Characterization of Y<Subscript>2</Subscript>BaCuO<Subscript>5</Subscript> nanoparticles synthesized by nano-emulsion method

Nanoscale yttrium–barium–copper oxide (Y₂BaCuO₅, Y211) particles were synthesized using the emulsion method and the solution method. The basic water-in-oil (w/o) emulsion system consisted of n-octane (continuous oil phase), cetyltrimethylammonium bromide (cationic surfactant), butanol (cosurfactant) and water. The composition of the emulsion system was varied and characterized by measuring the conductivity of the solutions and droplet size. The droplet size of emulsion was determined by using the dynamic light scattering method. The water content, cosurfactant content, and surfactant/n-octane ratio affected the droplet size which was in the range of 3–8 nm, and hence the w/o emulsion system was referred to as a nano-emulsion system. A model was used to verify the droplet size. The influence of salt (Y₂(NO₃)₃) content on the droplet size was investigated and the addition of salt reduced the droplet size. The effects of reaction time and temperature on the Y211 particle sizes were also investigated. The particles were characterized using the TEM, SEM, and XRD. Nanoparticles produced by the nano-emulsion method were calcined at 850°C to form the Y211 phase as compared to solid state processing temperature of 1050°C. Based on the TEM analysis, the average diameter of the Y211 particles produced using the nano-emulsion method was in the range of 30–100 nm. The effect of adding 15% Y211 nanoparticles to the superconductor YBCO-123 as flux pinning centers, was investigated, and the transition temperature was reduced by 3 K.     

Controlled synthesis of photoluminescent Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> nanoparticles from metal-organic polymeric precursor

Bi₄Ti₃O₁₂ (BIT) nanoparticles with a narrow average particle size distribution in the range of 11–46 nm was synthesized via a metal-organic polymeric precursor process. The crystallite size and lattice parameter of BIT were determined by XRD analysis. At annealing temperatures >550 °C, the orthorhombic BIT compound with lattice parameters a = 5.4489 Å, b = 5.4147 Å, and c = 32.8362 Å was formed while at lower annealing temperatures orthorhombicity was absent. Reaction proceeded via the formation of an intermediate phase at 500 °C with a stoichiometry close to Bi₂Ti₂O₇. The particle size and the agglomerates of the primary particles have been confirmed by FESEM and TEM. The decomposition of the polymeric gel was ascertained in order to evaluate the crystallization process from TG-DSC analysis. Raman spectroscopy was used to investigate the lattice dynamics in BIT nanoparticles. In addition, investigation of the dependence of the visible emission band around the blue–green color emission on annealing temperatures and grain sizes showed that the effect of grain size plays important roles, and that oxygen vacancies may act as the radiative centers responsible for the observed visible emission band.     

Synthesis,characterization, and thermal stability of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript>/CR-Ag multilayered nanostructures

The controllable synthesis and characterization of novel thermally stable silver-based particles are described. The experimental approach involves the design of thermally stable nanostructures by the deposition of an interfacial thick, active titania layer between the primary substrate (SiO₂ particles) and the metal nanoparticles (Ag NPs), as well as the doping of Ag nanoparticles with an organic molecule (Congo Red, CR). The nanostructured particles were composed of a 330-nm silica core capped by a granular titania layer (10 to 13 nm in thickness), along with monodisperse 5 to 30 nm CR-Ag NPs deposited on top. The titania-coated support (SiO₂/TiO₂ particles) was shown to be chemically and thermally stable and promoted the nucleation and anchoring of CR-Ag NPs, which prevented the sintering of CR-Ag NPs when the structure was exposed to high temperatures. The thermal stability of the silver composites was examined by scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). Larger than 10 nm CR-Ag NPs were thermally stable up to 300 °C. Such temperature was high enough to destabilize the CR-Ag NPs due to the melting point of the CR. On the other hand, smaller than 10 nm Ag NPs were stable at temperatures up to 500 °C because of the strong metal-metal oxide binding energy. Energy dispersion X-ray spectroscopy (EDS) was carried out to qualitatively analyze the chemical stability of the structure at different temperatures which confirmed the stability of the structure and the existence of silver NPs at temperatures up to 500 °C.     

Comparison of Eu(NO<Subscript>3</Subscript>)<Subscript>3</Subscript> and Eu(acac)<Subscript>3</Subscript> precursors for doping luminescent silica nanoparticles

In this study, we report the comparison between Eu³⁺-doped silica nanoparticles synthesized by Stöber method using Eu(NO₃)₃ or Eu(acac)₃ as precursors. The impact of different europium species on the properties of the final silica nanospheres is investigated in details in terms of size, morphology, reachable doping amount, and luminescence efficiency. Moreover, the results obtained for different thermal treatments are presented and discussed. It is shown that the organic complex modify the silica growing process, leading to bigger and irregular nanoparticles (500–800 nm) with respect to the perfectly spherical ones (400 nm) obtained by the nitrate salt, but their luminescence intensity and lifetime is significantly higher when 800–900 °C annealing is performed.     

Preparation of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials by electrospinning

LiNi_0.5Mn_1.5O₄ cathode material was prepared by electrospinning using lithium hydroxide, manganese acetate, nickel acetate, acetic acid, ethanol, and poly(vinyl pyrrolidone) as raw materials. The effect of calcination temperature on the structure, morphology, and electrochemical properties was investigated. XRD results indicate that the LiNi_0.5Mn_1.5O₄ composite is well crystallized as a spinel structure at calcination temperature of 650 °C for 3 h. SEM results reveal that this composite has a nanofiber shape with average size of about 300–500 nm. Electrochemical performance tests reveal that this composite shows the initial discharge capacity of 127.8 and 105 mAhg^?1 at 0.1 and 3 C rates, respectively, and exhibits good cycling performance.     

Generation of MoS<Subscript>2</Subscript> quantum dots by laser ablation of MoS<Subscript>2</Subscript> particles in suspension and their photocatalytic activity for H<Subscript>2</Subscript> generation

MoS₂ quantum dots (QDs) have been obtained in colloidal suspensions by 532 nm laser ablation (7 ns fwhp/pulse, 50 mJ/pulse) of commercial MoS₂ particles in acetonitrile. High-resolution transmission electron microscopy images show a lateral size distribution from 5 to 20 nm, but a more homogeneous particle size of 20 nm can be obtained by silica gel chromatography purification in acetonitrile. MoS₂ QDs obtained by laser ablation are constituted by 3–6 MoS₂ layers (1.8–4 nm thickness) and exhibit photoluminescence whose λ_PL varies from 430 to 530 nm depending on the excitation wavelength. As predicted by theory, the confinement effect and the larger periphery in MoS₂ QDs increasing the bandgap and having catalytically active edges are reflected in an enhancement of the photocatalytic activity for H₂ generation upon UV–Vis irradiation using CH₃OH as sacrificial electron donor due to the increase in the reduction potential of conduction band electrons and the electron transfer kinetics.     

An investigation on the unsatisfactory rate capability of spherical LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> particles prepared by using Na<Subscript>2</Subscript>CO<Subscript>3</Subscript> as a precipitant

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ particles were successfully synthesized using Na₂CO₃ as a precipitant. Electrochemical measurements indicate that the as-synthesized spherical particles deliver a high reversible capacity of above 180 mAh g^?1 at 0.1 C in the voltage range of 2.8–4.4 V and display an excellent cyclic performance at 0.5 C. However, unsatisfactory rate capability was detected for the as-prepared spherical particles. The reason for the unsatisfactory rate capability was investigated through a comparison of the properties of the as-synthesized spherical particles versus the ball-milled samples via a combination of specific surface areas test, electronic conductivity measurement, and electrochemical impedance spectroscopy. The results show that both the rate capabilities of cathode materials and the electronic conductivities of the mixtures of active material, conductive additive, and binder are highly improved when the secondary spherical particles were broken, indicating that the poor electronic conductivity of electrode caused by the large secondary spherical particles with a great amount of nano-pores is a significant factor for the unsatisfactory rate capability.     

Synthesis,thermal and electrical behavior of the superprotonic conductor phase in Rb<Subscript>3</Subscript>(HSeO<Subscript>4</Subscript>)<Subscript>2.5</Subscript>(H<Subscript>2</Subscript>PO<Subscript>4</Subscript>)<Subscript>0.5</Subscript> compound

The Rb₃(HSeO₄)_2.5(H₂PO₄)_0.5 compound was prepared and its thermal behavior and electric properties were investigated. The thermogravimetry (TGA) analysis and the differential scanning calorimetric (DSC) show the presence of a structural phase transition of the title compounds at 374 K which is confirmed by the variation of fp and σ_dc as a function of temperature. The complex impedance of the Rb₃(HSeO₄)_2.5(H₂PO₄)_0.5 compound has been investigated in the temperature range of 295–453 K and in the frequency range 209 Hz–1 MHz. The impedance plots show semicircle arcs at different temperatures, and an electrical equivalent circuit has been proposed to explain the impedance results. The circuits consist of the parallel combination of bulk resistance Rp and constant phase elements CPE₁ in series with fractal capacity CPE₂. The frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. The conductivity dc follows the Arrhenius relation. The near value of activation energies obtained from the analysis of modulus, conductivity data, and circuit equivalent confirm that the transport is through the ion hopping mechanism, dominated by the motion of the H⁺ proton in the structure of the investigated materials.     

The enhanced catalytic degradation of SiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/C@TiO<Subscript>2</Subscript> photo-Fenton system on p-nitrophenol

Heterogeneous photo-Fenton SiO₂/Fe₃O₄/C@TiO₂ (SFCT) catalyst with a core-multishell structure and a diameter of about 550 nm was successfully prepared and was characterized by scanning electron microscopy (SEM), TEM, XRD, Raman, and Fourier transform infrared (FT-IR). The results illustrated that anatase TiO₂ coexisted with rutile TiO₂, in which the anatase phase was the main crystal phase. In addition, the catalytic activity of SFCT catalyst had been evaluated in the catalytic degradation on p-nitrophenol (PNP). The influence factors on the PNP degradation, including SFCT component ratio (m _SFC/ m _TiO2), H₂O₂ dosage, solution pH, and PNP concentration, had been investigated. And the contrast experiments about the photo-Fenton catalytic mechanism revealed that the SFCT-2 catalyst possessed a superior activity in the neutral environment due to the optimal activity matching between Fe₃O₄ and TiO₂, and it exhibited the stable catalytic performance after five successive recycles. Therefore, the SFCT-2 catalyst had a promising application for the photo-Fenton degradation of organic contaminant.     

Nanoparticulate BaTiO<Subscript>3</Subscript> film produced by aerosol-type nanoparticle deposition

Aerosol-type nanoparticle deposition (NPD) is a magical method to form a dense electroceramic film with a fine, nanoscale structure on a substrate surface by depositing ceramic particles through a nozzle at room temperature. This film has the potential to be applied to various electronic, environmental, and energy devices. However, the deposition mechanism and the nanostructure in the film are not understood sufficiently. This study aimed at investigating the crystal structure of an NPD as-deposited film, and compared the crystal structures of the NPD as-deposited film, annealed film, and the raw powders consisting of particles with diameters of 200 and 50 nm, respectively, using barium titanium oxide (BaTiO₃). We found that the crystal in BaTiO₃ with a disordered phase due to the Ba displacement within the BaTiO₃ was responsible for the adhesion between the BaTiO₃ crystalline particles having a diameter of approximately 10 nm, as well as with the substrate.     

Acacia gum-assisted co-precipitating synthesis of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion batteries

LiNi_0.5Co_0.2Mn_0.3O₂ particles of uniform size were prepared through carbonate co-precipitation method with acacia gum. The precursor of carbonate mixture was calcined at 800 °C, and a well-crystallized Ni-rich layered oxide was got. The phase structure and morphology were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The micro-sized particles delivered high initial discharge capacity of 164.3 mA h g^?1 at 0.5 C (1 C?=?200 mA g^?1) between 2.5 and 4.3 V with capacity retention of 87.5 % after 100 cycles. High reversible discharge capacities of 172.4 and 131.4 mA h g^?1 were obtained at current density of 0.1 and 5 C, respectively. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were performed to further study the LiNi_0.5Co_0.2Mn_0.3O₂ particles. Anyway, the excellent electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ sample should be attributed to the use of acacia gum.     

Facile synthesis of near-infrared CuInS<Subscript>2</Subscript>/ZnS quantum dots and glycol-chitosan coating for in vivo imaging

This study describes the synthesis method of water-soluble, low-toxicity, photostable highly luminescent probes based on I–III–VI₂ type semiconductor quantum dots (QDs) and the possibility of tumor targeting in living animals. Cd-free high-quality CuInS₂/ZnS core/shell QDs were synthesized, and their surfaces were reacted with mercaptoundecanoic acid for aqueous phase transfer followed by reaction with glycol-chitosan; lastly, Arg-Gly-Asp (RGD) integrin-binding peptide was covalently attached for in vivo tumor targeting. Dowtherm A, a highly viscous heat-transfer organic fluid, was used to control semiconductor crystal growth at high temperature (>230 °C) during organic synthesis. The structural and optical properties of the resulting CuInS₂/ZnS QDs were investigated. The average diameters of CuInS₂ and CuInS₂/ZnS QDs were 3.0 and 3.7 nm, respectively. Cell toxicity and in vivo tumor targetability in RR1022 cancer cell-xenografted mice were further evaluated using cRGDyk-tagged glycol-chitosan-coated CuInS₂/ZnS QDs. Glycol-chitosan-coated MUA-QDs displayed a Z-average diameter of 203.8 ± 7.67 nm in water by dynamic light scattering.

Open image in new window

Graphical abstract In vivo tumor targeting using cRGDyk-tagged glycol-chitosan-coated MUA-CuInS₂/ZnS QDs nanoparticles

     

Engineering coercivity in YFe<Subscript>2</Subscript> dominated DyFe<Subscript>2</Subscript>/YFe<Subscript>2</Subscript> superlattice by patterning

Single crystal 400 nm thick Laves phase [20 Å?DyFe₂/80 Å?YFe₂]₄₀ superlattice have been grown by MBE with a (110) growth direction. VSM measurements performed at room temperature with an applied field range of ±1.2×10⁵ Oe, directed along the [001] direction, reveal a unique single-phase-liked ferrimagnetic behavior. A dominant exchange spring behavior is revealed by MOKE measurement along the [–110] direction. Furthermore, for striped arrays patterned along the [001] direction with height-to-width ratio of 0.05, a shape anisotropy of the order of 10⁴ erg/cm³ is induced, resulting into a pronounced change of coercivity due to the comparable magnitude with intrinsic anisotropies. The results demonstrate the feasibility of engineering both single-phase-liked and exchange-spring magnet behavior in Laves phase epitaxial hard/soft superlattices by patterning.     

Fe<Subscript>3</Subscript>P impurity phase in high-quality LiFePO<Subscript>4</Subscript>: X-ray diffraction and neutron-graphical studies

High discharge capacity and long life cycles of electrodes fabricated from various LiFePO₄ powders have been used to select samples for detailed structural studies. In some samples, the presence of ferromagnetic Fe₃P crystallites was revealed by the synchrotron X-ray diffraction analysis, with the integral intensity ratio of the peaks Fe₃P (231) and LiFePO₄ (112) equal to ～1/12. Small-angle polarized neutron scattering (SAPNS) detected the presence of magnetic nuclear contrasting regions with size of 17 ± 1 nm. The average diameter of LiFePO₄ crystallites is 230 nm, and Fe₃P crystallites were found as 17 × 54 nm² plates. The high quality of these samples was provided by their manufacturer via synthesis of the Fe₃P impurity phase. It can be stated that the set of studies, developed in the study, is helpful in a search for new effective impurity phases and in optimization of their parameters.     

Synthesis,crystal structure,Hirshfeld surface analysis,and vibrational and DFT investigation of [C<Subscript>6</Subscript>H<Subscript>10</Subscript>(NH<Subscript>3</Subscript>)<Subscript>2</Subscript>]<Subscript>3</Subscript>CuBr<Subscript>4</Subscript>.3Br

Single crystal of a new organic–inorganic hybrid material [C₆H₁₀(NH₃)₂]₃CuBr₄.3Br was synthesized by the slow evaporation method at room temperature and characterized by X-ray diffraction, FTIR, Raman spectroscopy, UV–Vis, dielectric measurements, and Hirschfield surface analysis. The title compound crystallizes in trigonal system \( P\overline{3} \).The crystal packing is governed by the N-H…Br and non-classical C-H…Br hydrogen-bonding interactions between the 1, 2-diamoniumcyclohexane cations, the tetrahedral [CuBr₄]^3? anions, and the isolated ion Br^?. Theoretical calculations were performed using density functional theory (DFT) for studying the molecular structure, vibrational spectra, and optical properties of the investigated molecule in the ground state. The optimized geometrical parameters obtained by DFT calculations are in good agreement with single crystal XRD data. The optical properties were investigated by optical absorption and show two bands at 260 and 305 nm.     

Photocatalytic ability of Bi<Subscript>6</Subscript>Ti<Subscript>3</Subscript>WO<Subscript>18</Subscript> nanoparticles with a mix-layered Aurivillius structure

Aurivillius phase layered perovskites Bi₆Ti₃WO₁₈ was prepared by the sol-gel citrate-complexation synthesis. The sample developed into the plate-like nanoparticles with the exposed (001) facets. The phase formation and structure have been verified via X-ray polycrystalline powder diffraction (XRD) Rietveld refinements. The nanoparticles were investigated via the measurements such as FE-SEM, TEM, EDS, and the surface analyses. UV–Vis absorption data revealed that the Aurivillius compound has a direct band characteristic with the band energy of 2.214 eV. The band structure of Bi₆Ti₃WO₁₈ nanoparticles was discussed on the base of the experiments and theoretical calculation. Bi³⁺-containing Aurivillius Bi₆Ti₃WO₁₈ shows efficient photocatalytic degradation for rhodamine B dye (RhB) with the visible light irradiation (λ?>?420 nm). Dynamic characteristic of the light-created excitons was measured by the luminescence and decay lifetime. The multivalent properties of W and Ti ions in the Aurivillius-like lattices of Bi₆Ti₃WO₁₈ photocatalyst were discussed.     

Synthesis and microstructure of Co/Ni: MgGa<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

This report discusses the preparation and microstructure of Co/Ni co-doped MgGa₂O₄ nanoparticles. The nanoparticles with the size of 20–55 nm were synthesized by sol-gel method. The phase and crystallinity were confirmed by X-ray powder diffraction (XRD) pattern. The particle size was estimated according to XRD data and transmission electron microscopy. The electronic structure was studied using X-ray photoelectron spectroscopy (XPS). The XPS studies showed that Ga³⁺ ions possess tetrahedral and octahedral sites of spinel structure and the inverse degree (two times of the fraction of tetrahedral Ga³⁺ ions) has increased with the increase of the doping concentration of Co²⁺ and Ni²⁺ ions. For Co/Ni co-doped MgGa₂O₄, two broad absorption bands of 350~500 and 550~700 nm were observed in the absorption spectra. The broad band at 350~500 nm was assigned to the combination of the absorption of octahedral Co²⁺ and Ni²⁺ ions, whereas the absorption band at 550~700 nm is mainly due to tetrahedrally coordinated Co²⁺ ions and octahedrally coordinated Ni²⁺ ions.     

Synthesis and electrochemical properties of Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode material for lithium-ion battery

The layered Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ lithium-rich manganese-based solid solution cathode material has been synthesized by a simple solid-state method. The as-prepared material has a typical layered structure with R-3m and C2/m space group. The synthesized Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has an irregular shape with the size range from 200 to 500 nm, and the primary particle of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has regular sphere morphology with a diameter of 320 nm. Electrochemical performances also have been investigated. The results show that the cathode material Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ prepared at 900 °C for 12 h has a good electrochemical performance, which can deliver a high initial discharge capacity of 233.5, 214.2, 199.3, and 168.1 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. After 50 cycles, the capacity retains 178.0, 166.3, 162.1, and 155.9 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. The results indicate that the simple method has a great potential in synthesizing manganese-based cathode materials for Li-ion batteries.     

Nanocrystalline Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> electrodes for supercapattery application

Nanocrystalline Li₂TiO₃ was successfully synthesized using solid-state reaction method. The microstructural and electrochemical properties of the prepared material are systematically characterized. The X-ray diffraction pattern of the prepared material exhibits predominant (002) orientation related to the monoclinic structure with C2/c space group. HRTEM images and SAED analysis reveal the well-developed nanostructured particles with average size of ～40 nm. The electrochemical properties of the prepared sample are carried out using cyclic voltammetry (CV) and chronopotentiometry (CP) using Pt//Li₂TiO₃ cell in 1 mol L^?1 Li₂SO₄ aqueous electrolyte. The Li₂TiO₃ electrode exhibits a specific discharge capacity of 122 mAh g^?1; it can be used as anode in Li battery within the potential window 0.0–1.0 V, while investigated as a supercapacitor electrode, it delivers a specific capacitance of 317 F g^?1 at a current density of 1 mA g^?1 within the potential range ?0.4 to +0.4 V. The demonstration of both anodic and supercapacitor behavior concludes that the nanocrystalline Li₂TiO₃ is a suitable electrode material for supercapattery application.     

High-temperature complex impedance and modulus spectroscopic studies of doped Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>-BaTiO<Subscript>3</Subscript> ferroelectric ceramics

Lead-free Na_0.5Bi_0.5TiO₃ (NBT) and (1 ? x)Na_0.5Bi_0.5TiO₃ + xBaTiO₃ with x = 0.1 and 0.2 (where x = 0.1 and 0.2 are named as NBT1 and NBT2, respectively), (1 ? y)Na_0.5Bi_0.5TiO₃ + yBa_0.925Nd_0.05TiO₃ with y = 0.1 and 0.2 (where y = 0.1 and 0.2 are named as NBT3 and NBT4, respectively)-based relaxor ferroelectric ceramics were prepared using the sol-gel method. The crystal structure was investigated by X-ray diffraction (XRD) at room temperature (RT). The XRD patterns confirmed the presence of the rhombohedral phase in all the samples. The electrical properties of the present NBT-based samples were investigated by complex impedance and the modulus spectroscopy technique in the temperature range of RT–600 °C. The AC conductivity was found to increase with the substitution of Ba²⁺ ions to the NBT sample whereas it significantly decreased with the addition of Nd³⁺ ions. The more anion vacancies in Ba-added samples and the lower anion vacancies in Nd-added samples were found to be responsible for higher and lower conductivities, respectively.