TiO2基固体超强酸的制备及光催化性能研究

半导体氧化物TiO2对很多有机污染物吸附较强、催化氧化活性高,因此它在环境污染治理方面扮演极其重要的角色,被广泛用于光催化处理多种有机物,但常规二氧化钛半导体光催化剂较低的量子效率(约4%)使其应用受到一定程度的制约[1]。1979年H ino[2]等首次报道无卤素型SO42-/M xO y固体超强酸体系以来,引起化学工作者极大关注。固体超强酸催化剂如SO42-/TiO2,SbF5/SiO2/TiO2等是一类新型酸催化剂,广泛用于酯化反应、苯衍生物烷基化、烯烃齐聚等。研究发现,基于SO42-改性的TiO2固体超强酸催化剂对于有机物具有较高的光催化氧化活性[3,4],…     

稀土钬及铒钇丙氨酸配合物的量热与热分析研究

合成了两种固态稀土丙氨酸配合物[Ho2(Ala)4(H2O)8]Cl6和[ErY(Ala)4(H2O)8](ClO4)6 (Ala为丙氨酸),用量热和热分析方法研究了这两种配合物的热力学性质.用全自动高精密绝热量热计测定了在78～377 K温区内的低温热容.对于[Ho2(Ala)4(H2O)8]Cl6,在214～255 K温区内发现一固-固相变,其相变温度为235.09 K.对于[ErY(Ala)4(H2O)8](ClO4)6,在99～121 K温区内也发现一固-固相变,其相变温度为115.78 K. [Ho2(Ala)4(H2O)8]Cl6固-固相变焓为3.02 kJ• mol－1,相变熵为12.83 J•K－1•mol－1； [ErY(Ala)4(H2O)8](ClO4)6 固-固相变焓为1.96 kJ•mol－1,相变熵为16.90 J•K－1•mol－1.同时,用TG技术在40～800 ℃温区研究了两配合物的热稳定性.由TG/DTG曲线分析可知, [Ho2(Ala)4(H2O)8]Cl6从80 ℃到479 ℃热分解分两步完成, [ErY(Ala)4(H2O)8](ClO4)6从120 ℃到430 ℃热分解分三步完成.     

钛钨杂多配合物的合成与表征

首次合成了杂多配合物K2[(C2H5)4N]2[TiW5O19].5H2O和K2[(C2H5)4N]2[(TiO2)W5O18].5H2O,配合物通过IR,UV,TG-DTA,摩尔电导,X射线粉末衍射进行了表征.结果表明[TiW5O19]4-具有L indqvist-Aronsson结构.     

钨磷杂多酸盐的合成、表征及催化活性

合成了4个钨磷杂多酸盐——K10H2[P2W15Ti3O62]·2H2O,K12[P2W15(TiO2)3O59]·8H2O,K12[P2W15Zr3O62]·6H2O和K12[P2W15(ZrO2)3O59]·5H2O,用183WNMR,UV,IR,ICP和极谱-循环伏安等测试方法对其性质、结构进行了研究。结果表明它们都是具有Dawson结构的杂多配合物,对顺丁烯二酸的H2O2环氧化反应具有显著的催化活性。     

Fe3+/TiO2光催化降解溴化乙锭的研究

溴化乙锭(Ethidium Bromide,EB),是一种常见的阳离子荧光染料,能与双链核酸发生嵌入作用,使荧光强度显著增强[1],因此被广泛应用于生命科学尤其是分子生物学领域中核酸的定性、定量分析。但EB是一种强烈的诱变剂,具有中度毒性[2],且易逸入空气中,增加了危害性。半导体超细微粒如TiO2[3]、CdS[4]等在紫外光或者可见光光照下产生强烈的氧化作用,能把许多难分解有毒污染物氧化为CO2、H2O等无毒物质。其中TiO2已被广泛用于光催化法处理各种染料以及难分解的污染物[5,6]。当用波长小于或等于388nm的紫外光照射锐钛型TiO2时,可将电子从价…     

超亲水TiO2和TiO2-SiO2表面的动态润湿性

1997年, Fujishima研究组[1]发现TiO2表面经UV光照射能产生较强的亲水性, 同时具有较高的亲油性, 即经UV光照射后的TiO2表面具有超双亲的性质. 这种防雾和自清洁性在工业上应用广泛, 已引起了人们的极大兴趣[2～5]. 进一步的研究发现, 超亲水的TiO2表面在暗处放置会变为疏水表面. 对于这个问题, 除了可以通过UV光照[6]、氩离子或电子束溅射[6]和高温热处理[5]等恢复其超亲水性外, 还可以通过添加摩尔分数为10%～30%的SiO2有效地降低TiO2表面的接触角, 提高UV光诱导的超亲水表面在暗处的稳定性能[3]. 另外, 诱导TiO2的亲水性需要较强的UV线强度(如太阳光), 使它在室内应用受到限制. 为了在室内实现TiO2的自清洁功能, Watanabe等[4]发现在TiO2中添加WO3可使TiO2在室内的照明光下也能实现亲水性转变. 以上这些研究成果为TiO2在工业和生活上的实际应用提供了重要的科学依据. 然而, TiO2的防雾和自清洁功能的实现同时也受其动力学性质的制约.     

纳米α-Fe_2O_3-TiO_2改性海藻酸钠/壳聚糖双极膜制备与表征

在壳聚糖(CS)阴离子交换膜中添加纳米复合半导体材料α-Fe2O3-TiO2,制备了PVA-SA/α-Fe2O3-TiO2-CS双极膜(PVA:聚乙烯醇;SA:海藻酸钠),并用扫描电镜、热重分析、电子万能试验机和接触角测定仪等对其进行了表征。研究结果表明,添加纳米α-Fe2O3-TiO2可提高双极膜的亲水性、热稳定性和机械性能。纳米α-Fe2O3-TiO2复合半导体材料较纳米α-Fe2O3或纳米TiO2单一半导体材料具有更强的光催化双极膜中间界面层水解离能力,在高压汞灯照射下能大大降低双极膜的膜阻抗和膜电阻压降(IR降)。     

空气电极改性TiO2光催化剂的研究

将TiO2/C光催化剂负载在具有合成H2O2性能的空气电极上形成双功能新型复合电极.TiO2/C光催化层的微多孔特性使新型载体保持了高效合成H2O2的优势,J=15mA/cm2时,电流效率达到82%.新型载体又为TiO2/C光催化剂获得了阳极偏压,有利于将光生电子迅速导入载体,减少了光生载流子的复合.在新型光催化体系中,光化学氧化作用与光催化氧化作用有机地统一在同一电极/溶液界面附近,造成了该界面的强氧化环境,从而使有机分子的氧化降解速度得到显著提高.     

ZnTPP/TiO_2纳米复合催化剂的合成及其光催化活性的测定

<正>TiO2是一种环保型多相半导体光催化剂,对一些毒性大、生物难降解的有机污染物,用TiO2光催化剂催化生成的强氧化剂,在常温、常压下可以彻底地将有机物氧化为H2 O、CO2等小分子[1-3]。目前,TiO2主要用于中低浓度废水处理、小空间空气净化、材料表面自清洁、重金属回收、固体废物处理等领域。与传统除污工艺相比,具有无毒、安全、稳定性好、催化活性高、见效快、能耗低、可重     

H2O2络合凝胶法制备纳米TiO2/SiO2复合催化剂及其光催化性能

采用H2O2络合凝胶法获得钛的络合物[TiO(H2O2)]2 水溶胶,并与SiO2水溶胶包覆复合,制备了纳米TiO2/SiO2复合半导体催化剂,其结构经XRD和BET表征。以含阳离子艳红染料模拟废水降解为模型反应,考察了复合催化剂的光催化性能。实验结果表明:经650℃焙烧后的复合催化剂中TiO2粒径为9.8 nm,光催化活性最好,SiO2的最佳掺杂量为25%。     

Photodegradation of dye pollutants on one-dimensional TiO2 nanoparticles under UV and visible irradiation

Titanium dioxides (TiO₂) nanoparticles with one-dimensional (1D) geometry, nanorods and nanostripes, were used as photocatalysts to photodegrade Rhodamine B (RhB) under ultraviolet (UV) and visible irradiation. The nanorods catalyst exhibited very interesting photocatalytic properties: under the UV irradiation its catalytic activity was slightly below that of the well-known TiO₂ catalyst P25, while under visible light it exhibited a better activity than P25.This fact indicates that the nanorods have a superior ability to utilize less energetic but more abundant visible light. Moreover, the 1D TiO₂ nanoparticles can be readily separated from aqueous suspensions by sedimentation after the reaction. With these advantages the 1D TiO₂ catalysts have a great potential for environmental applications. Various analytical techniques were employed to characterize TiO₂ catalysts and monitor the photocatalytic reaction. It was found that the catalytic performance of the catalysts is greatly dependent on their structures: The superior activity of P25 (consists of anatase and rutile nanocrystals) under UV light results probably from the interfacial interaction between anatase and rutile nanocrystals in this solid, which do not exist in the nanorods (only anatase). The titanate nanostripes (titanate) can absorb UV photons with shorter wavelength only.     

Preparation of TiO2 Powder by Modified Two-Stage Hydrolysis

Nano-sized TiO₂ powders were synthesized by modified hydrolysis reaction using two-stage treatments of acid/base catalyst. Using an acidic catalyst, the primary particle size of assynthesized TiO₂ was smaller than using basic catalyst, but rutile ratio and the particle size were increased after heat treatment due to the dense packing of particles. However, in the synthesized TiO₂ powder using a basic catalyst persist the anatase phase and a loosely aggregation of particle after heat treatment. It was found that the catalyst used in the first stage determines the primary particle size. However the phase, the packing density and degree of dispersion of TiO₂ powder were determined by the secondly applied catalyst. Therefore, the addition sequence of catalysts is the most important key to prepare fine powders for photocatalytic use and solar cell. In this study, an acid treatment followed by a base is suggested as best route to obtaining fine size and distribution of particles and high content of anatase phase.     

Manifestation of the effect of strong metal-support interaction in a Pt/TiO2 rutile catalyst

Pt/TiO₂ catalysts supported on ultradispersed rutile are prepared. The effect of strong metal-support interaction (SMSI) in these catalysts is more pronounced than in Pt/TiO₂ catalysts with greater fractions of an anatase phase in the support. Mild oxidation of the rutile catalyst eliminates the SMSI effect.     

Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.     

二氧化钛催化超声波损伤牛血清白蛋白的研究

利用紫外可见(UV-Vis)光谱和荧光(FL)光谱研究了二氧化钛(TiO₂)催化超声波照射对牛血清白蛋白(BSA)的损伤作用，同时对金红石型和锐钛矿型TiO₂的催化性能进行了比较，并探讨了照射时间，TiO₂加入量，溶液酸度，超声波功率和离子强度等因素对BSA分子损伤的影响。结果表明，金红石型TiO₂的催化效果明显好于锐钛矿型TiO₂。在一定条件下，BSA分子的损伤程度随着照射时间的延长、照射功率和溶液酸度的增大而增大，而TiO₂的加入量和离子强度对BSA分子损伤的影响则较为复杂。     

硼铈共掺杂纳米TiO2光催化降解三氯杀螨醇和菊酯类农药

采用溶胶-凝胶法在钛酸丁酯水解过程引入硼酸、硝酸铈,制备具有光催化活性的硼铈共掺杂纳米二氧化钛（TiO2）,经XRD、TEM、FT-IR、UV-Vis-DRS表征晶体结构,在日光灯照射下,光催化降解三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯农药。结果表明：硼铈共掺杂的TiO2只有锐钛矿型,而纯的或掺铈的TiO2有含有锐钛矿型、金红石相和少量板钛矿型,UV-Vis-DRS测定结果表明硼铈共掺杂的TiO2禁带宽度变小,硼铈共掺杂的TiO2在可见光区吸光度高于掺杂铈和不掺杂的TiO2,在420nm~850nm有强的吸收;在同样光照下对三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯的降解试验证明硼铈共掺杂纳米TiO2的光催化活性高于不掺杂或只掺杂铈的TiO2。     

超临界流体干燥法制备纳米TiO2-SnO2-SiO2复合光催化剂及其光催化性能研究

半导体多相光催化法作为一种污染治理新技术越来越受到人们的重视,在所使用的半导体光催化剂中,TiO2以无毒,催化活性高,价廉,无污染等特点,成为最具有前途的绿色环保型催化剂之一[1],但其自身具有局限性,如禁带宽度大,需在近紫外光下才能激发产生电子空穴对,对太阳光的利用率仅     

Low temperature CO oxidation on Au/TiO2 sol-gel catalysts

A comparative study on Au/TiO₂catalysts prepared by impregnation with HAuCl₄of commercial TiO₂ or by impregnation of sol-gel derived TiO₂has been carried out during CO oxidation. Specific surface areas and mean Au particle of 49 and 74 m²/g and 35 and 25 Å were obtained for impregnated commercial TiO₂ and sol-gel preparations, respectively. XRD patterns shown that in sol-gel derived TiO₂ only anatase phase was identified, while in commercial TiO₂ anatase and rutile phases co-exist. Titania support effect on Au activity for the oxidation of CO has been observed. The light-off during the reaction on Au/TiO₂initiates at 50°C, whereas for commercial impregnated TiO₂ catalyst the light-off initiates at 200°C.     

Synthesis of nanosized TiO2/SiO2 catalysts by the ultrasonic microemulsion method and their photocatalytic activity

Nanosized TiO₂/SiO₂ catalysts prepared by hydrolysis of titanium n-butoxide in microemulsion showed enhanced photocatalytic activity. In the presence of catalyst ME-2 and after 90 min irradiation by UV light, methylene blue was completely converted evidenced by the absence of its absorption band in the UV-Vis spectra. This catalyst demonstrated much better degradation ability than P-25 and naked TiO₂.     

载有C60的TiO2纳米粒子光催化活性

以水溶性C₆₀和TiO₂粒子为前驱体,采用水热法制备了载有C₆₀的锐钛矿型TiO₂纳米粒子。应用X射线衍射、透射电子显微镜、红外光谱、紫外-可见漫反射光谱、荧光光谱对产物进行了表征。以对-硝基苯酚为模型污染物研究了产物的光催化活性,结果表明适量负载C₆₀可以提高TiO₂纳米粒子的光催化活性,C₆₀起着传输电子、促进TiO₂光生载流子分离的作用,且经7次循环使用后对-硝基苯酚的降解效率仍能达到74%。讨论了载有C₆₀的TiO₂纳米粒子光催化降解对-硝基苯酚的机理。