Spontaneous polymerization of the nitroethylene–isobutyl vinyl ether system

Initiation and propagation mechanisms of the spontaneous polymerization of the system nitroethylene–isobutyl vinyl ether were studied. An equimolar mixture of these two monomers gives white precipitates below room temperature, though they react explosively to give viscous products at higher temperature. The precipitate was found to be composed of a polynitroethylene and a cycloadduct of these two monomers. The isolated cycloadduct product is so reactive that it not only polymerizes itself spontaneously but also initiates the polymerization of nitroethylene. The polymerization of the cycloadduct was revealed to proceed without termination to produce an alternate copolymer of these two monomers. These results indicate that the explosive spontaneous polymerization of this system consists of three elementary reaction processes; (1) cycloaddition reaction between two monomers, (2) anionic polymerization of nitroethylene induced by the cycloadduct, and (3) the living ring-opening polymerization of the cyclo-adduct.     

Radical addition‐coupling polymerization with various nitroso compounds

Four nitroso esters were prepared by oxidation of 4,4‐dimethyl dihydro‐1,3‐oxazine or 4,4‐dimethyl‐2‐oxazoline with two equiv of m‐chloroperoxybenzoic acid. All of them can be applied in radical addition‐coupling polymerization to produce periodic polymer together with introduction of ester group at side chain. Compared with 2‐methyl‐2‐nitrosopropane, 2‐nitroso‐2‐methyl‐4‐acetoxypentane and 2‐methyl‐2‐nitrosopropyl hexanoate present good stability at high temperature up to 70 °C and can result polymer with high molecular weight. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 810–815     

Radical polymerization of the quinone derived from monoethanolamine vinyl ether and chloranil

Radical polymerization of the quinone derived from monoethanolamine vinyl ether and 2,3,5,6-tetrachloro-1,4-benzoquinone (chloranil) was studied by classical polarography. The conditions of preparation of the redox polymer were optimized. The kinetic characteristics of the process were calculated.Translated from Zhurnal Prikladnoi Khimii, Vol. 77, No. 8, 2004, pp. 1389–1391.Original Russian Text Copyright © 2004 by Ergozhin, Mukhitdinova, Shoinbekova, Nikitina, Zhunusova.     

Star‐polymer synthesis via radical reversible addition–fragmentation chain‐transfer polymerization

Polystyrene stars were synthesized by reversible addition–fragmentation chain‐transfer (RAFT) polymerization using hexakis(thiobenzoylthiomethyl)benzene ( I ) as a hexafunctional RAFT agent at 80, 100, and 120 °C. The polymerizations conformed to pseudo‐first‐order kinetic behavior. The molecular weight distributions displayed characteristics consistent with a living radical process. A number of salient features were observed in the molecular weight distributions with the star distribution accompanied by a linear polymer‐chain distribution and shoulders on the distributions that can be attributed to radical–radical‐termination events. The evidence suggests that high temperatures are required to activate all the RAFT active sites on I , and a hypothesis proposes that there is significant steric hindrance in the initial stages of the RAFT process with I . © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2777–2783, 2001     

Radical polymerization of vinyl thiocyanatoacetate: Participation of group‐transfer mechanism

Vinyl thiocyanatoacetate (VTCA) was synthesized, and its radical polymerization behavior was studied in acetone with dimethyl 2,2′‐azobisisobutyrate (MAIB) as an initiator. The initial polymerization rate (R_p) at 60 °C was expressed by R_p = k[MAIB]^0.6±0.1 [VTCA]^1.0±0.1 where k is a rate constant. The overall activation energy of the polymerization was 112 kJ/mol. The number‐average molecular weights of the resulting poly (VTCA)s (1.4–1.6 × 10⁴) were almost independent of the concentrations of the initiator and monomer, indicating chain transfer to the monomer. The chain‐transfer constant to the monomer was estimated to be 9.6 × 10^?3 at 60 °C. According to the ¹H and ¹³C NMR spectra of poly (VTCA), the radical polymerization of VTCA proceeded through normal vinyl addition and intramolecular transfer of the cyano group. The cyano group transfer became progressively more important with decreasing monomer concentration. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 573–582, 2002; DOI 10.1002/pola.10137     

Reversible addition–fragmentation chain‐transfer polymerization of vinyl monomers with N,N‐dimethyldiselenocarbamates

A new range of selenium‐based reversible addition‐fragmentation chain‐transfer (RAFT) agents is described and tested in the polymerization of styrene, acrylates, vinyl esters, and N‐vinylcaprolactam. The synthesized N,N‐dimethyldiselenocarbamates were poor control agents for styrene polymerization, whereas polyacrylates of controlled molar masses and bearing a diselenocarbamate terminal group could be synthesized. The polymerization of vinyl acetate and vinyl pivalate proceeded in a controlled manner as confirmed by size‐exclusion chromatography, matrix‐assisted laser desorption ionization‐time‐of‐flight mass spectrometry, and ⁷⁷Se NMR analyses. The capability of these RAFT agents to control the polymerization of both more‐activated monomers and less‐activated monomers was exemplified through the synthesis of a poly(t‐butyl acrylate)‐b‐poly(vinyl acetate) diblock copolymer. Considering the very broad range of carbamate groups which can be envisioned, this finding opens numerous perspectives for diselenocarbamate‐mediated RAFT polymerization with its specificities yet to be explored. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4361–4368     

Reversible addition–fragmentation chain transfer mediated radical polymerization of asymmetrical divinyl monomers targeting hyperbranched vinyl polymers

Reversible addition–fragmentation chain transfer (RAFT) mediated radical polymerizations of allyl methacrylate and undecenyl methacrylate, compounds containing two types of vinyl groups with different reactivities, were investigated to provide hyperbranched polymers. The RAFT agent benzyl dithiobenzoate was demonstrated to be an appropriate chain‐transfer agent to inhibit crosslinking and obtain polymers with moderate‐to‐high conversions. The polymerization of allyl methacrylate led to a polymer without branches but with five‐ or six‐membered rings. However, poly(undecenyl methacrylate) showed an indication of branching rather than intramolecular cycles. The hyperbranched structure of poly(undecenyl methacrylate) was confirmed by a combination of ¹H, ¹³C, ¹H–¹H correlation spectroscopy, and distortionless enhancement by polarization transfer 135 NMR spectra. The branching topology of the polymers was controlled by the variation of the reaction temperature, chain‐transfer‐agent concentration, and monomer conversion. The significantly lower inherent viscosities of the resulting polymers, compared with those of linear analogues, demonstrated their compact structure. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 26–40, 2007     

Stereospecific polymerization of isobutyl vinyl ether by AIR3–VCl3·LiCl catalyst. II. Effects of polymerization conditions on polymerization

The effect of polymerization conditions such as aging time of the catalyst, polymerization temperature, polymerization time, monomer concentration, and catalyst concentration on the polymerization of isobutyl vinyl ether was intensively studied by using the VCI₃·LiCl–Al(i-Bu)₃ system at an Al(i-Bu)/VCl₃·LiCl ratio of 6 at which the cationic polymerization by VCl₃·LiCl is sufficiently depressed. About 10 min aging of the catalyst in the presence of monomer yields a fairly stable catalytie system. The optimum polymerization temperature is around 30°C. The conversion increased with increasing monomer concentration, whereas the stereospecificity of polymerization decreased. Unexpectedly, the conversion decreased as total catalyst concentration increased. This phenomenon is explained by considering the deactivation of catalytic sites by the excess of Al(i-Bu)₃. A reasonable mechanism from kinetic considerations is that two molecules of Al(i-Bu)₃ deactivate the catalytic site in an equilibrium reaction. This deactivation is understandable by considering that the coordination of two molecules of Al(i-Bu)₃ will occupy all the coordination positions of vanadium, so that there is no room for coordination of monomer coming to the catalytic site.     

Modeling the reversible addition–fragmentation transfer polymerization process

A kinetic model has been developed for reversible addition–fragmentation transfer (RAFT) polymerization with the method of moments. The model predicts the monomer conversion, number‐average molecular weight, and polydispersity of the molecular weight distribution. It also provides detailed information about the development of various types of chain species during polymerization, including propagating radical chains, adduct radical chains, dormant chains, and three types of dead chains. The effects of the RAFT agent concentration and the rate constants of the initiator decomposition, radical addition, fragmentation, disproportionation, and recombination termination of propagating radicals and cross‐termination between propagating and adduct radicals on the kinetics and polymer chain properties are examined with the model. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1553–1566, 2003     

Polymer coating of graphene oxide via reversible addition–fragmentation chain transfer mediated emulsion polymerization

This work describes a versatile method to encapsulate graphene oxide (GO) with polymers using reversible addition‐fragmentation chain transfer (RAFT) mediated emulsion polymerization. A living low molecular weight anionic macro‐RAFT statistical copolymer of sodium styrene sulfonate, acrylic acid, and butyl acrylate (BA) was synthesized using 2‐{[(butylsulfanyl)carbonothioyl] sulfanyl} propanoic acid as the chain transfer agent. GO was dispersed in water by pretreating the surface with poly(allylamine hydrochloride) (PAH), before being stabilized by the addition of the anionic macro‐RAFT copolymer. PAH was used to facilitate the adsorption of the macro‐RAFT copolymer to the GO surface via electrostatic attraction between opposite charges. The dispersed GO sheets were encapsulated with polymer by the free radical emulsion polymerization of methyl methacrylate and BA under starved fed conditions. The polymer shells encapsulating the GO sheets were formed by the chain extension of the adsorbed living macro‐RAFT copolymer. TEM, SEM, FTIR, and AFM were used to confirm the presence of the polymer layer on the surface of the GO. The thickness of the polymer coating can be adjusted by controlling the amount of monomer fed into the system. Partial polymer coatings of the GO could be achieved by varying the amount of PAH. The encapsulated GO was found to be easily dispersed in both aqueous and organic solvents over a range of polarities. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1413–1421     

Living cationic polymerization of isobutyl propenyl ether as β-substituted vinyl ether

Isobutyl propenyl ether [IBPE; CH₃CH=CH? OCH₂CH(CH₃)₂] was polymerized with a mixture of hydrogen iodide and iodine (HI/I₂ initiator) in n-hexane at ?40°C to yield living polymers with a nearly monodisperse molecular weight distribution (MWD) (M?_w/M?_n ≈ 1.1). The number-average molecular weight (M?_n) of the polymers increased proportionally to IBPE conversion and further increased when a new monomer feed was added to a completely polymerized solution. The M?_n was controlled by the initial concentration of hydrogen iodide if the acid was charged in excess over iodine. In polymerization by iodine alone the M?_n of the polymers obtained in nonpolar solvents (n-hexane and toluene) also increased with conversion, but their MWD was broader (M?_w/M?_n = 1.3–1.4) than in the HI/I₂-initiated systems under similar conditions. The iodine-initiated polymerization in polar CH₂Cl₂ solvent, in contrast, led to nonliving polymers with a broad MWD (M?_n/M?_n = 1.6–1.8) and M?_n, independent of conversion. The living polymerization of IBPE was also compared with that of the corresponding isobutyl vinyl ether, to determine the effect of the β-methyl group in IBPE.     

Hybrid polymerization of iso-butyl vinyl ether

The radiation-induced hybrid polymerization in the presence of the N-alkoxypyridinium salt having relatively stable nonnucleophilic anion (PF₆⁻) has been investigated in the paper. Based on the analysis of experimental data and the GPC spectrum, the onium salts not only oxidize -alkoxyalkyl radicals, produced from IBVE in dichloromethane by irradiation, to the corresponding cations, but also give nonnucleophilic anions PF₆⁻ for the polymerization system. The experimental results clearly demonstrate that free radical and cationic polymerization mechanisms occurred simultaneously in IBVE/EMP⁺PF₆⁻/CH₂Cl₂ systems on irradiation with γ-ray.     

Low-temperature polymerization of isobutyl vinyl ether

Isobutyl vinyl ether has been polymerized under conditions well known to yield isotactic polymer, viz., with boron trifluoride etherate at 78°C. in a nonpolar hydrocarbon diluent. A particular mixed solvent ratio and previous dissolution of catalyst enabled the polymerization to proceed homogeneously at the beginning. By following the temperature rise in an initially thermostatted system, we showed that the progress of the reaction eventually proceeded via a homogeneous phase to a gellike phase. Isotactic polymer is shown to be produced in both steps by a mechanism of slow chain propagation.     

Reversible addition‐fragmentation chain transfer polymerization of vinyl acetate under high pressure

In this work, high molecular weight polyvinyl acetate (PVAc) (M_n,GPC = 123,000 g/mol, M_w/M_n = 1.28) was synthesized by reversible addition‐fragmentation chain transfer polymerization (RAFT) under high pressure (5 kbar), using benzoyl peroxide and N,N‐dimethylaniline as initiator mediated by (S)‐2‐(ethyl propionate)‐(O‐ethyl xanthate) (X1) at 35 °C. Polymerization kinetic study with RAFT agent showed pseudo‐first order kinetics. Additionally, the polymerization rate of VAc under high pressure increased greatly than that under atmospheric pressure. The “living” feature of the resultant PVAc was confirmed by ¹H NMR spectroscopy and chain extension experiments. Well‐defined PVAc with high molecular weight and narrow molecular weight distribution can be obtained relatively fast by using RAFT polymerization at 5 kbar. © 2015 Wiley Periodicals, Inc. J. Polym. Sci. Part A: Polym. Chem. 2015 , 53, 1430–1436     

Radical polymerization behavior of vinyl phenylsufonylacetate

Vinyl phenylsulfonylacetate (VPSA) was prepared by the reaction of vinyl chloroacetate with sodium benzenesulfinate in acetone in the presence of a phase-transfer catalyst. VPSA showed a high radical homopolymerizability similar to vinyl acetate in spite of the fact that VPSA carries a phenyl group. The polymerization of VPSA with 2,2^′-azobisisobutyrate (MAIB) was kinetically investigated in acetone. The overall activation energy of the polymerization was 27.6 kcal/mol. The polymerization rate (R_p) at 50 °C was expressed by R_p=k[MAIB]^0.67[VPSA]^1.1. Poly(VPSA) showed exothermic (27 °C) and endothermic (57 °C) peaks in its DCS curve, corresponding to crystallization and melting. The tacticity of poly(VPSA) was estimated to be rr=29, mr=49, and mm=22.     

Thermoresponsive micelles from well‐defined block copolymers synthesized via reversible addition–fragmentation chain transfer polymerization

Poly(N‐isopropylacrylamide) (PNIPAAm) homopolymers synthesized by reversible addition–fragmentation chain transfer polymerization were used as macro‐chain‐transfer agents to synthesize smart amphiphilic block copolymers with a switchable hydrophilic–hydrophobic block of PNIPAAm and a hydrophilic block of poly(N‐dimethylacrylamide). All polymers were characterized by gel permeation chromatography, ¹H NMR, and differential scanning calorimetry. The reversible micelles formed by the block copolymers of various compositions in aqueous solutions were characterized by ¹H NMR, dynamic light scattering, and tensiometry. Micelles were observed in the aqueous solutions when the temperature was increased to 40 °C because of the collapse of the PNIPAAm structure, which led to a PNIPAAm hydrophobic block. The drug loading capacity was illustrated with the use of the solvatochromic Reichardt's dye and measured by ultraviolet–visible. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3643–3654, 2005     

Stereospecific polymerization of benzyl vinyl ether by BF3·OEt2

Polymerization of benzyl vinyl ether was carried out by BF₃·OEt₂, and the effects of polymerization conditions on the stereoregularity of the polymer were studied by NMR analysis. The polymerization at ?78°C in toluene gave a highly isotactic polymer. The isotacticity of the polymer was independent of the catalyst concentration but increased with a decrease in the initial monomer concentration and decreased slightly on raising the reaction temperature. When the polymerizations were carried out in toluene—nitroethane mixtures, a gradual decrease in the isotacticity and a rapid decrease in the molecular weight of the polymer were observed with increasing nitroethane in the solvent. The molecular weight of the polymer was almost constant, regardless of the catalyst concentration, and increased with increasing initial monomer concentration and decreasing polymerization temperature. When the polymerization was performed in toluene at ?78°C with a small amount of water or benzyl alcohol, a linear relationship was found between the reciprocal DP of the polymer and water or benzylalcohol concentration. The mechanisms of the initiation reaction and the stereoregulation in the polymerization were also discussed.     

Macromolecular design via reversible addition–fragmentation chain transfer (RAFT)/xanthates (MADIX) polymerization

Among the living radical polymerization techniques, reversible addition–fragmentation chain transfer (RAFT) and macromolecular design via the interchange of xanthates (MADIX) polymerizations appear to be the most versatile processes in terms of the reaction conditions, the variety of monomers for which polymerization can be controlled, tolerance to functionalities, and the range of polymeric architectures that can be produced. This review highlights the progress made in RAFT/MADIX polymerization since the first report in 1998. It addresses, in turn, the mechanism and kinetics of the process, examines the various components of the system, including the synthesis paths of the thiocarbonyl‐thio compounds used as chain‐transfer agents, and the conditions of polymerization, and gives an account of the wide range of monomers that have been successfully polymerized to date, as well as the various polymeric architectures that have been produced. In the last section, this review describes the future challenges that the process will face and shows its opening to a wider scientific community as a synthetic tool for the production of functional macromolecules and materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43:5347–5393, 2005     

Controlled radical polymerization of a trialkylsilyl methacrylate by reversible addition–fragmentation chain transfer polymerization

The reversible addition–fragmentation chain transfer (RAFT) polymerization of a hydrolyzable monomer (tert‐butyldimethylsilyl methacrylate) with cumyl dithiobenzoate and 2‐cyanoprop‐2‐yl dithiobenzoate as chain‐transfer agents was studied in toluene solutions at 70 °C. The resulting homopolymers had low polydispersity (polydispersity index < 1.3) up to 96% monomer conversion with molecular weights at high conversions close to the theoretical prediction. The profiles of the number‐average molecular weight versus the conversion revealed controlled polymerization features with chain‐transfer constants expected between 1.0 and 10. A series of poly(tert‐butyldimethylsilyl methacrylate)s were synthesized over the molecular weight range of 1.0 × 10⁴ to 3.0 × 10⁴, as determined by size exclusion chromatography. As strong differences of hydrodynamic volumes in tetrahydrofuran between poly(methyl methacrylate), polystyrene standards, and poly(tert‐butyldimethylsilyl methacrylate) were observed, true molecular weights were obtained from a light scattering detector equipped in a triple‐detector size exclusion chromatograph. The Mark–Houwink–Sakurada parameters for poly(tert‐butyldimethylsilyl methacrylate) were assessed to obtain directly true molecular weight values from size exclusion chromatography with universal calibration. In addition, a RAFT agent efficiency above 94% was confirmed at high conversions by both light scattering detection and ¹H NMR spectroscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5680–5689, 2005