Synthesis, thermal and magnetic properties of new metal iodate: (LiFe1/3)(IO3)2

This paper reports the detail synthesis of a new kind of metal iodate, anhydrous (LiFe_1/3)(IO₃)₂, from aqueous solutions. The synthesized compound shows spinal morphology and is chemical stable up to 400°C. The iodate shows paramagnetic behavior from room temperature down to 4.2 K. At room temperature, the new compound has a hexagonal structure with the lattice parameters a=5.4632(2) Å, c=5.0895(6) Å, Z=1, space group of P6₃.     

Growth of NaBi(WO4)2 crystal by modified-Bridgman method

NaBi(WO₄)₂ (NBW) crystals have been grown for the first time by modified-Bridgman method. Influences of some factors on the crystal growth process are discussed. X-ray powder diffraction experiments show that the unit cell parameters of NBW crystal are a=b=0.5284 nm, c=1.1517 nm, and V=0.3215 nm³. The differential thermal analysis shows that the NBW crystal melts at 923°C.     

Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

The growth and spectroscopic characteristics of Ca3Y2(BO3)4:Er laser crystal

The Ca₃Y₂(BO₃)₄:Er³⁺ crystal with a size up to 20 mm×30 mm was grown by the Czochralski method. The absorption spectrum was measured and its absorption peaks were assigned to the corresponding transitions between the Er³⁺ energy levels. A broad emission spectrum from 1429.4 to 1662.8 nm was exhibited from 530 nm wavelength pumping. This crystal is promising as a tunable infrared laser crystal.     

Growth and spectral properties of Nd:LaVO4 crystal

This paper reports the growth and spectral properties of 3.5 at% Nd³⁺:LaVO₄ crystal with diameter of 20×15 mm² which has been grown by the Czochralski method. The spectral parameters were calculated based on Judd–Ofelt theory. The intensity parameters Ω_λ are: Ω₂=2.102×10⁻²⁰ cm², Ω₄=3.871×10⁻²⁰ cm², Ω₆=3.235×10⁻²⁰ cm². The radiative lifetime τ_r is 209 μs and calculated fluorescence branch ratios are: β₁(0.88μm)=45.2, β₂(1.06μm)=46.7, β₃(1.34μm)=8.1. The measured fluorescence lifetime τ_f is 137 μm and the quantum efficiency η is 65.6%. The absorption band at 808 nm wavelength has an FWHM of 20 nm. The absorption and emission cross sections are 3×10⁻²⁰ and 6.13×10⁻²⁰ cm², respectively.     

NaY(WO4)2:Sm3+粉末的制备及荧光性能

以柠檬酸三钠为结合剂,采用水热法结合高温烧结两步法制备了一系列NaY_1-x(WO₄)₂:xSm³⁺(x=0、0.005、0.010、0.015、0.020、0.025、0.030)粉末。通过X射线衍射(XRD)、扫描电镜(SEM)、红外光谱(FT-IR)和荧光性能(PL)对粉末的相结构、形貌、成分以及发光性能进行了表征。研究结果表明,所合成粉末为NaY(WO₄)₂的纯相,属四方晶系白钨矿结构,其形貌为3D花形。在405 nm的光激发下,NaY(WO₄)₂:Sm³⁺粉末在600 nm处具有最高的荧光强度,对应于Sm³⁺的⁴G_5/2→⁶H_7/2磁偶极跃迁,观察到橙红光发射,且Sm³⁺最佳掺杂摩尔分数为0.015时,粉末显示出最强的荧光发射强度。     

A7MIIRE2(B5O10)3系列紫外非线性光学晶体的研究进展

稀土硼酸盐非线性光学(NLO)材料由于其在激光技术领域的重要应用而备受关注,这主要是因为三价稀土离子如Y³⁺、Sc³⁺、Lu³⁺等可以有效抑制d-d和f-f电子跃迁从而扩宽化合物的透过范围,同时稀土原子与氧原子结合成畸变的多面体可增强材料的非线性光学效应。A₇M^IIRE₂(B₅O₁₀)₃系列(RE为稀土金属,A为碱金属、M为二价金属)化合物是稀土硼酸盐中一类重要的材料,其A、M以及RE位点具备灵活的占据方式,近年来得到了广泛关注。通过化学元素取代法,研究者们对该类化合物的种类进行拓展,目前已经合成出数十种属于该体系的化合物。这些化合物的截止边大多处在紫外甚至是波长小于200 nm的深紫外波段,非线性光学效应为0.4~2.1倍KDP,在紫外以及深紫外波段非线性光学领域中展现出了应用潜力。本文对其研究现状进行了总结,分析了其微观结构与光学性能之间的关系,并指出不同位点组分对材料非线性光学性能的影响,以期对此类化合物今后的发展提供参考。     

Ce3+激活NaSr4(BO3)3荧光粉的格位占据和发光性质研究

采用高温固相法制备了一系列可被紫外光有效激发的Na_1+xSr_4-2x(BO₃)₃∶xCe³⁺荧光粉,并通过X射线衍射、扫描电镜、荧光光谱等测试方法对样品的物相结构、形貌和发光特性进行了表征及分析。X 射线衍射结果显示,Ce³⁺成功掺入到基质NaSr₄(BO₃)₃中;利用高斯峰拟合、多光谱对比等手段,分析并验证了发光中心Ce³⁺占据了NaSr₄(BO₃)₃中Sr²⁺(1)和Sr²⁺(2)两个格位;研究了不同浓度Ce³⁺的掺杂对发光位置和发光强度的影响,随着Ce³⁺掺杂浓度的提高,发射光谱出现红移,发光强度出现增强→减弱→再增强的趋势;将荧光粉的发射光谱与植物光合色素吸收光谱进行对比,发现它不仅可以吸收300~350 nm的紫外光,发射光谱还很好地覆盖了植物光合色素所需的蓝光区吸收波段,证明其在农业生产的转光剂方面有潜在应用价值。     

A simple method to synthesize single-crystalline β-wollastonite nanowires

The single-crystalline β-wollastonite (β-CaSiO₃) nanowires were prepared via a simple hydrothermal method, in the absence of any template or surfactant using cheap and simple inorganic salts as raw materials. Xonotlite [Ca₆(Si₆O₁₇)(OH)₂] nanowires were first obtained after hydrothermal treatment at a lower temperature of 200 °C for 24 h, and after being calcinated at 800 °C for 2 h, xonotlite nanowires completely transformed into β-wollastonite nanowires and the wire-like structure was preserved. The synthesized β-wollastonite nanowires had a diameter of 10–30 nm, and a length up to tens of micrometers, and the single-crystalline monoclinic parawollastonite structured β-wollastonite was identified by XRD with the space group of P2₁/a and cell constants of a=15.42 Å, b=7.325 Å, c=7.069 Å and β=95.38°. A possible growth mechanism of β-wollastonite nanowires was also proposed. The advantages of this method for the nanowire synthesis lie in the high yield, low temperature and mild reaction conditions, which will allow large-scale production at low cost.     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.     

两例相同混合配体构筑的Pb(Ⅱ)/Ag(I)配位聚合物及其荧光性质

多齿配体2-咪唑乙酸(Hima)、4,4'-连吡啶分别与金属盐Pb(NO₃)₂和AgNO₃反应,得到[Pb₂(4,4'-bipy)(ima)(NO₃)₃]_n(1, 3D framework)和[Ag₄(4, 4'-bipy)₃(ima)₂(NO₃)₂(H₂O)₂]_n(2, 3D framework)两个配位聚合物。根据配位聚合物的结构特点,研究了这两个配位聚合物荧光性质等物理化学性能。配位聚合物1在最大激发波长(λ_ex=346 nm)激发下,荧光的最大发射波长为552 nm,配位聚合物2在最大激发波长(λ_ex=369 nm)激发下,荧光的最大发射波长为444 nm。这可能是由于金属和配体之间发生了电荷转移(LMCT)。     

一例含阴离子水簇的钴配合物的合成、结构及理论研究

金属配合物中的水簇研究为研究宏观意义上的水以及与蛋白质分子有关的水分子提供了有效途径。本文合成了一个含有阴离子水簇的带状超分子配合物[Co(2,2-bipy)₂(N₃)₂](N₃)_0.5Cl_0.5·2H₂O(1,2, 2-bipy=2, 2-联吡啶)。单晶结构解析表明,配合物属于三斜晶系,P-1空间群,晶胞参数为:a=0.822 54(7) nm,b=1.175 58(9) nm,c=1.237 06(10) nm,α=91.379 0(10)°,β=92.151 0(10)°,γ=108.119 0(10)°,V=1.135 27(16) nm³,由一个单核[Co(2,2-bipy)₂(N₃)₂]⁺配合物阳离子、两个非配位水分子、0.5个游离的叠氮离子和0.5个氯离子组成,叠氮离子和氯离子位置无序,占有率各为50%。两个客体水分子通过强烈的分子间氢键作用形成了环状水四聚体,且与无序的N^-₃和Cl^-通过氢键作用形成了一个[(H₂O)₄(N₃)Cl]^2- 阴离子水簇。此外,本文基于密度泛函理论(DFT)对配合物[Co(2,2-bipy)₂(N₃)₂]⁺阳离子进行了量子化学计算,分析了其单点能和原子电荷,并计算了中心金属离子的氧化态,计算结果与实验相吻合。     

(La0.95 Eu0.05)F3纳米晶的自牺牲模板法合成及其下转换发光性能研究

利用自牺牲模板法以一种新型稀土层状化合物(La0.95 Eu0.05)2(OH)4SO4·2H2O为模板成功合成出(La0.95 Eu0.05)F3纳米晶并研究其下转换发光性能.采用X射线衍射仪(XRD)、傅里叶红外变换(FT-IR)、场发射扫描电子显微镜(FE-SEM)及荧光光谱仪对合成产物的物相和荧光性能进行表征....     

Thermal and laser properties of Yb:YAl3(BO3)4 crystal

Large optical-quality Yb:YAl₃(BO₃)₄(Yb:YAB) crystals have been grown by the flux method. The thermal properties of Yb:YAB crystal were measured for the first time. The thermal properties of Yb:YAB crystal with different Yb³⁺ ion concentrations are also reported. The results show that the ytterbium concentration influences the properties of Yb:YAB crystal. The specific heat decreases with the increase of Yb³⁺ ion concentrations in the experiment range. Apparently, the thermal expansion coefficient increases along the c-direction with the increase of Yb³⁺ ion concentrations, while it changes slightly along the a-direction. The output laser in 1120–1140 nm ranges has been demonstrated pumped by InGaAs laser. The slope efficiency is 3.8%. The self-frequency-doubling output power of 1 mW is achieved.     

Fabrication of 2D ordered arrays of cobalt silicide nanodots on (0 0 1)Si substrates

Two-dimensional (2D) periodic arrays of Co metal and Co silicide nanodots were successfully fabricated on (0 0 1)Si substrate by using the polystyrene (PS) nanosphere lithography (NSL) technique and thermal annealing. The epitaxial CoSi₂ was found to start growing in samples after annealing at 500 °C. The sizes of the Co silicide nanodots were observed to shrink with annealing temperature. From the analysis of the selected-area electron diffraction (SAED) patterns, the crystallographic relationship between the epitaxial CoSi₂ nanodots and (0 0 1)Si substrates was identified to be [0 0 1]CoSi₂//[0 0 1]Si and (2 0 0)CoSi₂//(4 0 0)Si. By combining the planview and cross-sectional TEM examination, the epitaxial CoSi₂ nanodots formed on (0 0 1)Si were found to be heavily faceted and the shape of the faceted epitaxial CoSi₂ nanodot was identified to be inverse pyramidal. The observed results present the exciting prospect that with appropriate controls, the PS NSL technique promises to offer an effective and economical patterning method for the growth of a variety of large-area periodic arrays of uniform metal and silicide nanostructures on different types of silicon substrates.     

CrO2 (1 0 0) and TiO2 (1 0 0) film heteroepitaxy on a BaF2 (1 1 1)/Si (1 0 0) substrate

Multi-domained heteroepitaxial rutile-phase TiO₂ (1 0 0)-oriented films were grown on Si (1 0 0) substrates by using a 30-nm-thick BaF₂ (1 1 1) buffer layer at the TiO₂–Si interface. The 50 nm TiO₂ films were grown by electron cyclotron resonance oxygen plasma-assisted electron beam evaporation of a titanium source, and the growth temperature was varied from 300 to 600 °C. At an optimal temperature of 500 °C, X-ray diffraction measurements show that rutile phase TiO₂ films are produced. Pole figure analysis indicates that the TiO₂ layer follows the symmetry of the BaF₂ surface mesh, and consists of six (1 0 0)-oriented domains separated by 30° in-plane rotations about the TiO₂ [1 0 0] axis. The in-plane alignment between the TiO₂ and BaF₂ films is oriented as [0 0 1] TiO₂ || BaF₂ or [0 0 1] TiO₂ || BaF₂ . Rocking curve and STM analyses suggest that the TiO₂ films are more finely grained than the BaF₂ film. STM imaging also reveals that the TiO₂ surface has morphological features consistent with the BaF₂ surface mesh symmetry. One of the optimally grown TiO₂ (1 0 0) films was used to template a CrO₂ (1 0 0) film which was grown via chemical vapor deposition. Point contact Andreev reflection measurements indicate that the CrO₂ film was approximately 70% spin polarized.     

Growth and characterization of KY(WO4)2 crystals

Single-crystal growth of KY(WO₄)₂ (KYW) by top-seeded solution growth technique has been investigated. The effects of seed orientation, temperature gradient experienced by the growing crystal and rate of crystallization on crystal quality are reported. The best results are obtained when the growth is seeded along the 0 1 0 direction. Minute deviations from this growth direction are found to be detrimental to crystal perfection. The differential thermal analysis shows that the amount of super-cooling required for dissolution and crystallization of KYW in the flux is only 5° and this promotes an easy formation of tiny crystallites in the solution. Consequently, the crystal rotation and the solution cooling rates are found to have pronounced effects on the growth of KYW crystal.     

Growth and properties of (Pb0.90La0.10)TiO3 thick films prepared by RF magnetron sputtering with a PbO buffer layer

The (Pb_0.90La_0.10)TiO₃ [PLT] thick films (3.0 μm) with a PbO buffer layer were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering method. The PLT thick films comprise five periodicities, the layer thicknesses of (Pb_0.90La_0.10)TiO₃ and PbO in one periodicity are fixed. The PbO buffer layer improves the phase purity and electrical properties of the PLT thick films. The microstructure and electrical properties of the PLT thick films with a PbO buffer layer were studied. The PLT thick films with a PbO buffer layer possess good electrical properties with the remnant polarization (P_r=2.40 μC cm⁻²), coercive field (E_c=18.2 kV cm⁻¹), dielectric constant (ε_r=139) and dielectric loss (tan δ=0.0206) at 1 kHz, and pyroelectric coefficient (9.20×10⁻⁹ C cm⁻² K⁻¹). The result shows the PLT thick film with a PbO buffer layer is a good candidate for pyroelectric detector.     

TiO2-SiO2 monolithic glass formation from sol-gel

This study demonstrates that hydrolysis should be carried out in a step manner in gel synthesis. The key to the increase in the amount of water added is the control of the hydrolysis rate of Ti(OC₄H₉)₄. The hydrolysis of Si(OC₂H₅)₄ can be carried out at about 75°C. The amount of added water (γ_WI), which varied with TiO₂ content (in mol%), was about 64–88% of the total amount of added water. The hydrolysis reaction should be performed at room temperature while Ti(OC₄H₉)₄ is added. The total amount of added water (γ_W) is related to the amount of solvent (R). For example, if TiO₂ is 40mol%, γ_W will vary from 3.2 to 8.0 when R varies from 0.8 to 2.0. The amount of added water was affected by the distribution of solvent in the metal alkoxides. The amount of added water can be increased when R_Si(OC2H5)4 = 1, R_Ti(OC4H9)4 > 1. The rate of rise in temperature of the thermolysis of the dried gel should be less than 10°C per hour, and the heat treatment temperatyre is related to the TiO₂ content (in mol%). Gel glasses without devitrification can only be obtained by thermolysis at 600°C from the gel with no less than 20 mol% TiO₂.     

蓝色荧光粉Sr3LnM(PO4)3F:Eu2+的发光调控

采用高温固相法合成了一系列Eu²⁺激活的Sr₃LnM(PO₄)₃F(Ln=Gd, La, Y; M= Na, K)荧光粉,并通过X射线衍射、扫描电子显微镜、荧光光谱等对样品的物相结构、形貌和发光特性进行了表征及分析。结果表明:成功合成了Sr₃LnM(PO₄)₃F:Eu²⁺荧光粉,样品的粒径为2~10 μm。荧光粉在蓝光区具有强烈的发射,归属为发光中心Eu²⁺的4f⁶5d→4f⁷跃迁。当基质中的碱金属M由Na变成K时,Eu²⁺的发光颜色由淡蓝色变成深蓝色,色纯度大幅提高,有效地调控了Eu²⁺在氟磷灰石Sr₃LnM(PO₄)₃F中的发光,进而发现了一种通过改变第二层配位原子来调控Eu²⁺发光的策略。