低浓度部分水解聚丙烯酰胺/柠檬酸铝交联体系剪切稳定性研究

采用粘度法、核孔膜过滤和动态光散射(DLS)法,研究了高分子量低浓度的部分水解聚丙烯酰胺(HPAM)与柠檬酸铝(AlCit)反应所形成的交联体系的剪切稳定性和HPAM剪切降解后与AlCit反应所形成的体系的封堵性能及降解机理.研究结果表明,低浓度的HPAM与AlCit反应所形成的交联聚合物体系随剪切速率增加,其对1.2μm的核孔膜的封堵能力降低.HPAM稀溶液剪切降解后再与AlCit反应,低剪切速率对其封堵性能影响较小,而高剪切速率会使得其封堵性能大大降低.HPAM/AlCit交联体系和HPAM剪切降解后形成的交联体系的封堵性能下降的原因是HPAM/AlCit交联体系中交联聚合物线团(LPC)尺寸和HPAM中高分子线团的尺寸变小.     

低浓度HPAM/AlCit交联聚合物溶液性质研究

采用粘度法、扫描电镜（SEM）、核孔膜过滤、动态光散射（DLS）和27Al NMR法，研究了高分子量低浓度的部分水解聚丙烯酰胺（HPAM）与柠檬酸铝（AlCit）体系交联反应过程溶液性质变化.结果表明，HPAM与AlCit反应在低剪切速率时体系粘度随反应进行而降低，在剪切速率较高时具有剪切稠化现象，HPAM与AlCit反应过程中交联态Al的自旋 晶格弛豫时间随反应进行变短.低浓度的HPAM与AlCit发生分子内交联反应形成交联聚合物线团（LPC）在水中的分散体系，即交联聚合物溶液（LPS）.交联聚合物溶液中LPC的平均流体力学半径约为238 nm，其形态接近球形，具有多分散性. LPS对1.2 μm核孔膜的封堵程度与其反应时间有关.     

疏水缔合效应对聚丙烯酰胺类水溶液结构和流变性质的影响

以聚合物驱油为背景,研究了部分水解聚丙烯酰胺(HPAM)和缔合型部分水解聚丙烯酰胺(AHPAM)水溶液的结构与流变性质的差别.通过粘度法和静态激光光散射法得到了所分析的聚丙烯酰胺的分子量,用动态激光光散射法和粘度法分析了特定AHPAM分子缔合形态,并用流变学法测定了AHPAM在地层温度与矿化度条件下的线性粘弹性与非线性流变特性.着重讨论了临界缔合浓度的概念,研究了结构和流变性质的关系,以及分析了缔合对聚合物驱油的可能影响.实验结果表明,AHPAM水溶液在宽浓度范围存在分子缔合;一般临界缔合浓度的概念实际反映在进入亚浓溶液范围分子间缔合的效应,剪切速率约为10 s-1时,剪切粘度突降数倍,反映缔合结构在剪切场中的变化,该现象在高缠结浓度下较不明显;拉伸粘度随拉伸速率变化与HPAM定性不同,该拉伸特性反映了疏水缔合近程作用的本质.     

Transportation characteristics of HPAM solution in the micro-fractures

In order to improve the success rate of practical application of an organic polymer conformance control agent in a fractured low permeability reservoir, the transportation characteristics of hydrolyzed polyacrylamide (HPAM) solution in micro-fracture is systematically studied by displacement experiments using the visual model and fractured cores. The results are as follows: (1)There is no threshold pressure for HPAM solution transportation in micro-fracture, and its flow is linear at a certain range of flow rate. (2) There is an appropriate corresponding range between the viscosity of HPAM solution and fracture permeability, which can provide guidance for screening out the appropriate molecular weight or concentration to obey the permeability. (3)Flow resistance of HPAM solution in the micro-fracture is lower than that in porous media at the same water phase permeability, but the difference degree of flow resistance is reduced with the increase of permeability. (4)When the aperture of the lower permeability fractured core in the parallel combination is high, the shunt flow volume of HPAM solution is linear. When the aperture is low, the shunt flow volume is nonlinear. The experimental results can provide important guidance for optimization and application of the polymer conformance control agent in a fractured low permeability reservoir.     

超高分子量聚苯乙烯的流变性能

以毛细管流变仪和Hakke转矩流变仪对稀土催化合成的超高分子量聚苯乙烯 (UHMWPS)的流变与加工性能进行了研究 .结果表明 ,UHMWPS最显著的流变特征为超高的熔体粘度和低剪切速率下出现不稳定流动 .不稳定流动与超高分子量聚合物长的松弛时间有关 ,并提出了临界剪切速率与分子量和温度的定量关系式 .较低的分子量和较高的温度有利于提高临界剪切速率 ,改善挤出物外观质量和降低熔体粘度 .分子链极度缠结不仅导致超高的熔体粘度 ,也使UHMWPS链解缠加快 ,导致更高的剪切速率敏感性 .UHMWPS塑化时熔体粘度高 ,转矩大 ,加工性能劣于通用聚苯乙烯 (GPPS)     

表面活性剂与聚丙烯酰胺在油水界面的流变性

界面流变学是研究界面膜在外力作用下流动与形变的科学，界面粘度是油水界面膜的一种重要性质，它的大小与成股分子排列的紧密程度、成膜分子相互作用力的大小和是否有结构形成有关［‘1，人们早就对表面流变性质进行了相当系统而深入的研究［’41，但是有关油水界面流变性质的     

Effect of molecular structure on polyethylene melt rheology. I. Low-shear behavior

The melt rheological properties of both linear and branched polyethylene were investigated by use of narrow molecular weight distribution fractions and experimentally polymerized samples. Studies carried out in steady shear and in oscillatory shear yielded information concerning both the melt viscosity and the melt elasticity as a function of molecular structure, where the latter was characterized by various solution property techniques. The 3.4–3.5 power dependence of the low shear limiting viscosity on molecular weight was confirmed for linear polyethylene. The effect of long-chain branching on rheological properties was defined both at constant molecular weight and at constant molecular weight distribution and coupled with variation of molecular weight.     

茂金属聚乙烯和低密度聚乙烯共混物的流变行为

研究了茂金属催化乙烯丁烯1共聚物mPE和LDPE共混物的流变行为.测定了一系列共混物的稳态剪切粘度和动态粘弹性,用改进Cross模型拟合实验数据.mPE的零切粘度η₀较小,从牛顿型转变为非牛顿型所需的剪切速率较大,转变应力较高,在挤出加工剪切速率范围内熔体粘度高,对剪切敏感性差,这是由于它有较低的重均分子量、窄的分子量分布(M_w/M_n=21)所致.对于对数加和规律,共混物η₀在mPE/LDPE为50/50和25/75时有强烈的正偏差,这是由于共混物自由体积减小所致.共混物的转变应力τ^*和非牛顿指数n随LDPE加入量增大而降低,表明共混物对剪切的敏感性提高,加工性得到改善.G'和G”的一致性说明mPE和LDPE共混是相容的.     

纳米SiO2/HPAM/NaCl分散体系的稳定性、流变性及驱油性能研究

利用纳米粒度及Zeta电位分析仪、流变仪和悬滴法对纳米SiO_2/HPAM/NaCl体系60℃的稳定性、流变性及油水界面张力进行了研究。结果表明,HPAM的加入使SiO_2悬浮液的Zeta电位更负、粒径明显增加,静置10 d无明显浑浊现象。加入纳米SiO_2后,HPAM溶液的黏度增加,耐温、耐盐和耐剪切性能得到改善。对于质量分数为0.18%的HPAM溶液,SiO_2质量分数小于0.5%时,随SiO_2质量分数的增加,体系的黏度、储能模量和损耗模量增加,临界线性应变减小,蠕变回复能力增强;SiO_2质量分数大于0.5%时,出现了相反的现象;这是因为SiO_2质量分数不同时,HPAM在SiO_2表面的吸附量、吸附构型及两者之间形成的网状结构不同。纳米SiO_2的加入同时强化了HPAM降低油水界面张力的性能,加入质量分数为0.2%和0.5%的SiO_2后,HPAM的采收率分别提高了4.5%和6.0%。     

聚丙烯酰胺的形态结构研究

本文用电子显微镜深入的研完了部分水解聚丙烯酰胺在水溶液中的形态。给出大分子的伸展网状结构是其稀溶液高粘度的结构本质。并详细讨论了聚合物的水解度、分子量、外加盐种类及波度与分子聚集状态的关系。     

加盐浓度及水解度对PAM和HPAM的特性粘数的影响

聚丙烯酰胺(PAM)和部分水解聚丙烯酰胺(HPAM)的特性粘数[η]等物性参数与样品的水解度(DH%)、加盐浓度(C_s)密切相关。在实际应用中,无论油田水、矿山水、洗煤水,一般矿化度都较高,影响PAM和HPAM的使用性能,所以研究DH%、C_s对[η]的影响很有必要。本文在以往工作的基础上研究了[η],C_s,DH%,tgx间的关系,得出了一些有用的结果。     

部分水解聚丙烯酰胺柠檬酸铝体系临界交联浓度的研究

采用落球粘度计、核孔膜过滤、动态光散射 (DLS)和2 7Al NMR法 ,研究了高分子量、低浓度的部分水解聚丙烯酰胺 (HPAM)与柠檬酸铝 (AlCit)体系形成交联聚合物溶液 (LPS)的临界交联浓度 .研究结果表明 ,HPAM AlCit体系在聚合物浓度较低时 ,溶液中主要发生形成交联聚合物线团 (LPC)的交联反应 ,此时形成的是LPS ,聚合物浓度增加到某一临界值后 ,体系中形成线团后 ,存在线团间的交联 ,此时形成的是弱凝胶 .不同方法所测得的HPAM AlCit体系的临界交联浓度基本相同 ,对于粘均相对分子质量为 1 4× 10 7的HPAM ,在NaCl浓度为 2 0 0 0mg L ,交联比 2 0∶1时形成的交联体系 ,其临界交联浓度在 2 0 0～ 30 0mg L间 .     

Viscosity and normal stresses in branched polydisperse polymers

The steady-flow behavior of five samples of branched poly(vinyl acetate) has been studied with the Weissenberg rheogoniometer. The branching densities and molecular weight distributions were known from an analysis of the polymerization kinetics. Measurements were made on concentrated diethyl phthalate solutions (0.170 and 0.225 g/ml) at temperatures of 30 and 70°C. The viscosities of all solutions at zero shear rate were less than of solutions of linear poly(vinyl acetate) with the same weight-average molecular weight. The amount of decrease was in excellent agreement with Bueche's theory of melt viscosity in branched systems. The viscosity versus shear rate curves were surprisingly independent of molecular weight distribution, the data from all samples being superimposable on the same master curve. Relaxation times derived independently from the viscosity behavior and the normal stress data were of similar magnitude and always close to the Rouse relaxation time of each solution.     

粘度法测定部分水解聚丙烯酰胺的分子量

在 2 5℃、浓度为 1mol L的NaCl水溶液中 ,测定了聚合度 (DP)为 1 48× 10 3～ 3 79× 10 4的聚丙烯酰胺 (PAM)及其水解度 (h)在 0 %～ 70 %之间的部份水解聚丙烯酰胺 (HPAM)的特性粘度 ([η]) .根据聚电解质理论和Kowblansky的研究结果 ,建立了特性粘度 [η]与聚合度DP、水解度h之间的定量关系式 :[η]=0 1113DP0 83 2 9+0 9973DP0 753 1 (1- 0 81h1 2 )h .用该式处理方献数据 ,其平均误差为 13 74%     

聚醚酯嵌段共聚物熔体的流变性能

采用毛细管流变仪测定了组成比、聚醚分子量、熔融时间和熔融温度对嵌段聚醚酯熔体表观粘度的影响．结果发现在所研究的温度和切变速率范围内,该结构聚醚酯熔体为假塑性非牛顿流体,其粘度随聚酯段含量的增加而增加,随熔融时间增加而降低,随聚醚分子量的增大而增大．聚醚酯的零切粘度可由Ｓｐｅｎｃｅｒ Ｄｉｌｌｏｎ 公式外推得到,零切粘度对温度的依赖关系服从Ａｎｄｒａｄｅ 公式．     

交联聚合物线团的形态和尺寸研究

通过建立低压差下核孔膜过滤稀释液的方法 ,研究了低浓度HPAM与AlCit形成的交联聚合物溶液(LPS)中交联聚合物线团 (LPC)的形态和尺寸 .实验结果表明 ,LPC为球形结构 ,由于交联作用 ,其剪切变形程度有限 .低压差下核孔膜过滤法与动态光散射法 (DLS)和扫描电镜法 (SEM)相结合 ,可较为准确地判断LPC的尺寸范围 ,HPAM相对分子质量为 1 1× 10 7～ 1 4× 10 7、浓度为 0 0 2 % ,NaCl浓度 0 2 % ,交联比 2 0∶1的LPS中LPC的直径小于 1 38μm ,相当多的LPC直径在 4 5 0nm以上 ,平均流体力学直径约为 4 92nm .在一定聚合物浓度范围内 ,相同实验条件下 ,随着聚合物相对分子质量的增大 ,LPC尺寸逐渐增大 .LPS制成干片后 ,LPC的尺寸收缩有限 ,利用SEM法直接观测其形态 ,具有一定的准确性 ,可用此法对其进行研究 .     

金属阳离子对聚丙烯酰胺溶液黏度的影响及其降黏机理研究

聚丙烯酰胺(HPAM)是油田常用的驱油聚合物,用油田污水配制HPAM溶液易导致其黏度明显降低,影响驱油效果。依据埕东油田污水实测的各种金属阳离子含量来配制HPAM溶液,测得各金属阳离子对其黏度影响由大到小的顺序为:Na⁺>Fe²⁺>Ca²⁺>K⁺>Mg²⁺;通过红外光谱和扫描电镜分析金属阳离子导致HPAM溶液降黏的机理,Na⁺、K⁺、Ca²⁺、Mg²⁺主要是通过与HPAM链上的羧酸根阴离子静电引力相互作用,降低HPAM分子表面原有的电荷密度,造成分子链卷曲,同时减弱了极性基团的溶剂化能力,释放大量的"束缚水",从而使黏度显著降低;Fe²⁺离子主要是与水中溶解氧共同作用,引发自由基反应,导致HPAM骨架水解断裂,致使黏度显著降低。     

Characterization of high molecular weight polyethylenes using high temperature asymmetrical flow field-flow fractionation with on-line infrared, light scattering, and viscometry detection

High temperature asymmetrical flow field-flow fractionation (HTAF4) coupled to infrared (IR), multi-angle light scattering (MALS), and viscometry (Visc) detection is introduced as a tool for the characterization of high molecular weight polyethylenes. The high molecular weight fraction strongly affects the rheological behaviour and processability of polyethylene materials and can often not be accurately resolved by current technology such as high temperature size-exclusion chromatography (HTSEC). Molecular weight (M), radius of gyration (Rg), and intrinsic viscosity [eta] of linear high density polyethylene (HDPE) and branched low density polyethylene (LDPE) samples are studied in detail by HTAF4 and are compared to HTSEC. HTAF4 showed a better separation and mass recovery than HTSEC for very high molecular weight fractions in HDPE and LDPE samples. As no stationary phase is present in an HTAF4 channel, the technique does not show the typical drawbacks associated with HTSEC analysis of high molecular weight polyethylenes, such as, exclusion effects, shear degradation, and anomalous late elution of highly branched material. HTAF4 is applied to study the relation between the molecular weight and the zero shear viscosity eta0 for high molecular weight HDPE. It was found that the zero shear viscosity values predicted from HTAF4 results are in good qualitative agreement with measured values obtained from dynamic mechanical spectroscopy (DMS) experiments, whereas eta0 values predicted from HTSEC do not show a strong correlation. The low molecular weight cutoff of HTAF4 is approximately 5x10(4) as a result of relatively large pores in the HTAF4 channel membrane. HTAF4 is, therefore, currently not suited to analyze low molecular weight materials.     

Interaction Between the Hydrophobically Modified Polyacrylamide and HPAM-Flooding Produced Liquid

In order to utilize the produced liquid of hydrolyzed polyacrylamide (HPAM) flooding to enhance oil recovery, the interaction between hydrophobically modified polyacrylamide (HMPAM) and the produced liquid of HPAM flooding was investigated. The viscous characteristic of HMPAM in aqueous solution was investigated by Ubbelohde viscometer. The results show the intrinsic viscosity of HMPAM in aqueous solution is higher than that of HPAM, indicating that HMPAM has better effect on increasing the viscosity of aqueous solution. The viscosity of the complex system consisted of HMPAM and the produced liquid from HPAM flooding is lower than that of the HMPAM system, but higher than that of the HMPAM/HPAM complex system in mineralized water. In order to investigate the major factor of the influence on the viscosity of the HMPAM/produced liquid complex system, the viscosities of HMPAM/HPAM (and hydrolyzed HPAM with different hydrolysis degree) in distilled water and in mineralized water were studied. The fluorescence spectrum and transmission electron microscopy measurements were carried out to investigate the interaction between HPMAM and produced liquid from a microscopic perspective. These results are useful for farther enhancing oil recovery after HPAM flooding.     

Molecular simulation studies on the interaction between different polymers in aqueous solution

A molecular dynamics simulation was performed to investigate the aggregates of mixing and the interaction between different polymers in aqueous solution. These polymers include partially hydrolyzed polyacryamide (HPAM), hydroxyethylcellulose (HEC) and polyvinylpyrrolidone (PVP). The structures of mixed aggregates were analyzed from the dihedral angle distribution of: (1) pure HPAM; (2) HPAM in aqueous solution; (3) HPAM with small segments of PVP or HEC in aqueous solution. At the same time, the simulated IR spectra and the calculated interaction parameters were used to distinguish the different interactions between HPAM and PVP or HEC. In order to confirm the validity of the simulated predictions, experimental IR spectra of polymer systems were made, and the specific viscosity of the HPAM and PVP or HEC system was measured using capillary viscometry. It can be seen from the viscosity measurements that the viscosity of the HPAM/PVP system in aqueous solution decreases linearly with an increase in concentration of PVP, whereas a maximum viscosity value appears with the increase in concentration of HEC in the HPAM/HEC system. The conclusion was drawn that the interaction between HPAM and HEC is stronger than the one between HPAM and PVP, and that molecular simulation can be considered as an adjunct to experiments and can provide otherwise inaccessible (or, not easily accessible) microscopic information that experimentalists can use.