Electron spin resonance studies on graft copolymerization of gaseous styrene onto preirradiated polypropylene. I. Preirradiation in the presence of oxygen

Graft copolymerization of gaseous styrene was carried out onto polypropylene preirradiated in the presence of oxygen at ?78°C and at room temperature, respectively. The origin of the graft initiation activities of these polymers was investigated by means of electron spin resonance (ESR) of trapped radicals. More grafting was found for the polymers irradiated at ?78°C than for those irradiated at room temperature. The difference of grafting between polymers irradiated at ?78°C and those irradiated at room temperature was not explained by the total amounts of trapped radicals, and it was found that all radicals are not effective in the grafting reaction. ESR measurements showed that there exist two kinds of peroxy radicals, one has more effective ability of abstracting hydrogen atoms from the surrounding polymer chains to form carbon radicals, and another is less effective at the temperature of grafting reaction (40°C). Although the samples irradiated at ?78°C contain the both types of radicals, those irradiated at room temperature do not contain the former type of radicals. It was shown that the carbon radicals produced by such a hydrogen abstraction reaction are actually the effective centers in the grafting reaction of polymers irradiated in the presence of oxygen.     

Functional polymers. XIV. Grafting of 2(2-hydroxy-5-vinylphenyl)2H-benzotriazole onto polymers with aliphatic groups

Successful grafting of 2(2-hydroxy-5-vinylphenyl)2H-benzotriazole onto saturated aliphatic C? H groups of polymers has been accomplished. When the grafting reaction was carried out in chlorobenzene at 150–160°C with di-tertiary butylperoxide as the grafting initiator, grafts as high as 20–30% at grafting efficiencies of 50 and 80% have readily been obtained. It was very important to carry out the grafting reaction in tubes sealed under high vacuum since trace amounts of oxygen cause complete inhibition of the grafting reaction by the phenolic monomer. Grafting reactions were carried out on a variety of different polymers including atactic polypropylene, ethylene/vinyl acetate copolymer, poly(methyl methacrylate), poly(butyl acrylate), and polycarbonate.     

MALDI‐TOF‐MS analysis of living cationic polymerization of vinyl ethers. II. Living nature of growing end and side reactions

Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis revealed that the HCl–vinyl ether adduct/SnCl₄/n‐Bu₄NCl initiating system induced living cationic polymerization of isobutyl vinyl ether in CH₂Cl₂ at ?78 °C, that is, the well‐resolved spectra demonstrated that the produced polymers consist of only one series of polymers carrying one initiator fragment at the α end and one methoxy group originated from quenching with methanol at the ω end. The polymer molecular weight as well as the terminal structure were unchanged even when the reaction mixtures were kept unquenched at ?78 °C for an interval of more than five times longer than the reaction period after complete consumption of monomer, which indicates the long lifetime of the living end even under such starved conditions. In contrast, the polymers obtained at a higher temperature, ?15 °C, showed an additional minor series of polymers formed via proton initiation, originating from adventitious water. Under the starved conditions, other side reactions occurred to generate minor series of polymers with an aldehyde ω end or a diisobutyl acetal ω end. Rather surprisingly, however, unsaturated C?C end groups were not detected, which means the absence of β‐proton elimination under these conditions. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1249–1257, 2001     

Phthalocyanine polymers. IV. Novel type of thermally stable polyimides derived from metal phthalocyanine tetramines and benzophenone tetracarboxylic dianhydride

Poly(metal phthalocyanine)imides of copper, cobalt, nickel, and zinc were synthesized by the reaction of metal phthalocyanino tetramines with benzophenone tetracarboxylic dianhydride. These polymers were characterized by elemental analyses and IR, TGA, and inherent viscosity studies. Noteworthy features of these phthalocyanine polymers are their remarkable thermal and thermooxidative stabilities with char yields at 800°C that range from 78 to 83% in a nitrogen atmosphere. The relative thermal stabilities of these polymers have been evaluated by activation energy measurements.     

Distribution analysis of epoxy groups in polymers by derivatization-electron probe X-ray microanalysis.

An analytical method, referred to as "derivatization-electron probe X-ray micro-analysis (XMA)", has been developed to determine the distribution of a small amount of the functional groups in a polymer. The suitable conditions for the derivatization reaction with epoxy groups, which contribute to the hardening reactions of polymers, were investigated. It was found that epoxy groups in polymers were derivatized selectively using gas-phase esterification with hydrochloric acid (HCI). The most suitable amount of HCl in a 50 ml vial was 300 microl. After setting a sample in the vessel without directly contacting the reagent, by reacting the reagent and the sample at 25 degrees C for 1 h, the highest reaction yield and selectivity were obtained. By derivatization-XMA using this reaction condition, the measurement of the distribution of epoxy groups in the polymer became feasible. Actual applications to a depth analysis of epoxy groups in the hardened acrylic coating and epoxy resin proved that this method is useful for the characterization of polymers and for the study of the hardening reaction of polymers.     

Thermally reversible polymer linkages. II. Linear addition polymers

The stepwise addition polymerization reactions of bisazlactones [bis(2-oxazolin-5-one)s] and a variety of 4,4′-bisphenols have been studied for the purpose of making thermally reversible linear polymers. Thus polymerization occurs at or near room temperature, while depolymerization yielding the two monomer species occurs at elevated temperatures. The synthesis of oligomers in solution without the use of catalyst occurs for the reaction of bisazlactones with bisphenols containing an electron-withdrawing moiety between the two phenol groups of the bisphenol. These oligomers regenerate the bisphenol and bisazlactone monomers upon heating to 165–200°C for several hours under dry box conditions. In many cases, these reactions follow the same patterns of reactivity observed in model studies. This chemistry may be useful for forming degradable or recyclable polymers, where shortchain prepolymers, or macromonomers, endcapped with azlactone and phenol moieties could be used to form high molecular weight polymers that are thermoreversible. Such a reaction system might also be used for preventing reactions of bisphenols and/or bisazlactones at low temperatures, with the desired reaction initiated by formation of the reactive species at elevated temperatures. Envisioned uses in this case might be thermally triggered crosslinking or polymerization reactions, or temperature controlled drug release. © 1993 John Wiley & Sons, Inc.     

Polyimidazopyrrolones and related polymers. I. Dianhydrides and o-acetamidodiamines

Solutions of polyimidazopyrrolone precursors prepared by reaction of tetraamines and dianhydrides in polar solvents tend to crosslink and gel very easily. Substitution of o-acetamidodiamines for the tetraamines gives stable solutions. A study of cure mechanisms by TGA, infrared, and pyrolysis experiments with polymers and model compounds indicates that the acetylated materials are converted cleanly to imides at 150°C. At temperatures above 350°C, structural changes and further polymerization occur, with little imidazopyrrolone formation. Polymers derived from tetraamines cure by multiple mechanisms but finally yield the imidazopyrrolone structure. The acetylated polymers and copolymers give acceptable laminates but poor films.     

Synthesis and physical properties of poly(aryl ether)s containing diphenylacetylene moieties

Poly(aryl ether)s containing diphenylacetylene moieties in the backbone have been synthesized. When the polymers are heated an exothermic reaction, resulting from reaction of the acetylene units, occurs in the range 380- 434°C and the polymers undergo a cross-linking reaction. Polymers cross-linked at 340°C exhibit Tg increases from 2°C to complete disappearance of the Tg depending on the concentration of the diphenylacetylene group which has been incorporated into the polymer. In most cases films of the cross-linked polymers are still flexible and exhibit Young's moduli in the range 1.2-2.1 GPa at 200°C. The solubility or the amount of swelling of these cross-linked polymers in solvents depends on the mol % of diphenylacetylene groups incorporated in the polymer backbone. Copolymers have also been synthesized.     

Liquid crystalline lonomers. I. Main-chain liquid crystalline polymer containing pendant sulfonate groups

Liquid crystalline polymers containing sodium sulfonate groups pendant to the polymer backbone were synthesized by an interfacial condensation reaction of brilliant yellow, a sulfonate-containing monomer, with 4,4′-dihydroxy-α,α′-dimethyl benzalazine and a 50/50 mixture of sebacoyl and dodecanedioyl dichlorides. Polymers containing up to ca. 4 mol% brilliant yellow were characterized by elemental analysis and ultraviolet spectroscopy. The polymers were thermally stable to about 300°C, and they exhibited a broad nematic mesophase region of 70–100°C. The solution viscosity behavior in chloroform suggested that intramolecular associations of the sulfonate groups occurred at low polymer concentrations and intermolecular associations predominated at higher concentrations.     

Synthesis and properties of polyether ketones

Polyether ketones were prepared by the nucleophilic reaction of dihaloaromatic ketones with aromatic bisphenols (hydroquinone, resorcinol and 4,4-dihydroxybenzophenone) using various solvents in the presence of anhydrous K₂CO₃. Dihaloaromatic ketones (4,4-difluorobenzophenone/4,4-dichlorobenzophenone) were prepared from the reaction of fluorobenzene/chlorobenzene with carbon tetrachloride in the form of AlCl₃. The polymers were characterized by different physico-chemical techniques. Thermogravimetric studies showed that all the polymers were stable upto 500°C with a char yield above 50% at 900°C in N₂ atmosphere. Isothermal degradation at 400°C under air and N₂ atmosphere reveals about 5% weight loss and about 1% weight loss at 75 min respectively. The effect of solvents, reaction temperature and reaction time on molecular weights are discussed. The effect of the annealing time on crystallinity of the polymers is also discussed.     

Polymerization of coordinated monomers. V. Polymerization of methyl methacrylate–Lewis acid complexes

The polymerization of the complex of methyl methacrylate with stannic chloride, aluminum trichloride, or boron trifluoride was carried out in toluene solution at several temperatures in the range of 60° to ?78°C by initiation of α,α′-azobisisobutyronicrile or by irradiation with ultraviolet rays. The tacticities of the resulting polymers were determined by NMR spectroscopy. Both the 1:1 and the 2:1 methyl methacrylate–SnCl₄ complexes gave polymers with similar tacticities at the polymerization temperatures above ?60°C. With decreasing temperature below ?60°C, the isotacticity was more favored for the 2:1 complex, whereas the tacticities did not change for the 1:1 complex. On the ESR spectroscopy of the polymerization solution under the irradiation of ultraviolet rays at ?120°C, the 1:1 SnCl₄ complex gave a quintet, while the 2:1 SnCl₄ complex gave both a quintet and a sextet. The sextet became weaker with increasing temperature and disappeared at ?60°C. This behavior of the sextet corresponds to the change of the tacticities of polymer for the 2:1 SnCl₄ complex. An intra–intercomplex addition was suggested for the polymerization of the 2:1 complex, which took a cis-configuration on the basis of its infrared spectra. The sextet can be ascribed to the radical formed by the intracomplex addition reaction, while the quintet can correspond to that formed by the intercomplex addition reaction. The proportion of the intracomplex reaction was estimated to be about 0.25 at ?75°C, and the calculated value of the probability of isotactic diad addition of the intracomplex reaction was found to be almost unity.     

Rigid-Rod benzobisthiazole polymers with reactive fluorene moieties: Synthesis and characterization

High purity 2,7-fluorenedicarboxylic acid chloride was synthesized in a multistep reaction scheme from 2,7-dibromofluorene. Subsequent polycondensation in polyphosphoric acid of 2,5-diamino-1,4-benzenedithiol dihydrochloride with terephthaloyl chloride and 2,7-fluorenedicarboxylic acid chloride led to rigid-rod benzobisthiazole polymers with reactive fluorene moieties. The proportion of fluorene in the resultant polymers was controlled through reaction stoichiometry. Soluble polymers with intrinsic viscosities as high as 33.7 dL/g (methanesulfonic acid, 30°C) were obtained if the polymerization temperature was not allowed to exceed 165°C. Insoluble, presumably crosslinked polymers were obtained at higher temperature (190–200°C). Thermal characterization of the polymers by differential thermal analysis and thermal gravimetric analysis/mass spectroscopy did not disclose any thermal transition to 450°C. Onset of weight loss in air did not occur until over 550°C.     

Anionic polymerization of acrylates. III. Polymerization of 2-ethylhexyl acrylate initiated by lithium-tert-butoxide

The polymerization of 2-ethylhexyl acrylate (EtHA) initiated with lithium-tert-butoxide (t-BuOLi) in tetrahydrofuran (THF) and in the temperature range between ?60 and 20°C was investigated. The reaction rate is distinctly temperature-dependent and at ?60°C is already very low, similarly to the polymerization of methacrylates. Molecular weights of the polymers thus formed, particularly at higher temperatures, are inversely proportional to conversion of the monomer due to the slow initiation reaction. This is documented by the low consumption of alkoxide even at long reaction times, which also depends on the reaction temperature. At higher temperatures the polymerization stops spontaneously, due to the greater extent of autotermination reactions. The weak initiating efficiency of the alkoxide decreases still more with decreasing concentration of the monomer during the polymerization, as confirmed by the concentration dependence of the reaction rate in toluene at ?20°C. The results suggest a negligible initiating effect of alkoxides in complex bases, particularly at lower polymerization temperatures. © 1992 John Wiley & Sons, Inc.     

Polyaddition reaction of biscarbodiimides. II. Synthesis of polyguanidines by polyaddition reaction of biscarbodiimides with diamines

A series of polyguanidines was prepared by the polyaddition reaction of biscarbodiimides with diamines. The polyaddition reaction was carried out in solution. The polymers thus obtained had intrinsic viscosities up to 0.84 and molecular weights up to 15000. The structure of the polymers was identified by comparison of their infrared spectra with those of model compounds, elementary analysis, and a study of the reaction conditions. Thermogravimetric study indicated that the polyguanidines decomposed over 170°C under nitrogen. The polyguanidines were highly resistant to hydrolytic degradation by strong acid or alkali. The polyguanidines had basic groups and formed stable hydrochloric salts when they were treated with hydrochloric acid.     

Study of radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. VII. Effect of pretreatment temperature of silica gel on styrene–silica gel system

To investigate the reaction mechanism of radiation-induced polymerization of styrene adsorbed on silica gel, the effect of pretreatment temperature of silica gel was studied. Preheating of silica gel was carried out at 200, 500, and 800°C. The number of silanol groups of silica gel surface decreased as preheating temperature increased. The rate of polymerization on the silica gel preheated at 500°C was faster than that at 200°C, but the polymerization rate on the silica gel preheated at 800°C was the lowest. These results suggest that rate of polymerization on the silica gel is affected by the conditions of silica gel surface such as the number of silanol groups and the pore size. At the same monomer conversion, percent grafting decreased as preheating temperature of silica gel increased. The GPC spectra of both graft polymers and homopolymers have two peaks at all preheating temperatures. The monomer conversion of low molecular weight peaks of graft polymers decreased as preheating temperature of silica gel increased. This result suggests that there is a probability that the grafting sites of low molecular weight peaks of graft polymers somehow interact with silanol groups.     

New poly(amide-imide)s syntheses. VIII. Preparation and properties of poly (amide-imide)s derived from 2,3-bis(4-aminophenoxy)naphthalene,trimellitic anhydride,and various aromatic diamines

The new polymer-forming diimide-diacid, 2,3-bis(4-trimellitimidophenoxy) naphthalene (I), was readily obtained by the condensation reaction of 2,3-bis (4-aminophenoxy) naphthalene with trimellitic anhydride. A series of novel aromatic poly (amide-imide)s were prepared by the direct polycondensation of diimide-diacid I with various aromatic diamines using triphenyl phosphite in N-methyl-2-pyrrolidone (NMP)/pyridine solution containing dissolved calcium chloride. The resultant polymers have inherent viscosities in the range of 0.65–1.02 dL/g at 30°C in N, N-dimethylacetamide. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed tensile strength at break up to 86 MPa, elongation to break of 5–9%, and initial moduli up to 2.35 GPa. The wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or p-oxyphenylene group are partially crystalline, and the other polymers are evidenced as amorphous patterns. These polymers show a glass transition in the range of 213–290°C in their differential scanning calorimetry (DSC) traces. The thermal stability of the polymers was evaluated by thermogravimetry analysis, which showed the 10% weight-loss temperatures in the range of 508–565°C in nitrogen and 480–529°C in air atmosphere. © 1994 John Wiley & Sons, Inc.     

Investigation of the epoxide–carboxylic acid reaction in model compound and polymerization reactions

The reaction of epoxide and acid has been studied in the model reaction of bisphenol-A diglycidyl ether and acetic acid with several base catalysts at 60, 95, and 115°C. The results suggest that no greater than 5% side reactions occur. A series of polyhydroxylester polymers were prepared from bisphenol-A diglycidyl ether and adipic acid. The polymers gel rapidly upon heating at 200°C. Terpolymers of bisphenol-A diglycidyl ether, bisphenol-A, and azelaic acid were prepared. These also gel at 200°C when 50 mole-% of the active hydrogen reactant is azelaic acid.     

Radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. VI. Temperature dependence and effects of additives on methyl methacrylate–silica gel system

To elucidate the reaction mechanism of radiation-induced polymerization of methyl methacrylate adsorbed on silica gel, the temperature dependence and effects of acetone and pyridine were investigated. It was found that even at ?78°C the polymerization rate was quite fast. The amounts of high molecular weight GPC peaks of both graft polymers and homopolymers increased with increasing irradiation temperature. The activation energy of the adsorbed state polymerization was low compared with that of bulk polymerization. The low molecular weight peaks of homopolymers decreased with acetone addition but were almost unaffected by pyridine. The low molecular weight peaks of homopolymers were thus polymerized by an anionic mechanism. In the methyl methacrylate–silica gel system both radical and anionic polymerization take place at the same time in formation of graft polymers and homopolymers. A reaction mechanism for the methyl methacrylate–silica gel system was proposed based on the results obtained to date.     

Diels-Alder polymers. III. Polymers containing phenylated phenylene units

The Diels-Alder reaction of biscyclopentadieneones with diacetylenes produces colorless, soluble, phenylated polyphenylenes of high molecular weight (M?_n ? 40,000) in nearly quantitative conversions. The polymers are noncrystalline, form clear films, and are stable in air to 550°C. Under nitrogen, the polymers lost approximately half the phenyl groups attached to the phenylene main chain to give brown-black insoluble polyphenylenes of very low crystallinity.     

Synthesis of photoreactive poly(ether ether ketone)s containing alkyl groups

Poly(ether ether ketone)s containing alkyl groups were prepared by nucleophilic substitution reaction of alkyl-substituted difluoro diaryl ethers with hydroquinone or by electrophilic substitution reaction of alkyl-substituted diaryl ether with 4,4′-oxydibenzoic acid in PPMA. Polycondensations proceeded smoothly and produced polymers having inherent viscosities up to 0.5-–1.6 dL/g. The polymers were quite soluble in strong acid, dipolar aprotic solvents, and chloroform at room temperature. Thermogravimetry of the polymers showed excellent thermal stability, indicating that 10% weight loses of the polymers were observed in the range above 450°C in nitrogen atmosphere. The glass transition temperatures of the polymers ranged from 128 to 146°C. Furthermore, Polymer 3b functioned as a photosensitive resist of negative type for UV radiation. The resist had a sensitivity of 42 mJ/cm² and a contrast of 2.5, when it was postbaked at 100°C for 10 min, followed by development with THF/acetone at room temperature. © 1996 John Wiley & Sons, Inc.