Random copolyamides of terephthalic acid,p‐phenylenediamine and p‐aminobenzoic acid soluble in N‐methylpyrrolidone/CaCl2

Moderate‐molecular‐weight copolyamides soluble in N‐methylpyrrolidone (NMP) containing dissolved CaCl₂ can be obtained by polycondensation of terephthalic acid (TPA), p‐phenylenediamine (PPD), and p‐aminobenzoic acid (PABA) with triphenyl phosphite/pyridine in NMP. The randomly copolymerized polymers contain more than 40 mol‐% of PABA and are easily soluble in NMP.     

Studies on reactions of the N-phosphonium salts of pyridines. XIV. Wholly aromatic polyamides by the direct polycondensation reaction by using phosphites in the presence of metal salts

Poly-p-benzamide of high molecular weight (η_inh = ～ in H₂SO₄) was obtained by the direct polycondensation reaction of p-aminobenzoic acid (p-ABA) by means of diphenyl and triaryl phosphites in N-methylpyrrolidone (NMP)-pyridine solution containing lithium and calcium chlorides. Molecular weight of polymer varied with the amount of these salts, showing maximum values at the concentration of about 4 wt-% of LiCl or about 8 wt-% of CaCl₂ in the reaction mixture. The reaction temperature at around 80°C gave a polymer of the highest viscosity. The polycondensation reaction was also affected by monomer concentration, solvents, and tertiary amines like pyridine. Similarly, aromatic polyamides with high molecular weight (η_inh values up to 1.34 in H₂SO₄) were prepared from isophthalic acid and aromatic diamines, whereas terephthalic acid gave only low-viscosity polymers.     

High-molecular-weight poly(p-phenyleneterephthalamide) by the direct polycondensation reaction with triphenyl phosphite

Poly(p-phenyleneterephthalamide) of high molecular weight was obtained when the polycondensation of terephthalic acid and p-phenylenediamine was carried out in N-methylpyrrolidone (NMP) that contained dissolved CaCl₂ and LiCl in the presence of pyridine. The molecular weight of the polymer obtained varied with the amount of pyridine relative to the metal salts and with the molar ratios of CaCl₂ to LiCl, the maximum η_inh value of 4.5 being obtained under the conditions Py/(CaCl₂ + LiCl) ≈ 2.5 (mol/mol), CaCl₂/LiCl ≈ 1.2 (mol/mol), and LiCl + CaCl₂ ≈ 4 g. Among the solvents tested, NMP was significantly effective for the reaction. Polycondensations of several combinations of other dicarboxylic acids and diamines were carried out with limited success.     

THE POLYCONDENSATION OF TEREPHTHALOYL CHLORIDE AND p-PHENYLENEDIAMINE HYDROCHLORIDE IN NMP-CaCl_2 SOLVENT SYSTEM

The solution polycondensation of 1,4-phenylenediamine hydrochloride and terephthaloyl chlo-ride with introducing a tertiary amine in NMP-CaCl_2 solvent system were studied in detail.Effect of reactant concentration, the content of CaCl_2, in NMP solvent and the kinds of tertiary amineon inherent viscosity of PPTA polymer have been studied. High molecular weight PPTA withinherent viscosity over 5 was obtained at 0.35Mol/L of reactant concentration in a solvent of NMP-CaCl_2 with the presence of α-picoline.     

Direct polyamidation with thionyl chloride in N-methyl-pyrrolidone

Mechanistic features of the reaction promoted by thionyl chloride and amides such as N-methylpyrrolidone (NMP) were studied. The reaction was effective in the amidation of carboxylic acids, but not effective in the esterification. The amidation was affected by the kind and the amount of amides used, most favorably by two equivalents of NMP with respect to the acid. These amides were assumed to be involved in the intermediate formation, and the reaction was proposed to proceed via Vilsmeier adducts derived from thionyl chloride and the amides, and through activation of a carboxylic acid different from an acyl chloride. The reaction was successfully applied to the direct polycondensation of aromatic dicarboxylic acids and diamines in NMP at 70°C to produce polyamides with high molecular weights. Initial reaction of dicarboxylic acids with the adducts, additive effect of tertiary amines, and polycondensation temperatures were studied in terms of the inherent viscosity of the polymers produced.     

New optically active poly（amide-imide）s derived from N, N′-（4,4-diphthaloyl）-bis-L-leucine and hydantoin derivatives： Synthesis and properties

Six new optically active poly(amide-imide)s(5a-f) were synthesized through the direct polycondensation reaction of N,N'-(4,4'- diphthaloyl)-bis-L-leucine(3) with six hydantoin derivatives(4a-f).Triphenyl phosphite(TPP)/pyridine in the presence of calcium chloride(CaCl_2) and N-methyl-2-pyrrolidone(NMP) were successfully applied for direct polycondensation.The polycondensation reactions produce a series of new poly(amide-imide)s(5a-f) in high yields,and inherent viscosity between 0.42 and 0.55 dL/g.The re...     

Preparation of sulfonyl aromatic polyamides and copolyamides by means of di- or triphenyl phosphite

High molecular-weight aromatic polyamides were obtained by the direct polycondensation reaction of 4,4′-sulfonyldibenzoic acid (SDA) with various aromatic diamines, by means of di- (DPP) or triphenyl phosphite (TPP) in N-methyl-2-pyrrolidone (NMP)-pyridine solution containing metal salts such as LiCl and CaCl₂. The factors affecting the phosphorylation reaction were investigated, in particular for the reaction of SDA and 4,4′-oxydianiline (ODA). For the polymerization by means of TPP, the optimum conditions are: molar ratio of TPP to diacid, higher than 2.3; concentration of metal salts, 8 wt % LiCl or 6 wt % CaCl₂; reaction temperature, 100°C; and monomer concentration, 0.4 mol/L. For the polymerization by means of DPP, the optimum conditions are: molar ratio of DPP to diacid, higher than 3.8; concentration of metal salts of 8 wt % LiCl or 10 wt % CaCl₂; reaction temperature, 110°C; and monomer concentration, 0.4 mol/L. Copolyamides were also prepared from the reaction of ODA with the mixed diacids of SDA and other dicarboxylic acids such as terephthalic acid, isophthalic acid, and 2,6-naphthalene dicarboxylic acid by using TPP and DPP as the condensing agents.     

Fluorine containing poly(amide-imide)s: synthesis and formation of Langmuir-Blodgett monolayers

Soluble fluorine containing poly(amide-imide)s, PAI(1-4), were synthesized from diimide-dicarboxylic acid, 2,2-bis[N-(4-carboxyphenyl)-phthalimide-1,4-yl]hexafluoropropane with various diamines by direct polycondensation in N-methyl-2-pyrrolidone (NMP) containing CaCl₂ and using triphenyl phosphite and pyridine as condensing agents. The polymers were readily soluble in aprotic polar solvents such as NMP, N,N-dimethylacetamide, dimethyl sulfoxide and tetrahydrofuran. Their Langmuir monolayers were studied at the air/water interface. The monolayers were generally stable at the water surface and could be reproducibly transferred onto solid substrates to build up Langmuir-Blodgett (LB) multilayers. The LB mono- and multilayers were characterized by ultra-violet/visible spectroscopy (UV-Vis), surface plasmon resonance, atomic force microscopy.     

Synthesis of a novel naphthalene-based poly(arylene ether-ketone) by polycondensation of 1,5-bis(4-fluorobenzoyl)-2,6-dimethylnaphthalene with bisphenol a

Synthesis of 1,5-bis(4-fluorobenzoyl)-2,6-dimethylnaphthalene ( 1 ), polycondensation of 1 with Bisphenol A, and properties of the obtained polymer were studied. Friedel–Crafts acylation of 2,6-dimethylnaphthalene with 4-fluorobenzoyl chloride in nitrobenzene selectivity afforded 1 in 82% yield. X-ray single crystal structural analysis of 1 confirmed that the dibenzoylation proceeded regioselectively and two methyl groups sterically inhibited the coplanarity of the two aromatic planes. The polycondensation of 1 with Bisphenol A in toluene/N-methyl-2-pyrrolidone (NMP) mixed solvent in the presence of excess potassium carbonate as a condensation reagent was carried out at 180°C for 4 h to quantitatively afford the corresponding poly(arylene ether-ketone) (PEK) 3 with high molecular weight (M?_n～30,000) as a slightly yellow powder. As the reaction time was prolonged, both M?_n and MWD of 3 increased and the solubility of 3 in chloroform clearly decreased. By GPC-LALLS, M?_n of 3 obtained by the polycondensation for 16 h, was 85,000. The PEK 3 with high molecular weight was produced in a quantitative yield in a variety of solvents such as sulfolane. Water formed during the polycondensation hardly affected the yield and molecular weight of 3 , although a small molecular weight decrease took place. To evaluate the special effect of the methyl groups of 3 , polycondensation of 2,6-bis(4-fluorobenzoyl)naphthalene 2 with bisphenol A was carried out for comparison and the corresponding PEK 4 was quantitatively obtained. Whereas 3 was soluble in ordinary organic solvents such as tet-rahydrofuran (THF), chloroform, and NMP at room temperature, 4 was insoluble in most solvents except for strong acids such as conc. sulfonic acid. The polymer 3 showed high glass transition temperature (238°C) and 5% weight loss temperature (457°C). Casting of the polymer from THF solution gave a transparent, tough, flexible, and amorphous film. © 1995 John Wiley & Sons, Inc.     

Phosgene‐free synthesis of polypeptides: Useful synthesis for hydrophobic polypeptides through polycondensation of activated urethane derivatives of α‐amino acids

We report a useful synthetic method of polypeptides using a series of urethane derivative of α‐amino acids (l ‐leucine, l ‐phenylalanine, l ‐valine, l ‐alanine, l ‐isoleucine, l ‐methionine), which are readily synthesized by N‐carbamoylation of tetrabutylammonium salts of α‐amino acids with diphenyl carbonate. Heating these urethane derivatives in N,N‐dimethylacetamide in the presence of n‐butylamine successfully gave the corresponding polypeptides with well‐defined structures through polycondensation with the elimination of phenol and CO₂. The matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry investigation showed that the resulting polypeptides had an n‐BuNH₂‐incorporated initiating end and an amino group at propagating end. These results strongly indicated that primary amines served as an initiator in this polycondensation system. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3726–3731     

Synthesis and characterization of new soluble polyamides derived from 3,3′,5,5′-tetramethyl-2,2-bis[4-(4-carboxyphenoxy)phenyl]propane

A series of new soluble polyamides having isopropylidene and methyl-substituted arylene ether moieties in the polymer chain were prepared by the direct polycondensation of 3,3′,5,5′-tetramethyl-2,2-bis[4-(4-carboxyphenoxy)phenyl]propane and various diamines in N-methyl-2-pyrrolidinone (NMP) containing CaCl₂ using triphenyl phosphite and pyridine as condensing agents. Polymers were produced with moderate to high inherent viscosities of 0.85–1.47 dL g⁻¹ while the weight-average molecular weight and number-average molecular weight were in the range of 86,700–259,000 and 43,300–119,000, respectively. All the polymers were readily dissolved in polar aprotic solvents such as NMP, N,N-dimethylacetamide, and N,N-dimethylformamide, as well as less polar solvents such as m-cresol and pyridine, and even soluble in tetrahydrofuran. These polymers were solution-cast into transparent, flexible and tough films. All of the polymers were amorphous and the polyamide films had a tensile strength range of 82–122 MPa, an elongation at break range of 6–18%, and a tensile modulus range of 2.0–2.8 GPa. These polyamides had glass transition temperatures between 233–260°C and 10% weight loss temperatures in the range of 450–489 and 459–493°C in nitrogen and air atmosphere, respectively. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1997–2003, 1999     

Synthesis and properties of aromatic polyamides derived from 1,6-bis(4-aminophenoxy)naphthalene and aromatic dicarboxylic acids

A new bis(phenoxy)naphthalene-containing diamine, 1,6-bis(4-aminophenoxy)naphthalene, was synthesized in two steps from the condensation of 1,6-dihydroxynaphthalene with p-chloronitrobenzene in the presence of potassium carbonate, giving 1,6-bis(4-nitrophenoxv)naphthalene, followed by hydrazine hydrate/Pd—C reduction. A series of polyamides were synthesized by the direct polycondensation of the diamine with various aromatic dicarboxylic acids in the N-methyl-2-pyrrolidone (NMP) solution containing dissolved metal salts such as CaCl₂ or LiBr using triphenyl phosphite and pyridine as condensing agents. The polymers were obtained in quantitative yield with inherent viscosities of 0.78–3.72 dL/g. Most of the polymers were soluble in aprotic solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), NMP, and they could be solution-cast into transparent, flexible and tough films. The casting films had tensile strength of 102–175 MPa, elongation at break of 8–42%, and tensile modulus of 2.4–3.8 GPa. The polymers derived from rigid dicarboxylic acids such as terephthalic acid and 4,4′-biphenyldicarboxylic acid exhibited some crystalline characteristics. The glass transition temperatures of the polyamides were in the range of 238–337°C, and their 10% weight loss temperatures were above 487°C in nitrogen and above 438°C in air. © 1995 John Wiley & Sons, Inc.     

Synthesis and properties of aromatic polyamides derived from 2,6-bis(4-aminophenoxy)naphthalene and various aromatic dicarboxylic acids

2,6-Bis(4-aminophenoxy)naphthalene (2,6-BAPON) was synthesized in two steps from the condensation of 2,6-dihydroxynaphthalene with p-chloronitrobenzene in the presence of potassium carbonate, giving 2,6-bis(4-nitrophenoxy)naphthalene, followed by hydrazine hydrate/Pd—C reduction. A series of new polyamides were synthesized by the direct polycondensation of 2,6-BAPON with various aromatic dicarboxylic acids in the N-methyl-2-pyrrolidone (NMP) solution containing dissolved metal salts such as CaCl₂ or LiCl using triphenyl phosphite and pyridine as condensing agents. The polymers were obtained in quantitative yields with inherent viscosities of 0.62–2.50 dL/g. Most of the polymers were soluble in aprotic dipolar solvents such as N,N-dimethylacetamide (DMAc) and NMP, and they could be solution cast into transparent, flexible, and tough films. The casting films had yield strengths of 84–105 MPa, tensile strengths of 68–95 MPa, elongations at break of 8–36%, and tensile moduli of 1.4–2.1 GPa. The glass transition temperatures of the polyamides were in the range 155–225°C, and their 10% weight loss temperatures were above 505°C in nitrogen and above 474°C in air. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2147–2156, 1997     

Reaction of halogenated hydrocarbon solvents with tertiary amines: Spectrophotometric and conductimetric study

Halogenated hydrocarbon solvents, SolvCl, (dichloromethane, chloroform, and 1,2‐dichloroethane) react with various types of tertiary amines, A, such as tri‐n‐buthylamine, tropane derivatives (tropine and atropine) and quinine generating a quaternary ammonium salt, N‐halogenalkylammonium chloride (SolvA⁺Cl^?). Some tertiary amines, as well as secondary and primary amines, cannot react with these solvents. This reaction has been detected and studied by both conductivity and visible spectrophotometry measures—the latter after adding a small quantity of a dye, such as bromocresol green (BCGH₂), bromophenol blue (BPBH₂), or tetrabromophenolphthaleinethyl ester (TBPEH). Both study methods permit the determination of the kinetic parameters, and they are in good agreement. The monoprotic TBPEH is the dye of the simplest mechanism, useful to study kinetics of amines of uncertain behavior as quinine, while BPBH₂ is the best dye for quantitative determinations. Kinetics for this reaction are of first order for both amine, A, and solvent, SolvCl; activation energy, E_a, and frequency factor are also determined. Rate constants increase with the amine basicity and with a reduction in the number of the halogen atoms present in the solvent. This reaction is slow but not negligible and must be considered a side reaction of these universally used solvents. © 2004 Wiley Periodicals, Inc. Int J Chem Kinet 36:500–509, 2004     

Photoresponsive poly(methyl methacrylate)2–(polystyrene)2 miktoarm star copolymer containing an azobenzene moiety at the core

We prepared a novel miktoarm star copolymer with an azobenzene unit at the core via combination of atom transfer radical polymerization (ATRP) and nitroxide‐mediated free radical polymerization (NMP) routes. For this purpose, first, mikto‐functional initiator, 3 , with tertiary bromide (for ATRP) and 2,2,6,6‐tetramethylpiperidin‐1‐yloxy (TEMPO) (for NMP) functionalities and an azobenzene moiety at the core was synthesized. The initiator 3 thus obtained was used in the subsequent living radical polymerization routes such as ATRP of MMA and NMP of St, respectively, to give A₂B₂ type miktoarm star copolymer, (PMMA)₂‐(PSt)₂ with an azobenzene unit at the core with controlled molecular weight and low polydispersity (M_w/M_n < 1.15). The photoresponsive properties of 3 and (PMMA)₂‐(PSt)₂ miktoarm star copolymer were investigated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1396–1403, 2006     

Synthesis of polyamides by a new direct polycondensation reaction using triphenyl phosphite and lithium chloride

Metal salts such as lithium chloride were found to facilitate significantly the reaction of carboxylic acids and amines promoted by triphenyl phosphite, and the reaction was applied successfully to the direct polycondensation reaction of dicarboxylic acids and diamines and of p-aminobenzoic acid. Among metal salts tested, lithium chloride was most effective to the reaction; the chloride was involved catalytically in the reaction, its addition of about twice equivalent to triphenyl phosphite giving the most favorable results. Triphenyl phosphite was most effective, whereas diphenyl phosphite was less effective, and alkyl esters gave no polymers. The reaction was also markedly affected by solvents, the most favorable results being given in N-methylpyrrolidone (NMP). Various polyamides of high molecular weight were obtained in quantitative yield.     

Molecular weight characterization of soluble high performance polyimides. 1. Polymer-solvent-stationary phase interactions in size exclusion chromatography

Soluble, fully cyclized m-amino phenyl acetylene terminated polyimides based on several anhydride/diamine monomers were prepared in N-methylpyrrolidine (NMP) and cyclized by solution imidization to controlled molecular weight. The polyimides and a polyamic acid precursor were successfully analyzed by size exclusion chromatography (SEC) utilizing online parallel coupled refractive index and differential viscometer detectors. The calculated M _nvalues were varied from 3,000 to 20,000 daltons. N-methylpyrrolidone (NMP), tetrahydrofuran (THF), and chloroform served as mobile phases for the cross-linked polystyrene gel packings. Normal retention behavior of the polyimides was observed in chloroform, THF, and NMP containing LiBr, or in NMP stirred over P₂O₅ before use. Values of Mark-Houwink-Sakurada exponents for narrow distribution linear polystyrene indicate that pure NMP and NMP with 0.06 M LiBr are good solvents for polystyrene standards at 60°C. In contrast, SEC behavior of polyimides in pure NMP leads to splitting of the peaks with the major portion observed to pass through the columns at the exclusion limit. In contrast to strong polymeric chain expansion of the polyamic acid in dilute solution, presumably due to a polyelectrolyte effect, no increase of intrinsic viscosity of polyimide samples in pure NMP was observed. This exclusion effect of polyimides analyzed in NMP is discussed in terms of possible ion-exclusion from pores of the stationary phase. Differences in polystyrene calibration in NMP with or without additives and the temperature dependence of calibration curves in these mobile phases is discussed as well. ©1995 John Wiley & Sons, Inc.     

New poly(amide-imide)s syntheses. I. Soluble high-temperature poly(amide-imide)s derived from 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene and various aromatic diamines

Novel aromatic poly(amide-imide)s with high inherent viscosities were prepared by direct polycondensation reaction of 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene ( IV ) and aromatic diamines using triphenyl phosphite in the N-methyl–2-pyrrolidone (NMP)/pyridine solution containing dissolved CaCl₂. The diimide-diacid IV was readily obtained by the condensation reaction of 2,5-bis(4-aminophenyl)-3,4-diphenylthiophene ( III ₁) with trimellitic anhydride. The obtained poly(amide-imide)s showed high thermostability. Their decomposition temperatures at 10% weight loss in nitrogen atmospheres were above 550°C and the anaerobic char yield at 800°C ranged from 48 to 68%. Almost all the poly(amide-imide)s showed high glass transition temperatures above 300°C by differential scanning calorimetry (DSC) measurements. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed obvious yield points in the stress-strain curves and had strength at break up to 74.2 MPa, elongation to break up to 70.1%, and initial modulus up to 4.56 GPa. The factors affecting the reaction of diimide-diacid IV and 4,4′-oxydianiline in view of monomer concentration, reaction temperature, and amount of CaCl₂ were also investigated. © 1992 John Wiley & Sons, Inc.     

Exploring Oxidative NHC-Catalysis as Organocatalytic Polymerization Strategy towards Polyamide Oligomers

The polycondensation of diamines and dialdehydes promoted by an N-heterocyclic carbene (NHC) catalyst in the presence of a quinone oxidant and hexafluoro-2-propanol (HFIP) is herein presented for the synthesis of oligomeric polyamides (PAs), which are obtained with a number-average molecular weight (M_n) in the range of 1.7–3.6 kg mol⁻¹ as determined by NMR analysis. In particular, the utilization of furanic dialdehyde monomers (2,5-diformylfuran, DFF; 5,5’-[oxybis(methylene)]bis[2-furaldehyde], OBFA) to access known and previously unreported biobased PAs is illustrated. The synthesis of higher molecular weight PAs (poly(decamethylene terephthalamide, PA10T, M_n = 62.8 kg mol⁻¹; poly(decamethylene 2,5-furandicarboxylamide, PA10F, M_n = 6.5 kg mol⁻¹) by a two-step polycondensation approach is also described. The thermal properties (TGA and DSC analyses) of the synthesized PAs are reported.     

Effect of polycondensation methods on molecular weight distribution of nylon 610

Polycondensation methods greatly influence the molecular weight distribution of poly(hexamethylene sebacamide) (nylon 610) as determined by gel permeation chromatography (GPC). The ratio of weight average molecular weight to number average molecular weight (M_w/M_n) was used as a measure for estimating the molecular weight distribution. The M_w/M_n ratios of nylon 610 obtained from melt, solid phase, and high temperature polycondensation methods were 2 to 3.5, which were expected values for the most probable distribution. However, those for polymers obtained from the direct polycondensation in the presence of triphenylphosphine, interfacial polycondensation and low temperature polycondensation using an acid chloride varied over a wide range from 3.5 to 8.5. The effect of the kind of organic solvents in the interfacial method on the M_w/M_n ratios was especially large, and the molecular weight distribution could be controlled to some extent by selecting an appropriate solvent.