶优异的电光性能使其在激光调制与偏转领域有着巨大的应用潜力.     

0.7Pb(Mg1/3 Nb2/3)O3-0.3PbTiO3单晶/环氧树脂1-3型复合材料的压电性能研究

模拟了0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3(PMN-0.3PT)单晶1-3型压电复合材料的性能与单品体积分数的关系,得出性能最优时压电相的体积分数为64%,在这一体积分数下,采用切割-填充法,并使用了不同类型的环氧树脂填充制备复合材料.系统地研究了聚合物相对复合材料性能的影响,研究表明,减小聚合物相的刚度系数c和密度ρ有利于提高复合材料的性能,且聚合物相与压电相的结合强度对性能的影响非常明显,制备的PMN-0.3 PT单晶1-3型复合材料的厚度伸缩机电耦合系数k1高达90.1%,压电系数d33大于1000 pC/N,机械品质因数Qm为10.39,声阻抗Z也大大降低,性能明显优于传统的Pb(Zrx,Ti1-x)O3(PZT)陶瓷及其1-3复合材料,在压电换能器和传感器中显示出广阔的前景.     

化学溶液法制备的Pb(Mg1/3 Nb2/3)O3-PbTiO3薄膜的光学性能

用化学溶液方法在宝石衬底及有LaNiO3缓冲层的Pt/TiO2/SiO2/Si衬底上制备了92%Pb(Mg1/3 Nb2/3)O3-8%PbTiO3(PMNT)薄膜,X射线衍射测试结果表明:在有LaNiO3缓冲层的Pt/TiO2/SiO2/Si衬底上制备的PMNT薄膜几乎是纯钙钛矿相,且薄膜呈现(110)择优取向.通过对Pt/TiO2/SiO2/Si衬底上的PMNT薄膜在2.5-12.6μm波长范围内的红外椭圆偏振光谱测试,并拟合得到了PMNT薄膜在2.5-12.6μm波长范围内的光学常数(n和k),通过对宝石衬底上的PMNT薄膜在200-1100nm波长范围内的可见-紫外透过率测试,并拟合得到了PMNT薄膜在200-1100nm波段的光学常数(n和k)和吸收系数α,进而推导出PMNT薄膜的禁带宽度为4.03eV.     

铁电单晶Pb (Mg1/3Nb2/3)O3-PbTiO3的高场致应变及其在层叠式驱动器中的应用

通过研究(1_x)Pb(Mg_1/3Nb_2/3)O_{3_x}PbTiO3(PMNT)单晶在不同方向、不同组分下高场致应变的特性，确定了〈001〉取向 PMNT单晶（29％≤x≤31%）为制作层叠式驱动器的最佳组分范围，这组分的单晶具有高场致应变、低滞后而且性能较稳定的特点.研究结果表明，在保证应变曲线的线性和低滞后的前提下，将近-2kV/cm的负电场能够运用于〈001〉方向的PMNT晶体上. 40层（每片晶片尺寸为7mm×7mm×0.7mm）PM 关键词： PMNT单晶 场致应变 PMNT驱动器     

弛豫型铁电单晶0.67Pb(Mg_(1/3)Nb_(2/3))O_3-0.33PbTiO_3的拉曼散射研究

本文采用拉曼散射技术在温度从374到-196℃的范围内,研究了弛豫型铁电单晶0.67Pb(Mg1/3Nb2/3)O3-0.33PbTiO3(PMNT)。观察了在不同温度下拉曼光谱的变化,经分析这些变化反映了该晶体经历了两个相变:第一个相变温度发生在120℃,从顺电立方相到铁电四方相的相变,780 cm-1处模式在VH偏振下的改变标志了这一相变;第二个相变温度发生在34℃,是从铁电四方相到铁电三方相的相变,软模的出现代表了这一相变。     

Synthesis and electrical properties of Pb(Mg1/3Nb2/3)O3–PbTiO3 ceramics

Ceramic compositions of a combination between lead magnesium niobate, Pb(Mg_1/3Nb_2/3)O₃, and lead titanate, PbTiO₃, were fabricated by using Mg₄Nb₂O₉ precursor technique. Their electrical properties with respect to temperature and frequency were examined and the effect of sintering conditions on phase formation, densification, microstructure and electrical properties of the ceramics were examined. It has been found that optimisation of sintering condition can lead to a highly dense and pyrochlore-free PMN–PT ceramics. The gradual decreasing of the physical properties of the sintered ceramics was related to the gradual decrease of density and inhomogeneous microstructure. The results also revealed that for the lower concentration of lead titanate a relaxor behavior is noticed with a high electrostrictive effect, which was almost hysteretic free. However, higher amount of lead titanate led to a normal ferroelectric behavior.     

化学溶液法制备的Pb(Mg1/3Nb2/3)O3-PbTiO3薄膜的光学性能

用化学溶液方法在宝石衬底及有LaNiO₃缓冲层的Pt/TiO₂/SiO₂/Si衬底上制备了92%Pb(Mg_1/3Nb_2/3)O₃-8%PbTiO₃(PMNT)薄膜，X射线衍射测试结果表明：在有LaNiO₃缓冲层的Pt/TiO₂/SiO₂/Si衬底上制备的PMNT薄膜几乎是纯钙钛矿相，且薄膜 关键词： PMNT薄膜 光学性能 化学溶液法     

Field-induced piezoelectric response in Pb(Mg1/3Nb2/3)O3–PbTiO3 single crystals

The electric field induced strain, piezoelectric and electromechanical response in relaxor based single crystal piezoelectrics (1−x)Pb(Mg_1/3Nb_2/3)O₃–xPbTiO₃(PMNT100x) were investigated as a function of dc bias and temperature along the crystallographic [001] orientation. With increasing temperature and dc bias, monoclinic and rhombohedral phases were found to coexist in the crystals, exhibiting large strain hysteresis, while above a threshold temperature and dc bias, the induced monoclinic and tetragonal phases were found to show very low strain hysteresis. The electric field level for the monoclinic to tetragonal phase transformation was found to exponentially decay with temperature. The mechanical quality factor Q for the tetragonal phase exhibits higher values when compared to rhombohedral and monoclinic phases, displaying improved domain stability. The domain stability of tetragonal crystals as a function of sample thickness was also studied, it was found that a higher dc bias was needed for thinner tetragonal crystals in order to stabilize the single domain configuration and reduce the strain hysteresis.     

Energy harvesting using multilayer structure based on 0.71Pb(Mg1/3Nb2/3)O3–0.29PbTiO3 single crystal

In this paper we fabricated the multilayer structure used as the resonance-based vibration energy-harvesting device based on 0.71Pb(Mg_1/3Nb_2/3)O₃–0.29PbTiO₃ single crystal. The performances of the device including the output voltage and power were studied systematically. Under a cyclic force of 4 N (peak value), a high output power of 4.94 mW and a corresponding peak voltage of 3.14 V were measured at 1.4 kHz with a matching load resistance of 1.0 kΩ. The results demonstrate the potential of the device in energy-harvesting applied to low-power portable electronics and wireless sensors.     

Photorefractive effect in the relaxor ferroelectric material 0.91Pb(Zn1/3Nb2/3)O3-0.09PbTiO3

The photorefractive effect in a nominally undoped 0.91Pb(Zn1/3Nb2/3)O3-0.09PbTiO3 single crystal is measured. We report what is, to our knowledge, the first observation of the photorefractive effect in Pb-based relaxor ferroelectric crystals. The crystal is grown by the flux solution method. Then it is cut into a 2 mm x 4 mm x 8 mm piece and electrically poled along the [111] direction. The coupling constant of the two-wave mixing is 17 cm(-1), and the normalized time constant under 1-W/cm(2) illumination is 12 s at a wave-length of 476 nm. The effective trap density is calculated as 5 x 10(16) cm(-3) from the Debye screening length under the assumption of Kukhtarev's band-transport model. The dominant carrier is identified to be holes from the direction of two-wave mixing energy transfer.     

等静压下0.75Pb（Mg1/3Nb2/3）O3-0.25PbTiO3陶瓷的介电性能研究

研究了等静压对0.75Pb（Mg_1/3Nb_2/3）O₃-0.25PbTiO₃（PMN-25PT）陶瓷介电温谱的影响,PMN-25PT剩余极化随等静压变化和等静压压致相变.结果表明,随着压力增加,PMN-25PT的介电峰值温度T_m降低,/+{dT_m}/-{dP}≈-4℃/kbar,极化弛豫增强;剩余极化随压力增加连续减小;介电常数对压力的依赖关系与对温度场的依赖相似,压力诱导PMN-25PT发生弛豫铁电—顺电相变,相变为宽化的渐变过程,频率色散和极化弛豫更加强烈和普遍. 关键词： 铌镁酸铅-钛酸铅 等静压 介电弛豫 压致相变     

Effect of bias field on the dielectric properties of 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 single crystals with different orientations

Microdomain-macrodomain transformations and phase transitions in 0.7Pb(Mg_1/3Nb_2/3)O₃-0.3PbTiO₃ single crystals were investigated by studying their relative permittivity under various dc bias at constant heating and cooling rates. The orientation dependence of the bias field effect was revealed by examining the temperature dependence of relative permittivity as a function of crystal orientation (the 111, 011 and 001 directions) and dc bias field. The crystals have a microdomain rhombohedral ferroelectric state in the ferroelectric phase under zero dc bias. External bias field could modulate the domain state and induce a macrodomain state in the crystals. Also, it is proposed that the dc bias applied along the 001 or 011 direction could induce a tetragonal ferroelectric phase or an orthorhombic ferroelectric phase, respectively, in an intermediate temperature range. PACS 77.80.-e; 77.22.-d; 81.40.-z     

Solid-state single and triple-quantum 93Nb MAS NMR studies of ferroelectric Pb(Mg1/3Nb2/3)O3 and a related pyrochlore

Pb(Mg1/3Nb2/3)O3 (PMN), a well-known relaxor ferroelectric material, and a related pyrochlore phase have been studied by single- and triple-quantum 93Nb MAS NMR spectroscopy. The assignment of the NMR resonances has been attempted.     

Specific-heat anomaly caused by ferroelectric nanoregions in Pb(Mg(1/3)Nb(2/3))O3 and Pb(Mg(1/3)Ta(2/3))O3 relaxors

The specific heat of typical relaxors, Pb(Mg(1/3)Nb(2/3))O3 (PMN) and Pb(Mg(1/3)Ta(2/3))O3 (PMT), was measured by adiabatic and relaxation methods between 2 and 420 K. A broad anomaly was found in the specific heat curve over the wide temperature range between 150 and 500 K for PMN, and between 50 and 400 K for PMT, which provides evidence for the formation of ferroelectric nanoregions (FNR) in the paraelectric matrix. The entropy of the anomaly was estimated as 3.3 J K(-1) mol(-1) and 2.9 J K(-1) mol(-1) for PMN and PMT, respectively, which implies an order-disorder-type mechanism for the formation of FNR.