Colorimetric assay for parallel detection of Cd2+, Ni2+ and Co2+ using peptide-modified gold nanoparticles

A colorimetric assay has been developed for parallel detection of Cd(2+), Ni(2+) and Co(2+) utilizing peptide-modified gold nanoparticles (P-AuNPs) as a sensing element based on its unique surface plasmon resonance properties. The functional peptide ligand, CALNNDHHHHHH, was self-assembled on gold nanoparticles (AuNPs) to produce P-AuNPs probe. The P-AuNPs probe could be used to simultaneously detect and showed different responses to the three ions Cd(2+), Ni(2+) and Co(2+) in an aqueous solution based on the aggregation-induced color change of AuNPs. The method showed good selectivity for Cd(2+), Ni(2+) and Co(2+) over other metal ions, and detection limit as low as 0.05 μM Cd(2+), 0.3 μM Ni(2+) or 2 μM Co(2+). To simultaneously (or parallel) detect the three metal ions coexisting in a sample, EDTA and imidazole were applied to mask Co(2+) and Ni(2+) for detecting Cd(2+), glutathione and EDTA were applied to mask Cd(2+) and Co(2+) for detecting Ni(2+), and glutathione and imidazole were applied to mask Cd(2+) and Ni(2+) for detecting Co(2+). Finally, the simple and cost-effective probe could be successfully applied for simultaneously detecting Cd(2+), Ni(2+), and Co(2+) in river water. Because this novel P-AgNPs-based probe design offers many advantages, including simplicity of preparation and manipulation compared with other methods that employ specific strategies, the sensing system shows potential application in the developing region for monitoring water quality.     

Incorporation of triazole into a quinoline-rhodamine conjugate imparts iron(iii) selective complexation permitting detection at nanomolar levels

Two new rhodamine based probes 1 and 2 for the detection of Fe(3+) were synthesized and their selectivity towards Fe(3+) ions in the presence of other competitive metal ions tested. The probe 1 formed a coloured complex with Fe(3+) as well as Cu(2+) ions and revealed the lack of adequate number of coordination sites for selective complexation with Fe(3+). Incorporation of a triazole unit to the chelating moiety of 1 resulted in the probe 2, that displayed Fe(3+) selective complex formation even in the presence of other competitive metal ions like Li(+), Na(+), K(+), Cu(2+), Mg(2+), Ca(2+), Sr(2+), Cr(3+), Mn(2+), Fe(2+), Co(2+), Ni(2+), Zn(2+), Cd(2+), Hg(2+) and Pb(2+). The observed limit of detection of Fe(3+) ions (5 × 10(-8) M) confirmed the very high sensitivity of 2. The excellent stability of 2 in physiological pH conditions, non-interference of amino acids, blood serum and bovine serum albumin (BSA) in the detection process, and the remarkable selectivity for Fe(3+) ions permitted the use of 2 in the imaging of live fibroblast cells treated with Fe(3+) ions.     

A simple but highly sensitive and selective colorimetric and fluorescent probe for Cu2+ in aqueous media

In this paper, CN-DPA was prepared as an effective colorimetric and fluorescent probe for copper ions (Cu(2+)) in aqueous solution. It exhibits good sensitivity and selectivity for Cu(2+) over other metal ions both in aqueous solution and on a simple colorimetric paper-made test kit. Upon addition of Cu(2+), a remarkable color change from purple to colorless was easily observed by the naked eye, and a fluorescence quenching was also determined. Furthermore, CN-DPA can be used to quantitatively detect Cu(2+). The linear range was 0-5 μM determined by absorption spectrometry. All these selective and sensitive results indicate that CN-DPA could meet the selective requirements for biomedical and environmental application and be sensitive enough to detect Cu(2+) in environmental water samples, even in drinking water, which has a limit of 20 μM defined by the U.S. Environmental Protection Agency.     

Colorimetric assay for mercury (II) based on mercury-specific deoxyribonucleic acid-functionalized gold nanoparticles

A colorimetric nanoprobe-mercury-specific DNA-functionalized gold nanoparticles (Au-MSD) was developed for sensing Hg(2+). The new mercury-sensing concept relies on measuring changes in the inhibition of "non-crosslinking" aggregation of Au-MSD-induced by the folding of mercury-specific DNA strand through the thymine-Hg(2+)-thymine (T-Hg(2+)-T) coordination. In the absence of Hg(2+), a high concentration of MgCl(2) (50 mM) results in a rapid aggregation of Au-MSD because of the removal of charge repulsion. When Hg(2+) is present, the particles remain stable due to the folding of MSD functionalized on the particle surface. The assay enables the colorimetric detection of Hg(2+) in the concentration range of 0.1-10 μM Hg(2+) ions with a detection limit of 60 nM, and allows for the selective discrimination of Hg(2+) ions from the other competitive metal ions. Toward the goal for practical applications, the sensor was further evaluated by monitoring Hg(2+) in fish tissue samples.     

Coordination of mercury(II) to gold nanoparticle associated nitrotriazole towards sensitive colorimetric detection of mercuric ion with a tunable dynamic range

A simple colorimetric assay with high sensitivity, excellent selectivity and a tunable dynamic range is reported for detecting trace amounts of mercuric ion in aqueous solution based on the coordination of Hg(2+) to the gold nanoparticle (AuNP)-associated 3-nitro-1H-1,2,4-triazole (NTA). The NTA can stabilize the AuNPs against tris-induced aggregation through capping the AuNPs. In the presence of Hg(2+), the NTA is released from the AuNP surface via the formation of a NTA-Hg(2+) coordination complex, leading to the aggregation of AuNPs in tris. This detection strategy is unique in terms of high sensitivity and excellent selectivity, a tunable dynamic range, and simplicity of probe preparation. Low detection limits of 7 nM (1.4 ppb) and 50 nM (10 ppb) can be achieved by spectrophotometer and by direct visualization, respectively, under the optimized conditions. No noticeable colour changes are observed towards other metal ions (Ag(+), Zn(2+), Ni(2+), Cr(3+), Mg(2+), Cu(2+), Co(2+), Cd(2+), Pb(2+), Fe(2+)) at concentrations up to 100 μM without the need of any other masking agents. In addition, the dynamic range of the assay can be easily tuned by adjusting the amount of NTA in the NTA-AuNP probes. More importantly, the NTA-AuNP probes can be simply prepared by mixing NTA with as-synthesized citrate-capped AuNPs. This not only avoids complicated surface modifications and tedious separation processes, but also is cost-effective.     

Visual detection of copper(II) ions in blood samples by controlling the leaching of protein-capped gold nanoparticles

We have developed a simple, low-cost, paper-based probe for the selective colorimetric detection of copper ions (Cu(2+)) in aqueous solutions. The bovine serum albumin (BSA)-modified 13.3-nm Au nanoparticle (BSA-Au NP) probe was designed to detect Cu(2+) ions using lead ions (Pb(2+)) and 2-mercaptoethanol (2-ME) as leaching agents in a glycine-NaOH (pH 12.0) solution. In addition, a nitrocellulose membrane (NCM) was used to trap the BSA-Au NPs, leading to the preparation of a nanocomposite film consisting of a BSA-Au NP-decorated membrane (BSA-Au NPs/NCM). The BSA-Au NPs probe operates on the principle that Cu deposition on the surface of the BSA-Au NPs inhibits their leaching ability, which is accelerated by Pb(2+) ions in the presence of 2-ME. Under optimal solution conditions (5 mM glycine-NaOH (pH 12.0), Pb(2+) (50 μM), and 2-ME (1.0 M)), the Pb(2+)/2-ME-BSA-Au NPs/NCM enabled the detection of Cu(2+) at nanomolar concentrations in aqueous solutions by the naked eye with high selectivity (at least 100-fold over other metal ions). In addition, this cost-effective probe allowed for the rapid and simple determination of Cu(2+) ions in not only natural water samples but also in a complex biological sample (in this case, blood sample).     

Terbium hybrid particles with spherical shape as luminescent probe for detection of Cu2+ and Fe3+ in water

A novel green emissive terbium inorganic-polymeric hybrid particle was designed and this material could detect cations in water. Polyvinyl alcohol as an amphiphilic surfactant rendered the powders dispersible in water with regular round shape (10-20 μm). Interestingly, we noticed that not only Cu(2+) (detection limit 10(-4)M) but also Fe(3+) (detection limit 10(-4) M) can give rise to emission quenching to this target material in comparison with K(+), Na(+), Fe(2+), Mn(2+), Pd(2+), Cd(2+) and Co(2+) (10(-3) mol L(-1)). We regarded that the coordination interactions between ligand and metal ions resulted in these quenching processes. Additionally, it was found that the sensing material can be repeatedly used at least 5 cycles. More importantly, this novel material demonstrated higher thermal-stability in aqueous media than pure silica hybrid material.     

Solvent controlled sugar-rhodamine fluorescence sensor for Cu(2+) detection

A "turn-on" fluorescence probe for Cu(2+) detection has been reported according to a Cu(2+) triggered spirolactam ring-opening reaction. The probe is a double-responsive fluorescent and colorimetric Cu(2+)-specific sensor in aqueous solution containing 20% of acetonitrile with high selectivity and excellent sensitivity (limit of detection is 12 μg L(-1)). Furthermore, the significant color changes visible to the naked eye at the concentration of 3 μM (ca. 0.20 mg L(-1)) are about ten times lower than the WHO (World Health Organization) recommended level (2.0 mg L(-1)) for Cu(2+) ions in drinking water.     

Highly sensitive and fast responsive fluorescence turn-on chemodosimeter for Cu2+ and its application in live cell imaging

A rhodamine B derivative 4 containing a highly electron-rich S atom has been synthesized as a fluorescence turn-on chemodosimeter for Cu(2+). Following Cu(2+)-promoted ring-opening, redox and hydrolysis reactions, comparable amplifications of absorption and fluorescence signals were observed upon addition of Cu(2+); this suggests that chemodosimeter 4 effectively avoided the fluorescence quenching caused by the paramagnetic nature of Cu(2+). Importantly, 4 can selectively recognize Cu(2+) in aqueous media in the presence of other trace metal ions in organisms (such as Fe(3+), Fe(2+), Cu(+), Zn(2+), Cr(3+), Mn(2+), Co(2+), and Ni(2+)), abundant cellular cations (such as Na(+), K(+), Mg(2+), and Ca(2+)), and the prevalent toxic metal ions in the environment (such as Pb(2+) and Cd(2+)) with high sensitivity (detection limit < or =10 ppb) and a rapid response time (< or =1 min). Moreover, by virtue of the chemodosimeter as fluorescent probe for Cu(2+), confocal and two-photon microscopy experiments revealed a significant increase of intracellular Cu(2+) concentration and the subcellular distribution of Cu(2+), which was internalized into the living HeLa cells upon incubation in growth medium supplemented with 50 muM CuCl(2) for 20 h.     

Exploring the emissive properties of new azacrown compounds bearing aryl, furyl, or thienyl moieties: a special case of chelation enhancement of fluorescence upon interaction with Ca(2+), Cu(2+), or Ni(2+)

Three new compounds bearing furyl, aryl, or thienyl moieties linked to an imidazo-crown ether system (1, 2, and 3) were synthesized and fully characterized by elemental analysis, infrared, UV-vis absorption, and emission spectroscopy, X-ray crystal diffraction, and MALDI-TOF-MS spectrometry. The interaction toward metal ions (Ca(2+), Cu(2+), Ni(2+), and Hg(2+)) and F(-) has been explored in solution by absorption and fluorescence spectroscopy. Mononuclear and binuclear metal complexes using Cu(2+) or Hg(2+) as metal centers have been synthesized and characterized. Compounds 2 and 3 show a noticeable enhancement of the fluorescence intensity in the presence of Ca(2+) and Cu(2+) ions. Moreover compound 3 presents a dual sensory detection way by modification of the fluorimetric and colorimetric properties in the presence of Cu(2+) or Hg(2+). EPR studies in frozen solution and in microcrystalline state of the dinuclear Cu(II)3 complex revealed the presence of an unique Cu(2+) type.     

Dansyl-anthracene dyads for ratiometric fluorescence recognition of Cu2+

Dansyl-anthracene dyads 1 and 2 in CH(3)CN-H(2)O (7:3) selectively recognize Cu(2+) ions amongst alkali, alkaline earth and other heavy metal ions using both absorbance and fluorescence spectroscopy. In absorbance, the addition of Cu(2+) to the solution of dyads 1 or 2 results in appearance of broad absorption band from 200 nm to 725 nm for dyad 1 and from 200 nm to 520 nm for dyad 2. This is associated with color change from colorless to blue (for 1) and fluorescent green (for 2). This bathochromic shift of the spectrum could be assigned to internal charge transfer from sulfonamide nitrogen to anthracene moiety. In fluorescence, under similar conditions dyads 1 and 2 on addition of Cu(2+) selectively quench fluorescence due to dansyl moiety between 520-570 nm (for 1)/555-650 nm (for 2) with simultaneous fluorescence enhancement at 470 nm and 505 nm for dyads 1 and 2, respectively. Hence these dyads provide opportunity for ratiometric analysis of 1-50 μM Cu(2+). The other metal ions viz. Fe(3+), Co(2+), Ni(2+), Cd(2+), Zn(2+), Hg(2+), Ag(+), Pb(2+), Li(+), Na(+), K(+), Mg(2+), Ca(2+), Ba(2+) do not interfere in the estimation of Cu(2+) except Cr(3+) in case of dyad 1. The coordination of dimethylamino group of dansyl unit with Cu(2+) causes quenching of fluorescence due to dansyl moiety between 520-600 nm and also restricts the photoinduced electron transfer from dimethylamino to anthracene moiety to release fluorescence between 450-510 nm. This simultaneous quenching and release of fluorescence respectively due to dansyl and anthracene moieties emulates into Cu(2+) induced ratiometric change.     

Progress on sensors based on nanomaterials for rapid detection of heavy metal ions

The heavy metal ions,especially Cd~(2+),Pb~(2+) and Hg~(2+),show extremely hazard to the environment and human being.The measurement of heavy metal ions using sensors is catching more and more attention for its advantages of high sensitivity and selectivity,low-cost,convenience to handle and rapid detection.In recent years,nanomaterials such as gold nanoparticles(NPs),magnetic nanoparticles,graphene and nanocomposite materials are applied in sensors for improving sensitivity and selectivity,making the research on electrochemical(EC) sensors,spectrometric biosensors and colorimetric biosensors become a hot spot in the application to investigate heavy metal ions,in particular,Cd~(2+),Pb~(2+) and Hg~(2+).In this short review,the research of advanced detection of Cd~(2+),Pb~(2+) and Hg~(2+) and its progress based on nanomaterial sensors in recent years is reviewed.     

Ultrasensitive CE for heavy metal ions using the variations in the chemical structures formed from new octadentate fluorescent probes and cationic polymers

Novel fluorescent probes have been developed for the ultratrace detection of heavy metal ions by capillary electrophoresis using laser-induced fluorescence detection. Based on a molecular design, the probes are composed of an octadentate chelating moiety, a macrocyclic DOTA (tetraazacyclododecanetetraacetic acid) and an acyclic DTPA (diethylenetriaminepentaacetic acid) frame, a spacer and a fluorophore (fluorescein). These were chosen on the basis of their ability to form kinetically inert and highly emissive complexes, and to prevent a quenching effect even with heavy and paramagnetic metal ions. Addition of a cationic polymer, polybrene, in the separation buffer provided high resolution and simultaneous detection of Ca(2+), Mg(2+), Cu(2+), Zn(2+), Ni(2+), Co(2+), Mn(2+), Cd(2+) and Pb(2+). The direct fluorescence detection of these metal ions with high sensitivity at lower ppt levels, typically 2-7 × 10(-11) M (potentially sub-ppt), was successfully achieved. While separation of anionic compounds using a counter cation ("Ion Association (IA)" mode) is typically controlled by the ion association equilibrium constants, K(ass), it was found that differences in the mobilities, μ(ep(IAC)), of the ion association complexes formed between the probe complexes and counter cations are the driving forces for separation in this new method. This suggests that each of the polybrene-probe complexes has different chemical structures among metal ions, which were able to be determined by CD spectra in this investigation. This novel separation mode was termed the "Ion Association Complex (IAC)" mode, distinct from the IA mode.     

Highly sensitive, selective, and rapid fluorescence Hg2+ sensor based on DNA duplexes of poly(dT) and graphene oxide

Coupling T base with Hg(2+) to form stable T-Hg(2+)-T complexes represents a new direction in detection of Hg(2+). Here a graphene oxide (GO)-based fluorescence Hg(2+) analysis using DNA duplexes of poly(dT) that allows rapid, sensitive, and selective detection is first reported. The Hg(2+)-induced T(15)-(Hg(2+))(n)-T(15) duplexes make T(15) unable to hybridize with its complementary A(15) labelled with 6'-carboxyfluorescein (FAM-A(15)), which has low fluorescence in the presence of GO. On the contrary, when T(15) hybridizes with FAM-A(15) to form double-stranded DNA because of the absence of Hg(2+), the fluorescence largely remains in the presence of GO. A linear range from 10 nM to 2.0 μM (R(2) = 0.9963) and a detection limit of 0.5 nM for Hg(2+) were obtained under optimal experimental conditions. Other metal ions, such as Al(3+), Ag(+), Ca(2+), Ba(2+), Mg(2+), Zn(2+), Mn(2+), Co(2+), Pb(2+), Ni(2+), Cu(2+), Cd(2+), Cr(3+), Fe(2+), and Fe(3+), had no significant effect on Hg(2+) detection. Moreover, the sensing system was used for the determination of Hg(2+) in river water samples with satisfactory results.     

Electrochemical aptasensor for detection of copper based on a reagentless signal-on architecture and amplification by gold nanoparticles

A highly sensitive and specific electrochemical aptasensor for Cu(2+) detection based on gold nanoparticles (AuNPs) is presented. In this work, AuNPs offered a big surface area to immobilize a large number of aptamers and excellent electrochemical signal transduction. Its high sensitivity, low detection limit, and wide detection range are the main advantages over our former copper aptasensor. The peak current increased proportionally to the Cu(2+) concentration over the range from 0.1 nM to 10 μM with a detection limit of 0.1 pM. The presence of other divalent metal ions did not affect the detection of Cu(2+), which indicates a high specificity of Cu(2+) detection could be detected. Rapidity, simplicity, and excellent selectivity make it suitable for practical use in determination of Cu(2+) from lake samples.     

Structural and electronic characterization of the complexes obtained by the interaction between bare and hydrated first-row transition-metal ions (Mn(2+), Fe(2+), Co(2+), Ni(2+), Cu(2+), Zn(2+)) and glycine

The complexes formed by the simplest amino acid, glycine, with different bare and hydrated metal ions (Mn(2+), Fe(2+), Co(2+), Ni(2+), Cu(2+), Zn(2+)) were studied in the gas phase and in solvent in order to give better insight into the field of the metal ion-biological ligand interactions. The effects of the size and charge of each cation on the organization of the surrounding water molecules were analyzed. Results in the gas phase showed that the zwitterion of glycine is the form present in the most stable complexes of all ions and that it usually gives rise to an eta(2)O,O coordination type. After the addition of solvation sphere, a resulting octahedral arrangement was found around Ni(2+), Co(2+), and Fe(2+), ions in their high-spin states, whereas the bipyramidal-trigonal (Mn(2+) and Zn(2+)) or square-pyramidal (Cu(2+)) geometries were observed for the other metal species, according to glycine behaves as bi- or monodentate ligand. Despite the fact that the zwitterionic structure is in the ground conformation in solution, its complexes in water are less stable than those obtained from the canonical form. Binding energy values decrease in the order Cu(2+) > Ni(2+) > Zn(2+) approximately Co(2+) > Fe(2+) > Mn(2+) and Cu(2+) > Ni(2+) > Mn(2+) approximately Zn(2+) > Fe(2+) > Co(2+) for M(2+)-Gly and Gly-M(2+) (H(2)O)(n) complexes, respectively. The nature of the metal ion-ligand bonds was examined by using natural bond order and charge decomposition analyses.     

Colorimetric detection of Fe3+ ions using pyrophosphate functionalized gold nanoparticles

A sensitive, selective colorimetric Fe(3+) detection method has been developed by using pyrophosphate functionalized gold nanoparticles (P(2)O(7)(4-)-AuNPs). Gold nanoparticles were prepared by reducing HAuCl(4) with sodium borohydride, in the presence of Na(4)P(2)O(7). IR spectra suggested that pyrophosphates were capped on the surface of the gold nanoparticles. Aggregation of P(2)O(7)(4-)-AuNPs was induced immediately in the presence of Fe(3+) ions, yielding a color change from pink to violet. This Fe(3+)-induced aggregation of P(2)O(7)(4-)-AuNPs was monitored using first the naked eye and then UV-vis spectroscopy with a detection limit of 5.6 μM. The P(2)O(7)(4-)-AuNPs bound by Fe(3+) showed excellent selectivity compared to other metal ions (Ca(2+), Cd(2+), Co(2+), Fe(2+), Hg(2+), K(+), Mg(2+), Mn(2+), Na(+), Ni(2+), Pb(2+), and Zn(2+)). The best detection of Fe(3+) was achieved in a pH range from 3 to 9. In addition, the P(2)O(7)(4-)-AuNPs were also used to detect Fe(3+) in lake water samples, with low interference.     

A colorimetric sensor based on catechol-terminated mixed self-assembled monolayers modified gold nanoparticles for ultrasensitive detections of copper ions

A colorimetric sensor for Cu(II) ions has been developed based on mixed self-assembled monolayers (SAMs) modified gold nanoparticles (AuNPs). The AuNPs were modified with mixed SAMs consisting of mercaptosuccinic acid and the product of electrochemically triggered Michael addition reaction of 4-thiouracil and catechol. In the presence of Cu(II) ions, the coordination of Cu(2+) to catechol-terminated AuNPs leads to aggregation-induced changes of surface plasmon resonance. The cost-effective chemical sensor allows rapid, sensitive and selective detection of Cu(2+) ions, indicating its potential application in environmental field.     

Synthesis and characterization of copper-, zinc-, manganese-, and cobalt-substituted dimeric heteropolyanions, [(alpha-XW9O33)2M3(H2O)3](n-) (n = 12, X =As(III), Sb(III), M = Cu(2+), Zn(2+); n = 10, X = Se(IV), Te(IV), M = Cu(2+) and [(alpha-AsW9O33)2WO(H2O)M2(H2O)2](10-) (M = Zn(2+), Mn(2+), Co(2+)

Interaction of the lacunary [alpha-XW9O33](9-) (X = As(III), Sb(III)) with Cu(2+) and Zn(2+) ions in neutral, aqueous medium leads to the formation of dimeric polyoxoanions, [(alpha-XW9O33)2M3(H2O)3](12-) (M = Cu(2+), Zn(2+); X = As(III), Sb(III)), in high yield. The selenium and tellurium analogues of the copper-containing heteropolyanions are also reported: [(alpha-XW9O33)2Cu3(H2O)3](10-) (X = Se(IV), Te(IV)). The polyanions consist of two [alpha-XW9O33] units joined by three equivalent Cu(2+) (X = As, Sb, Se, Te) or Zn(2+) (X = As, Sb) ions. All copper and zinc ions have one terminal water molecule resulting in square-pyramidal coordination geometry. Therefore, the title anions have idealized D3h symmetry. The space between the three transition metal ions is occupied by three sodium ions (M = Cu(2+), Zn(2+); X = As(III), Sb(III)) or potassium ions (M = Cu(2+); X = Se(IV), Te(IV)) leading to a central belt of six metal atoms alternating in position. Reaction of [alpha-AsW9O33](9-) with Zn(2+), Co(2+), and Mn(2+) ions in acidic medium (pH = 4-5) results in the same structural type but with a lower degree of transition-metal substitution, [(alpha-AsW9O33)2WO(H2O)M2(H2O)2](10-) (M = Zn(2+), Co(2+), Mn(2+)). All nine compounds are characterized by single-crystal X-ray diffraction, IR spectroscopy, and elemental analysis. The solution properties of [(alpha-XW9O33)2Zn3(H2O)3](12-) (X = As(III), Sb(III)) were also studied by 183W-NMR spectroscopy.     

Colorimetric and fluorescent signaling of Au3+ by desulfurization of thiocoumarin

We investigated the chemosignaling of Au(3+) by the selective desulfurization of thiocoumarin. In the presence of a heavy metal ion chelator N,N,N',N'-tetrakis-(2-pyridylmethyl)ethylenediamine, thiocoumarin was selectively converted to its oxo analogue by reaction with Au(3+), resulting in a pronounced chromogenic and fluorescent signaling. Selective signaling of Au(3+) was possible in the presence of common alkali, alkaline earth, and transition metal ions, as well as Au(+) in a mixed aqueous environment. The colorimetric determination of Au(3+) was possible by the color change from pink to yellowish green of the designed probe. The detection limit for the determination of Au(3+) in 50% aqueous acetonitrile was 1.1 × 10(-7) M.