Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Voltammetric Determination of Trace Amounts of Fenitrothion on a Novel Nano-TiO2 Polymer Film Electrode

A novel nano-TiO₂ polymer modified glassy carbon (GC) electrode was developed for the determination of an organophosphorous pesticide, fenitrothion (-NO₂), in citrate buffer solution. The electrochemical behavior of fenitrothion was characterized by using cyclic voltammetry. An irreversible form, -NO₂, was transformed into a reversible redox couple (-NHOH/-NO), and it can be used to determine trace fenitrothion by square wave voltammetry. The experimental parameters, such as film thickness, pH value, accumulation potential and time were optimized. Interestingly, a cyclic voltammetric scan was observed to be more effective than a constant potential for the accumulation of fenitrothion. A linear response over a fenitrothion concentration of 2.5×10^–8 to 1.0×10^–5M was exhibited, with a detection limit of 1.0×10^–8M (S/N=3). The high sensitivity and selectivity of this film electrode was demonstrated by its practical application to the determination of trace amounts of fenitrothion in lake water and apple samples.     

Au-Induced Faceting of Si(5 5 12)

The growth of Au on the stable, high-index Si(5512) surface has been studied using scanning tunneling microscopy (STM). At very low coverages and moderate annealing temperatures (0.1ML, 400–500°C), Au appears to decorate the underlying Si rows and form an array of rows that maintains the underlying (5512) periodicity of 5.4nm. For higher annealing temperatures and coverages, however, Au causes faceting to a number of nearby planes. The two primary facets formed at lower (0.15ML) and higher (0.5–2ML) coverages are the (337) and (225) planes, which are tilted 0.7° down [towards (111)] and 1.1° up from (5512), respectively. Both orientations are in fact subunits of the (5512) unit cell, so their presence is not surprising. In addition to these facets, two types of sawtooth morphologies composed of planes oriented further from (5512) are found at very high annealing temperatures (800–900°C). These include (113)+(7715) planes at very low coverage (0.05ml) and (113)+(5511) planes at higher coverage (1ML), where (113) is tilted up by 5.3° and (7715) and (5511) are tilted down by 2.9° and 2.2°, respectively. Au adsorption on Si(5512) therefore results in the formation of five possible facet planes: (113), (225), (337), (5511), and (7715).     

Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Solid-Phase Extraction with Slurry Injection of the Resin Into ETAAS for Trace Determination of Thallium in Natural Water

Thallium in natural water samples was determined by electrothermal atomic absorption spectrometry after 1000-fold enrichment by mini solid-phase extraction from a 100-mL sample solution. A Tl-pyrrolidine-1-carbodithioate complex formed in a sample solution of pH 1.6 was extracted on fine particles of a cellulose nitrate resin dispersed in the sample solution. The cellulose nitrate resin was then collected on a membrane filter (25mm^ø) by filtration under suction using a glass funnel with an effective filtration area of 0.64cm². As a result, a circular thin layer of the resin phase with a diameter of 9mm was obtained. Then the resin phase was carved out by an acrylate resin puncher with a 10-mm^ø hole to put it into a sample cup containing 100µL of 10mM HNO₃ containing 0.5mM NaCl. The resin phase was suspended in the solution by ultrasonication. 1000-fold enrichment was thus attained within 15min, and the suspension was delivered to electrothermal atomic absorption spectrometry. The linear calibration graph was obtained in the range of 0–4ng of Tl in 100mL of a sample solution. The detection limit obtained by 3 method was 0.19ng. The proposed method was applied to the determination of Tl in natural water samples. The results showed the concentration of Tl in seawater was 12.1±1.8pgmL^–1 for the calibration graph method and 12.6±1.4pgmL^–1 for the standard addition method. A snowmelt sample contained 20.7±1.0pgmL^–1 of Tl.     

Determination of Trace Proteins by Rayleigh Light Scattering Technique with Indophenol Blue

The interaction of indophenol blue (IPB) with proteins in aqueous solution has been studied by optical absorption and Rayleigh light scattering (RLS) spectroscopy. At pH 3.8, the weak RLS of IPB is enhanced by proteins. Based on this phenomenon, a novel method for the determination of proteins at nanogram levels using the RLS technique is developed. The method is simple, practical and sensitive. The linear range is 0.25–20.9µgmL^–1 for BSA, and 0.25–17.6µgmL^–1 for HSA. The detection limits (S/N=3) are 23ngmL^–1 for BSA and 22ngmL^–1 for HAS. The results for the determination of proteins in human serum samples are very close to those obtained by an established clinical method. There is very little interference from amino acids, metal ions or other coexisting compounds.     

Fluorescence Quenching Studies of Curcumin by Hydrogen Peroxide in Acetonitrile Solution

Summary. Steady state quenching studies of curcumin, 1,7-bis(4-hydroxy-3-methoxyphenyl)-1,6-heptadiene-3,5-dione, fluorescence by hydrogen peroxide were conducted in acetonitrile solution. A quenching rate constant, k_q, of 1.05×10¹⁰M^–1·s^–1 was obtained with a short fluorescence lifetime of 347ps. The reaction rate constant, which is within the diffusion-limited regime, is activation-controlled. The rate constant of deactivation of the thermally excited curcumin was 1.2 orders of magnitude more nonradiative (2.67×10⁹s^–1) than radiative (2.16×10⁸s^–1). The reaction was exothermic with a G° of –1.97eV and solvent reorganization energy of 1.37eV. These values indicate that the electron transfer reaction is solvent-mediated with electron transfer rate constant, k_ET, of 2.16×10¹⁰s^–1.     

Theoretical Study of Chemical Binding of Noble Gas Atom and Transition Metal Complexes: Ng–NiCO, Ng–NiN2, Ng–CoCO (Ng = He–Xe)

Summary. Ab initio multireference and coupled cluster methods (MR-SDCI(+Q), CASPT2, CCSD(T)) and density functional theory methods (B3LYP, MPWPW91) have been applied to examine geometrical structures and vibrational frequencies of noble gas (Ng) – transition metal compounds, Ng–NiCO, Ng–NiN₂, and Ng–CoCO (Ng = He, Ne, Ar, Kr, Xe). It is shown that the respective compounds can have a larger binding energy than a typical van der Waals interaction energy. The binding mechanism is explained by a partial electron transfer from a noble gas atom to the low-lying 4s and 3d vacant orbitals of the transition metal atom. Theoretical calculations show that the binding of noble gas atom results in a large shift of the bending frequency: 361.1cm^–1 (NiCO) to 403.5cm^–1 (Ar–NiCO); 308.5cm^–1 (NiN₂) to 354.8cm^–1 (Ar–NiN₂); 373.0cm^–1 (CoCO) to 422.6cm^–1 (Ar–CoCO). The corresponding experimental frequencies determined in solid argon are 409.1cm^–1 (NiCO), 357.0cm^–1 (NiN₂), and 424.9cm^–1 (CoCO), which are much closer to the corresponding frequency of Ar–NiCO, Ar–NiN₂, and Ar–CoCO, respectively.     

Electrochemical Behavior of Epinephrine at a Penicillamine Self-Assembled Gold Electrode,and its Analytical Application

The fabrication and electrochemical characteristics of a penicillamine (PCA) self-assembled monolayer modified gold electrode were investigated. The self-assembled electrode shows obvious electrocatalytic activity for the oxidation of epinephrine (EP). In phosphate buffer (pH 7.73), a sensitive oxidation peak was observed at 0.190V with the PCA modified Au electrode. The peak current is proportional to the concentration of EP in the range of 2.0×10^–56.0×10^–4molL^–1 and 5.0×10^–6 2.0×10^–4molL^–1 for cyclic voltammetry (CV) and differential pulse voltammetry (DPV) with the detection limits of 1.8×10^–7 and 1.3×10^–7molL^–1, respectively. The possible reaction mechanism is also discussed. The PCA self-assembled monolayer modified gold electrode is highly stable and can be applied to the determination of EP in practical injection samples. Application is simple, rapid and produces accurate results.     

Electrochemical Study and Selective Determination of Dopamine at a Multi-Wall Carbon Nanotube-Nafion Film Coated Glassy Carbon Electrode

A homogeneous and stable suspension of multi-wall carbon nanotubes (MWNT) was achieved by dispersing MWNT into 0.1% Nafion ethanol solution. A uniform MWNT-Nafion cast film was obtained over a glassy carbon electrode (GCE) via solvent evaporation. The electrochemical behavior of dopamine (DA) was examined, and a reversible two-electron redox reaction was observed. In comparison with the bare GCE and the Nafion-modified GCE, the MWNT-Nafion modified GCE shows obvious electrocatalytic activity towards DA. Moreover, the MWNT-Nafion film coated electrode exhibits excellent selectivity towards DA even in the presence of high concentrations of ascorbic acid (AA) and uric acid (UA). The oxidation peak current was proportional to the concentration of DA over the range of 1×10^–8 to 1×10^–5molL^–1, and a detection limit of 2.5×10^–9molL^–1 was obtained after 2min. of open-circuit accumulation. The dispersion and morphology of MWNT-Nafion film were investigated by transmission electron microscopy (TEM), scanning electron microscopy (SEM) and Fourier transfer (FT) IR spectra.     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Percolation Effects on the Surface of a Polyimide Film Modified with Aqueous Solutions of an Alkali and Acid

A cluster structure of the surface of a polypyromellitimide film was studied by the electron microscopy and ATR IR spectroscopy methods at different steps of consecutive treatment with aqueous solutions of an alkali and acid. The effective size and fractal dimension D of polyamidoacid clusters, as well as the degree _s of the filling of the surface with the latter were calculated from the data of the electron microscopy as a function of the degree of imide group conversion into amidoacid units on the film surface. The _s and D parameters were shown to increase with a rise in : _s = 0.1–0.3 and D = 1.3–1.4 at < _cr and _s 0.6 and D 1.7 at > _cr, where _cr is a critical degree of conversion, which corresponds to the formation of a continuous physical network of polyamidoacid macromolecules or a percolation cluster. In a region close to _cr (at < _cr), the correlation length land the concentration C of the clusters vary according to the laws of the percolation theory for two-dimensional lattices: l (_cr – )^– and C (_cr – ), where = 1.3 ± 0.1 and = 0.67 ± 0.05.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Crystalline Inclusions Formed in C+N+BF2 Coimplanted on Silicon (111)

In the present work, high-doses (10¹⁷–10¹⁸cm^–2) of carbon, nitrogen, and boron (BF₂⁺) ions were coimplanted on silicon (111) substrates at 21, 25 and 77keV, respectively. Two series of samples have been implanted (series A and B) and subsequently annealed. Series A samples have been implanted at room temperature and treated one minute by rapid thermal annealing (RTA) and 3 hours at 1200°C. Series B samples have been implanted at 600°C and subsequently annealed at 1200°C during 3 hours. The annealing in both series has been carried out in N₂ at atmospheric pressures.The structure of the buried layers has been determined by conventional and high resolution transmission electron microscopy (CTEM and HRTEM). Polycrystalline silicon and new crystalline phases are observed by electron diffraction patterns. The polycrystalline silicon inclusions have been confirmed from analysis of HRTEM images.     

Interaction of PM12?nVnO40?(3+n) (M=Mo, W) heteropoly complexes with nitrogen oxide

In aqueous solution, PM_12–nV_nO₄₀ ^–(3+n) (M=Mo,W) hetero-polyanions provide a much faster oxidation of NO than mononuclear VO ₂ ⁺ ions, yielding HNO₂, NO ₃ ^– and reduced HPA.

---

, PM_12–nV_nO₄₀ ^–(3+n) (M=Mo,W) , VO ₂ ⁺ , NO HNO₂ NO ₃ ^– .

     

The kinetic of the oxidation of InSn48

The oxidation of InSn48 has been investigated at partial pressures between 10^-8 Pa and 10⁺⁴ Pa over a temperature range from 22^°C to 250^°C with different analytical methods. The oxide film contains a mixture of several oxides, although indium oxide forms preferentially. Below the melting point a logarithmic growth, and above this, a parabolic growth of the oxide film has been observed. The oxide film formed in air at 250^°C does not become thicker than 50 nm in the first 5 min of oxidation.     

Structural studies and diffusion measurements of water-swollen cellophane by NMR imaging

NMR imaging and spatially resolved diffusometry have been used to study the distribution of water within swollen cellophane and measure its diffusion coefficient. Water concentration and diffusion coefficient were found to be essentially constant across most of the film thickness. However, significantly slower diffusion was indicated for water near the film surface (D=0.5×10^–9m²s^–1) compared with water in the centre of the film (D=0.88×10^–9m²s^–1). This was also reflected in lower T ₂ values at the edge of the film indicating water with more restricted motion. These observations were interpreted in terms of dense surface regions of cellulose (skin) over a more porous interior (core).     

Multi-Syringe Flow Injection System with In-Line Pre-Concentration for the Determination of Total Phenolic Compounds

A multi-syringe flow injection system for the determination of total phenolics based on the 4-aminoantipyrine reaction is proposed. In-line preconcentration using solid-phase extraction was implemented, offering an environmentally friendly alternative to organic solvent extraction performed in the batch procedure and in previously described flow methodologies. Therefore, phenolic compounds were retained in Amberlite XAD4 resin using acidic conditions. The elution was carried out using 0.10molL^–1 NaOH solution, promoting the ionisation of the retained phenolic compounds, and thus their desorption.Since different elution profiles were obtained for several phenol derivatives, the calibration curves were established using the peak area as analytical signal. Moreover, a dynamic calibration range was applied by using a variable sample volume (0.500–6.00mL) and calibration curves based on the mass of phenol retained in the pre-concentration column. A methodology based on a fixed sample volume (24.0mL) was also proposed for determination at concentration levels below 50µgL^–1. A limit of detection of 52ng of phenol (9 or 2µgL^–1) was achieved with a sampling frequency of 10–16h^–1 for the variable volume method and 4h^–1 for the fixed volume method. The application of the proposed methodology to reference material provided results that were within the certified acceptance limits.     

Voltammetric Determination of Bismuth in Water and Nickel Metal Samples with a Sodium Montmorillonite (SWy-2) Modified Carbon Paste Electrode

A simple and reliable electrochemical method for the determination of bismuth in water and nickel metal samples using a sodium montmorillonite (SWy-2) modified carbon paste electrode was described. Due to its strong cation-exchange ability and adsorptive characteristics, SWy-2 significantly enhances the sensitivity of determination for Bi³⁺. Bi³⁺ is firstly preconcentrated and then reduced on the modified electrode surface at –0.50V. After that, reduced bismuth is stripped from the electrode surface during the positive potential sweep of –0.50V to 0.20V, and a well-defined stripping peak at –0.12V appears. The stripping peak current is proportional to the concentration of Bi³⁺ from 4×10^–9molL^–1 to 1×10^–6molL^–1. The detection limit (signal-to-noise=3) is 1×10^–10molL^–1 after 5min. accumulation. The proposed method was successfully applied to the determination of bismuth in water and nickel metal samples.     

Metal Sorption,Solid Phase Extraction and Preconcentration Properties of Two Silica Gel Phases Chemically Modified with 2-Hydroxy-1-Naphthaldehyde

Active silica gel phase (I) was chemically modified to the corresponding amino- (SiNH₂) and chloro- (SiCl) derivatives via silylation reactions. These were used to synthesize two newly modified silica gel phases (II, III) by direct chemical reaction with 2-hydroxynaphthaldehyde (2-HNA). The surface coverage values are 370, 432µmolg^–1 and 320, 355µmolg^–1 for (II) and (III), on the basis of thermal desorption and metal probe testing method, respectively. The metal sorption properties of silica gel phases (II, III) were studied and compared with active silica gel phase (I). The maximum determined metal capacity values were found to be 10–110, 20–290 and 20–370µmolg^–1 for phases I, II and III, respectively. The distribution coefficient values (K_d) were also determined for a series of metal ions, and the results showed that the two new chemically modified phases (II and III) were highly selective for Cu²⁺, Zn²⁺, Cd²⁺, Hg²⁺ and Pb²⁺. The potential applications of silica gel phases (II, III) as solid phase extractors for the same five metal ions spiked in drinking tap water (1.000µgmL^–1) were found to give percentage recovery values in the range of 90.2–96.3±4.1–6.3%, while pre-concentration of the same five metal ions spiked in drinking tap water (50.0ngmL^–1) was successfully accomplished with a percentage recovery range of 92.6–95.8±4.8–5.7%.Received December 16, 2002; accepted May 14, 2003 published online September 1, 2003