Effect of Epoxidation of Diene Component of SBS Block Copolymer on Morphology and Mechanical Properties

In this work, the polybutadiene (PB) block of an asymmetric lamellae forming polystyrene/polybutadiene based triblock copolymer was epoxidized to different extent in order to study its effect on morphology and mechanical behaviour of the copolymer. The products were analyzed by means of different microscopic techniques, Fourier transform infrared (FTIR) spectroscopy and microhardness measurements. It was found that the microphase separation behavior and hence the mechanical properties of the materials were drastically altered through epoxidation of the diene block of the styrene/diene triblock copolymer. With the increase in the extent of epoxidation the lamellar structure changed to distorted lamellae and then to disordered domains. Consequently, inhomogeneous mechanical performance of the samples was observed at higher degree of chemical modification.     

Synthesis of low polydispersity polybutadiene and polyethylene stars by convergent living anionic polymerization

Star‐shaped polybutadiene stars were synthesized by a convergent coupling of polybutadienyllithium with 4‐(chlorodimethylsilyl)styrene (CDMSS). CDMSS was added slowly and continuously to the living anionic chains until a stoichiometric equivalent was reached. Gel permeation chromatography‐multi‐angle laser light scattering (GPC‐MALLS) was used to determine the molecular weights and molecular weight distribution of the polybutadiene polymers. The number of arms incorporated into the star depended on the molecular weight of the initial chains and the rate of addition of the CDMSS. Low molecular weight polybutadiene arms (M_n = 640 g/mol) resulted in polybutadiene star polymers with an average of 12.6 arms, while higher molecular weight polybutadiene arms (M_n = 16,000 g/mol) resulted in polybutadiene star polymers with an average of 5.3 arms. The polybutadiene star polymers exhibited high 1,4‐polybutadiene microstructure (88.3–93.1%), and narrow molecular weight distributions (M_w/M_n = 1.11–1.20). Polybutadiene stars were subsequently hydrogenated by two methods, heterogeneous catalysis (catalytic hydrogenation using Pd/CaCO₃) or reaction with p‐toluenesulfonhydrazide (TSH), to transform the polybutadiene stars into polyethylene stars. The hydrogenation of the polybutadiene stars was found to be close to quantitative by ¹H NMR and FTIR spectroscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 828–836, 2006     

Styrene-PEG (600) DMA Crosslinked Polymers for Absorption of Oil Derivatives

In this work, styrene (St) based crosslinked polymers were prepared for removal of oil derivatives from aqueous solutions. Polyethylene glycol (600) dimethacrylate (PEG (600) DMA) was used as crosslinker in synthesis of styrene based crosslinked polymers, for the first time. The polymers were characterized by FTIR, SEM, elemental analysis and solvent (toluene, chloroform and fuel-oil) absorption capacities. The effects of different reaction parameters like crosslinker type, diluents amount and the presence of pore forming agent on the absorption properties of polymers were investigated. The polymers synthesized by using PEG (600) DMA have higher solvent absorption capacity than that of synthesized by using conventional crosslinker. Furthermore, the polymers synthesized in the presence of good diluents have higher absorption capacities. The addition of pore forming agent into the reaction medium has also improved the absorption rate of polymers. The absorption capacity of polymers in different solvents is in order of chloroform > toluene > fuel-oil. It was seen that oil derivatives can be removed efficiently from water by the St-PEG (600) DMA polymers.     

Anionic synthesis of polystyrene and polybutadiene heteroarm star polymers

The use of living linking reactions of poly(styryl)lithium with 1,3-bis(1-phenylvinyl)benzene followed by crossover reactions with styrene or butadiene monomers has been used to prepare four-armed heteroarm, star-branched polymers. Bimodal molecular weight distributions have been observed for crossover reactions with both styrene and butadiene. Addition of THF ([THF]/[Li]=14–32) for crossover to styrene and lithium sec-butoxide for crossover to butadiene produces monomodal molecular weight distributions. Symmetrical, four-armed star polystyrenes have been synthesized; properties have been compared with a corresponding polymer prepared via a silicon tetrachloride linking reaction. Heteroarm, star-branched polymers with two polystyrene arms and two polybutadiene arms with high 1,4-microstructure have been prepared.     

Degradation of epoxidized polyenes in the presence of phthalic acid

Viscometry was used to follow the epoxidation of polybutadiene and styrene–butadiene triblock copolymers (SBS) with monoperoxyphthalic acid (MPPA). Long reaction periods lead to an abnormal increase and then drop in reduced viscosity. The increasing viscosity is due to repulsion between oxirane group and its ring-opening product with phthalic acid, while the viscosity drop can be correlated with a decrease of molecular weight. Long-term storage of the epoxidized polyenes in the reaction solution containing phthalic acid, which is the derived product from MPPA, also leads to the dramatic decrease in molecular weights. The occurrence of degradation was confirmed by GPC analysis of molecular weight and molecular weight distribution. Chloroform accelerated the degradation reaction, possibly through the generation of hydrochloric acid. The degraded products were isolated and analyzed by GPC and NMR. A free radical mechanism was proposed for the oxidative degradation of epoxidized polyenes after excessive reaction.     

Peroxide-Initiated crosslinking of styrene-grafted polymers and copolymers of butadiene

Low molecular weight polymers and copolymers of butadiene were grafted with styrene. The graft products were then crosslinked by using dicumyl peroxide as initiator. The optimum peroxide concentration was established (5 phr). Infrared analysis showed that the reactivity of 1,2-vinyl and that of 1,4-trans double bonds in styrene-grafted polybutadiene is similar. Crosslinking of the graft product seems to involve a radical-chain polymerization of double bonds in the polymer. The reaction rate is proportional to the square root of peroxide concentration and to the concentration of polymer double bonds. Activation energy, reaction heat, reaction order, and crosslinking efficiency were also determined from DSC measurements. No relation was found between the activation energy of crosslinking and the molecular weight of backbone polymer or density of grafting. Crosslinking efficiency was to 25–50 crosslinks per molecule of decomposed peroxide. The crosslinking efficiency for grafted butadiene–styrene copolymers is somewhat lower than that for grafted polybutadienes. From thermogravimetric measurements it was found that the crosslinked grafted polymers show lower resistance to thermal degradation than ungrafted polymers.     

Synthesis and characterization of polymeric linseed oil grafted methyl methacrylate or styrene

Syntheses of wholly natural polymeric linseed oil (PLO) containing peroxide groups have been reported. Peroxidation, epoxidation and/or perepoxidation reactions of linseed oil, either under air or under oxygen flow at room temperature, resulted in polymeric peroxides, PLO-air and PLO-ofl, containing 1.3 and 3.5 wt.-% of peroxide, with molecular weights of 2 100 and 3 780 Da, respectively. PLO-air contained cross-linked film up to 46.1 wt.-% after a reaction time of 60 d, associated with a waxy, soluble part (PLO-air-s) that was isolated with chloroform extraction. PLO-ofl was obtained as a waxy, viscous liquid without any cross-linked part at the end of 24 d under visible irradiation and oxygen flow. Polymeric peroxides, PLO-air-s and PLO-ofl initiated the free radical polymerization of both methyl methacrylate (MMA) and styrene (S) to give PMMA-graft-PLO and PS-graft-PLO graft copolymers in high yields with Mw varying from 37 to 470 kDa. The polymers obtained were characterized by FT-IR, (1)H NMR, TGA, DSC and GPC techniques. Cross-linked polymers were also studied by means of swelling measurements. PMMA-graft-PLO graft copolymer film samples were also used in cell-culture studies. Fibroblast cells were well adhered and proliferated on the copolymer film surfaces, which is important in tissue engineering.     

氯固相合成Ti-ZSM-5催化苯乙烯环氧化对映选择性 的研究

用TiCl~4气固相同晶取代法制得的Ti-ZSM-5作催化剂。研究了以H~2O~2为氧化剂氧化苯乙烯生成环氧苯乙烷的对映选择性,发现生成的环氧苯乙烷主要以R构型为主。考察了反应时间,反应温度,催化剂Ti-ZSM-5以及氧化剂[w(H~2O~2)=30%]的用量等反应条件对苯乙烯环氧化反应对映性的影响。结果表明,反应温度是影响环氧化反应对映选择性的重要因素,降低反应温度有利于提高对映选择性(ee),当反应温度≤40℃时,ee值可达100%;而反应时间,催化剂及氧化剂[w(H~2O~2)=30%]用量对环氧化反应的对映选择性几乎没有影响。     

Temperature and concentration effects on polar-modified alkyllithium polymerizations and copolymerizations

Addition of polar modifiers to alkyllithium-initiated homopolymerizations of butadiene causes substantial changes in the microstructure of the polymers produced. These changes are shown to depend not only on the concentration of modifier, but also on the polymerization temperature. The combined effects of modifier concentration and reaction temperature have been considered, and a method is presented for quickly determining the proper conditions for preparation of a polybutadiene of any 1,2-microstructure within a range of 10–80%. It is also shown that in anionic polar-modified copolymerizations of butadiene–styrene, the reaction temperature is again critical. Within a certain concentration range of modifier, the temperature will influence the rate of styrene incorporation or the randomness of styrene units in the resulting copolymers.     

Determination of reactivity ratios for the copolymerization of styrene and styrene–acrylonitrile with polybutadienes

The copolymerization of styrene and styrene–acrylonitrile with polybutadienes of various microstructures was studied and the reactivity ratios determined. It was shown that for the styrene/acrylonitrile/polybutadiene systems the 1,2 structure is twice as reactive as the trans and four times as reactive as the cis. Studies in the temperature range of 50–80°C reveal that the reactivity of the polybutadiene increases as the temperature rises. When styrene is the monomer the reactivity of polybutadiene and the temperature effect is less intense than when styrene–acrylonitrile is used.     

The effect of 4-vinylcyclohexene on the degradation of polystyrene and on the polymerisation of styrene

It has previously been postulated that the inhibition of polystyrene degradation observed in the initial stages of the isothermal degradation of polystyrene-polybutadiene blends is partly due to reaction of polystyryl radicals with 4-vinylcyclohexene (4VCH) evolved from the polybutadiene. This hypothesis has been tested by examining the effect of small amounts of 4VCH on polystyrene degradation and on the free radical polymerisation of styrene. The results provide support for the hypothesis: there is an induction period in the degradation and the polymerisation is retarded. From molecular weight measurements on polymers made in the presence of various amounts of 4VCH, a chain transfer constant in styrene polymerisation at 60°C of 117 × 10^?5 has been calculated.     

用新型茂钛催化剂制备的苯乙烯/丁二烯嵌段共聚物的结构表征

用CpTi(OBz)3/MAO催化体系合成的苯乙烯／丁二烯嵌段共聚合产物经丁酮、甲苯、四氢呋喃、氯仿连续抽提,并用已烷对丁酮的可溶级分进行再抽提;不同级分分别用GPC、^13C -NMR、DSC和WAXD等手段进行分析和表征。发现嵌段共聚物主要存在于氯仿可溶级分中,丁酮可溶级分基本上是无规聚苯乙烯和聚丁二烯组成的混合物（己烷可溶级分为聚丁二烯,不溶级分为无规模聚乙烯）。GPS谱图表明该嵌段共聚反应具有单催化活性中心的聚合特征,^13C-NMR谱图显示该嵌段共聚物分子链由间规聚苯乙链段和聚丁二烯链段组成,WAXD图谱显示嵌段共聚物有较高的结晶度。     

Synthesis of novel diene polymer via friedel–crafts‐type reaction of polybutadiene with aromatic compounds

This study describes a novel and facile synthesis strategy for a styrene‐butadiene rubber (SBR)‐like polymer via Friedel–Crafts‐type reaction between aromatic compounds and polybutadiene using an aluminum chloride as a catalyst. Although gelation was induced by a reaction of a generated carbocation with olefins in other polybutadiene chains in benzene and toluene because of their low electron densities on their rings, anisole with a higher electron density reacted with the polybutadiene carbocation efficiently. The introduction ratio of anisole increased as the reaction proceeded, and the obtained polymer, BRAN polymer, contained 15% anisoles for olefins in the polybutadiene in 4 h at 80 °C as estimated by ¹H NMR analysis. The glass‐transition temperature (T_g) of the BRAN polymer also increased with anisole content (T_g ~?50 °C when anisole contents 20%). The vulcanizate containing the BRAN polymer showed higher mechanical properties compared to samples using other matrix polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 841–847     

Solubilization of oligosaccharides into chloroform by their incorporation into polystyrene as pendant groups

Solubilization of hydrophilic saccharide chains into organic solvents has been attempted by incorporating saccharide-substituted styrene unit into polystyrene main chain. Lactose-, maltopentaose, and amylose-substituted styrene monomers were copolymerized with styrene. Resulting chloroform-soluble copolymers were characterized, and structural formation was investigated. Copolymers of lactose-substituted styrene and maltopentaose-substituted styrene with styrene were dissolved into chloroform. The chloroform-soluble polymers contained about 12 disaccharide lactose chains or 1.7 maltopentaose chains as the pendant groups in one polystyrene molecule. Chloroform-insoluble methyl orange was dissolved into chloroform with the help of chloroform-soluble polystyrene having some saccharide chains. On the other hand, when an amylose-substituted styrene unit was inserted in a polystyrene chain, the resulting polymer became insoluble into chloroform. Amylose polysaccharide of DP_n = ∼24 was not dissolved into chloroform by this method.     

Study on modification of polymers with the aid of the Schmidt reaction

A study of the Schmidt reaction on several polymers with pendant carboxylic and ketone moieties was carried out. Four polymers were used as starting materials: (1) poly(methyl vinyl ketone), (2) poly(acrylic acid), (3) a copolymer of methyl vinyl ketone and acrylic acid, and (4) a copolymer of styrene and acrylic acid. Most reactions were conducted in an acetic acid medium with the exception of one reaction on poly(acrylic acid) which was done in dioxane and another on copolymer of styrene and acrylic acid done in chloroform. It was found that a Schmidt reaction on poly(acrylic acid) in acetic acid solution will lead to intermolecular reactions of the intermediate with the solvent in preference to reactions with neighboring carboxyl groups on the polymer backbone. A tendency of poly(acrylic acid) to form cyclic anhydrides under these reaction conditions interferes with the yield of acetamide units.     

Catalytical oxidation of styrene by molecularly imprinted polymer with phenylacetic acid as template and hemin as co-monomer

This letter used the molecular imprinting technology to build up the microenvironment around co-monomer bemin to mimic the cytochrome P450 catalyzing the epoxidation of styrene.The results showed that the conversion rates of products were obviously enhanced by molecularly imprinted polymers,compared to free hemin solution,using three kinds of oxidants.The used axial ligand in polymers synthesis also improved the total conversion rates.     

负载型金基催化剂Au/Fe(OH)3催化苯乙烯环氧化反应

用共沉淀法制备了Au/Fe(OH)3催化剂, 以叔丁基过氧化氢为氧化剂, 考察焙烧温度和金担载量等对苯乙烯环氧化反应的影响. 结果表明, 催化剂的焙烧温度、金担载量对苯乙烯环氧化反应有较大影响. 在室温下直接合成的质量分数为4.67%的Au/Fe(OH)3催化剂对苯乙烯环氧化反应显示了很好的催化活性, 于80 ℃反应3 h苯乙烯的转化率达到84.1%, 环氧苯乙烷的选择性达到71.5%. 通过X射线粉末衍射(XRD)、X射线光电子能谱(XPS)和Mössbauer分析, 发现催化剂的催化活性与金的价态及铁的化学存在状态有很大关系. 离子态Au3+与载体Fe(OH)3的协同作用对苯乙烯环氧化反应显示出很好的催化活性.     

High performance poly(styrene-b-diene-b-styrene) triblock copolymers from a hydrocarbon-soluble and additive-free dicarbanionic initiator

A new hydrocarbon-soluble (additive-free) dicarbanionic organolithium initiator, obtained by a simple halogen-lithium exchange reaction (Gilman's reaction) from a diarylhalide containing a side C15 alkyl chain, has been designed and used to initiate the anionic polymerization of butadiene and styrene. The dilithiated species formed afford well-defined poly(styrene-b-butadiene-b-styrene) (SBS) triblock copolymers with a high percentage of 1,4-microstructure polybutadiene (91%) and excellent mechanical properties, such as ultimate tensile strength higher than 30 MPa and elongation at a break of 1000%. This represents a breakthrough in the synthesis of SBS polymers, one of the most used thermoplastic elastomers.     

Ring-opening polymerization of 1,5-dioxepan-2-one initiated by a cyclic tin–alkoxide initiator in different solvents

Ring-opening polymerization of 1,5-dioxepan-2-one initiated by 1,1,6,6-tetra-n-butyl-1,6-distanna-2,5,7,10-tetraoxacyclodecane was carried out in chloroform, dichloromethane, or 1,2-dichloroethane. Effects of reaction temperature, solvent, and monomer-to-initiator ratio were investigated. Polymerization kinetics showed a first-order dependence on the monomer for polymerization in chloroform and dichloromethane at 40°C. The kinetic order with respect to the initiator were a first order when dichloromethane was used as the solvent, the order in initiator changed, depending on the initiator concentration when chloroform was used. A maximum in molecular weight was observed at 40°C when chloroform was used as the solvent. The change of solvent did not markedly alter the polymerization rate or the molecular weight of the polymers prepared, as expected from the coordination insertion mechanism. Depolymerization of the polymers formed was observed when the reaction was allowed to continue after complete monomer conversion in chloroform as reaction medium at 40°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3407–3417, 1999     

Block Polymers Derived from Poly(ethylene Oxide) and Carboxyl-Terminated Polybutadiene

The use of preformed poly(ethylene oxide) (PEO) and carboxyl-terminated polybutadiene (CTPB) for the preparation of block polymers is reported. Block polymerization was carried out by esterification and by coupling of equimolar amounts of these polymers with 2,4-toluene diisocyanate (TDI). When esterification was carried out, conversion of the two preformed polymers and block polymer composition varied with reaction temperature, catalyst used, and molecular weight of the PEO. Full conversions were not obtained. Better results were achieved when the preformed polymers were coupled with TDI. Tensile properties and water absorption capability of these block polymers were determined. Hydrogels with high water content up to 82% were obtained.