AP-TPR-MS法考察六枝煤固定床热解过程中的硫变迁行为

实验选取六枝(LZ)原煤及其在固定床热解所得半焦,采用常压程序升温还原 质谱法（AP-TPR-MS）与化学法相结合考察温度和气氛对固定床热解过程中硫变迁行为的影响。对于LZ煤而言,经氮气气氛500℃热解后,只能使煤中部分不稳定有机硫分解,黄铁矿硫却不能分解;而经氮气气氛700℃热解后可以使不稳定有机硫和黄铁矿硫全部分解。合成气气氛在500℃以前煤中的不稳定有机硫和黄铁矿硫就能全部分解,且随着温度的升高,合成气表现出与氢气相近的脱硫活性。1.0% O₂-N₂对于六枝煤并没有明显的脱硫效果,这与氮气气氛相差不大。     

Release and enrichment of 44 elements during coal pyrolysis of Yima coal, China

The coal samples were collected from Yima coal district, China. The pyrolysis experiments were carried out in a simulated bed quartz reactor with a heating rate of 20 °C/min. The 44 elements in raw coal and chars were determined by inductively coupled-plasma mass spectrometry instrument (ICP-MS). The release and enrichment behavior of 44 trace elements during coal pyrolysis of Yima coal was studied.

According to the transformation behaviors, chemical features and thermal features under different pyrolysis temperatures, the 44 elements can be categorized to 4 groups: light elements (Li and Be), nonmetal elements (Se, As, B, etc.), heavy metal elements (including 24 elements, Cu, V, Co, etc.) and rear earth elements (REE) (14 elements). The results showed that (1) the higher pyrolysis temperatures, the higher release ratio and release ratio of REE are very low; (2) the enrichment ratios of the elements in chars increase by the sequence of nonmetal elements < light elements < heavy metal elements < REE. The nonmetal elements, light elements and a few heavy metal elements will be emitted out from coal during coal pyrolysis and they will pollute environment.     

Comparative study of pretreatment methods for the determination of metals in atmospheric aerosol by electrothermal atomic absorption spectrometry

A comparative study of pretreatment methods for the determination of 10 elements (As, Cd, Pb, V, Ni, Mn, Cr, Cu, Fe, Al) in atmospheric aerosols by electrothermal atomic absorption spectrometry (ETAAS) was conducted. For the digestion of the particulates collected in filters, six methods were compared using a mixture of HNO₃ and HF with or without the addition of various oxidative agents (HClO₄ or H₂O₂) or acids (HCl). The comparative study was performed using loaded cellulose filter samples, which were digested in Parr bombs and heated in a conventional oven at 170 °C for 5 h. The extraction efficiency and blanks were compared and it was proved that the digestion method using only HNO₃–HF extracted most of the metals and gave the lowest blanks. The HNO₃–HF mixture was selected for the development of an improved microwave digestion method specific for aerosol-loaded filters. The operating parameters were optimized, so that quantitative recovery of the reference materials NIST 1649a urban dust and NIST 1648 urban particulate matter was achieved. The blank of cellulose and teflon filters were also determined and compared. Teflon filters present the lowest blanks for all the elements. The obtained limits of detection for each type of filters were adequate for environmental monitoring purposes. ETAAS instrumental operation was also optimized for the compensation and the elimination of interferences. The temperature optimization was performed for each metal in every type of filter and optimized parameters are proposed for 10 elements.     

Three interpenetrated frameworks constructed by long flexible N,N′-bipyridyl and dicarboxylate ligands

Three interpenetrated polymeric networks, {[Co(bpp)(OH-BDC)] · H₂O}_n (1) [Ni(bpp)_1.5(H₂O)(OH-BDC)]_n (2) and {[Cd(bpp)(H₂O)(OH-BDC)] · 2H₂O}_n (3), have been prepared by hydrothermal reactions of 1,3-bis(4-pyridyl)propane (bpp), 5-hydroxyisophthalic acid (OH-H₂BDC), with Co(NO₃)₂ · 6H₂O, Ni(NO₃)₂ · 6H₂O and Cd(NO₃)₂ · 4H₂O, respectively. Single-crystal X-ray diffraction analyses reveal that the three compounds all exhibit interpenetrated but entirely different structures. Compound 1 is a fourfold interpenetrated adamantanoid structure with water molecules as space fillers, in which bpp adopts a TG conformation (T = trans, G = gauche). Compound 2 is an interdigitated structure from the interpenetrated long arms of one-dimensional molecular ladders, while bpp in 2 adopts both TT and TG conformations. Compound 3 is a twofold interpenetrated three-dimensional network from a one-dimensional metal-carboxylate chain bridged by TG conformational bpp. The hydrogen bonding interactions in 1–3 further stabilize the whole structural frameworks and play critical roles in their constructions.     

不同气氛下煤连续热解产物的分配规律及产品品质分析

在连续进出料的流化床中研究了热解温度为850 ℃时,含有O₂、H₂、CO、CO₂、CH₄的反应气氛对热解产物分配规律及产品组成的影响。采用Raman、BET等测试方法对不同热解气氛下制得半焦的品质进行了评价,结合热重分析了影响半焦反应活性的因素。结果表明,无O₂气氛下,H₂与CO₂存在时降低了焦油产率,而CO与CH₄促进了焦油的生成。CH₄的裂解析碳使半焦产率上升。O₂的加入使CO₂、CO含量明显增加,半焦及焦油产率降低。N₂中引入O₂时,PAHs含量降低。CH₄促进了烷基萘与苯类的生成,CO则抑制酚类裂解生成苯类。CO₂的气化作用促进了微孔的生成,相应地,半焦的比表面积快速增加,半焦的反应活性也最高。CO歧化与CH₄热裂解产生的析碳堵塞了部分孔道,降低了比表面积。H₂与CH₄所产生的氢自由基能渗透到半焦内部,引起半焦结构的缩聚,进而影响氧化反应活性。     

二氧化碳和水气氛对高钠煤转化过程中钠迁移的影响

对新疆的两种高钠煤（伊犁煤YL、呼图壁煤HTB）进行了N₂、CO₂和H₂O气氛和不同温度下钠迁移的研究。采用逐级萃取和湿法消解法确定了原煤、半焦中钠的赋存形态,定量研究了两种煤中钠的挥发及迁移规律。结果表明,YL煤的形态钠中水溶钠占80.08%,HTB煤的形态钠中不溶钠占61.54%。不同气氛下,升高温度都可促进两种煤中钠的挥发,半焦中水溶钠比例减小,醋酸铵可溶钠比例会出现先增加后减少现象,盐酸可溶钠比例呈增加趋势。对于YL煤,CO₂气氛可抑制钠的挥发,H₂O蒸气可促进钠的挥发;900℃时,YL煤CO₂气氛下钠挥发仅为N₂气氛下的50.25%,而H₂O气氛钠挥发为N₂气氛下的111.45%。对于HTB煤,CO₂气氛也可抑制钠的挥发,900℃时CO₂气氛下钠挥发为N₂气氛的80.91%;HTB煤在H₂O蒸气下,800℃之前钠挥发高于N₂,当900℃时,钠挥发略低于N₂气氛。YL煤形态钠中以水溶钠为主,其挥发的同时会向盐酸可溶钠及不溶钠转变。而HTB煤形态钠中以不溶钠为主,其次是水溶钠,CO₂和H₂O气氛能促进不溶钠向其他可溶态钠转变。     

Molecular, supramolecular structure and catalytic activity of transition metal complexes of phenoxy acetic acid derivatives

Six mononuclear complexes [M(L₁)₂(H₂O)₄] (M = Co(II), 1a and M = Mn(II), 1b), [Cu(L₁)₂(H₂O)₂] (1c), [Cu(L₁)₂(H₂O)(Py)₂] (1d), [Cu(L₃)(H₂O)Cl] · H₂O (3a) and [Co(Sal)(H₂O)(Py)₃] · 2ClO₄ · H₂O (3b) of phenoxyacetic acid derivatives and Schiff base were determined by single crystal X-ray diffraction. The Co(II) (1a) and Mn(II) (1b) complexes are isomorphous. X-ray crystal structural analyses reveal that these coordination complexes form polymeric structure via formation of different types of hydrogen bonding and π-stacking interactions in solid. Thermal analysis along with the powder X-ray diffraction data of these complexes shows the importance of the coordinated and/or crystal water molecules in stabilizing the MOF structure. Complexes 1a, 1c, 3a show marginal catalytic activity in the oxidation of olefins to epoxides in the presence of i-butyraldehyde and molecular oxygen.     

神府烟煤水煤浆快速热解焦结构演化及其反应性的研究

利用高频热解装置对神府烟煤水煤浆及其原煤进行了600~1 200 ℃条件下的快速热解实验,考察了两者快速热解后的煤焦产率、焦-C产率随热解温度的变化规律.利用XRD、氮气气体吸附法、SEM等测试手段对比分析了水煤浆及煤粉热解后煤焦的微晶结构、孔隙特征及表观结构;在热重分析仪上进行CO₂气化反应活性的测定,对比了水煤浆和煤粉热解后煤焦的气化活性.实验表明,随着热解温度的升高,水煤浆和煤粉的热解焦产率、焦-C产率均逐渐降低,热解温度低于900 ℃时,两者热解焦产率、焦-C产率趋于一致,热解温度高于900 ℃时,水煤浆热解焦产率和焦-C产率明显低于煤粉热解焦;高温热解条件下,水煤浆热解焦的微晶有序化程度比煤粉热解焦略高,比表面积明显高于煤粉热解焦,水煤浆热解焦的气化活性优于煤粉热解焦.     

煤中痕量元素在循环流化床锅炉中的迁移行为与富集特性

对天津市某电厂循环流化床(CFB)锅炉燃用的原煤及燃烧产物底灰、飞灰、细飞灰(≤50 μm)进行痕量元素含量的测定,分析了Be、Zn、Hg、V、Cr、Mn、Co、Ni、Cu、As、Se、Cd、Pb 13种痕量元素在燃烧过程中的迁移行为,揭示了痕量元素在CFB锅炉中的分配、富集特性。结果表明,CFB锅炉中,较低的炉温对于痕量元素的迁移富集产生了较大的影响。由相对富集系数得知,Be、V、Co、Se在底灰中耗散,在飞灰中富集,Zn、Mn倾向于在底灰中富集,元素Cd、Pb、Ni、Cu挥发性较强,在底灰和飞灰中均是耗散。As受钙氧化物影响,挥发性表现并不明显。Hg在底灰和飞灰中相对富集系数均很低,表明Hg在整个燃烧过程中以气态形式排放;Hg、As、Se、V、Cr、Mn、Co、Ni、Cu、Zn、Pb均有向小颗粒物中富集的趋势。根据相对富集系数以及研究的13种元素在低温CFB锅炉中的迁移行为,将这些元素分为三类:A类(E_R<0.1),主要是以气态形式排放元素Hg;B类(0.1R≤0.85),较易挥发元素As、Be、Ni、Cu、Se、Cd、Pb、Co、V;C类(E_R>0.85),主要残留在固体产物中元素Zn、Mn、Cr。     

Single-step microwave digestion with HNO(3) alone for determination of trace elements in coal by ICP spectrometry

A microwave digestion method with HNO₃ alone was conducted at a temperature as high as 250 °C for determination of 19 trace elements (Li, Be, V, Cr, Mn, Co, Ni, Cu, Zn, Ga, As, Se, Rb, Sr, Cd, Cs, Ba, Hg, and Pb) in coal jointly by inductively coupled plasma optical emission spectrometry (ICP-OES), inductively coupled plasma mass spectrometry (ICP-MS), and flow injection ICP-MS (FI-ICP-MS). The validity of determination was assessed by using three standard coals, SRM 1632c, BCR 180, and SARM 19. It was found that the high-temperature digestion led to an extensive decomposition of the organic matrix and clay in coal, and no dissolved and solid carbon remained in the final solution after evaporation. Good recoveries were observed for all trace elements in three coals, with the exception of V, Rb, and Cs in high-ash SARM 19. Additionally, FI-ICP-MS combined with the present digestion without evaporation pretreatment was proved to be a rapid and efficient approach for determination of ultra-trace elements such as Se, Cd, and Hg in coal.     

含油污泥与配合煤共热解煤焦的微观结构与气化反应特性

以含油污泥与配合煤为原料在850-1150℃热解制得焦样,采用N_2吸附-脱附和X射线衍射(XRD)分析煤焦孔隙结构及碳微晶结构,并运用热重分析(TGA)考察热解温度和含油污泥添加量对煤焦气化反应活性的影响。结果表明,提高热解温度和添加含油污泥能促进煤焦形成更加丰富的孔隙结构,强化煤焦-CO_2气化反应接触并抑制煤焦石墨化进程,从而提高煤焦气化反应活性;然而,热解温度过高或添加油泥量过多则会致使煤焦结构致密或孔隙堵塞,气化反应活性反而降低。     

High pressure performance of thin Pd–23%Ag/stainless steel composite membranes in water gas shift gas mixtures; influence of dilution, mass transfer and surface effects on the hydrogen flux

The hydrogen permeation and stability of tubular palladium alloy (Pd–23%Ag) composite membranes have been investigated at elevated temperatures and pressures. In our analysis we differentiate between dilution of hydrogen by other gas components, hydrogen depletion along the membrane length, concentration polarization adjacent to the membrane surface, and effects due to surface adsorption, on the hydrogen flux. A maximum H₂ flux of 1223 mL cm⁻² min⁻¹ or 8.4 mol m⁻² s⁻¹ was obtained at 400 °C and 26 bar hydrogen feed pressure, corresponding to a permeance of 6.4 × 10⁻³ mol m⁻² s⁻¹ Pa^−0.5. A good linear relationship was found between hydrogen flux and pressure as predicted for rate controlling bulk diffusion. In a mixture of 50% H₂ + 50% N₂ a maximum H₂ flux of 230 mL cm⁻² min⁻¹ and separation factor of 1400 were achieved at 26 bar. The large reduction in hydrogen flux is mainly caused by the build-up of a hydrogen-depleted concentration polarization layer adjacent to the membrane due to insufficient mass transport in the gas phase. Substituting N₂ with CO₂ results in further reduction of flux, but not as large as for CO where adsorption prevail as the dominating flow controlling factor. In WGS conditions (57.5% H₂, 18.7% CO₂, 3.8% CO, 1.2% CH₄ and 18.7% steam), a H₂ permeance of 1.1 × 10⁻³ mol m⁻² s⁻¹ Pa^−0.5 was found at 400 °C and 26 bar feed pressure. Operating the membrane for 500 h under various conditions (WGS and H₂ + N₂ mixtures) at 26 bars indicated no membrane failure, but a small decrease in flux. A peculiar flux inhibiting effect of long term exposure to high concentration of N₂ was observed. The membrane surface was deformed and expanded after operation, mainly following the topography of the macroporous support.     

钾和一氧化碳对松木屑快速热解半焦特性的影响

利用固定床反应器、红外光谱仪、吸附仪、X射线衍射仪、电感耦合等离子原子发射光谱仪、偏光显微镜等对比研究了原生生物质(原生物质)及水洗脱钾生物质(脱钾生物质)在N_2及富一氧化碳(CO)气氛下所得半焦的产率、官能团及其他物化结构的变化规律。研究表明,与脱钾生物质相比,热解温度低于750℃时,原生物质的半焦产率降低、比表面积增大、芳环结构减少而烷基、脂肪族结构等增加;与N_2相比,富CO气氛下所得半焦产率降低、比表面积增大,芳香结构、脂肪族结构、烷基减小。而热解温度高于750℃时,生物质中的钾和热解气氛中的CO均使生物质半焦产率增加、官能团数量和比表面积减少。利用偏光显微镜对生物质半焦表面矿物质的研究表明,热解温度低于750℃时,所得半焦表面矿物组分较少且高度分散;热解温度高于750℃时,所得半焦表面矿物组分较多,分布密集且熔融团聚现象随温度升高而增多。而对于半焦石墨化程度的研究表明,半焦石墨化程度随温度升高而增加,但低热解温度所得半焦的石墨化程度较差。温度高于750℃时,CO气氛使石墨化程度增加,而钾使石墨化程度降低。     

氧气对胜利褐煤水蒸气气化半焦结构及反应性的影响

为了研究氧气对半焦的结构变化和反应性的影响,采用不锈钢模拟气流床反应器,在8种不同气氛,800和900 ℃条件下,进行了胜利褐煤水蒸气气化实验。利用拉曼光谱和热重分析仪分别表征了半焦的结构和本征反应性。结果表明,在800和900 ℃条件下,添加的氧气对半焦结构变化的影响方式不同;半焦结构的变化是影响碱金属和碱土金属(AAEM)挥发的主要因素。在不同温度下,添加的氧气对Na挥发的影响和对结构的作用类似,H₂O/O₂混合气氛促使气化所得半焦的反应性进一步降低。半焦的反应活性指数与拉曼光谱谱带比值 I (G_R+V_L+V_R)/I_D具有很好的相关性。     

Electron beam treatment of lignite-burning flue gas with high concentrations of sulfur dioxide and water

Experiments were carried out to investigate the removals of SO₂ and NO_x from simulated lignite-burning flue gas containing SO₂ (4800 ppm), NO (320 ppm) and H₂O (22%) by electron beam irradiation. Removal efficiencies of SO₂ and NO_x were achieved to reach 97 and 88% at 70°C, and 74 and 85% at 80°C, respectively, with the dose of 10.3 kGy without NH₃ leakage. The higher removal efficiencies of SO₂ and NO_x were observed in simulated lignite-burning flue gas than in coal-fired flue gas containing 800 ppm of SO₂, 225 ppm of NO and 7.5% H₂O at the same treatment condition. The higher removal efficiencies were attributed to the higher concentrations of SO₂, H₂O, and added NH₃. Simulation calculations indicated that the higher concentrations of these components enhance the effective radical reactions to oxidize NO to form NO₂ with HO₂ radical, and to oxidize SO₂ to form SO₃ with OH radical and O₂. The reactions of NO_x with N and NH₂ radicals to produce N₂ and N₂O also promote the NO_x removal. By-product was determined to be the mixture of (NH₄)₂SO₄ and NH₄NO₃ containing a small amount of H₂SO₄.     

神府煤热解-活化耦合反应产物特性及机制研究

利用两段式固定床反应装置,研究了神府煤热解-活化耦合产物的特性,探讨了热解温度及活化剂(H_2O(g)、CO_2和H_2O(g)/CO_2)对产物性能的影响,揭示了热解-活化耦合反应机制。结果表明,热解温度对半焦的CO_2化学反应性影响较小;采用热解-活化两段耦合工艺,可使神府煤热解的焦油产率明显提高,产率最高为17.8%;不同活化剂对两段耦合过程产生的混合煤气(mixture coal gases,MCG)和焦油产率影响为H_2O(g)H_2O(g)/CO_2CO_2,其焦油组分均以饱和分和芳香分为主;采用H_2O(g)/CO_2(1∶1)活化剂,可有效提高活性炭的比表面积,其BET比表面积为845.37 m~2/g。热解-活化耦合机制主要为活化段产生的合成气(synthesis gases,SG)为热解段煤的加氢热解提供了氢源,丰富的氢自由基促进了煤的加氢热解反应,改变了耦合过程的产物分布和特性。     

Synthesis and X-ray crystallographic characterization of copper and iron complexes with tetradentate-N4 ligands: Reactivity towards catechol oxidation

The reaction of copper chloride dihydrate and ferric chloride hexahydrate with a tripodal N₄ ligand (ntb) under mild conditions affords two novel complexes [Cu(ntb)Cl]₂[CuCl₄] · 2H₂O (1) and [Fe(ntb)Cl₂]Cl · 3H₂O (2). The reaction of ferric chloride with another N₄ ligand, bispicpn, forms an octahedral mononuclear complex, [Fe(bispicpn)Cl₂]Cl (3). Single-crystal X-ray structural studies of 1, 2 and 3 reveal the formation of hydrogen-bond sustained 3D, 2D and 1D networks, respectively, involving (N–HO) and (N–HCl) interactions. The packing arrangement in 2 further reveals the existence of hexagonal channels with helical propagation along the diagonal of the crystallographic b- and c-axes. The reactions of these complexes with 3,5-di-tert-butylcatechol have been studied in dimethylformamide. NMR techniques have been used to identify the reaction products.     

Multi-elemental analysis of non-food packaging materials by inductively coupled plasma-time of flight-mass spectrometry

Commercial non-food packaging materials of four different matrices (paper, low density polyethylene (LDPE), polyethylene-polypropylene (PE-PP) and high density polyethylene (HDPE)) were examined for the content of Cr, Ni, Cu, Zn, As, Mo, Cd, Sb, Ba, Hg, Tl, Pb and U. The examined samples (0.17–0.35 g) were digested in HNO₃ and H₂O₂ (papers, LDPE and PE-PP) and in HNO₃, H₂SO₄ and H₂O₂ (HDPE) using microwave assisted high pressure system. The inductively coupled plasma-time of flight-mass spectrometry (ICP-TOFMS) has been employed as the detection technique. All measurements were carried out using internal standardization. Yttrium and rhodium (50 ng g⁻¹) were used as internal standards. The detection and quantification limits obtained were in the range of 0.005 ng g⁻¹ (⁵²Cr) to 0.51 ng g⁻¹ (⁶⁶Zn) and 0.015 μg g⁻¹ (⁵²Cr) to 2.02 μg g⁻¹ (⁶⁶Zn) of dry mass, respectively. The evaluated contents (mg kg⁻¹) of particular elements in the examined materials were as follows: 0.22–219; <1.05–9.03; 1.25–112; <2.02–449; <0.98–<1.30; <0.36–2.06; <0.29–113; <0.22–44.1; <0.06–57.4; <0.66–<0.88; <0.08–0.24; <0.13–1222 and <0.08–0.44 for Cr, Ni, Cu, Zn, As, Mo, Cd, Sb, Ba, Hg, Tl, Pb and U, respectively.     

Supported carbon molecular sieve membranes based on a phenolic resin

The preparation of a composite carbon membrane for separation of gas mixtures is described. The membrane is formed by a thin microporous carbon layer (thickness, 2 μm) obtained by pyrolysis of a phenolic resin film supported over a macroporous carbon substrate (pore size, 1 μm; porosity, 30%). The microporous carbon layer exhibits molecular sieving properties and it allows the separation of gases depending on their molecular size. The micropore size was estimated to be around 4.2 Å. Single and mixed gas permeation experiments were performed at different temperatures between 25°C and 150°C, and pressures between 1 and 3.5 bar. The carbon membrane shows high selectivities for the separation of permanent gases like O₂/N₂ system (selectivity≈10 at 25°C). Gas mixtures like CO₂/N₂ and CO₂/CH₄ are successfully separated by means of prepared membranes. For example, the membrane prepared by carbonization at 700°C shows at 25°C the following separation factors: CO₂/N₂≈45 and CO₂/CH₄≈160.     

XRD和Raman法评估热解气氛中H_2和CO对半焦化学结构的影响

采用XRD和Raman光谱分析方法研究了神木煤在热解主要温度区间(450-750℃)及在三种热解气氛(N_2、含H_2及含CO)下的化学结构演变规律,并比较了两种方法所获结构参数的相关性。结果表明,原煤在N_2气氛下热解制备的半焦,其炭微晶尺寸在横向上不断增长,纵向上层面间距逐渐增大,堆垛高度在650℃左右剧烈转变; Raman参数A_(D_1)/A_G增加,而A_G/A_(all)降低,表明半焦有序性结构比例降低。热解气氛中的H_2促进了炭微晶结构的纵向发展,提高了小分子基团的转化程度,使得半焦有序化程度升高。热解气氛中的CO对炭微晶结构参数影响小于H_2气氛,但在700℃以下,CO因析炭作用产生的致密炭颗粒包裹于半焦表面,导致半焦炭有序化程度提高。半焦的L_c与A_G/A_(all)及d_(002)与A_(D_1)/A_G之间存在一定相关性; L_a与A_(D_1)/A_G呈较好的正相关性。