Influence of sintering on the structural and electronic properties of TiO2 nanoporous layers prepared via a non-sol–gel approach

In this work, a nonaqueous method is used to fabricate thin TiO₂ layers. In contrast to the common aqueous sol–gel approach, our method yields layers of anatase nanocrystallites already at low temperature. Raman spectroscopy, electron microscopy and charge extraction by linearly increasing voltage are employed to study the effect of sintering temperature on the structural and electronic properties of the nanocrystalline TiO₂ layer. Raising the sintering temperature from 120 to 600?°C is found to alter the chemical composition, the layer’s porosity and its surface but not the crystal phase. The room temperature mobility increases from 2?×?10^?6 to 3?×?10^?5?cm²/Vs when the sinter temperature is increased from 400 to 600?°C, which is explained by a better interparticle connectivity. Solar cells comprising such nanoporous TiO₂ layers and a soluble derivative of cyclohexylamino-poly(p-phenylene vinylene) were fabricated and studied with regard to their structural and photovoltaic properties. We found only weak polymer infiltration into the oxide layer for sintering temperatures up to 550?°C, while the polymer penetrated deeply into titania layers that were sintered at 600?°C. Best photovoltaic performance was reached with a nanoporous TiO₂ film sintered at 550?°C, which yielded a power conversion efficiency of 0.5?%. Noticeably, samples with the TiO₂ layer dried at 120?°C displayed short-circuit currents and open circuit voltages only about 15–20?% lower than for the most efficient devices, meaning that our nonaqueous route yields titania layers with reasonable transport properties even at low sintering temperatures.     

Studying structural,morphological and optical properties of nanocrystalline ZnO:Ag films prepared by sol–gel method for antimicrobial activity

Pure and Ag-doped zinc oxide sol–gel thin films were prepared by spin-coating process. Pure and Ag–ZnO films, containing 2–8% Ag, were annealed at 500?°C for 2?h. All thin films were prepared and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV–visible spectroscopy. X-ray diffraction studies show the polycrystalline nature with hexagonal wurtzite structure of ZnO and Ag:ZnO thin films. The crystallite size of the prepared samples reduced with increasing Ag doping concentrations. AFM and SEM results indicated that the average crystallite size decreased as Ag doping concentration increased. The transmittance spectra were then recorded at wavelengths ranging from 300 to 1000?nm. The films produced yielded high transmission at visible regions. The optical band gap energy of spin-coated films also decreased as Ag doping concentration increased. In particular, their optical band gap energies were 3.75, 3.55, 3.4, 3.3, and 3.23?eV at 0%, 2%, 4%, 6%, and 8%, respectively. Antibacterial activity of pure and Ag-doped zinc oxide against Escherichia coli and Staphylococcus aureus was evaluated by international recognized test (JIS Z 2801). The results showed that pure and Ag-doped ZnO thin film has an antibacterial inhibition zone against E. coli and S. aureus. Gram-positive bacteria seemed to be more resistant to pure and Ag-doped ZnO thin film than gram-negative bacteria. The test shows incrementally increasing in antibacterial activity of the thin films when dopant ratio increased under UV light.

Open image in new window

     

Investigation of structural,morphological, optical,and magnetic properties of Sm-doped LaFeO3 nanopowders prepared by sol–gel method

Journal of Sol-Gel Science and Technology - Pure orthorhombic phase of La1?xSmxFeO3 (x?=?0, 0.1, 0.2, and 0.3) nanoparticles can be obtained by sol–gel method after...     

Investigation of photocatalytic and low-emissivity properties of TiO2:F films featuring columnar structure prepared on SnO2:F substrate by sol–gel method

Fluorine-doped TiO₂ thin films featuring columnar structure were prepared on fluorine-doped tin oxide (SnO₂:F) substrate using a sol–gel method. The F doping ratios were varied in the range of 0–8 %. The effect of [F]/[Ti + F] ratio on the structural, morphological, optical, photocatalytic and low-emissivity properties has been investigated in detail. X-ray diffraction studies revealed that all the composited films are mainly composed of anatase TiO₂ and rutile SnO₂ without other phases. The prepared TiO₂:F films possessed the columnar morphology with the single layer thickness ranging from 28 to 31 nm. The best photocatalytic activity was obtained for the films with 4 % F doping ratio which is mainly attributed to the highest crystallization and crystallite size. The transmission and hemispherical emissivity of the composite films could still reach approximately 70 % and 0.20, which match the requirements of the Chinese National Standard (GB/T18915.2-2002), promoting the films for the practical applications.     

The effect of heat treatment in the reducing atmosphere on the physical properties of TiO2 thin films prepared by sol–gel method

Multilayered nanostructured TiO₂ thin films were prepared by sol–gel and dipping deposition on quartz substrate followed by thermal treatment under reducing atmosphere (20 %H₂–80 %Ar). Heat treatment at progressively higher temperatures caused structural, morphological, and optical changes, which were investigated by X-ray diffraction (XRD), atomic force microscopy, scanning electron microscopy, and UV–Vis spectroscopy. The conductivities of the thin films were also measured by 4-point probe method. The XRD results showed that the calcined TiO₂ thin films consist of single anatase phase which was completely transformed into rutile phase after heat treatment at 1,000 °C. The grains of films grew by intra-agglomerate densification after heat treatment at higher temperatures. The root mean square roughness of the samples was found to be in the range of 0.58–3.36 nm. The partially reduced TiO₂ samples have red-shifted transmittance bands due to new energy band formed by oxygen vacancies. The electrical conductivity of the films was also enhanced after heat treatment in reducing atmosphere.     

Effect of the variation of metal and cerium loadings on CeO2x–TiO2(100−x) supports in the complete catalytic oxidation of formaldehyde

Research on Chemical Intermediates - Formaldehyde has been successfully converted into CO2 and H2O at low temperature in the presence of CeO2x–TiO2(100?x) mixed oxides prepared by the...     

Polyacrylonitrile molecular weight effect on the structural and magnetic properties of metal–carbon nanomaterial

1. Download high-res image (259KB)
2. Download full-size image

     

Microstructure and hydrogen production activity of Pt–TiO2 prepared by precipitation–photodeposition

A series of Pt–TiO₂ photocatalysts were prepared by a facile precipitation–photoreduction method under different pH conditions, using H₂PtCl₆ as platinum precursor. The microstructure and chemical state of Pt loaded on the surface of TiO₂ were analyzed by X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). It was revealed that the size and distribution of Pt nanoparticles on TiO₂ surface is closely related to the initial pH of H₂PtCl₆ solution. The optimal pH value for forming highly dispersed Pt nanoparticles is 12. The photocatalytic activities of the prepared samples were investigated in terms of hydrogen production. The results indicated that the Pt–TiO₂ sample prepared by precipitation–photodeposition method shows much higher activity than that prepared by traditional photodeposition method.     

Optical and structural properties of aluminium oxide thin films prepared by a non-aqueous sol–gel technique

Clear aluminium oxide sols without precipitation were synthesized via a non-aqueous sol–gel technique using three different alcohols (ethanol, isopropanol and n-butyl alcohol) as solvent, aluminium sec-butoxide as a precursor and acetyl acetone as a chelating agent. Although all sols could be successfully used to prepare thin films, the most stable one was prepared with n-butyl alcohol. Highly transparent, homogenous and amorphous aluminium oxide thin films were obtained on Si substrates after a heat treatment at 500 °C. X-Ray photoelectron spectroscopy (XPS) and Fourier transform infrared absorption (FT-IR) spectroscopy revealed all films were hydroxide free. The optical and structural properties of the films were particularly investigated. Any significant difference except from thickness on the film properties was not observed by changing the alcohol. Refractive index was used as an indication of the porosity of the films and ranged from 1.54 to 1.60.     

Photocatalytic activity of TiO2 films prepared by sol–gel and electrodeposition on the decolourization of monoazo dyes

Journal of Sol-Gel Science and Technology - TiO2 films were prepared effectively using titanium tetraisopropoxide sol by simple electrodeposition technique on conductive indium tin oxide plates...     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Synthesis and characterization of organic–inorganic hybrid materials prepared by sol–gel and containing CdS nanoparticles prepared by a colloidal method using poly(N-vinyl-2-pyrrolidone)

This paper describes the synthesis and characterization of CdS nanoparticles (NPs) stabilized with poly(N-vinyl-2-pyrrolidone) and their further immobilization on a hybrid organic–inorganic matrix produced by the sol–gel process. The production of the hybrid matrix doped with CdS NPs was carried out in two steps. In the first step a precursor, designated diureasil precursor, was synthesized from the reaction between the terminal amine groups of α,ω-diamine-poly(oxyethylene-co-oxypropylene) and the isocyanate group of 3-isocyanatopropyltriethoxysilane. The next step involved the hydrolysis and condensation reactions of ethoxy groups attached to silicon, this step resulting in the formation of a crosslinked siliceous network linked through urea bonds to a poly(oxyethylene)/poly(oxypropylene) chain. The NPs were added to the diureasil precursor before the gelation process to allow a homogeneous dispersion of the NPs within the matrix. The developed method allowed the transfer of colloidal NPs to a solid matrix without the need of exchange the capping agents or the solvent. The materials were characterized by absorption, steady-state photoluminescence spectroscopy and by TEM. The results obtained showed the presence of CdS NPs with quantum size effect dispersed within the diureasil matrix. The obtained nanocomposites show a high transparency in the visible range accounting for the good dispersion of the NPs within the matrix. The TEM analysis confirmed that the NPs are uniformly dispersed within the diureasil matrix.     

Synthesis of ZnO–SnO2 nanocomposites: impact of polyethylene glycol on morphological,luminescence and photocatalytic properties

Research on Chemical Intermediates - Zinc oxide-doped tin dioxide (ZnO–SnO2) nanomaterials were prepared by a sol–gel method with and without different amounts (0.5, 1.0 and...