Temperature dependence of the surface tension and 0.1 MPa density for 1-Cn-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate with n = 2, 4, and 6

Experimental air–liquid interfacial tension data and density data are presented for three 1-C_n-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphates (FAP), [C_nMIM][(C₂F₅)₃PF₃], with n = 2, 4, and 6, measured at atmospheric pressure in the temperature range from 267 K to 360 K using the Krűss K100MK2 tensiometer. The accuracy of the surface tension measurements was checked by employing the Wilhelmy plate and the du Noüy ring methods in parallel. The combined standard uncertainty associated with the Wilhelmy plate method is estimated to be ±0.1 mN · m⁻¹. The density data were obtained using buoyancy method with an estimated standard uncertainty less then ±0.4 kg · m⁻³ (3 · 10⁻⁴ϱ). The chloride anions decrease the density of the tris(pentafluoroethyl)trifluorophosphates of interest up to six times more effectively than they decrease the density of the imidazolium based tetrafluoroborates. A QSPR analysis of the surface tension of imidazolium based ionic liquids with BF₄, TFA, DCA, FAP, NTf₂, and PF₆ anions indicates, that the FAP ionic liquids fit well into the analyzed group of imidazolium based ionic liquids while those having hexafluorophosphate anion show anomalously high deviations of the experimental surface tension from the values predicted by the QSPR model.     

[H4tren]3/2·(Al6F24)·3H2O,the most condensed fluoride in the Al(OH)3-tren-HFaq.-ethanol system

The most condensed crystalline fluoride that appears in the Al(OH)₃-tren-HF_aq.-ethanol system at 190 °C is found to be [H₄tren]_3/2·(Al₆F₂₄)·3H₂O. The structure is monoclinic, P2₁/c, with a = 21.939(1) Å, b = 6.7180(2) Å, c = 23.329(1) Å, β = 111.324(2)°. _∞(Al₆F₂₄) chains result from the connection of (Al₇F₃₀)⁹⁻ polyanions by opposite AlF₆ octahedra. Hydrogen bonds are established between the _∞(Al₆F₂₄) chains and ordered or disordered [H₄tren]⁴⁺ cations and water molecules.     

The molar enthalpies of solution and vapour pressures of saturated aqueous solutions of some cesium salts

Vapour pressures of water over saturated solutions of cesium chloride, cesium bromide, cesium nitrate, cesium sulfate, cesium formate, and cesium oxalate were determined as a function of temperature. These vapour pressures were used to evaluate the water activities, osmotic coefficients and molar enthalpies of vapourization. Molar enthalpies of solution of cesium chloride, Δ_solH_m(T = 295.73 K; m = 0.0622 mol · kg⁻¹) = (17.83 ± 0.50) kJ · mol⁻¹; cesium bromide, Δ_solH_m(T = 293.99 K; m = 0.0238 mol · kg⁻¹) = (26.91 ± 0.59) kJ · mol⁻¹; cesium nitrate, Δ_solH_m(T = 294.68 K; m = 0.0258 mol · kg⁻¹) = (37.1 ± 2.3) kJ · mol⁻¹; cesium sulfate, Δ_solH_m(T = 296.43 K; m = 0.0284 mol · kg⁻¹) = (16.94 ± 0.43) kJ · mol⁻¹; cesium formate, Δ_solH_m(T = 295.64 K; m = 0.0283 mol · kg⁻¹) = (11.10 ± 0.26) kJ · mol⁻¹ and Δ_solH_m(T = 292.64 K; m = 0.0577 mol · kg⁻¹) = (11.56 ± 0.56) kJ · mol⁻¹; and cesium oxalate, Δ_solH_m(T = 291.34 K; m = 0.0143 mol · kg⁻¹) = (22.07 ± 0.16) kJ · mol⁻¹ were determined calorimetrically. The purity of the chemicals was generally greater than 0.99 mass fraction, except for HCOOCs and (COOCs)₂ where purities were approximately 0.95 and 0.97 mass fraction, respectively. The uncertainties are one standard deviations.     

On the kinetics of thermal electron attachment to perfluoroethers

In this Letter we report the results of the measurements of the rate coefficients for thermal attachment to several perfluoroethers namely perfluorodiglyme (C₆F₁₄O₃), perfluorotriglyme (C₈F₁₈O₄), perfluoropolyether (CF₃–(OCF(CF₃)CF₂)_n–(OCF₂)_m–OCF₃) and perfluorocrownether ((C₂F₄O)₅). Rate coefficients were obtained under thermal conditions in the temperature range 298–378 K. The increase of the rates with temperature follows the Arrhenius law and the activation energies have been obtained from the slope of the ln(k) vs. 1/T. The respective values of the rate coefficients (at 298 K) and activation energies are as follows: 7.7 ± 1.2 × 10^?11 cm³ s^?1 (0.18 ± 0.005 eV), 6.7 ± 2.1 × 10^?11 cm³ s^?1 (0.25 ± 0.004 eV), 2.1 ± 0.2 × 10^?10 cm³ s^?1 (0.16 ± 0.010 eV), 3.1 × 10^?11 cm³ s^?1 (0.27 ± 0.003 eV) for C₆F₁₄O₃, C₈F₁₈O₄, CF₃–(OCF(CF₃)CF₂)_n–(OCF₂)_m–OCF₃ and (C₂F₄O)₅.     

The thermodynamic properties of DyBr3(s) and DyI3(s) from T=5 K to their melting temperatures

Low-temperature calorimetric measurements have been performed on DyBr₃(s) in the temperature range (5.5 to 420 K ) and on DyI₃(s) from T=4 K to T=420 K. The data reveal enhanced heat capacities below T=10 K, consisting of a magnetic and an electronic contribution. From the experimental data on DyBr₃(s) a C⁰_p,m (298.15 K) of (102.2±0.2) J·K⁻¹·mol⁻¹ and a value for {S⁰_m (298.15 K) − S⁰_m (5.5 K)} of (205.5±0.5) J·K⁻¹·mol⁻¹, have been obtained. For DyI₃(s), {S⁰_m (298.15 K) − S⁰_m (4 K)} and C⁰_p,m (298.15 K) have been determined as (226.9±0.5) J·K⁻¹·mol⁻¹ and (103.4±0.2) J·K⁻¹·mol⁻¹, respectively. The values for {S⁰_m (5.5 K) − S⁰_m (0)} for DyBr₃(s) and {S⁰_m (4 K) − S⁰_m (0)} for DyI₃(s) have been calculated, giving S⁰_m (298.15 K)=(212.3±0.9) J·K⁻¹·mol⁻¹ in case of DyBr₃(s) and S⁰_m (298.15 K) =(233.1±0.7) J·K⁻¹·mol⁻¹ for DyI₃(s). The high-temperature enthalpy increment has been measured for DyBr₃(s) in the temperature range (525 to 799 K) and for DyI₃(s) in the temperature range (525 to 627 K). From the results obtained and enthalpies of formation from the literature, thermodynamic functions for DyBr₃(s) and DyI₃(s) have been calculated from T→0 to their melting temperatures at 1151.0 K and 1251.5 K, respectively.     

The vapour pressures of saturated aqueous solutions of magnesium,calcium, nickel and zinc acetates and molar enthalpies of solution of magnesium,calcium, zinc and lead acetates

Vapour pressures of water over saturated solutions of magnesium, calcium, nickel and zinc acetates were determined as a function of temperature. The vapour pressures served to evaluate the water activities, osmotic coefficients and molar enthalpies of vaporization. Molar enthalpies of solution of magnesium acetate tetrahydrate,Δ_solH_m (T =  294.71K ;m =  0.01 mol · kg ^− 1)  =  − (15.65  ±  0.97)kJ · mol ^− 1; calcium acetate,Δ_solH_m (T =  297.18K ;m =  0.01 mol · kg ^− 1)  =  − (28.15  ±  0.28)kJ · mol ^− 1; zinc acetate dihydrate,Δ_solH_m (T =  297.36K ;m =  0.01 mol · kg ^− 1)  =  − (22.49  ±  0.90)kJ · mol ^− 1and lead acetate trihydrate,Δ_solH_m (T =  297.36K ;m =  0.0086 mol · kg ^− 1)  =  (22.46  ±  0.94)kJ · mol ^− 1, were determined calorimetrically.     

Spectroscopic studies and crystal structure of tetrabutylammonium trichlorodimethylstannate(IV): Bu4NSnMe2Cl3

The structure of Bu₄NSnMe₂Cl₃ is found to be monomer, containing a 5-coordinated bipyramidal trigonal tin(IV) center. Crystals belong to the monoclinic space group C2/c, with unit-cell dimensions a = 26.633(4) Å; b = 9.880(2) Å; c = 21.510(2) Å; β = 114.82(2)°; Z = 8; D = 1.287 Mg/m³; R is refined to 0.0537 and R_w = 0.0642 for 3330 reflections (F > 2σ(F)).     

Recent advances on synthesis of potentially non-bioaccumulable fluorinated surfactants

Fluorinated surfactants are exceptional compounds that have found many applications in everyday life. This review focuses on severe issues on the toxicity, persistency and bioaccumulation of these halogenated products, especially perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS), the half-lives of which are several years in human serum. After an introduction on their productions, uses and hazards, this minireview updates non-exhaustive recent strategies of synthesis of original fluorosurfactants that may be potentially non-bioaccumulable. These routes have been devoted on: (i) the preparation of CF₃-X-(CH₂)_n-SO₃Na (with X = O, C₆H₄O or N(CF₃) and n = 8–12), (ii) the use of fluorinated polyethers (achieved either by oligomerization of hexafluoropropylene oxide (HFPO) or by ring opening cationic oligomerization of fluorinated oxetanes; (iii) the telomerization of vinylidene fluoride (VDF) with 1-iodoperfluoralkanes to produce C_nF_2n + 1-(VDF)₂-CH₂CO₂R (n = 2 or 4, R = H or NH₄), (iv) the radical telomerization of 3,3,3-trifluoropropene (TFP) with isoperfluoropropyliodide to prepare (CF₃)₂CF(TFP)_x-R_H, and (v) the radical cotelomerization of VDF and TFP, or their controlled radical copolymerization in the presence of either (CF₃)₂CFI or a fluorinated xanthate. In most cases, the surface tensions versus the surfactant concentrations have been assessed. These above pathways led to various highly fluorinated (but yet not perfluorinated) telomers or cooligomers, the chemical changes of which enabled to obtain original surfactants as novel alternatives to PFOA, ammonium perfluorooctanoate (APFO), or PFOS regarded as the PCBs of the XXIst century.     

Nd6Li(BO3)3O4F2: A novel neodymium oxyborate fluoride containing two-dimensional Nd layers

Crystal of a new neodymium oxyborate fluoride Nd₆Li(BO₃)₃O₄F₂ was grown by the flux method. Its structure, determined by single crystal x-ray diffraction, belongs to the space group C2/c with cell parameters of a = 12.0629(2) Å, b = 6.94650(10) Å, c = 16.0528(3) Å, β = 104.5360(10)°. In the structure, Nd atoms coordinate to oxygen or fluorine atoms to yeild 7 or 8 coordinated Nd(O,F)n polyhedra. Those polyhedra are edge-shared to form a double layer of (Nd₁₂O₂₃F₄)^14? fluorite blocks. The blocks are linked by oxygen atoms of planar BO₃ groups in the c direction into a 3-dimensional network. Another novel element in the structure is that Li coordinates to 6 oxygen atoms from three BO₃ groups forming a propeller like arrangement, and theoretical calculation shows that such arrangement should give 3/4 that of BO₃ contribution to second harmonic effect. The crystal shows deep violet color with typical Nd³⁺ optical absorption and a UV transmission cut-off of 260 nm.     

New three-dimensional (3,4)-net zincophosphites templated by linear diammonium cations: H3N(CH2)5NH3·Zn3(HPO3)4 and β-H3N(CH2)6NH3·Zn3(HPO3)4

The mild-condition syntheses, single-crystal structures and properties of H₃N(CH₂)₅NH₃·Zn₃(HPO₃)₄ and β-H₃N(CH₂)₆NH₃·Zn₃(HPO₃)₄ are reported. Both are constructed from (3,4)-nets of ZnO₄ tetrahedra and HPO₃ pyramids, sharing vertices to result in three-dimensional anionic open-frameworks. In both materials, the organic species interacts with the framework by way of N–H⋯O bonds. Crystal data: H₃N(CH₂)₅NH₃·Zn₃(HPO₃)₄, M_r = 620.22, orthorhombic, Pccn (No. 56), a = 9.5364 (9) Å, b = 21.8015 (19) Å, c = 9.1118 (7) Å, V = 1894.4 (3) Å³, Z = 4, R(F) = 0.044, wR(F²) = 0.111. β-H₃N(CH₂)₆NH₃·Zn₃(HPO₃)₄, M_r = 634.25, monoclinic, P2₁/n (No. 14), a = 8.7627 (1) Å, b = 13.8117 (2) Å, c = 16.6187 (3) Å, β = 92.680 (1)°, V = 2009.12 (5) Å³, Z = 4, R(F) = 0.072, wR(F²) = 0.187.     

Solubilities of l-glutamic acid, 3-nitrobenzoic acid,p-toluic acid,calcium-l-lactate,calcium gluconate,magnesium-dl-aspartate,and magnesium-l-lactate in water

Solubilities of l -glutamic acid, 3-nitrobenzoic acid, p -toluic acid, calcium-l -lactate, calcium gluconate, magnesium- dl -aspartate, and magnesium- l -lactate in water were determined in the temperature range 278 K to 343 K. The apparent molar enthalpies of solution at T =  298.15 K as derived from these solubilities areΔ_solH_m (l -glutamic acid,m_sat =  0.0565 mol · kg ^− 1)  =  30.2 kJ · mol ^− 1,Δ_solH_m (3-nitrobenzoic acid, m =  0.0188 mol · kg ^− 1)  =  28.1 kJ · mol ^− 1, Δ_solH_m( p - toluic acid, m =  0.00267 mol · kg ^− 1)  =  23.9 kJ · mol ^− 1,Δ_solH_m (calcium- l -lactate tetrahydrate,m =  0.2902 mol · kg ^− 1)  =  25.8 kJ · mol ^− 1,Δ_solH_m (calcium gluconate, m =  0.0806 mol · kg ^− 1)  =  22.1 kJ · mol ^− 1, Δ_solH_m(magnesium-dl -aspartate tetrahydrate, m =  0.1469 mol · kg ^− 1)  =  11.5 kJ · mol ^− 1, andΔ_solH_m (magnesium- l -lactate trihydrate,m =  0.3462 mol · kg ^− 1)  =  3.81 kJ · mol ^− 1.     

The standard molar enthalpy of sublimation ofη5-bis-pentamethylcyclopentadienyl iron measured with an electrically calibrated vacuum-drop sublimation microcalorimetric apparatus

A heat-flow Calvet microcalorimeter was adapted for the measurement of sublimation enthalpies by the vacuum-drop method, with samples of masses in the range 1 mg to 5 mg. The electrically calibrated apparatus was tested by determining the enthalpies of sublimation of benzoic acid and ferrocene, at T =  298.15 K. The obtained results, Δ_cr^gH_m^o(C₇H₆O₂)  =  (88.3  ±  0.5)kJ · mol ^− 1and Δ_cr^gH_m^o(C₁₀H₁₀Fe) =  (73.3  ±  0.1)kJ · mol ^− 1, are in excellent agreement with the corresponding values recommended in the literature. Subsequent application of the apparatus to the determination of the enthalpy of sublimation of η⁵-bis-pentamethylcyclopentadyenyl iron, at T =  298.15 K, led to Δ_cr^gH_m^o(C₂₀H₃₀Fe)  =  (96.8  ±  0.6)kJ · mol ^− 1.     

Dissociation behaviour of (tetra-n-butylammonium bromide + tetra-n-butylammonium chloride) mixed semiclathrate hydrate systems

The thermal properties of {tetra-n-butylammonium bromide + tetra-n-butylammonium chloride (TBAB + TBAC)} mixed semiclathrate hydrates prepared from aqueous solutions were investigated by dissociation temperature measurements and differential scanning calorimetry (DSC). The maximum dissociation temperature of the mixed hydrate crystals at 0.1 MPa is 288.5 K for x_TBAB = 0.2 {mole fraction of TBAB to (TBAB + TBAC)}, which is higher than that of the pure hydrates {T = (285.5 and 288.2) K for TBAB and TBAC hydrates, respectively}. In addition, the dissociation enthalpies of the mixed hydrates are higher than those of the pure hydrates {(5.55 ± 0.06) kJ ⋅ mol⁻¹ H₂O for pure TBAB hydrate and (5.30 ± 0.05) kJ ⋅ mol⁻¹ H₂O for pure TBAC hydrate}, with a maximum of (5.95 ± 0.12) kJ ⋅ mol⁻¹ H₂O recorded at approximately x_TBAB = 0.4. It was therefore suggested that the crystal distortion in (TBAB + TBAC) mixed hydrates, caused by replacing water molecules by both bromide and chloride anions, was smaller than that observed for each pure hydrate. Consequently, the hydration numbers in the mixed hydrates were hypothesized to be slightly higher than those of the pure hydrates.     

Absorption and emission spectroscopic characterisation of the LOV2-His domain of phot from Chlamydomonas reinhardtii

The absorption and emission behaviour of flavin mononucleotide (FMN) in the wild-type light, oxygen and voltage sensitive domain LOV2 of the photoreceptor phot from the green alga Chlamydomonas reinhardtii is studied. Actually a LOV2-His protein (LOV2 domain bound at N-terminal to 15 His aminoacids via a Gly aminoacid) expressed in an Escherichia coli strain is investigated. For fresh samples stored in the dark an initial fluorescence quantum yield of ϕ_F = 0.12 ± 0.01 and an effective fluorescence lifetime of τ_F = 2.4 ± 0.1 ns are determined. Blue-light photo-excitation generates an intermediate photoproduct (flavin-C(4a)-cysteinyl adduct with absorption peak at 390 nm) resulting in an intensity-dependent fluorescence quenching. In the aqueous solutions at pH 8 approximately 3.8% of the FMN molecules are not bound to the protein binding pocket, whereas 96.2% are non-covalently bound. Even at high-intensity light excitation at 428 nm a fraction of about 7% of the non-covalently bound FMN remains non-converted to an FMN-Cys adduct because of photo-induced back-relaxation of the adduct to non-covalently bound FMN. Two holo-LOV2-His conformations with different adduct recovery time constants are revealed by spectrally and temporally resolved fluorescence and absorption measurements: A fraction of about 48% forms FMN-Cys adducts with a fast recovery time constant of τ_Ad,f = 19 ± 2 s in the dark, and the rest forms adducts with a slow recovery time constant of τ_F,s = 5.5 ± 1 min. Prolonged blue light irradiation of the flavin-C(4a)-cysteinyl adducts reduces their ability to recover back in the dark to non-covalently bound FMN (photo-induced permanent adduct formation). Numerical simulations of the intensity-dependent absorption depletion reveals a quantum yield of intermediate photo-adduct formation of ϕ_Ad = 0.9 ± 0.1. Simulation of the adduct absorption dynamics gives a quantum yield of photo-induced adduct back-relaxation of ϕ_Ad,b = 0.15 ± 0.01 and a quantum yield of photo-induced permanent adduct formation of ϕ_Ad,p = (2.6 ± 0.5) × 10⁻⁴.     

Thermodynamic properties of Na2Ti6O13 and Na2Ti3O7: electrochemical and calorimetric determination

Standard values of Gibbs free energy, entropy, and enthalpy of Na₂Ti₆O₁₃ and Na₂Ti₃O₇ were determined by evaluating emf-measurements of thermodynamically defined solid state electrochemical cells based on a Na–β″-alumina electrolyte. The central part of the anodic half cell consisted of Na₂CO₃, while two appropriate coexisting phases of the ternary system Na–Ti–O are used as cathodic materials. The cell was placed in an atmosphere containing CO₂ and O₂. By combining the results of emf-measurements in the temperature range of 573⩽T/K⩽1023 and of adiabatic calorimetric measurements of the heat capacities in the low-temperature region 15⩽T/K⩽300, the thermodynamic data were determined for a wide temperature range of 15⩽T/K⩽1100. The standard molar enthalpy of formation and standard molar entropy at T=298.15 K as determined by emf-measurements are Δ_fH_m⁰=(−6277.9±6.5) kJ · mol⁻¹ and S_m⁰=(404.6±5.3) J · mol⁻¹ · K⁻¹ for Na₂Ti₆O₁₃ and Δ_fH_m⁰=(−3459.2±3.8) kJ · mol⁻¹ and S_m⁰=(227.8±3.7) J · mol⁻¹ · K⁻¹ for Na₂Ti₃O₇. The standard molar entropy at T=298.15 K obtained from low-temperature calorimetry is S_m⁰=399.7 J · mol⁻¹ · K⁻¹ and S_m⁰=229.4 J · mol⁻¹ · K⁻¹ for Na₂Ti₆O₁₃ and Na₂Ti₃O₇, respectively. The phase widths with respect to Na₂O content were studied by using a Na₂O-titration technique.     

Synthesis,structure and solid state NMR analysis of a new templated titanium(III/IV) fluorophosphate

The title compound MIL-131 (MIL stands for Material from Institut Lavoisier) was prepared hydrothermally (4 days, 473 K, autogenous pressure) in the presence of an organic base (N((CH₂)₂NH₂)₃). The structure of MIL-131 or Ti^IIITi^IV(OH)F₄(HPO₄)·(PO₄)·(N((CH₂)₂NH₃)₃) has been determined ab initio from X-Ray synchrotron powder diffraction data using simulated annealing methods and was refined in the triclinic space group P-1 (no. 2). MIL-131 exhibits a one-dimensional structure built up from inorganic chains of corner sharing TiO₅(OH) titanium(III) octahedra and PO₄ and HPO₄ phosphate tetrahedra, related to TiO₂F₄ titanium octahedra. Protonated triamine cations are located between the inorganic motifs, and interact strongly with the mineral network through hydrogen bondings both with terminal fluorine atoms and hydroxo or oxo groups. Multinuclear solid state NMR has allowed a clear attribution of the protons, fluoride, and phosphate groups environment within the framework of MIL-131. The large values of chemical shift anisotropy together with the absence of any ¹³C NMR response confirmed the presence of paramagnetic titanium(III) species deduced from the crystal structure. Finally, 2D MAS ¹H-³¹P CP-HETCOR NMR correlation experiment gives some insight on the nature of the intra-framework hydrogen bonding.Crystal data for MIL-131: a = 14.109(1) Å, b = 8.462(3) Å, c = 7.179(1) Å, α = 93.772(1)°, β = 96.566(2)°, γ = 98.004(1)°, V = 840.36(2) ų, z = 2.     

Measurement and correlation of the ( p, ρ, T) relation of sulphur hexafluoride (SF 6). II. Saturated-liquid and saturated-vapour densities and vapour pressures along the entire coexistence curve

Comprehensive and accurate measurements of the saturated-liquid and saturated-vapour densities together with the vapour pressure of pure sulphur hexafluoride were carried out from the temperature T =  224 K (triple-point temperature T_t =  223.555 K) to 0.033 K below the critical temperature ( T_c =  318.723 K). Typical values of the total uncertainties of the measurements are: ⩽ ± 0.01 percent for the vapour pressures,⩽ ± 0.015 percent for the saturated-liquid densities, and⩽ ± 0.016 percent for the saturated-vapour densities. The values for the critical density and the critical pressure ( ρ_c =  742.26 kg · m ^− 3, p_c =  3.7550 MPa) and the isothermal compressibilities in the critical region close to the phase boundary have also been determined from these measurements. Comparisons with experimental results of previous workers are presented. Using the new values of this work, new correlation equations for the vapour pressure, the saturated-liquid density, and the saturated-vapour density have been established.     

(Solid + solute) phase equilibria in aqueous solution. XIII. Thermodynamic properties of hydrozincite and predominance diagrams for (Zn2 + + H2O + CO2)

The thermodynamic properties ofZn₅(OH)₆(CO₃)₂ , hydrozincite, have been determined by performing solubility and d.s.c. measurements. The solubility constant in aqueous NaClO₄media has been measured at temperatures ranging from 288.15 K to 338.15 K at constant ionic strength (I =  1.00 mol · kg ^− 1). Additionally, the dependence of the solubility constant on the ionic strength has been investigated up to I =  3.00 mol · kg ^− 1NaClO₄at T =  298.15 K. The standard molar heat capacity C_{p, m}^ofunction fromT =  318.15 K to T =  418.15 K, as well as the heat of decomposition of hydrozincite, have been obtained from d.s.c. measurements. All experimental results have been simultaneously evaluated by means of the optimization routine of ChemSage yielding an internally consistent set of thermodynamic data (T =  298.15 K): solubility constant log ^* K_{ps 0}⁰ =  (9.0  ±  0.1), standard molar Gibbs energy of formationΔ_fG_m^o {Zn₅(OH)₆(CO₃)₂ }  =  ( − 3164.6  ±  3.0)kJ · mol ^− 1, standard molar enthalpy of formation Δ_fH_m^o{Zn₅(OH)₆(CO₃)₂ }  =  ( − 3584  ±  15)kJ · mol ^− 1, standard molar entropy S_m^o{Zn₅(OH)₆(CO₃)₂ }  =  (436  ±  50)J · mol ^− 1· K ^− 1and C_p,m^o / (J · mol ^− 1· K ^− 1)  =  (119  ±  11)  +  (0.834  ±  0.033)T / K. A three-dimensional predominance diagram is introduced which allows a comprehensive thermodynamic interpretation of phase relations in(Zn^2 +  +  H₂O  +  CO₂) . The axes of this phase diagram correspond to the potential quantities: temperature, partial pressure of carbon dioxide and pH of the aqueous solution. Moreover, it is shown how the stoichiometric composition{n(CO₃) / n(Zn)} of the solid compoundsZnCO₃ and Zn₅(OH)₆(CO₃)₂can be checked by thermodynamically analysing the measured solubility data.     

Isopiestic determination of the osmotic and activity coefficients of Rb 2SO4 (aq) and Cs 2SO 4(aq) at T = (298.15 and 323.15) K,and representation with an extended ion-interaction (Pitzer) model

Isopiestic vapor-pressure measurements were made for Rb ₂SO ₄(aq) from molalitym =  (0.16886 to 1.5679 )mol · kg ^− 1atT =  298.15 K and from m =  (0.32902 to 1.2282 )mol · kg ^− 1at T =  323.15 K, and for Cs ₂SO₄ (aq) from m =  (0.11213 to 3.10815 )mol · kg ^− 1at T =  298.15 K and fromm =  (0.11872 to 3.5095 )mol · kg ^− 1atT =  323.15 K, with NaCl(aq) as the reference standard. Published thermodynamic information for these systems were reviewed and the isopiestic equilibrium molalities and dilution enthalpies were critically assessed and recalculated in a consistent manner. Values of the four parameters of an extended version of Pitzer`s model for osmotic and activity coefficients with an ionic-strength dependent third virial coefficient were evaluated for both systems at both temperatures, as were those of the usual three-parameter Pitzer model. Similarly, parameters of Pitzer`s model for the relative apparent molar enthalpies of dilution were evaluated at T =  298.15 K for both Rb ₂SO ₄(aq) and Cs ₂SO ₄(aq) for the more restricted range of m⩽ 0.101 mol · kg ^− 1. Values of the thermodynamic solubility product K_s(Rb₂ SO ₄, cr, 298.15 K )  =  (0.1392  ±  0.0154) and the CODATA compatible standard molar Gibbs free energy of formationΔ_fG_m^o (Rb ₂SO ₄, cr, 298.15 K )  =  − (1316.91  ±  0.59)kJ · mol ^− 1, standard molar enthalpy of formationΔ_fH_m^o (Rb ₂SO ₄, cr, 298.15 K )  =  − (1435.07  ±  0.60)kJ · mol ^− 1, and standard molar entropy S _m^o(Rb₂ SO ₄, cr, 298.15 K )  =  (199.60  ±  2.88)J · K ^− 1· mol ^− 1were derived. A sample of one of the lots of Rb ₂SO ₄(s) used for part of our isopiestic measurements was analyzed by ion chromatography, and was found to be contaminated with potassium and cesium in amounts that significantly exceeded the claims of the supplier. In contrast, analysis by ion chromatography of a lot of Cs ₂SO ₄(s) used for some of our experiments showed it was highly pure.     

ATP- and redox-induced conformational changes in the activator of the radical enzyme 2-hydroxyisocaproyl-CoA dehydratase

A [4Fe–4S]¹⁺ cluster-containing protein activates 2-hydroxyisocaproyl-CoA dehydratase by an ATP-driven electron transfer. The activator has been proposed to change its conformation by MgATP similarly to nitrogenase Fe-protein. Iron chelation by bathophenanthroline removed the reduced [4Fe–4S]¹⁺ cluster from the activator in an ATP-dependent manner (rate, v = 0.128 ± 0.004 min⁻¹; K_m = 21 ± 1 μM); with ADP no chelation was observed (v < 0.001 min⁻¹). Chelation of the oxidised [4Fe–4S]²⁺ cluster occurred faster with ADP (v = 0.34 ± 0.05 min⁻¹) than with ATP (v = 0.132 ± 0.005 min⁻¹). The data indicate that reduction of the activator and binding of ATP induce conformational changes necessary to transfer the electron to the dehydratase. Interaction of both proteins promotes ATP hydrolysis (K_m = 0.5 ± 0.1 μM).