Preparation and characterization of anhydrous polymer electrolyte membranes based on poly(vinyl alcohol-<Emphasis Type="Italic">co</Emphasis>-ethylene) copolymer

Anhydrous polymer electrolyte membranes with cross-linked structure have been prepared based on poly(vinyl alcohol-co-ethylene) (PVA-co-PE) copolymer. The PVA units of copolymer served to induce thermal cross-linking with 4,5-imidazole dicarboxylic acid (IDA) via esterification while PE units controlled the membrane swelling and the mechanical properties of films. Upon doping with phosphoric acid (PA, H₃PO₄) to form imidazole-PA complexes, the proton conductivity of membranes continuously increased with increasing PA content. As a result, proton conductivity reached 0.01 S/cm at 100 °C under anhydrous conditions. X-ray diffraction analysis revealed that both the d-spacing and crystalline peak of membranes were reduced upon introduction of IDA/PA due to the cross-linking effect. The PVA-co-PE/IDA/PA membranes exhibited good mechanical properties, e.g., 150 MPa of Young’s modulus, as determined by a universal testing machine. Thermal gravimetric analysis also represented that the thermal stability of membranes was increased up to 200 °C upon introduction of IDA/PA.     

Composite membranes of sulfonated poly(phthalazinone ether ketone) doped with 12-phosphotungstic acid (H3PW12O40) for proton exchange membranes

Sulfonated poly(phthalazinone ether ketone) (SPPEK) and 12-phosphotungstic acid (PWA) composite membranes were prepared by the casting procedure, using SPPEK solution blended with PWA. The physicochemical properties of these composite membranes were studied by means of field-emission scanning electron microscopy (FSEM), X-ray diffraction (XRD) analysis, thermogravimetry analysis (TGA) and Fourier transform infrared attenuated total reflection (FTIR-ATR) spectroscopy. The PWA particles in composite membranes are stable due to the interaction between SO₃H group of SPPEK and PWA particles. The proton conductivity of the composite membrane containing 10% PWA reaches the maximum of 0.17 S/cm at 80 °C under 100% relative humidity.     

Identification of ionic aggregates in PVDF-g-PSSA membrane by tapping mode AFM and HADDF STEM

Previous literature has shown that poly(vinylidene fluoride)-graft-poly(styrene sulfonated acid) (PVDF-g-PSSA) exhibits a lower methanol permeability than commercial Nafion and so is better suited to use as a proton exchange membrane (PEM) in direct methanol fuel cells (DMFCs). A number of studies have suggested that the microstructures of ionic aggregates explain their lower methanol permeability, but few direct morphological observations have been reported. In this study, the use of a tapping mode atomic force microscope (AFM) and a high-angle annular dark-field (HAADF) scanning transmission electron microscope (STEM) has identified the phase separation of PVDF and sulfonated PS, and ionic sulfonic aggregates, 3-5 nm, in sulfonated PS regions. An experiment to elucidate the microstructural changes in the membrane with and without methanol immersion shows that PVDF-g-PSSA has ionic aggregates with a more stable microstructure than Nafion.     

Maghemite/poly(<Emphasis Type="SmallCaps">d,l</Emphasis>-lactide-<Emphasis Type="Italic">co</Emphasis>-glycolyde) composite nanoplatform for therapeutic applications

A reproducible methodology is described for the synthesis, by following the double emulsion/solvent evaporation technique, of magnetic nanocomposites (average diameter ≈ 135 nm) consisting of maghemite nuclei and a biodegradable poly(d,l-lactide-co-glycolide) matrix. The heterogeneous structure of the nanoparticles can confer them the responsiveness to magnetic gradients, giving both the possibility of their use as a drug delivery system and adequate heating characteristics for a hyperthermia effect. The physical chemistry of the nanocomposites was extensively characterized, this establishing that their surface properties were similar to that of pure poly(d,l-lactide-co-glycolide). From an electrokinetic point of view, zeta potential determinations (as a function of the ionic strength, and pH) pointed out that the nanocomposites were almost indistinguishable from the copolymer. The surface thermodynamic analysis agreed with the electrophoretic one in suggesting that the coverage of the magnetic nuclei was complete, since the hydrophilic nature of maghemite was modified and the nanoparticles turned into hydrophobic, just like the copolymer, when they were embedded into poly(d,l-lactide-co-glycolide). The magnetic behaviours of the composite nanoparticles were also checked. Their heating properties were studied in vitro in a high-frequency alternating gradient of magnetic field: a stable maximum temperature of 47 °C was satisfactorily achieved within 45 min. Blood compatibility of the nanocomposites was also defined in vitro. To our knowledge, this is the first time that such kind of magnetic-sensitive nanoformulation with very promising characteristics (e.g. blood compatibility, magnetic drug targeting capabilities, and hyperthermia) has been developed for therapeutic purposes.     

Proton conducting composite membranes comprising sulfonated Poly(1,4-phenylene sulfide) and zeolite for fuel cell

Sulfonated poly(1,4-phenylene sulfide; SPPS) was prepared from poly(1,4- phenylene sulfide) and fuming sulfuric acid by sulfonation process. Novel hybrid organic/inorganic composite polymer electrolyte membranes based on sulfonated poly(1,4-phenylene sulfide) membrane with varying concentrations of zeolite were synthesized. Fourier transform infrared spectroscopy implied the presence of a specific interaction between SPPS and zeolite particles. Upon increasing the zeolite concentration to 10 wt.%, the proton conductivity of composite membrane reduced from 0.075 to 0.02 S cm⁻¹ at room temperature which may be due to strong interaction between sulfonic group of SPPS and the zeolite particles. The water uptake of the composite membrane reduced from 255% to 150% with the increase of the zeolite concentration to 10 wt.%. The thermal stability analysis showed the enhancement of thermal stability of the composite membranes with increasing concentration of zeolite.     

Graft polymerization of poly(epichlorohydrin-g-poly((oxyethylene) methacrylate)) using ATRP and its polymer electrolyte with KI

This contribution demonstrates a synthesis of comb polymer consisting of a poly(epichlorohydrin) (PECH) backbone and poly(oxyethylene methacrylate) side chains. Atom transfer radical polymerization (ATRP) was used to directly initiate the chlorine atoms of PECH macroinitiator. The structure of comb polymer was characterized by nuclear magnetic resonance (¹H nuclear magnetic resonance) and Fourier transform infrared (FT-IR) spectroscopy, presenting the successful “grafting from” method using ATRP. The comb polymer was used as a polymer matrix for dissolving potassium iodide (KI) to prepare solid polymer electrolyte. FT-IR spectroscopy indicates that the potassium salts are dissolved in the polymeric matrix due to coordination interaction with the ether oxygens of graft copolymer. Differential scanning calorimetry showed that glass transition temperature (T _g) of polymer electrolytes continuously increased with increasing salt concentration up to 15 wt.%, mostly due to coordinative interactions between the potassium ions and the ether oxygens of polymer matrix. Ionic conductivity at room temperature increased with increasing salt concentrations up to 5 wt.% (maximum ionic conductivity ~3.7 × 10⁻⁵ S/cm), after which it gradually decreased.     

Multifunctional core–shell nanoparticles: superparamagnetic,mesoporous, and thermosensitive

Multifunctional core–shell composite nanoparticles (NPs) have been developed by the combination of three functionalities into one entity, which is composed of a single Fe₃O₄ NP as the magnetic core, mesoporous silica (mSiO₂) with cavities as the sandwiched layer, and thermosensitive poly(N-isopropylacrylamide-co-acrylamide) (P(NIPAAm-co-AAm)) copolymer as the outer shell. The mSiO₂-coated Fe₃O₄ NPs (Fe₃O₄@mSiO₂) are monodisperse and the particle sizes were varied from 25 to 95 nm by precisely controlling the thickness of mSiO₂-coating layer. The P(NIPAAm-co-AAm) were then grown onto surface-initiator-modified Fe₃O₄@mSiO₂ NPs through free radical polymerization. These core–shell composite NPs (designated as Fe₃O₄@mSiO₂@P(NIPAAm-co-AAm)) were found to be superparamagnetic with high r ₂ relaxivity. To manipulate the phase transition behavior of these thermosensitive polymer-coated NPs for future in vivo applications, the characteristic lower critical solution temperature (LCST) was subtly tuned by adjusting the composition of the monomers to be around the human body temperature (i.e. 37 °C), from ca. 34 to ca. 42 °C. The thermal response of the core–shell composite NPs to the external magnetic field was also demonstrated. Owing to their multiple functionality characteristics, these porous superparamagnetic and thermosensitive NPs may prove valuable for simultaneous magnetic resonance imaging (MRI), temperature-controlled drug release, and temperature-programed magnetic targeting and separation applications.     

Effect of a Novel Polymeric Coupling Agent on the Water Uptake Property and Warp Stability of Poly(vinyl chloride)/Bamboo Flour Composite

Water uptake property and warp stability of poly(vinyl chloride) (PVC)/bamboo flour composite were investigated employing a novel polymeric coupling agent, poly(styrene-co-maleic anhydride)-block-poly(styrene-co-acrylonitrile) {P[(SMA)-b-(SAN)]}. P[(SMA)-b-(SAN)] was synthesized through controlled/'living' radical polymerization (CRP) technique in an one-pot reaction and incorporated into the composite to improve the interfacial adhesion between PVC and bamboo flour. The structure of P[(SMA)-b-(SAN)] was confirmed by ¹H-NMR, FT-IR and GPC. PVC/bamboo flour composite sheets were then prepared from a single screw extruder and two-roll mill in the presence of P[(SMA)-b-(SAN)] coupling agent. As the content of the coupling agent increased, improved interfacial bonding between PVC and bamboo flour filler was observed. Water uptake property and warp stability were also improved in the presence of the coupling agent. These results suggest that the block copolymer successfully acted as a coupling agent in PVC/bamboo flour composites.     

SiMn–Graphite composites as anodes for lithium ion batteries

Two Si–Mn–C composites were obtained by sequentially ball milling the mixture of the silicon and manganese powders (atomic ratio of 3:5), followed by addition of 20 wt.% and 10 wt.% graphite, respectively. The phase structure and morphology of the composite were analyzed by X-ray diffraction (XRD) and scanning electromicroscopy (SEM). The results of XRD show that there is no new alloy phase in the composite obtained by mechanical ball milling. SEM micrographs confirm that the particle size of the Si–Mn–C composite is about 0.5–2.0 μm and the addition of graphite restrains the morphological change of active center (Si) during cycling. The Si–Mn particles are dispersed among the carbon matrix homogeneously, which ensures a good electrical contact between the active particles. Electrochemical tests show that the Si–Mn–C composite achieves better reversible capacity and cycleability. The Si–Mn–20 wt.% C composite electrode annealed at 200 °C for 2 h reveals an initial reversible capacity of 463 mAh·g^− 1 and retains 387 mAh·g^− 1 after 40 cycles.     

Synthesis and ionic conductivity of polymeric ion gel containing room temperature ionic liquid and phosphotungstic acid

Composite electrolyte comprising phosphotungstic acid (PWA) filler and 1-butyl-3-methyl-imidazolium-tetrafluoroborate (BMImBF₄) room temperature ionic liquid (RTIL) in poly(2-hydroxyethyl methacrylate) (PHEMA) matrix has been prepared. The polymer matrix was formed by free radical polymerization of 2-hydroxyethyl methacrylate (HEMA) monomers. BMImBF₄ was used as both ionic source and plasticizer, and PWA filler provided the proton conductivity in this system. The interactions and structure changes of the PHEMA-RTIL-PWA composites were investigated by Fourier transform infrared spectra, differential scanning calorimetry, and X-ray diffraction. PWA fillers maintained their Keggin structure within a limited range and enhanced the ionic conductivity of the composite electrolyte. The electrolyte with PWA at the 2 wt.% showed the highest ionic conductivity of 8 × 10^− 4 S cm^− 1 at room temperature and 96% relative humidity.     

Short electrospun composite nanofibers: Effects of nanoparticle concentration and surface charge on fiber length

Short composite nanofibers were fabricated by electrospinning polymer/TiO₂ nanoparticle solutions of 13 wt. % cellulose acetate as a polymer under a voltage of 5.5 kV and at a flow rate of 0.1 μL/min, and the nanoparticles could be added in concentrations as high as 50 wt. %. The length of the short composite nanofibers was significantly decreased from 112 to 70 μm by the addition of at least a 5 wt. % concentration of nanoparticles, and it gradually continued to decrease as the nanoparticle concentration was increased. The length of the short composite nanofibers with a low concentration of nanoparticles was affected by the surface charge of the nanoparticles, and negatively charged nanoparticles readily dispersed to the negatively charged polymers in solution, which resulted in an elongation of the fabricated short composite nanofibers.     

Studies on compatibilization of polypropylene/thermoplastic polyurethane blends and mechanism of compatibilization

This paper reports a study of compatibilization and the mechanism of compatibilization of polypropylene (PP)/thermoplastic polyurethane (TPU) blends with maleated polypropylene (PP-MA) and its graft copolymer with polyethylene oxide (PEO), (PP-MA)-g-PEO. The results of scanning electron microscope (SEM) and dynamic mechanical analysis showed that (PP-MA)-g-PEO was a very good compatibilizer for PP/TPU blends, while PP-MA also produced some compatibilization. The cocrystallization between bulk PP and PP segments of the compatibilizers was evidenced by differential scanning calorimetry studies. The specific interaction between TPU and polar parts of the compatibilizers was studied with Fourier transform infrared spectroscopy.     

Polyphosphazene based composite polymer electrolytes

Composite salt-in-polymer electrolyte membranes were prepared from poly[(bis(2-methoxyethyl)amino)_1−x(n-propylamino)_x-phosphazene] (BMEAP) with dissolved LiCF₃SO₃ and dispersed Al₂O₃ nanoparticles (40 nm). Membranes with good mechanical stability were obtained. Low ionic conductivities were found in particle free membranes with maximum conductivities at 10 wt.% LiCF₃SO₃ ranging from 3.1 × 10^− 7 S/cm at 30 °C to 1.8 × 10^− 5 S/cm at 90 °C. For the composite membranes, addition of 2 wt.% Al₂O₃ nanoparticles leads to a steep increase of the conductivity by almost two orders of magnitude as compared to the homogeneous membranes. The highest room temperature conductivity for the investigated BMEAP–LiCF₃SO₃–Al₂O₃ composite systems was 10^− 5 S/cm.     

Charge/discharge characteristics of sulfur composite electrode at different temperature and current density in rechargeable lithium batteries

The charge/discharge characteristics of the sulfur composite cathodes were investigated at different temperatures and different current densities. The composite presented the discharge capacities of 854 and 632 mAh g⁻¹ at 60 and −20 °C, respectively, while it had the discharge capacities of 792 mAh g⁻¹ at 25 °C. The composite presented the discharge capacities of 792 and 604 mAh g⁻¹ at 55.6 and 667 mA g⁻¹, respectively, at room temperature. The results showed that the sulfur composite cathodes presented good charge/discharge characteristics between 60 and −20 °C and at a high c-rate up to 667 mA g⁻¹.     

Preparation of TEMPO-contained pyrrole copolymer by in situ electrochemical polymerization and its electrochemical performances as cathode of lithium ion batteries

Composite electrodes based on the nitroxide free radical-contained pyrrole copolymer (PPy-co-PPy-C-TEMPO) as active material were one-step synthesized by in situ electrochemical polymerization, which was then directly applied as the cathode of lithium ion batteries. The structure, morphology, electrochemical property, and charge-discharge performances of prepared copolymers were characterized by FTIR, SEM, cyclic voltammogram, electrochemical impedance spectroscopy, and galvanostatic charge-discharge testing, respectively. The results demonstrated that PPy-co-PPy-C-TEMPO-based composite cathodes have been successfully prepared by in situ electrochemical method, and the introduction of the nitroxide free radical (TEMPO) could obviously affect the morphology and electrochemical characteristics of the obtained electroactive polymers. And the charge/discharge tests showed that with the introduction of the TEMPO, PPy-co-PPy-C-TEMPO-based composite cathodes exhibited an improved specific capacity of 70.9 mAh g^?1 for PPy-co-PPy-C-TEMPO (4:1) and 62.6 mAh g^?1 for PPy-co-PPy-C-TEMPO (8:1) as measured at 20 mA g^?1 between 2.5 and 4.2 V, which were remarkably higher than that of the pure PPy cathode of 41.0 mAh g^?1 under the same experimental conditions. Also, the obtained PPy-co-PPy-C-TEMPO copolymers demonstrated an acceptable cycling stability during the charge-discharge process. These obtained cell performances for the composite cathodes were attributed to the application of the in situ electrochemical polymerization technology, which enhanced the intimate integration between conductive polymer film and electrode. Furthermore, the introduction of TEMPO-contained pyrrole (Py-C-TEMPO) improved the morphology of the composite cathode, which was in favor of the utilization of active materials and the improved electrochemical performances.     

SAXS cluster structure and properties of sPEEK/PEI composite membranes for DMFC applications

Sulfonated poly(ether ether ketone)/polyethyleneimine (sPEEK/PEI) composite membranes were prepared to reduce the water uptake and methanol permeability of highly sulfonated PEEK membranes (> 65%). Incorporation of small amounts of PEI reduced ionic cluster size via electrostatic complex formation between anionic sulfonic groups of the sPEEK and the cationic amine groups of the PEI, and thus affected membrane properties considerably. Ion cluster size decreased with increasing PEI concentration by small angle X-ray scattering pattern. Addition of 1 wt.% of PEI resulted in reduction of water uptake and methanol permeability by 30% at 60 °C and 85% at room temperature, respectively. The thermal and mechanical stabilities were also enhanced by formation of physical cross-linking induced by electrostatic interactions between acid/base polymers. Although proton conductivity was also reduced by PEI incorporation as a part of the sulfonic acid groups involved in ionic complex formation, its effect on proton conductivity was not as strong as on methanol permeability.     

The effect of polystyrene-block-poly(4-vinylpyridine) prepared by a RAFT method in the dispersion polymerization of styrene

The dispersion polymerization of styrene has been carried out using polystyrene-block-poly(4-vinylpyridine) copolymer [P(S-b-4VP)], prepared by a reversible addition-fragmentation chain transfer (RAFT) method, as a steric stabilizer in alcohol media. These block copolymer contains a long poly(4-vinylpyridine) block and a short polystyrene block. The stable spherical particles were obtained when the block copolymer concentrations increased from 2 to 20 wt.% relative to the monomer and the average particle sizes decreased from 340 to 200 nm with increasing concentration of the block copolymer. Alcoholic solvents, from methanol to n-hexanol, are responsible for the particle size. These results indicate that the poly(S-b-4VP) block copolymer is effective for providing polystyrene nano-sized particles with a low content of it working as a good stabilizer in any kind of alcoholic medium.     

Synthesis and properties of side-chain-type ion exchange membrane PEEK-g-StSO3Na for bipolar membranes

Side-chain-type ion exchange membranes (PEEK-g-StSO₃Na) were prepared by grafting poly (ether ether ketone) (PEEK) containing propenyl groups with sodium sulfonic styrene (StSO₃Na) and KH570. PEEK was synthesized by the aromatic nucleophilic polycondensation reaction of 4,4′-difluorobenzophenone, bisphenol A and diallylbisphenol A. The synthesized copolymers with the -SO₃Na group on the side chain of polymers possessed high molecular weights. The cross-linking reaction was carried out through a sol-gel reaction of the trimethoxysilane group. The copolymer membranes exhibited excellent mechanical properties due to their aromatic structure extending through the backbone and flexible StSO₃Na aliphatic chains. The ion exchange capacities (IECs) of the membranes ranged from 2.27 to 2.50 mmol g⁻¹ and the water content ranged from 107.2 to 126.1%, with both parameters increasing with StSO₃Na grafting degree. The H⁺ permeability of copolymer membranes increased with increasing IEC, reaching value above 0.3056 mol/L at 2 h, which is higher than that of Nafion^® 117 at the same measurement condition. They displayed reasonably high H⁺ permeability due to the higher acidity of benzoyl sulfonic acid group, the larger interchain spacing, which is available for water occupation, and the lower AC impedance of the bipolar membrane.     

LiFAP-based PVdF–HFP microporous membranes by phase-inversion technique with Li/LiFePO<Subscript>4</Subscript> cell

Polyvinylidenefluoride–hexafluoropropylene-based (PVdF–HFP-based) gel and composite microporous membranes (GPMs and CPMs) were prepared by phase-inversion technique in the presence 10 wt% of AlO(OH) _n nanoparticles. The prepared membranes were gelled with 0.5-M LiPF₃(CF₂CF₃)₃ (lithium fluoroalkylphosphate, LiFAP) in EC:DEC (1:1 v/v) and subjected to various characterizations; the AC impedance study shows that CPMs exhibit higher conductivity than GPMs. Mechanical stability measurements on these systems reveal that CPMs exhibit Young’s modulus higher than that of bare and GPMs and addition of nanoparticles drastically improves the elongation break was also noted. Transition of the host from α to β phase after the loading of nanosized filler was confirmed by XRD and Raman studies. Physico-chemical properties, like liquid uptake, porosity, surface area, and activation energy, of the membranes were calculated and results are summarized. Cycling performance of Li/CPM/LiFePO₄ coin cell was fabricated and evaluated at C/10 rate and delivered a discharge capacity of 157 and 148 mAh g⁻¹ respectively for first and tenth cycles.     

Polymer electrolytes based on copolymer of poly(ethylene glycol) dimethacrylate and imidazolium ionic liquid

Polymer electrolytes based on the copolymer of N-vinylimidazolium tetrafluoroborate (VyImBF₄) and poly(ethylene glycol) dimethacrylate (PEGDMA) have been prepared. Ethylene carbonate (EC) and LiClO₄ are added to form gel polymer electrolytes. The chemical structure of the samples and the interactions between the various constituents are studied by FT-IR. TGA results show that these polymer electrolytes have acceptable thermal stability, are stable up to 155 °C. Measurements of conductivity are carried out as a function of temperature, VyImBF₄ content in poly(VyImBF₄-co-PEGDMA), and the concentration of EC and LiClO₄. The conductivity increases with PEGDMA and EC content. The highest conductivity is obtained with a value of 2.90 × 10^? 6 S cm^? 1 at room temperature for VP1/EC(25 wt.%)–LiClO₄ system, corresponding to the LiClO₄ concentration of 0.70 mol kg^? 1 polymer.