Uniaxial experimental study of the acoustic emission and deformation behavior of composite rock based on 3D digital image correlation (DIC)

In this paper, uniaxial compression tests were carried out on a series of composite rock specimens with different dip angles, which were made from two types of rock-like material with different strength. The acoustic emission technique was used to monitor the acoustic signal characteristics of composite rock specimens during the entire loading process. At the same time, an optical non-contact 3 D digital image correlation technique was used to study the evolution of axial strain field and the maximal strain field before and after the peak strength at different stress levels during the loading process. The effect of bedding plane inclination on the deformation and strength during uniaxial loading was analyzed. The methods of solving the elastic constants of hard and weak rock were described. The damage evolution process, deformation and failure mechanism, and failure mode during uniaxial loading were fully determined. The experimental results show that the θ = 0?–45?specimens had obvious plastic deformation during loading, and the brittleness of the θ = 60?–90?specimens gradually increased during the loading process. When the anisotropic angle θincreased from 0?to 90?, the peak strength, peak strain,and apparent elastic modulus all decreased initially and then increased. The failure mode of the composite rock specimen during uniaxial loading can be divided into three categories:tensile fracture across the discontinuities(θ = 0?–30?), slid-ing failure along the discontinuities(θ = 45?–75?), and tensile-split along the discontinuities(θ = 90?). The axial strain of the weak and hard rock layers in the composite rock specimen during the loading process was significantly different from that of the θ = 0?–45?specimens and was almost the same as that of the θ = 60?–90?specimens. As for the strain localization highlighted in the maximum principal strain field, the θ = 0?–30?specimens appeared in the rock matrix approximately parallel to the loading direction,while in the θ = 45?–90?specimens it appeared at the hard and weak rock layer interface.     

Effective viscoelastic behavior of particulate polymer composites at finite concentration

Polymeric materials usually present some viscoelastic behavior. To improve the mechanical behavior of these materials, ceramics materials are often filled into the polymeric materials in form of fiber or particle. A micromechanical model was proposed to estimate the overall viscoelastic behavior for particulate polymer composites, especially for high volume concentration of filled particles. The method is based on Laplace transform technique and an elastic model including two-particle interaction. The effective creep compliance and the stress and strain relation at a constant loading rate are analyzed. The results show that the proposed method predicts a significant stiffer response than those based on Mori-Tanaka's method at high volume concentration of particles.     

Numerical analysis of delamination growth for stiffened composite laminated plates

A study of postbuckling and delamination propagation behavior in delaminated stiffened composite plates was presented. A methodology was proposed for simulating the multi-failure responses, such as initial and postbuckling, delamination onset and propagation, etc. A finite element analysis was conducted on the basis of the Mindlin first order shear effect theory and the von-K6rm~n nonlinear deformation assumption. The total energy release rate used as the criteria of delamination growth was estimated with virtual crack closure technique (VCCT). A self-adaptive grid moving technology was adopted to model the delamination growth process. Moreover, the contact effect along delamination front was also considered during the numerical simulation process. By some numerical examples, the influence of distribution and location of stiffener, configuration and size of the delamination, boundary condition and contact effect upon the delamination growth behavior of the stiffened composite plates were investigated. The method and numerical conclusion provided should be of great value to engineers dealing with composite structures.     

Mechanical behaviors and damage constitutive model of ceramics under shock compression

One-stage light gas gun was utilized to study the dynamic mechanical properties of AD90 alumina subjected to the shock loading. Manganin gauges were adopted to obtain the stress-time histories. The velocity interferometer system for any reflector （VISAR） was used to obtain the free surface velocity profile and determine the Hugoniot elastic limit. The Hugoniot curves were fitted with the experimental data. From Hugoniot curves the compressive behaviors of AD90 alumina were found to change typically from elastic to ＂plastic＂. The dynamic mechanical behaviors for alumina under impact loadings were analyzed by using the path line principle of Lagrange analysis, including the nonlinear characteristics, the strain rate dependence, the dispersion and declination of shock wave in the material. A damage model applicable to ceramics subjected to dynamic compressive loading has been developed. The model was based on the damage micromechanics and wing crack nucleation and growth. The effects of parameters of both the micro-cracks nucleation and the initial crack size on the dynamic fracture strength were discussed. The results of the dynamic damage evolution model were compared with the experimental results and a good agreement was found.     

DYNAMIC MECHANICAL BEHAVIOR OF 6061 AL ALLOY AT ELEVATED TEMPERATURES AND DIFFERENT STRAIN RATES

The compressive stress-strain relationships of 6061Al alloy over wide temperatures and strain rates are investigated. The dynamic impact experiments are performed using an improved high temperature split Hopkinson pressure bar apparatus. The experimental results are compared with those obtained by the modified Johnson-Cook constitutive model. It is found that the dynamic mechanical behavior depends sensitively on temperature under relatively low strain rates or on strain rate at relatively high temperatures. The good agreement indicates that it is valid to adopt the parameter identification method and the constitutive model to describe and predict the mechanical response of materials.     

THE USE OF VISCO-ELASTOPLASTIC DAMAGE CONSTITUTIVE MODEL TO SIMULATE NONLINEAR BEHAVIOR OF CONCRETE

A visco-elastoplastic damage constitutive model is proposed for simulating nonlinear behavior of concrete. Based on traditional plastic theory, the irreversible deformation is simulated in effective stress space. In order to reflect different stiffness degradation mechanism of concrete under tensile and compressive loading conditions, both tensile and compressive damage variables are introduced, and then on the basis of energy release rate, the model is firmly derived within the concept of irreversible thermodynamics. The rate-dependent model is considered by introducing viscous regularization into the inelastic strain and damage variable, and combined with an additional elastic condition. Fully implicit backward-Euler algorithm is used to perform constitutive integration. Results of numerical examples using the proposed model agree well with test results for specimens under uniaxial tension and compression, biaxial loading and triaxial loading. Failure processes of single-edge-notched (SEN) beam and double-edge-notched (DEN) specimen are also simulated to further validate the proposed model.     

Combined grain size, strain rate and loading condition effects on mechanical behavior of nanocrystalline Cu under high strain rates

Molecular dynamics simulations of nanocrys-talline Cu with average grain sizes of 3.1 nm, 6.2 nm, 12.4 nm and 18.6 nm under uniaxial strain and stress tension at strain rates of 10 8 s 1 , 10 9 s 1 and 10 10 s 1 are performed to study the combined grain size, strain rate and loading condition effects on mechanical properties. It is found that the strength of nanocrystalline Cu increases as grain size increases regardless of loading condition. Both the strength and ductility of nanocrystalline Cu increase with strain rate except that there is no monotonic relation between the strength and strain rate for specimens under uniaxial strain loading. Moreover, the strength and ductility of specimens under uniaxial strain loading are lower than those under uniaxial stress loading. The nucleation of voids at grain boundaries and their subsequent growth characterize the failure of specimens under uniaxial strain loading, while grain boundary sliding and necking dominate the failure of specimens under uniaxial stress loading. The rate dependent strength is mainly caused by the dynamic wave effect that limits dislocation motion, while combined twinning and slipping mechanism makes the material more ductile at higher strain rates.     

BEHAVIOR OF AIR-ENTRAINED CONCRETE AFTER FREEZE-THAW CYCLES

The experimental study of air-entrained concrete specimens subjected to different cycles of freeze-thaw was completed. The dynamic modulus of elasticity, weight loss, the cubic compressive strength, compressive strength, tensile strength and cleavage strength of air-entrained concrete were measured after 0, 100, 200, 300, 400 cycles of freeze-thaw. The experimental results showed that the dynamic modulus of elasticity and strength decreased as the freeze-thaw was repeated. The influences of freeze-thaw cycles on the mechanical properties, the dynamic modulus of elasticity and weight loss were analyzed according to the experimental results. It can serve as a reference for the maintenance, design and the life prediction of dams, hydraulic structures, offshore structures, concrete roads and bridges in northern cold regions.     

PLASTIC BEHAVIOR AND CONSTITUTIVE MODELING OF ARMOR STEEL OVER WIDE TEMPERATURE AND STRAIN RATE RANGES

Plastic behavior of 603 armor steel is studied at strain rates ranging from 0.001 s-1 to 4500 s-1 , and temperature from 288 K to 873 K. Emphasis is placed on the effects of temperature, strain rate, and plastic strain on flow stress. Based on experimental results, the JC and the KHL models are used to simulate flow stress of this material. By comparing the model prediction and the experimental results of strain rate jump tests, the KHL model is shown to have a better prediction of plastic behavior under complex loading conditions for this material, especially in the dynamic region.     

PROGRESSIVE FRAGMENT MODELING OF FAILURE WAVE IN CERAMICS UNDER PLANAR IMPACT LOADING

Polycrystalline ceramics have heterogeneous meso-structures which result in high singularity in stress distribution. Based on this, a progressive fragment model was proposed which describes the failure wave formation and propagation in shocked ceramics. The governing equation of the failure wave was characterized by inelastic bulk strain with material damage and fracture. And the inelastic bulk strain consists of dilatant strain from nucleation and expansion of microcracks and condensed strain from collapse of original pores. Numerical simulation of the free surface velocity was performed in good agreement with planar impact experiments on 92.93％ aluminas at China Academy of Engineering Physics. And the longitudinal, lateral and shear stress histories upon the arrival of the failure wave were predicted, which present the diminished shear strength and lost spall strength in the failed layer.