Ca10Li（PO4）7∶Dy3+,Ce3+材料的制备及发光性能

采用高温固相法制备了Ca10Li(PO4)7∶Dy3+发光材料,研究了Dy3+在Ca10Li(PO4)7基质中的发光特性。XRD测量结果表明,烧结温度为1 050℃时所制备的样品为纯相Ca10Li(PO4)7晶体。从激发谱可以看出样品主激发峰位于349 nm(6H15/2→6P7/2),363 nm(6H15/2→6P5/2),385 nm(6H15/2→6M21/2),样品可被UVLED管芯有效激发。发射谱由位于481 nm(蓝)和572 nm(黄)的两个峰组成,对应的能级跃迁为4F9/2→6H15/2、6H13/2。研究了不同Dy3+掺杂浓度对发光强度的影响,当Dy3+的摩尔分数为10%时发光最强。掺入Ce3+作为敏化剂,Ce3+→Dy3+发生共振能量传递,当掺杂量为10%Dy3+、14%Ce3+时,样品发光最强,其强度为单掺10%Dy3+时的13.4倍,发光颜色由黄白变为蓝白。     

光泽精化学发光体系的研究与应用

对光泽精化学发光体系的动力学性质、荧光光谱、化学发光光谱及化学发光机理进行研究和探讨。详细研究了光泽精 - H2 O2 - Co( )流动注射化学发光体系的最佳分析条件。结果表明 ,当光泽精 (L c)为 2 .5×10 - 5mol/L、H2 O2 为 0 .5 mol/L、Na OH为 0 .4 mol/L、CTMAB为 2 .0× 10 - 5mol/L时 ,测定 Co( )的校准曲线线性范围为 0 .0 5— 2 0 0μg/m L ,检出限为 0 .0 1μg/m L。对 10μg/m L Co( )连续测定 7次 ,相对标准偏差为 1.7%。     

DBC-偶氮胂分光光度法测定水样中钙

在 p H10 .9H3 BO3 - H3 PO4- HAc缓冲介质中 ,Ca2 +与 DBC-偶氮胂生成 1∶ 2蓝色络合物 ,最大吸收波长位于 6 2 0 nm处 ,表观摩尔吸光系数ε62 4nm=1.86× 10 4L· mol-1· cm-1,钙量在 0— 1.4μg/ m L范围内遵守比耳定律。本法用于水样中钙的测定 ,结果令人满意。     

5-(4-氯苯基偶氮)-8-苯磺酰氨基喹啉分光光度法测定微量镍(Ⅱ)

在 p H10 .5的 Na2 B4O7- Na OH介质及 CS(NH2 ) 2 、氯化十六烷基吡啶 (CPC)存在时 ,室温下镍 ( )与5 - (4 -氯苯基偶氮 ) - 8-苯磺酰氨基喹啉 (CPBSQ)反应 ,生成络合比为 1∶ 4的有色络合物 ,其最大吸收波长位于 6 0 0 nm。研究了反应的最佳条件 ,建立了一个测定 Ni( )的光度分析新方法。 Ni( )的浓度在 0—10 .0 μg/2 5 m L范围内符合比耳定律 ,其摩尔吸光系数为 1.93× 10 5L· mol-1·cm-1。考察了 2 0多种共存离子的影响 ,大多数常见离子在氨水沉淀分离后不干扰测定。方法用于合金钢中镍的测定 ,其相对标准偏差为 1.9%— 2 .1% ,标准加入回收率为 97%— 10 4 %。     

CH2Cl与OH自由基反应机理的理论研究

用量子化学从头算方法对CH2 Cl与OH自由基反应生成HCCl+H2 O、HCOCl+H2 和H2 CO +HCl的机理进行了研究 .在UMP2 (FC) / 6 311++G 水平上计算出了各物种的优化构型、振动频率 ;并在Gaussian 3(G3)水平上计算了他们的零点能 (ZPE)、相对能量及总能量 .结果表明 ,CH2 Cl和OH自由基反应首先经无垒过程生成一个富能中间体CH2 ClOH ,中间体再经过一系列原子转移、基团旋转和键断裂分别生成产物HCCl+H2 O、HCOCl+H2 和H2 CO +HCl;三者均为放热反应 ,放热量分别为 72 .81、338.5 4和 35 4 .0 8kJ/mol;生成H2 CO +HCl放出的热量比生成HCCl+H2 O放出的热量多 2 81.2 7kJ/mol,与实验结果吻合 .     

Ca(BH_4)_2络合物电子结构及热力学稳定性的第一性原理研究

利用第一性原理研究了低温及高温相Ca(BH_4)_2络合物的电子结构、晶格振动及其反应焓.计算结果表明:低温及高温相Ca(BH_4)_2中Ca~(+2)与[BH_4]~-以离子键形式相结合,[BH_4]~-离子中B原子和H原子以共价键形式相结合,对该共价键有贡献的主要是B原子的2p轨道电子,H原子的1s轨道电子.Ca(BH_4)_2可能的反应路径为:Ca(BH_4)_2→2CaH_2+CaB_6+10H_2,该反应在300 K下反应焓为43.22 kJ/molH_2.拉伸B—H键所对应的声子频率较高,其值为2360～2500 cm~(-1),这可能是导致B—H键断裂释放氢气需要较高温度的主要原因之一.     

Ca(BH4)2络合物电子结构及热力学稳定性的第一性原理研究

利用第一性原理研究了低温及高温相Ca(BH4)2络合物的电子结构、晶格振动及其反应焓。计算结果表明：低温及高温相Ca(BH4)2中Ca+2与[BH4]－以离子键形式相结合,[BH4]－离子中B原子和H原子以共价键形式相结合,对该共价键有贡献的主要是B原子的2p轨道电子,H原子的1s轨道电子。Ca(BH4)2可能的反应路径为：Ca(BH4)2→2CaH2+CaB6+10H2,该反应在300K下反应焓为43.22 kJ/mol H2。拉伸B—H键所对应的声子频率较高,其值为2360～2500cm-1,这可能是导致B—H键断裂释放氢气需要较高温度的主要原因之一。     

Ca9Al(PO4)7∶Eu2+的发光、浓度猝灭及温度稳定性

采用高温固相法制备了Ca9Al(PO4)7∶Eu2+蓝色荧光粉,研究了Ca9Al(PO4)7∶Eu2+的发光、浓度猝灭及温度稳定性.Ca9Al(PO4)7∶Eu2+的激发光谱覆盖200～350 nm紫外区;发射光谱为一主峰位于445 nm的宽谱,对应Eu2+的4f6 5d1--→4f特征跃迁.研究发现,随Eu2+掺杂量的增大,Ca9Al(PO4)7∶Eu2+的发射强度呈现先增大、后减小的变化趋势,最大发射强度对应的Eu2+掺杂量为0.01,即存在浓度猝灭效应,对应的机理为电偶极-电偶极相互作用;依据晶格常数,得出临界距离为2.297 nm.在25～300℃范围内改变光谱测量温度,发现温度升高到150℃时,Ca9Al(PO4)7∶Eu2+的发射强度变为25℃时的81.0％,对应的激活能为0.268 eV,说明材料具有较好的温度稳定性.     

2-(2''-喹啉偶氮)-5-二甲氨基苯甲酸光度法测定钢铁中的钴

合成了新试剂 2 - (2’-喹啉偶氮 ) - 5 - N,N-二甲氨基苯甲酸 (QADMAB) ,并研究了其与钴的显色反应 ,在 p H=4 .0的 KH2 PO4- K2 HPO4缓冲介质中 ,CTMAB存在下 ,QADMAB与钴反应生成 2∶ 1稳定配合物 ,λmax=6 2 0 nm,ε=1.2 5× 10 5L·mol-1· cm-1。钴含量在 0— 0 .4 mg/ L范围内符合比耳定律 ,方法用于钢铁样品中钴含量的测定 ,结果令人满意     

二正丁基锡三齿酰腙Schiff碱配合物的合成和红外光谱研究

合成了 4种三齿酰腙Schiff碱配体H2 L [H2 L1 :C6 H5C(O)NHN =CHC6 H4OH 2 ,H2 L2 :C6 H5C(O)NHN =CHC6 H3(OH) 2 2 ,4,H2 L3:NC5H4C(O)NHN =CHC6 H4OH 2 ,H2 L4:NC5H4C(O)NHN =CHC6 H3(OH) 2 2 ,4]和它们的二正丁基锡新型配合物 (n Bu) 2 SnL ,通过元素分析确定了这些配合物的组成 ,并对配合物在 4 0 0 0～ 40 0cm- 1范围内的主要红外光谱吸收峰进行了归属和讨论 ,推测出配合物可能的分子结构。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.