A high-sensitive amperometric hydrogen peroxide biosensor based on the immobilization of hemoglobin on gold colloid/L-cysteine/gold colloid/nanoparticles Pt-chitosan composite film-modified platinum disk electrode

A hemoglobin (Hb)/gold colloid (nano-Au)/L-cysteine (L-cys)/nano-Au/nanoparticles Pt (nano-Pt)-chitosan (CHIT) composite film-modified platinum disk electrode (abbreviated to modified electrode) has been prepared to construct a biosensor for determination of H(2)O(2). The electrochemical characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The modified process was characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The morphologies of different composite film were investigated with scanning electron microscopy (SEM) and the element of composite film was investigated with X-ray photoelectron spectroscopy (XPS). Analytical parameters such as pH and temperature were also studied. The linear range for the determination of H(2)O(2) is 1.4 x 10(-7) to 6.6 x 10(-3)mol/L with a detection limit of 4.5 x 10(-8)mol/L (S/N=3). The sensor achieved 95% of the steady-state current within 10s. The sensor exhibited high sensitivity (17.62 microA/(mmol L)), selectivity and stability. The method is applied to the determination of H(2)O(2) with satisfactory results.     

石墨烯基纳米复合物修饰印刷电极伏安法测定水中镉

构建了基于石墨烯(GS) -纳米金(Au)复合纳米微粒修饰印刷电极(SPCEs)的电化学传感器(SPCEs |GS/Au),建立了微分脉冲溶出伏安(DPSV)法测定水中痕量镉的电分析方法.采用扫描电镜(SEM)对电极表面进行了表征,DPSV法研究了镉的电化学性质.在优化实验条件下,溶出峰电流与Cd2+的质量浓度在2.5...     

混合溶剂对溶胶-凝胶法制备的Li3V2(PO4)3/C高倍率性能的影响

以有机-水为混合溶剂, 采用溶胶-凝胶法制备锂离子电池正极材料Li₃V₂(PO₄)₃/C, 选取乙醇、乙二醇和1,2-丙二醇为有机溶剂, 聚丙烯酸(PAA)为碳源和螯合剂. 通过X射线衍射(XRD)、扫描电镜(SEM)、恒流充放电以及循环伏安测试等方法, 研究了产物的结构形貌及电化学性能. XRD测试结果表明所有溶剂制备的样品结晶良好, 有机溶剂的加入不影响Li₃V₂(PO₄)₃材料的晶型结构. 恒流充放电结果表明有机溶剂的加入改善了材料的电化学性能. 以1,2-丙二醇-水为溶剂的样品电化学性能最好, 在3.0-4.5 V电压范围内, 0.1C (1C=150 mA·g^-1)倍率首次放电比容量为132.89 mAh·g^-1, 10C倍率首次放电比容量达125.42 mAh·g^-1, 循环700周后容量保持率为95.79%, 具有良好的倍率性能与循环性能; 在3.0-4.8 V电压范围内倍率性能较差. 扫描电镜结果表明混合溶剂制备的样品呈片状和针状, 这种形状有利于锂离子的扩散, 因此提高了材料的电化学性能.     

有机溶剂中微量水分的测定

绕丹宁与水在有机溶剂中发生诱导荷移反应,产生吸收光谱移动且吸收峰增大。基于此,优化了实验条件,建立了一种快速、简便、灵敏的测定有机溶剂中微量水分的新方法。甲醇、醋酸溶剂中的水分含量分别在3％-10％（φ）、0～4％（φ）范围及乙醇、1-丙醇、丙酮、乙酸乙酯溶剂中水分含量在0～5％（φ）范围内与吸光度（A）呈线性关系。其相关系数分别是0．9992、0．9996、0．9992、0．9982、0．9990和0．9995。使用本方法测定了灯用酒精中水分含量,结果令人满意。     

A sensitive and highly stable electrochemical impedance immunosensor based on the formation of silica gel-ionic liquid biocompatible film on the glassy carbon electrode for the determination of aflatoxin B1 in bee pollen

The paper describes a sensitive and highly stable label-free electrochemical impedance immunosensor for the determination of aflatoxin B₁ (AFB₁), which is based on the formation of silica gel-ionic liquid biocompatible film on the glassy carbon electrode. The electrochemical performances of the sensor were investigated by electrochemical impedance spectroscopy using a Fe(CN)₆^3−/4− phosphate buffer solution as base solution for test. As new ionic liquid, 1-amyl-2,3-dimethylimidazolium hexafluorophosphate, offers a very biocompatible microenvironment for AFB₁ antibody, the sensor exhibits good repeatability (RSD = 1.2%), sensitive electrochemical impedance response to AFB₁ in the range of 0.1-10 ng ml⁻¹ and lowers the detection limit of AFB₁ (0.01 ng ml⁻¹)_. The electron-transfer resistance change of the sensor after and before incubation with AFB₁ of 2.0 ng ml⁻¹ can retain 95% over a 180-day storage period at 4 °C. The results present a remarkable improvement of sensitivity (2-fold) and long-term stability (190-fold) when compared to classical silica gel sensor. Moreover, proposed sensor has a high selectivity to AFB₁ alone with no significant response to AFB₂, AFG₁, AFG₂ and AFM₁ as single substrates, it has been successfully applied to the determination of trace AFB₁ in bee pollen samples with a spiked recovery in the range of 96.0-102.5%.     

Ag/CuS/rGO复合材料的制备及对亚硝酸盐的电化学传感性能研究

以溶剂热法制备Cu3(BTC)2为前驱体,通过两步转化得到Ag/CuS/rGO复合材料,构制了电化学传感器,研究了其对NO2^-离子的电催化行为,建立了测定NO2^-离子的电化学分析方法。Ag/CuS/rGO复合材料对NO2^-离子展现了良好的电催化性能,检测线性范围为1~50μmol/L和50~550μmol/L,检出限为0.04μmol/L(S/N=3)。该传感器具有制作简单、选择性好和检出限低的特点,拓展了金属有机框架材料(MOFs)在电化学领域的应用。     

A model of polyelectrolyte conductance in moist solvents as a basis of water sensors

The conductance of interpenetrated polymer networks (IPNs) containing quaternary amino groups was studied in cyclohexane, toluene, ethyl ether, ethyl acetate, and tetrahydrofurane as a function of water content by electrochemical impedance spectroscopy. IPNs were then used as sensitive materials to detect water traces in organic solvents with promising results for the construction of a moisture sensor. The detection onset for water concentration increased with the dielectric constant of the solvent. Different IPN-based sensors in the same solvent showed a detection limit at lower water concentration if their characteristic plot [conductance/relative humidity (RH%) in air] was shifted toward lower RH%. This suggests that the composition of this class of polymers can be tuned to achieve the best performance for each solvent.     

二氧化钛纳米颗粒/还原氧化石墨烯修饰玻碳电极在对硝基苯酚检测中的应用

本文报道了用二氧化钛纳米颗粒（TiO₂NPs）/还原氧化石墨烯（RGO）的复合物修饰玻碳电极检测微量对硝基苯酚（4-NP）的电化学方法. 本研究用扫描电子显微镜（SEM）对该复合材料形貌进行表征,用循环伏安法和交流阻抗谱对该复合物电极的电化学性能进行检测,表现出良好的电化学特性,采用差分脉冲伏安法对4-NP进行微量检测,结果令人满意,这主要得益于TiO2NPs/RGO复合物对4-NP有较高的催化活性,其电流峰值与浓度呈较高的线性关系,DPV的检测范围为10μmol·L^-1 ~ 350μmol·L^-1,检测限为0.13 μmol·L^-1. 与其他报道的一些电化学传感器相比,该传感器检测范围大,检测限低,且工作稳定,成本低,分析简单快速,具有很好的应用前景.     

Electrochemical Sensor for Sensitive Determination of Capsaicin Using Pd Decorated Reduced Graphene Oxide

In this work, the reduced graphene oxide functionalized with poly dimethyl diallyl ammonium chloride (PDDA) modified palladium nanoparticles (PDDA‐rGO/Pd) had been facile synthesized and used as the sensing layer for sensitive determination of capsaicin. The prepared composite was characterized by transmission electron microscopy, UV‐visible absorption spectroscopy. The image demonstrated that Pd nanoparticles were uniformly distributed on the graphene surface. The electrochemical properties of the prepared sensor were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results showed that the nanocomposite exhibits attractive electrocatalytic activity towards the oxidation of capsaicin. This attributed to the synergistic action of the excellent properties of Pd nanoparticles and graphene nanosheets. Under optimized conditions, the electrochemical sensor possessed a dynamic linear range from 0.32 μM to 64 μM with a detection limit of 0.10 μM (S/N=3) for capsaicin detection. Moreover, the cost‐effective and simple fabrication procedure, good reproducibility and stability as well as acceptable accuracy for capsaicin determination in actual samples are also the main advantages of this method, which might have broad application in other amide alkaloid detection.     

Conducting polymer engineered covalent organic framework as a novel electrochemical amplifier for ultrasensitive detection of acetaminophen

Two-dimensional covalent organic framework(COF) has distinctive properties that offer potential opportunities for developing advanced electrode materials.In this work,a core-shell material composed of TAPB-DMTP-COF(TAPB,1,3,5-tris(4-aminophenyl)benzene;DMTP,2,5-dimethoxyterephaldehyde)core and conducting polymer shell,TAPB-DMTP-COF@PANI,was synthesized solvothermally using a polymerization method.The structural cha racteristics of the prepared composite were revealed by X-ray diffraction patterns(XRD),fourier transform infrared spectra(FTIR),X-ray photoelectron spectroscopy(XPS),transmission electron microscopy(TEM).The electrochemical analyses were verified by subsequent monitoring of trace levels of acetaminophen.This resultant composite not only facilitated acetaminophen to interact with absorption sites by π-π stacking effect and hydrogen bonding but also overcame the poor conductivity of COF.Under the optimal conditions,a low limit of detection of0.032 μmol/L and wide linear range of 0.10-500 μmol/L were obtained.The electrochemical platform was almost unaffected by other interfering substances,and successfully applied for the practical detection of acetaminophen in commercial tablet,human blood serum and urine.The enhanced performance makes this COF based core-shell composite a promising material in electrochemical senso r.     

A novel nitrite sensor based on graphene/polypyrrole/chitosan nanocomposite modified glassy carbon electrode

A novel nitrite sensor was fabricated based on a graphene/polypyrrole/chitosan nanocomposite film modified glassy carbon electrode. The nanocomposite film was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy and Raman spectroscopy. The electron transfer behaviour of the modified electrodes was investigated in [Fe(CN)(6)](3-)/(4-) redox probe using cyclic voltammetry and electrochemical impedance spectroscopy. Differential pulse voltammetry and amperometry were used to study the electrochemical properties of the proposed sensor. Under optimum conditions, the sensor exhibited good reproducibility and stability for nitrite determination. Linear response was obtained in the range of 0.5-722 μM with a detection limit of 0.1 μM (S/N = 3) for nitrite determination.     

Conducting Polymer/Ionic Liquid Composite Modified Carbon Paste Electrode for the Determination of Carbaryl in Real Samples

A new method has been described for carbaryl determination using a simple electrochemical sensor. The unique properties of poly‐pPhenylenediamine and ionic liquid were exploited to fabricate carbon paste electrode modified with composite based on conducting polymer/ionic liquid. Electrode surface characterization was performed by electrochemical methods (cyclic voltammetry and electrochemical impedance spectroscopy) and by scanning electron microscopy. Differential pulse voltammetry was employed for the detection of carbaryl in acetate buffer solution. Different parameters affecting the carbaryl response were optimized such as ionic liquid amounts, cycle number of polymerization and monomer concentration, pH, and accumulation time. Under the optimum experimental conditions, a linear response was obtained between 0.5 and 200 μmol/L, with detection limit of 0.09 μmol/L. The developed sensor offered satisfactory results for carbaryl detection in spring water and fruit samples.     

基于羧基化多壁碳纳米管修饰玻碳电极快速检测氨基脲的研究

基于羧基化多壁碳纳米管修饰的玻碳电极(CMWCNTs/GCE),构建了一种灵敏检测氨基脲(SEM)的电化学传感器.采用傅里叶变换红外光谱、透射电子显微镜、电化学阻抗谱对修饰材料进行表征.结果表明,羧基化的多壁碳纳米管出现羧基碳氧双键的红外特征峰,管径明显减小,长度变短,电化学阻抗值显著减小.在1 mol/L HAc-NaAc缓冲液中,利用循环伏安法和时间-电流曲线研究了SEM在CMWCNTs修饰电极上的电化学行为.SEM在修饰电极上呈现不可逆的氧化峰.与裸电极相比,氧化峰电流明显增大.在最佳实验条件(pH 7.0,扫描速度为0.1 V/s)下,测得SEM在5.00×10-6~1.09×10-3mol/L浓度范围内与氧化峰电流呈线性关系,线性方程为IP(μA)=-0.472+0.0599C(μmol/L),相关系数r=0.997,检出限为1.88×10-7 mol/L(S/N=3).在实际猪肝样品检测中加标回收率为92.8%~98.0%.     

Nano composite system based on coumarin derivative–titanium dioxide nanoparticles and ionic liquid: Determination of levodopa and carbidopa in human serum and pharmaceutical formulations

The combination of coumarin derivative (7-(1,3-dithiolan-2-yl)-9,10-dihydroxy-6H-benzofuro[3,2-c]chromen-6-on), (DC)–titanium dioxide nanoparticles (TiO₂) and ionic liquid (IL) yields nanostructured electrochemical sensor, formed a novel kind of structurally uniform and electrocatalytic activity material. This new ionic liquid–TiO₂ nanoparticles modified carbon paste electrode (IL–CTP) due to its enhanced conductivity presented very large current response from electroactive substrates. The modified electrode was characterized by different methods including a scanning electron microscope (SEM), electrochemical impedance spectroscopy (EIS) and voltammetry. A pair of well-defined quasi reversible redox peaks of coumarin derivative was obtained at the modified carbon paste electrode (DC/IL–CTP) by direct electron transfer between the coumarin derivative and the CP electrode. Dramatically enhanced electrocatalytic activity was exemplified at the DC/IL–CTP electrode, as an electrochemical sensor to study the electro oxidation of levodopa (LD) and carbidopa (CD). Based on differential pulse voltammetry (DPV), the oxidation of LD and CD exhibited the dynamic range between 0.10– 900.0 μM and 20.0–900.0 μM respectively, and the detection limit (3σ) for LD and CD were 41 nM and 0.38 μM, respectively. DPV was used for simultaneous determination of LD and CD at the DC/IL–CTP electrode, and quantitation of LD and CD in some real samples (such as tablets of Parkin-C Fort and Madopar, Sinemet, water, urine, and human blood serum) by the standard addition method.     

Highly sensitive fluorescent sensing for water based on poly(m-aminobenzoic acid)

Fluorescent conjugated polymer, poly(3-aminobenzoic acid), as a new class of fluorescence sensor for detection of trace amounts of water in organic solvents was developed. This sensor exhibits extraordinarily high sensitivity with a detection limit as low as 0.008 wt% for water in DMF.     

3D石墨烯修饰的猛杀威分子印迹电化学传感器的制备

以猛杀威为模板分子、丙烯酰胺( AM)为功能单体、马来松香丙烯酸乙二醇酯( EGMRA)为交联剂、自制的3D石墨烯(3D-rGO)为增敏材料,在玻碳电极表面合成分子印迹聚合物,制备检测猛杀威的分子印迹电化学传感器。运用扫描电镜(SEM)对自制3D石墨烯的形貌进行了表征,通过循环伏安法(CV)、差分脉冲伏安法(DPV)和交流阻抗法(EIS)对猛杀威传感器的性能进行了研究。结果表明,猛杀威的浓度在8.0×10-8~8.0×10-6 mol/L范围内与响应电流值呈良好的线性关系,线性相关系数R=0.9954,检出限为7.3×10-8 mol/L (S/N=3),猛杀威分子印迹敏感膜的印迹因子β=3.88,且相对于3种结构类似物的选择因子α垌1,说明此传感器具有良好的选择性。将此传感器应用于生菜样品检测,加标回收率在96.7%~98.7%之间。     

Simplified version of the sodium salicylate method for analysis of nitrate in drinking waters

The salicylate method for determination of nitrate in drinking waters has been simplified by using the calibration solutions for 54 days, and therefore, reducing the work time. The results obtained can be considered satisfactory with regard to limit of determination (0.10 mg l⁻¹ nitrate as nitrogen (NO₃⁻-N)), precision (relative standard deviations <4% for five determinations were found) and accuracy (recoveries from 88 to 106% for nitrate in spiked drinking water were obtained).     

Simultaneous electrochemical determination of nitrate and nitrite in aqueous solution using Ag-doped zeolite-expanded graphite-epoxy electrode

In this work a new electrochemical sensor based on an Ag-doped zeolite-expanded graphite-epoxy composite electrode (AgZEGE) was evaluated as a novel alternative for the simultaneous quantitative determination of nitrate and nitrite in aqueous solutions. Cyclic voltammetry was used to characterize the electrochemical behavior of the electrode in the presence of individual or mixtures of nitrate and nitrite anions in 0.1 M Na₂SO₄ supporting electrolyte. Linear dependences of current versus nitrate and nitrite concentrations were obtained for the concentration ranges of 1-10 mM for nitrate and 0.1-1 mM for nitrite using cyclic voltammetry (CV), chronoamperometry (CA), and multiple-pulsed amperometry (MPA) procedures. The comparative assessment of the electrochemical behavior of the individual anions and mixtures of anions on this modified electrode allowed determining the working conditions for the simultaneous detection of the nitrite and nitrate anions. Applying MPA allowed enhancement of the sensitivity for direct and indirect nitrate detection and also for nitrite detection. The proposed sensor was applied in tap water samples spiked with known nitrate and nitrite concentrations and the results were in agreement with those obtained by a comparative spectrophotometric method. This work demonstrates that using multiple-pulse amperometry with the Ag-doped zeolite-expanded graphite-epoxy composite electrode provides a real opportunity for the simultaneous detection of nitrite and nitrate in aqueous solutions.     

基于金属有机框架结构的分子印迹聚合物电化学传感器检测猪尿中苯乙醇胺A

以苯乙醇胺 A ( PEA )为模板分子、对氨基苯硫酚( PATP )为功能单体和有机配体、金纳米颗粒( AuNPs)为金属中心,通过原位电聚合在金电极表面成功制备了具有金属有机框架( MOFs)结构的分子印迹聚合物( MIP)复合膜,构建了具有分子识别特性的复合膜电化学传感器,实现了对PEA的灵敏检测。采用电化学技术和扫描电镜对修饰电极进行表征。优化了扫描速率、pH值、洗脱时间和富集时间等检测条件。在优化条件下,此电化学传感器对PEA在1.0×10-13~1.0×10-9 mol/L范围内有很好的线性关系,相关系数达到0.996,检出限为1.0×10-13 mol/L。在猪尿液中添加不同浓度的PEA,回收率在92.7%~108.4%,相对标准偏差小于8.0%。本方法对实际猪尿中PEA的检测具有很好的灵敏度、特异性和稳定性。     

Construction and analytical application of a biosensor based on stearic acid-graphite powder modified with sweet potato tissue in organic solvents

A biosensor based on stearic acid-graphite powder modified with sweet potato (Ipomoea batatas (L.) Lam.) tissue as peroxidase source was constructed and applied in organic solvents. Several parameters were studied to evaluate the performance of this biosensor such as stearic acid-graphite powder and tissue composition, type and concentration of supporting electrolyte, organic solvents, water/organic solvent ratio (% v/v) and hydrogen peroxide concentration. After selection of the best conditions, the biosensor was applied for the determination of hydroquinone in cosmetic creams in methanol. At the peroxidase electrode hydroquinone is oxidized in the presence of hydrogen peroxide and the radical formed was reduced back electrochemically at -180 mV vs Ag/AgCl (3.0 mol L(-1) KCl). The reduction current obtained was proportional to the concentration of hydroquinone from 6.2 x 10(-5) to 1.5 x 10(-3) mol L(-1) (r = 0.9990) with a detection limit of 8.5 x 10(-6) mol L(-1). The recovery of hydroquinone from two samples ranged from 98.8 to 104.1% and an RSD lower than 1.0% for a solution containing 7.3 x 10(-4) mol L(-1) hydroquinone and 1.0 x 10(-3) mol L(-1) hydrogen peroxide in 0.10 mol L(-1) tetrabutylammonium bromide methanol-phosphate buffer solution (95:5% v/v) (n = 10) was obtained.