Combining AlCl3·6H2O and an ionic liquid to prepare chlorohydrin esters from glycerol

We describe here the first example in which glycerol has been transformed into chlorohydrin esters using an ionic liquid and hydrated aluminium chloride. The method avoids using Crown-18 ether, which was needed to obtain a similar yield when KCl was used. Alkyl and aryl acids can be used, although yields are very dependent on the carboxylic acid used.     

A tandem Finkelstein-rearrangement-elimination reaction: a straightforward synthetic route to allyl esters

Allyl esters can be obtained by a Finkelstein-rearrangement-elimination reaction of 2-chloro-1-(chloromethyl)ethyl esters induced by NaI. Sodium iodide can be used below equivalence using a reductive agent as sodium thiosulfate. High yields are obtained with most of the diverse esters studied. The method described avoids the use of allyl alcohol as a reagent. 2-Chloro-1-(chloromethyl)ethyl esters are prepared from glycerol, the main by-product of biodiesel industry. The effectiveness of iodine as reagent to hydrolyze allyl esters is also confirmed.     

Experimental and theoretical investigation of the kinetics of the reaction of atomic chlorine with 1,4-dioxane

The rate coefficients for the reaction of 1,4-dioxane with atomic chlorine were measured from T = 292-360 K using the relative rate method. The reference reactant was isobutane and the experiments were made in argon with atomic chlorine produced by photolysis of small concentrations of Cl2. The rate coefficients were put on an absolute basis by using the published temperature dependence of the absolute rate coefficients for the reference reaction. The rate coefficients for the reaction of Cl with 1,4-dioxane were found to be independent of total pressure from p = 290 to 782 Torr. The experimentally measured rate coefficients showed a weak temperature dependence, given by k(exp)(T) = (8.4(-2.3)(+3.1)) × 10(-10) exp(-(470 ± 110)/(T/K)) cm3 molecule (-1) s(-1). The experimental results are rationalized in terms of statistical rate theory on the basis of molecular data obtained from quantum-chemical calculations. Molecular geometries and frequencies were obtained from MP2/aug-cc-pVDZ calculations, while single-point energies of the stationary points were computed at CCSD(T) level of theory. The calculations indicate that the reaction proceeds by an overall exothermic addition-elimination mechanism via two intermediates, where the rate-determining step is the initial barrier-less association reaction between the chlorine atom and the chair conformer of 1,4-dioxane. This is in contrast to the Br plus 1,4-dioxane reaction studied earlier, where the rate-determining step is a chair-to-boat conformational change of the bromine-dioxane adduct, which is necessary for this reaction to proceed. The remarkable difference in the kinetic behavior of the reactions of 1,4-dioxane with these two halogen atoms can be consistently explained by this change in the reaction mechanism.     

Spectroscopic studies of zinc(II)tetraphenylporphyrin molecular complex with 1,4-dioxane

The molecular complex of zinc(II)tetraphenylporphyrin with 1,4-dioxane has been obtained. The IR spectra of the [Zn(TPhP)(1,4-dioxane)2] stabile molecular complex between 4000 and 50cm(-1) have been studied. An interpretation is given on the base the "chair" conformation of 1,4-dioxane molecule.     

Facile synthesis of glycerol carbonate from glycerol using selenium‐catalyzed carbonylation with carbon monoxide

The commercial production of glycerol has increased considerably for several years, because of its rising inevitable formation as a by‐product of biodiesel. For the effective utilization of glycerol, a new synthesis of glycerol carbonate (4‐hydroxymethyl‐2‐oxo‐1,3‐dioxolane) that is used as solvents and raw material of plastics from glycerol was explored. By combined the selenium‐catalyzed carbonylation of slightly excess of glycerol with carbon monoxide and potassium carbonate under 0.1 MPa at 20°C for 4 h in DMF with the oxidation of resulting selenocarbonate salt with molecular oxygen (0.1 MPa, 20 °C) for 2 h, glycerol carbonate was obtained in good yields (83–84%). However, sodium hydride to form sodium alkoxide in situ lowered the yield of glycerol carbonate. Use of triethylamine, 1‐methylpyrrolidine, and DBU as bases gave poor results. Furthermore, styrene carbonate was obtained in excellent yield (90%) under similar reaction conditions. The catalytic synthesis of glycerol carbonate was also brought about in the mixed gas atmosphere (carbon monoxide:oxygen = 3:1, 0.1 MPa, 20°C). Glycerol carbonate and styrene carbonate were obtained in reasonable yields (197% and 119%, based on selenium used). © 2010 Wiley Periodicals, Inc. Heteroatom Chem 21:541–545, 2010; View this article online at wileyonlinelibrary.com . DOI 10.1002/hc.20640     

A Novel Layered Silicate with a Helical Morphology

Helices composed of stacked layers are present in the novel silicate obtained from a silica sol and NaOH by hydrothermal synthesis in the presence of tetramethylammonium (TMA) hydroxide and 1,4-dioxane. The helical morphology is evident in scanning electron micrographs (see picture). The TMA and sodium ions of the silicate are readily replaced by protons, and on heating to 200°C a reversible phase transition occurs in which water molecules are lost from between the layers.     

From glycerol to chlorohydrin esters using a solvent-free system. Microwave irradiation versus conventional heating

Esterification-chlorination of glycerol provides chlorohydrin esters in high yields. A ratio of reagents close to equivalence can be used, so that atom economy of the reaction is optimized. The reaction can be carried out using either classical or microwave heating, and no solvent is required. 2-Chloro-1-(chloromethyl)ethyl esters can be obtained in high regioisomeric relationship when either low or moderate temperature is used. In contrast, microwave irradiation allows the use of higher reaction temperatures that render mixtures of both regioisomers in variable relationships. Kinetic control of the process is proposed for classical heating, and experimental results are analyzed with the aid of ab initio calculated values. Non-thermal phenomena can be used to explain the high efficiency of microwave irradiation at low temperature.     

Functional polymers. XLVIII. Polymerization of ω-alkenoate derivatives

Esters of ω-alkenoic acids have been homopolymerized with transition metal initiating systems. The key to the successful polymerization was the complexation of the monomer prior to its addition to the initiating system. Titanium trichloride, aluminum activated, was found to be best as the transition metal part of the initiator systems, with diethyl-, or better, diisobutylaluminum chloride as the reducing agents and n-hexane or toluene as the solvents. Best results for polymerizations were obtained with 2,6-dimethylphenyl esters of the functional α-olefin monomers; however, other phenyl esters also polymerized well. Attempts to polymerize methyl 10-undecenoate gave the corresponding polymer in only low yields. Polymers of the 2,6-dimethylphenyl esters, obtained in high molecular weight, were characterized. Polymers were also obtained from 2,6-dimethylphenyl 7-octenoate, but not from ω-alkenoates with less than three methylene units between the ester group and the terminal olefin group. Poly(2,6-dimethylphenyl 10-undecenoate) was hydrolyzed in an aqueous sodium hydroxide/1,4-dioxane solution to poly(sodium 10-undecenoate) that in turn was neutralized with acetic acid to poly(10-undecenoic acid).     

Enthalpies of 1,4-Dioxane, 1,2-Dimethoxyethane, and Ethylacetate Solvation in the Water–1-Propanol and Water–Glycerol Binary Mixtures

The enthalpies of 1,4-dioxane, 1,2-dimethoxyethane, and ethylacetate solution in binarymixtures of water with 1-propanol and glycerol were measured at 25°C using a precise isoperibol calorimeter. The enthalpies of the solute solvation were calculated and compared with the experimental data for other solutes. The results obtained were interpreted in terms of universal and specific solute solvation using parameters of a solvent polarity. It was found that the extreme shape of the curve _solv H° vs. X for ethylacetate in the mixtures of water with 1-propanol results from peculiarities of carbotylate-group solvation and appears to be not connected with the influence of alcohol microaggregates in the mixed solvent.     

A practical synthesis of trans-3-substituted proline derivatives through 1,4-addition

A practical four-step synthesis of 3-alkyl-, vinyl-, and aryl-substituted proline derivatives, which are important building blocks for conformationally restrained peptide analogs, was developed. The method relies on a Cu-catalyzed 1,4-addition of Grignard reagents to N-protected 2,3-dehydroproline esters, efficiently prepared in a new one-pot protocol. The 1,4-addition products are obtained with good trans-selectivity (dr 5:1 to 25:1). A nonracemic sample of N-Cbz-3-vinylproline (74% ee) was obtained using Evans oxazolidinone as a chiral auxiliary.     

Impurity analysis of 1,4-dioxane in nonionic surfactants and cosmetics using headspace solid-phase microextraction coupled with gas chromatography and gas chromatography-mass spectrometry

1,4-Dioxane impurity in nonionic surfactants and cosmetics were analyzed using solid-phase microextraction (SPME) coupled with gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). Experimental results show that there is no significant difference using SPME-GC and SPME-GC-MS for analysis of 1,4-dioxane in three types of nonionic surfactants at the 95% confidence level. The relative standard deviation (R.S.D.) values of each analytical method were smaller than 3%. The amount of 1,4-dioxane was found to vary from 11.6 +/- 0.3 ppm to 73.5 +/- 0.5 ppm in 30% of nonionic surfactants from manufacturers in Taiwan. These methods were linear over the studied range of 3-150 ppm with correlation coefficients higher than 0.995. The recoveries of 1,4-dioxane for these nonionic surfactants following SPME were all higher than 96 +/- 1% (n = 3). The detection limits of 1,4-dioxane for these nonionic surfactants following SPME were from 0.06 ppm to 0.51 ppm. The experimentally determined level of 1,4-dioxane in cosmetics from manufacturers in Taiwan varied from 4.2 +/- 0.1 ppm to 41.1 +/- 0.6 ppm in 22% of daily used cosmetics following SPME coupled with GC and GC-MS. Conventional solvent extraction takes around 1 h for extraction and reconcentration but SPME takes only around 10 min. SPME provides better analyses of 1,4-dioxane in nonionic surfactants and cosmetics than conventional solvent extraction and head space pretreatments in term of simplicity, speed, precision, detection limit, and solvent consumption.     

Polydentate ligands based on closo-decaborate anion for the synthesis of gadolinium(iii) complexes

A reaction of the closo-decaborate anion 1,4-dioxane derivative with polyatomic alcohols (ethyleneglycol, glycerol, triethanolamine) was studied. These reactions include the ring opening of the cyclic substituent and the addition of the alcohol molecule to boron cluster through the alkoxy spacer chain. The products obtained form coordination compounds upon the reaction with gadolinium(iii) salts, playing the role of polydentate ligands. The compounds obtained were studied by IR spectroscopy, NMR spectroscopy, ESI mass spectrometry, elemental and thermographic analysis.     

A three-component reaction between alkenes, secondary phosphanes, and elemental selenium: a novel, efficient, atom-economic synthesis of diselenophosphinic esters

A novel, convenient, atom-economic approach toward the synthesis of diselenophosphinic esters has been developed via the three-component reaction between aryl- or hetarylalkenes secondary phosphanes, and elemental selenium. The reaction proceeds without a catalyst (85 °C, 3 h, 1,4-dioxane) to afford the target compounds in good to high yields.     

First desymmetrization of 1,3-propanediamine derivatives in organic solvent. Development of a new route for the preparation of optically active amines

The chemical synthesis and enzymatic desymmetrization of a panel of prochiral diamines have been successfully described for the first time using lipases in organic solvents. A family of 2-aryl-1,3-propanediamines has been obtained with high enantiopurity and good yields in the PSL-catalyzed reaction using diallyl carbonate in 1,4-dioxane.     

Glycidyl Esters of Aromatic Acids

Abstract

The reaction of substituted benzoic acids, dicarboxylic acids such as phthalic, terephthalic, and isophthalic acids, and the sodium or potassium salts of these acids with equimolar or excess epichlorohydrin in the presence of benzyltrimethylammonium chloride has been studied using various solvents such as toluene, dioxane, monochlorobenzene, and tetrachloroethylene. Use of the free carboxylic acids gave only fair to low yields of glycidyl esters, while sodium or potassium salts of the carboxylic acids gave excellent yields of materials of high oxirane content. The epoxidation of chlorohydrin esters of these acids by the dehydrochlorination was also studied using various dehydrochlorinating reagents such as NaOH, KOH, Na₂CO₃, and NaAlO₂ in such solvents as water, dichloromethane, dioxane, and monochlorobenzene at various temperatures. Reaction time, reaction temperature, and water content were found to influence the yield of glycidyl esters. It is suggested that the reaction path involves nucleophilic attack upon the terminal position of the epoxide or epichlorohydrin. The resulting alkoxide then reacts further to give either a glycidyl ester or a chlorine-containing by-product, the predominant course depending upon reaction conditions.     

大环聚醚化合物的合成研究(Ⅲ)——6-烷氧基二苯并-16-冠-5的合成

亲脂性强的冠醚化合物对金属离子选择性高、络合性能好,是高效率的相转移催化剂。对于二苯并型大环冠醚,在其芳环上引入烷基是增强冠醚脂溶性的一种有效途径;在其冠醚的脂环上引入烷氧基是提高冠醚脂溶性的又一方便的方法。为此,我们将开链冠醚(Ⅰ)与环氧氯丙烷反应得到6-羟基二苯并-16-冠-5(Ⅰ)。(Ⅱ)转化为钠盐。钠盐分别和硫酸二甲酯及7种卤代烃缩合成一组带有6-烷氧基的二苯并型冠醚化合物Ⅲ_(a—h)。反应为:     

Synthesis and some chemical conversions of acetylenic derivatives of 1,4-dioxane

The possibility has been shown of synthesizing acetylenic derivatives of 1,4-dioxane in high yield by the interaction of glycidyl ethers of acetylenic alcohols with ethylene bromohydrin in the presence of boron trifluoride etherate. Dehydrobromination of the corresponding bromohydrin was then carried out in the presence of metallic sodium in absolute diethyl ether. Acetylenic derivatives of 1,4-dioxane enter into hydrosilylation, aminomethylation, and diene condensation reactions with the formation of new derivatives of 1,4-dioxane.     

Solubility and preferential solvation of indomethacin in 1,4-dioxane + water solvent mixtures

The solubilities of indomethacin (IMC) in 1,4-dioxane + water cosolvent mixtures were determined at several temperatures, 293.15–313.15 K. The thermodynamic functions: Gibbs energy, enthalpy, and entropy of solution and of mixing were obtained from these data by using the van’t Hoff and Gibbs equations. The solubility was maximal in 0.95 mass fraction of 1,4-dioxane and very low in pure water at all the temperatures. A non-linear plot of ΔH_soln ° vs. ΔG_soln ° with negative slope from pure water up to 0.60 mass fraction of 1,4-dioxane and positive beyond this up to 0.95 mass fraction of 1,4-dioxane was obtained. Accordingly, the driving mechanism for IMC solubility in water-rich mixtures is the entropy, probably due to water-structure loss around the drug non-polar moieties by 1,4-dioxane, whereas, above 0.60 mass fraction of 1,4-dioxane the driving mechanism is the enthalpy, probably due to IMC solvation increase by the co-solvent molecules. The preferential solvation of IMC by the components of the solvent was estimated by means of the quasi-lattice quasi-chemical method, whereas the inverse Kirkwood-Buff integral method could not be applied because of divergence of the integrals in intermediate compositions.     

Optimization of conditions for synthesizing sulfonated hydrazides of benzoic and benzenesulfonic acids

The kinetic relationships of arenesulfonation of benzoic and benzenesulfonic acid hydrazides were studied. Based on the data obtained, the conditions for synthesizing these products were optimized. The synthesis can be performed using aqueous-organic solvents containing 2-propanol, 1,4-dioxane, or tetrahydrofuran as nonaqueous component. The thermal stability of benzenesulfohydrazide and its sulfonation product was compared on the basis of data of gas chromatography–mass spectrometry. The fragmentation pathways of the reactants and target product, sulfonated benzenesulfohydrazide, were suggested.     

Enthalpies of dilution and homotactic enthalpic interaction coefficients of THF and 1,4-dioxane at 298.15 k

Enthalpies of dilution at 298.15 K of aqueous solutions of THF and 1,4-dioxane have been determined using flow microcalorimetry. The results obtained were used to determine the homotactic enthalpic interaction coefficients that characterize pair interactions of THF and 1,4-dioxane in aqueous solution. These are briefly discussed from the point of view of intermolecular interaction between the hydrated solute species.