大尺寸SiO2大孔材料固定化漆酶

以表面固定Cu2+的改性大尺寸SiO2大孔材料作为载体,考察了时间、pH和给酶量对漆酶固定化效果的影响,并对固定化漆酶的活性和稳定性进行了研究。结果表明:5 h时吸附达到平衡,pH为4.5、漆酶与载体比例为5 mg·g-1时固定化效果最好,酶活回收率可达到100.4%;固定化漆酶的最适pH和最适温度较游离漆酶的均有升高且范围变宽,固定化后,漆酶的pH稳定性和热稳定性都得到显著提高;固定化漆酶的K m值略高于游离漆酶的;固定化漆酶具有良好的操作稳定性,与底物反应反复操作10批次后剩余酶活为72.7%。     

磁性壳聚糖微球用于酶的固定化研究：Ⅲ磁性壳聚糖微球的活化及其对脲酶的固化研究

以环氧氯丙烷活化的磁性壳聚糖微球作为载体、对脲酶进行固定化研究,结果表明,在25℃时,活化磁性壳聚糖微球对脲酶的固定化在2h时就达到了最大值,固定化酶和自由酶的最适温度都在65℃左右,自由酶和固定化酶的米氏常数Km值分别为0．042mol/L和0．008mol/L,固定化酶的Km降低了5倍。     

利用壳聚糖的絮凝性质包埋酶的葡萄糖氧化酶电极

本文利用壳聚糖的絮凝性质，将葡萄糖氧化酶包埋在壳聚糖与多聚磷酸盐的絮絮沉淀中，操作简单，固定化效率高。研究了适合了酶电极使用的最佳固定化条件。     

磁性壳聚糖的制备及在脂肪酶固定的应用

采用共沉淀法制备磁性壳聚糖微球,戊二醛做交联剂把脂肪酶固定在磁性壳聚糖载体上,分别使用扫描电子显微镜、傅立叶红外光谱仪、X射线衍射仪、振动样品磁强计、热重分析仪等对磁性壳聚糖微球进行表征分析,并检测了固定化酶的特性.结果表明,制备的磁性壳聚糖性能良好,与游离酶相比,固定化酶的最适p H,最适温度均有提高,固定化酶的热稳定性,对变性剂的耐受力,重复使用性都有较大幅度提高.     

壳聚糖固定L-天门冬酰胺酶的研究

研究了以壳聚糖为载体，戊二醛为交联剂，固定化Ｌ－天门冬酰胺酶的最适条件，并对固定化天门冬酰胺酶的理化性质进行了初步探讨。分别从不同固定化程序、缓冲液及保护剂等方面进行了固定化天门冬酰胺酶的条件优化；固定化酶的活力回收可达２０％左右。固定化酶的最适范围变宽，由游离酶的最适ｐＨ＝４～６变为ｐＨ＝６～１０。连续使用６次后仍可基本维持固定化酶的活力。固定化酶对胃蛋白酶的水解性也较游离酶大大提高。     

大尺寸SiO2大孔材料固定化漆酶

以表面固定Cu²⁺的改性大尺寸SiO₂大孔材料作为载体, 考察了时间、pH和给酶量对漆酶固定化效果的影响, 并对固定化漆酶的活性和稳定性进行了研究。结果表明:5 h时吸附达到平衡, pH为4.5、漆酶与载体比例为5 mg·g^-1时固定化效果最好, 酶活回收率可达到100.4%;固定化漆酶的最适pH和最适温度较游离漆酶的均有升高且范围变宽, 固定化后, 漆酶的pH稳定性和热稳定性都得到显著提高;固定化漆酶的K_m值略高于游离漆酶的;固定化漆酶具有良好的操作稳定性, 与底物反应反复操作10批次后剩余酶活为72.7%。     

壳聚糖微球固定化L-天门冬酰胺酶研究

以反相悬浮交联法合成了壳聚糖微球,并将其应用于固定化L-天门冬酰胺酶。探讨了不同合成条件对成球情况的影响,研究了固定化酶的性质。结果表明,壳聚糖载体可以较好地吸附L-天门冬酰胺酶。固定化酶的活力回收率较高,且稳定性得到提高。     

壳聚糖与丙烯腈接枝共聚物的制备及固定化α-淀粉酶研究

本文以过硫酸钾/亚硫酸氢钠为引发体系,制备了丙烯腈接枝壳聚糖的共聚物,并以 其为载体固定化α-淀粉酶,探讨了固定化酶的最佳制备条件和固定化酶的性质,并与游离 酶、壳聚糖作为载体的固定化α-淀粉酶进行了比较,结果表明,丙烯腈接枝壳聚糖共聚物 是固定化α-淀粉酶的优良载体。     

甲醛活化壳聚糖制备固定化l—天冬酰胺酶

研究了以甲醛活化的壳聚糖为载体固定化ｌ－天冬酰胺酶，其活力回收可达到１１３％，比用以戊二醛为交联剂进行固定化的活力回收要高出五倍多。分别从缓冲液的ｐＨ值及甲醛用量等方面进行了固定化ｌ－天冬酰胺酶的条件优化，并且对固定化酶的性质作了探讨。     

壳聚糖与丙烯腈接枝共聚物的制备及固定化a—淀粉酶研究

主以过硫酸钾／亚硫酸氢钠为引发体系,制备了丙烯腈接枝壳聚糖的共聚物,并以其载体固定化a-淀粉酶,探讨了固定化酶的最佳制备条件和固定化酶的性质,并与游离酶、壳聚糖作为载体的固定化a-淀粉酶进行了比较,结果表明,丙烯腈接枝壳聚糖共聚物是固定化a-淀粉酶的优良载体。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。