Determination of organophosphorous pesticides in the ppq range using a simple solid-phase extraction method combined with dispersive liquid-liquid microextraction

Solid-phase extraction combined with dispersive liquid-liquid microextraction (SPE-DLLME) was applied for the extraction of six organophosphorous pesticides (OPPs) in water samples. The analytes considered in this study were determined by gas chromatography with mass spectrometry and included prophos, diazinon, chlorpyrifos methyl, methyl parathion, fenchlorphos and chlorpyrifos. Several extraction conditions (extraction solvent and elution/dispersion solvents nature, extraction solvent volume, elution solvent volume, water volume and sample volume) were tested for SPE-DLLME with these analytes and the best results were obtained using carbon tetrachloride as the extraction solvent and acetone as the elution/dispersion solvent. Calibration curves for the determination of OPPs in water samples were constructed in the concentration range of 10-100 ng/L. Limits of detection (LODs) ranged from 38 to 230 pg/L values that are below the maximum admissible level for drinking water (100 ng/L). Relative standard deviations (RSD) were between 8.6 and 10.4% for a fortification level of 100 ng/L. At the same fortification level, the relative recoveries (R.R.) of tap, well and irrigation water samples were in the range of 30.2-97.1%.     

Dispersive liquid-liquid microextraction of organophosphorous pesticides using nonhalogenated solvents

Dispersive liquid-liquid microextraction (DLLME) combined with gas chromatography and mass spectrometry (GC-MS) was applied to the determination of five organophosphorous pesticides (OPPs) in water samples. The analytes included in this study were prophos, diazinon, chlorpyrifos methyl, fenchlorphos, and chlorpyrifos. The use of nonhalogenated solvents (cyclohexane, heptane, and octane) as extraction solvents was investigated using acetone, acetonitrile, or methanol, as dispersion solvents. The combination of less polar dispersion solvents (1-propanol and 2-propanol) and nonhalogenated extraction solvents was also studied in dispersive liquid-liquid microextraction for the first time. Several experimental conditions were tested (nature and volume of extraction solvents, nature and volume of dispersion solvents, salting-out effect) and the corresponding enrichment factors and recoveries were evaluated. The best microextraction condition was obtained using 50 μL of cyclohexane and 0.3 mL of 1-propanol. The detection and quantification limits were in the low ppt range, with values between 3.3-8.0 ng/L and 11.0-26.6 ng/L, respectively. Relative standard deviations were between 6.6 and 13.1% for a fortification level of 500 ng/L. At the same fortification level, the relative recoveries (RR) of Alvito's dam water, Judeu's river water, and well water samples were in the range of 50.3-97.1%.     

Validation of an SPME method,using PDMS,PA, PDMS-DVB,and CW-DVB SPME fiber coatings,for analysis of organophosphorus insecticides in natural waters

Solid-phase microextraction (SPME) has been optimized and applied to the determination of the organophosphorus insecticides diazinon, dichlofenthion, parathion methyl, malathion, fenitrothion, fenthion, parathion ethyl, bromophos methyl, bromophos ethyl, and ethion in natural waters. Four types of SPME fiber coated with different stationary phases (PDMS, PA, PDMS-DVB, and CW-DVB) were used to examine their extraction efficiencies for the compounds tested. Conditions that might affect the SPME procedure, such as extraction time and salt content, were investigated to determine the analytical performance of these fiber coatings for organophosphorus insecticides. The optimized procedure was applied to natural waters - tap, sea, river, and lake water - spiked in the concentration range 0.5 to 50 micro g L(-1) to obtain the analytical characteristics. Recoveries were relatively high - >80% for all types of aqueous sample matrix - and the calibration plots were reproducible and linear (R(2)>0.982) for all analytes with all the fibers tested. The limits of detection ranged from 2 to 90 ng L(-1), depending on the detector and the compound investigated, with relative standard deviations in the range 3-15% at all the concentration levels tested. The SPME partition coefficients (K(f)) of the organophosphorus insecticides were calculated experimentally for all the polymer coatings. The effect of organic matter such as humic acids on extraction efficiency was also studied. The analytical performance of the SPME procedure using all the fibers in the tested natural waters proved effective for the compounds.     

Ionic liquid-based dispersive liquid-liquid microextraction for sensitive determination of aromatic amines in environmental water

Ionic liquid-based dispersive liquid-liquid microextraction was developed for the extraction and preconcentration of aromatic amine from environmental water. A suitable mixture of extraction solvent (100 μL, 1-butyl-3-methylimidazolium hexafluorophoshate) and dispersive solvent (750 μL, methanol) were injected into the aqueous samples (10.00 mL), forming a cloudy solution. After centrifuging, enriched analytes in the sediment phase were determined by HPLC-UV. The effect of various factors, such as the extraction and dispersive solvent, sample pH, extraction time and salt effect were investigated. Under optimum conditions, enrichment factors for 2-anilinoethanol, o-chloroaniline and 4-bromo-N,N-dimethylaniline were above 50 and the limits of detection (LODs) were 0.023, 0.015 and 0.026 ng/mL, respectively. Their linear ranges were 0.8-400 ng/mL for 2-anilinoethanol, 0.5-200 ng/mL for o-chloroaniline and 0.4-200 ng/mL for 4-bromo-N,N-dimethylaniline, respectively. Relative standard deviations (RSDs) were below 5.0%. The relative recoveries from samples of environmental water were in the range of 82.0-94.0%. Compared with other methods, dispersive liquid-liquid microextraction is simple, rapid, sensitive and economical.     

分散液液微萃取-气相色谱法快速测定水中23种有机磷农药

建立了分散液液微萃取(DLLME)的新型样品前处理方法,并采用气相色谱/火焰光度检测器对饮用水中的治螟磷、甲拌磷、二嗪农、乙拌磷、甲基毒死蜱、甲基对硫磷、皮蝇磷、杀螟松、马拉硫磷、毒死蜱、倍硫磷、对硫磷、溴硫磷、嘧啶磷、甲基异硫磷、稻丰散、杀扑磷、丙溴磷、乙硫磷、三唑磷、三硫磷、哒嗪硫磷、亚胺硫磷23种痕量有机磷农药残...     

Low density miniaturized homogeneous liquid-liquid extraction: a new high throughput sample preparation technique for the determination of polar pesticides in cow milk

The application of miniaturized homogeneous liquid-liquid extraction (MHLLE) technique as a simple, inexpensive, quick and efficiency clean up method has been evaluated for determination of diazinon, alachlor, chlorpyrifos and butachlor in cow milk samples. Methanol was used as extraction solvent for the extraction of analytes from cow milk samples and then, methanol phase was extracted and cleaned up by MHLLE method. In this method, butyl acetate was added to methanol phase and after addition of water, butyl acetate was separated from methanol phase and injected to the GC/TSD instrument. The concentration ranges were from 1.0–1000.0 ng/mL for diazinon and chlorpyrifos and from 5.0–1000.0 ng/mL for alachlor and butachlor. The limits of detection were 0.4, 1.6, 0.3 and 1.4 ng/mL for diazinon, alachlor, chlorpyrifos and butachlor, respectively. Finally, the extraction method was successfully applied to the analysis of raw cow milk samples.     

Determination of phenols in waters by stir membrane liquid-liquid-liquid microextraction coupled to liquid chromatography with ultraviolet detection

A simple and rapid method for the determination of eleven phenols in water samples is presented. The target analytes are isolated by stir membrane liquid-liquid microextraction working under the three-phase mode. An alkaline aqueous solution is used as extractant phase while octanol is selected as supported liquid membrane solvent. The target analytes are separated and determined by liquid chromatography (LC) with ultraviolet detection (UV). All the variables involved in the extraction process have been studied in depth. Low detection limits (in the range from 82.1 ng/L for phenol to 452 ng/L for 2,4,5-trichlorophenol) were obtained. The repeatability, expressed as relative standard deviation (RSD), varied between 1.3% (for 4-nitrophenol) and 8.0% (for 4-chlorophenol). The enrichment factors were in the range from 168 (for 2,4,5-trichlorophenol) to 395 (for 3-chlorophenol). The proposed procedure was applied for the direct determination of the eleven phenols in some real water samples including river, well and tap waters. The accuracy was evaluated by means of a recovery study, the results being in the range of 87-120%.     

Improved solvent collection system for a dispersive liquid-liquid microextraction of organochlorine pesticides from water using low-density organic solvent

In this study, the organochlorine pesticides (OCPs) levels in lake and tap water samples were determined by a dispersive liquid-liquid microextraction method using a low-density organic solvent and an improved solvent collection system (DLLME-ISCS). This method used a very small volume of a solvent of low toxicity (11 μL of 1-nonanol and 400 μL of methanol) to extract OCPs from 10 mL water samples prior to the analysis by GC. After centrifugation in the dispersive liquid-liquid microextraction, there was a liquid organic drop floating between the water surface and the glass wall of the centrifuge tube. The liquid organic drop (with some water phase) was transferred into a microtube (3 mm×15 mm) with a syringe. The organic and aqueous phases were separated in the microtube immediately. Then, 1 μL of the organic solvent (which was in the upper portion of liquid in the microtube) was easily collected by a syringe and injected into the GC-ECD system for the analysis. Under optimum conditions, the linear range of this method was 5-5000 ng/L for most of the analytes. The correlation coefficient was higher than 0.997. Enrichment factors ranged from 1309 to 3629. The relative recoveries ranged from 73 to 119% for lake water samples. The LODs of the method ranged from 0.7 to 9.4 ng/L. The precision of the method ranged from 1.0 to 10.8% for lake water.     

n-Octylated Magnetic Nanoparticle-Based Microextraction for the Determination of Organophosphorus Pesticides in Water

A sensitive and simple procedure based on the dispersive solid phase extraction with hydrophobic n-octyl-modified magnetic iron oxide nanoparticles as the sorbent was developed for the determination of ethoprophos, fenchlorphos, parathion methyl, chlorpyrifos, prothiofos, and azinphos methyl in environmental water samples. Dispersive liquid–liquid microextraction was coupled with dispersive solid-phase microextraction to enhance the dispersibility of the selected sorbent and extraction efficiency. The organophosphorus pesticides were detected using gas chromatography with a flame photometric detector. Under optimized conditions, this method achieved low method detection limit (0.02–0.10 microgram per liter), wide linearity (0.5–800 microgram per liter), high enrichment factors (122–143), good correlation coefficients (r = 0.9975–0.9997), and good repeatability (0.2–7.1 percent). This method was also successfully applied to analyze drinking water and surface water with good extraction efficiency (≥82 percent) and high degree of precision (≤5 percent). The results also indicated that the dispersibility of hydrophobic magnetic nanoparticles was enhanced with liquid–liquid microextraction without chemical modification of the magnetic iron oxide nanoparticles.     

Determination of organophosphorus insecticides in natural waters using SPE-disks and SPME followed by GC/FTD and GC/MS

Two methods for the analysis of ten organophosphorus insecticides in natural waters using solid phase extraction disks containing C18 and SDB and solid phase microextraction fibers containing polyacrylate (PA) are developed. Bromophos ethyl, bromophos methyl, dichlofenthion, ethion, fenamiphos, fenitrothion, fenthion, malathion, parathion ethyl and parathion methyl were determined by GC/MS and GC/FTD. The SPE-disks require only 1000 mL of sample and provide a method limit of detection in the range of 0.01-0.07 microgram/L and recovery rates from 60.7 to 104.1%. The solid phase microextraction (SPME) technique requires 2-5 mL of water sample and provides a method limit of detection in the range of 0.01 to 0.05 microgram/L for all detectors and the recoveries compared to distilled water ranged from 86.2 to 119.7%. The proposed methods were applied to the trace level screening determination of insecticides in river water samples originating from different Greek regions.     

Extraction of pesticides from aqueous samples: A comparative study

Three different extraction procedures for eight pesticides (chlorfenvinphos, diazinon, ethyl parathion, ethiofencarb, fenitrothion, malathion, metalaxyl, pirimicarb) in water samples are compared. The extraction procedures are: liquid-liquid extraction (LLE), solid-phase extraction (SPE) and microextraction (ME). For each procedure the most suitable conditions were obtained experimentally, with special remarks on ME, in which the effects of different mixtures of Kaltron with other solvents were tested. A preconcentration factor (PF) was used to rank the methods; the best results were observed for ME, (PF 15–45, whereas PF < 10 for SPE, and PF 13 for LLE). In all cases, the determination was performed by gas chromatography, using a nitrogen phosphorus detector and the internal standard method (methyl parathion) as the quantification procedure.     

Simple, rapid, and sensitive determination of beta-blockers in environmental water using dispersive liquid-liquid microextraction followed by liquid chromatography with fluorescence detection

A novel method, dispersive liquid-liquid microextraction combined with liquid chromatography-fluorescence detection is proposed for the determination of three beta-blockers (metoprolol, bisoprolol, and betaxolol) in ground water, river water, and bottled mineral water. Some important parameters, such as the kind and volume of extraction and dispersive solvents, extraction time, pH, and salt effect were investigated and optimized. In the method, a suitable mixture of extraction solvent (60 μL carbon tetrachloride) and dispersive solvent (1 mL acetonitrile) were injected into the aqueous samples (5.00 mL) and the cloudy solution was observed. After centrifugation, the enriched analytes in the bottom CCl(4) phase were determined by liquid chromatography with fluorescence detection. Under the optimum conditions, the enrichment factors (EFs) for metoprolol, bisoprolol, and betaxolol were 180, 190, and 182, and the limits of detection (LODs) were 1.8, 1.4, and 1.0 ng L(-1) , respectively. A good linear relationship between the peak area and the concentration of analytes was obtained in the range of 3-150 ng L(-1) . The relative standard deviations (RSDs) for the extraction of 10 ng L(-1) of beta-blockers were in the range of 4.6-5.7% (n = 5). Compared with other methods, dispersive liquid-liquid microextraction is a very simple, rapid, sensitive (low limit of detection), and economical (only 1.06 mL volume of organic solvent) method, which is in compliance with the requirements of green analytical methodologies.     

Measurement of trihalomethanes and methyl tertiary-butyl ether in tap water using solid-phase microextraction GC-MS

The prevalence of water disinfection byproducts in drinking water supplies has raised concerns about possible health effects from chronic exposure to these compounds. To support studies exploring the relation between exposure to trihalomethanes (THMs) and health effects, we have developed an automated analytical method using headspace solid-phase microextraction coupled with capillary gas chromatography and mass spectrometry. This method quantitates trace levels of THMs (chloroform, bromodichloromethane, dibromochloromethane, and bromoform) and methyl tertiary-butyl ether in tap water. Detection limits of less than 100 ng/L for all analytes and linear ranges of three orders of magnitude are adequate for measuring the THMs in tap water samples tested from across the United States. THMs are stable for extended periods in tap water samples after quenching of residual chlorine and buffering to pH 6.5, thus enabling larger epidemiologic field studies with simplified sample collection protocols.     

Temperature‐controlled liquid–liquid microextraction combined with high‐performance liquid chromatography for the simultaneous determination of diazinon and fenitrothion in water and fruit juice samples

A simple, environmentally benign, and rapid method based on temperature‐controlled liquid–liquid microextraction using a deep eutectic solvent was developed for the simultaneous extraction/preconcentration of diazinon and fenitrothion. The method involved the addition of deep eutectic solvent to the aqueous sample followed by heating the mixture in a 75°C water bath until the solvent was completely dissolved in the aqueous phase. Then, the resultant solution was cooled in an ice bath and a cloudy solution was formed. Afterward, the mixture was centrifuged and the enriched deep eutectic solvent phase was analyzed by high‐performance liquid chromatography with ultraviolet detection for quantification of the analytes. The factors affecting the extraction efficiency were optimized. Under the optimized extraction conditions, the limits of detection for diazinon and fenitrothion were 0.3 and 0.15 μg/L, respectively. The calibration curves for diazinon and fenitrothion exhibited linearity in the concentration range of 1–100 and 0.5–100 μg/L, respectively. The relative standard deviations for five replicate measurements at 10.0 μg/L level of analytes were less than 2.8 and 4.5% for intra‐ and interday assays, respectively. The developed method was successfully applied to the determination of diazinon and fenitrothion in water and fruit juice samples.     

Application of pneumatic nebulization single‐drop microextraction for the determination of organophosphorous pesticides by gas chromatography–mass spectrometry

Organophosphorous pesticides (OPPs) including dichlorvos, diazinon, malathion, phenamiphos and chlorpyrifos, in water samples were extracted by pneumatic nebulization single‐drop microextraction (PN‐SDME) and then determined by gas chromatography–mass spectrometry (GC‐MS). Experimental parameters affecting the performances of PN‐SDME, such as flow rate of carrier gas, extraction time and microdrop volume, were examined and optimized. The limits of detection for the analytes were in the range of 0.0014–0.0019 μg/mL. The linear range was 0.0050–0.50 μg/mL, except dichlorvos (0.0070–0.50 μg/mL). Water samples were analyzed and the recoveries of the analytes in the spiked water samples were from 75.2 to 105.3%. The relative standard deviations were lower than 12.7%.     

Ultrapreconcentration and determination of organophosphorus pesticides in water by solid‐phase extraction combined with dispersive liquid–liquid microextraction and high‐performance liquid chromatography

Solid‐phase extraction coupled with dispersive liquid–liquid microextraction was developed as an ultra‐preconcentration method for the determination of four organophosphorus pesticides (isocarbophos, parathion‐methyl, triazophos and fenitrothion) in water samples. The analytes considered in this study were rapidly extracted and concentrated from large volumes of aqueous solutions (100 mL) by solid‐phase extraction coupled with dispersive liquid–liquid microextraction and then analyzed using high performance liquid chromatography. Experimental variables including type and volume of elution solvent, volume and flow rate of sample solution, salt concentration, type and volume of extraction solvent and sample solution pH were investigated for the solid‐phase extraction coupled with dispersive liquid–liquid microextraction with these analytes, and the best results were obtained using methanol as eluent and ethylene chloride as extraction solvent. Under the optimal conditions, an exhaustive extraction for four analytes (recoveries >86.9%) and high enrichment factors were attained. The limits of detection were between 0.021 and 0.15 μg/L. The relative standard deviations for 0.5 μg/L of the pesticides in water were in the range of 1.9–6.8% (n = 5). The proposed strategy offered the advantages of simple operation, high enrichment factor and sensitivity and was successfully applied to the determination of four organophosphorus pesticides in water samples.     

Headspace solid-phase microextraction for the gas chromatographic analysis of organophosphorus insecticides in vegetables

Residues of organophosphorus insecticides (diazinon, methyl parathion, fenitrothion, malathion, and parathion) were determined in 13 different vegetable matrixes by headspace solid-phase microextraction performed with a polydimethyl-siloxane fiber (100 microm). Determination was carried out by gas chromatography with a nitrogen-phosphorus detector. Limits of detection and quantification were < 0.005 and 0.017 mg/kg, respectively; thus, the limits of maximum residue levels (MRLs) required by European regulations can be verified without difficulty. Pesticide residues were found in 38% of the 125 fresh commercial samples (imported and domestic) that were analyzed. Residues of methyl parathion and parathion, which were withdrawn in Greece in 2003, were detected in 36.8 and 4% of all samples, respectively. The MRLs were exceeded overall by 1%.     

Accurate analysis of trace earthy-musty odorants in water by headspace solid phase microextraction gas chromatography-mass spectrometry

A simple and sensitive method was developed for the simultaneous separation and determination of trace earthy-musty compounds including geosmin, 2-methylisoborneol, 2-isobutyl-3-methoxypyrazine, 2-isopropyl-3-methoxypyrazine, 2,3,4-trichloroanisole, 2,4,6-trichloroanisole, and 2,3,6-trichloroanisole in water samples. This method combined headspace solid-phase microextraction (HS-SPME) with gas chromatography-mass spectrometry and used naphthalene-d(8) as internal standard. A divinylbenzene/carboxen/polydimethylsiloxane fiber exposing at 90°C for 30 min provided effective sample enrichment in HS-SPME. These compounds were separated by a DB-1701MS capillary column and detected in selected ion monitoring mode within 12 min. The method showed a good linearity from 1 to 100 ng L(-1) and detection limits within (0.25-0.61 ng L(-1)) for all compounds. Using naphthalene-d(8) as the internal standard, the intra-day relative standard deviation (RSD) was within (2.6-3.4%), while the inter-day RSD was (3.5-4.9%). Good recoveries were obtained for tap water (80.5-90.6%), river water (81.5-92.4%), and lake water (83.5-95.2%) spiked at 10 ng L(-1). Compared with other methods using HS-SPME for determination of odor compounds in water samples, this present method had more analytes, better precision, and recovery. This method was successfully applied for analysis of earthy-musty odors in water samples from different sources.     

Electrospun terpolymeric nanofiber membrane for micro solid‐phase extraction of diazinon and chlorpyrifos from aqueous samples

The present study deals with the synthesis and electrospining of a new terpolymer nanofiber in order to determine the amount of diazinon and chlorpyrifos in water and fruit juice samples. The synthesized terpolymer and the prepared nanofiber were characterized using ¹H NMR spectroscopy, FTIR spectroscopy, scanning electron microscopy, and gel permeation chromatography. The performance of terpolymer nanofiber, prepared as a sorbent for micro solid phase extraction was investigated for the extraction of diazinon and chlorpyrifos from aquaeous media. Then, the target analytes were desorbed from the coating with an organic solvent and analyzed by gas chromatography with flame ionization detector. Extraction efficiencies were significant (>90%) under the optimum condition. The proposed method also demonstrated good linear dynamic ranges for diazinon and chlorpyrifos (3–250 and 5–200 µg/L), and low limit of detections (0.5 and 0.7 µg/L) respectively. Moreover, under optimum condition for extraction of diazinon and chlorpyrifos, square of correlation coefficients (R²) of 0.9978 and 0.9953 and relative standard deviations of 4.6 and 5.1% were achieved, respectively. The recoveries for diazinon and chlorpyrifos were in the range of 85–97%.     

QuEChERS Technique for the Gas Chromatographic Determination of Organophosphate Residues in Strawberries

This study describes the validation of an analytical method employing gas chromatography with flame photometric detection for the determination of organophosphate pesticides (diazinon, disulfoton, parathion, chlorpyrifos, and malathion) in strawberries. The method employed a QuEChERS dispersive solid phase extraction for the sample preparation. QuEchERS is inexpensive, fast, and easy for the separation of the analytes from the matrix. In addition, the method provided linear calibration curves, ranging from 0.10–1.00 µg g^?1, for diazinon, disulfoton, parathion, and chlorpyrifos, and 0.10–2.00 µg g^?1 for malathion. Recovery studies yielded values in the range from 81.64 to 100.00%. These results demonstrated the potential of the technique for the determination of organophosphate residues in strawberries.