Influence of Pretreatment Conditions on Methane Aromatization Performance of Mo／HZSM—5 and Mo—Cu／HZSM—5 Catalysts

Mo/HZSM-5 is a good catalyst for methane aromatization, and the reaction performance of Mo/HZSM-5 and Cu modified Mo/HZSM-5 catalysts under various pretreatment conditions has been studied. The results indicate that the catalyst presented a distinguished catalytic activity, benzene selectivity and a high stability when the bed temperature was raised in N2 atmosphere.     

DEHYDROGENATION AND AROMATIZATION OF METHANE IN THE ABSENCE OF OXYGEN OVER DOPED Mo/HZSM-5 CATALYSTS

研究了在Ｍｏ／ＨＺＳＭ－５催化剂上添加助剂以及不同的反应预处理温度对甲烷无氧脱氢芳构化反应的影响。实验结果表明，由于第二组分的添加，Ｍｏ／ＨＺＳＭ－５催化剂的活性和选择性都得到了较大程度的改善。预处理温度是影响催化剂反应性能的关键因素。Ｍｏ－Ｒｕ／ＨＺＳＭ－５催化剂经过８７３Ｋ空气预处理后，甲烷在９７３Ｋ的转化率约为１０％，催化剂的稳定性也得到较大程度的提高。ＴＰＳＲ实验结果表明，Ｒｕ的加入降低了芳烃生成的温度。ＴＰＯ和ＤＴＡ实验结果表明，在Ｍｏ－Ｒｕ／ＨＺＳＭ－５催化剂上可生成较多的碳物种，结合反应结果，可以认为反应过程中生成的碳物种对甲烷的无氧脱氢芳构化反应是起积极作用的     

Methane dehydro-aromatization over Mo/HZSM-5 catalysts in the absence of oxygen: Effect of steam-treatment on catalyst stability

The effect of steam-treatment to HZSM-5 zeolite and Mo/HZSM-5 with a steaming time range of 0.5-1 h on the catalytic performance of methane dehydro-aromatization (MDA) over Mo/HZSM-5 catalyst prepared with impregnation has been studied in detail in combination with the characterization of 1H MAS NMR technique. Both the deactivation rate constant (kd) and the Brnsted acid sites per unit cell were calculated to quantitatively evaluate the stability of Mo/HZSM-5 catalysts treated with steam at 813 K before and after impregnation of molybdenum species, and the corresponding variation of their Brnsted acid sites. The results reveal that a V-shape relationship between kd and the number of B1 acid sites per unit cell is presented on Mo/HZSM-5 catalyst under the tested steam-treatment and reaction conditions.     

Propane Aromatization over Mo/HZSM-5 Catalysts

Impregnation, mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite. The structure and surface acidity of the catalysts were studied by means of XRD, FT-IR, NH3-TPD, TPR and XPS. The effects of Mo content and reaction time on stream on the aromatization of propane were investigated. It was found that the performance of the Mo/HZSM-5 catalyst prepared by the hydrothermal treatment method was much better than that of the other two catalysts. For example, under the reaction conditions of 823 K and 600 h-1, propane conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%, respectively. XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5, and larger amounts of them could penetrate into the HZSM-5 channel, as compared with the other two kinds of catalysts. These factors may be responsi     

Propane Aromatization over Mo／HZSM—5 Catalysts

Impregnation,mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite ,the structure and surface acidity of the catalysts were studied by means of XRD,FT-IR ,NH3-TPD,TPR and XPS,The effects of Mo content and reaction time on stream on the aromatization of propane were investigated,It was found that the performance of the Mo/HZSM-5 catalst prepared by the hydrothermal treatment method was much better than that of the other two catalysts,For example ,under the reaction conditions of 823 K and 600h^-1, propance conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%,respectively,XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5,and lartger amounts of them could penetrate into the HZSM-5 channel ,as compared with the other two kinds of catalysts,These factors may be responsibled for their high activities for propane aromatization,IR and NH3-TPD studies indicated that the number of Broensted acid centers decreased and the Lewis acid centers increased after Mo was introduced into the HZSM-5 zeolite.     

Ni/HZSM-5的结构及催化木糖醇水相加氢合成液体烷烃的性能研究

采用浸渍法制备了Ni/HZSM-5双功能催化剂,采用BET、XRD、NH3-TPD、H2-TPR、FTIR和TG等方法表征了催化剂比表面、孔结构、酸性、还原能力及骨架结构等信息,研究了其催化木糖醇水相加氢合成液体烷烃的性能及催化剂失活的原因。结果表明,在优化的金属中心/酸中心的协同作用下,木糖醇可通过水相加氢高选择性地合成C5-C6烷烃;过高的金属中心或酸中心均会导致C-C键断裂形成轻质烷烃,以2%Ni/HZSM-5催化剂上木糖醇水相加氢活性最高,木糖醇C转化率为94%液体烷烃总收率可达90%,这与其具有较大的比表面积、合适的孔径分布、较多的金属活性中心、适中的酸量和强酸量有关。催化剂6次重复使用后活性明显降低,其骨架部分脱铝和表面积碳是其失活的主要原因。     

在Ni/HZSM-5催化剂上低温水蒸汽重整生物油制氢

We investigated high catalytic activity of Ni/HZSM-5 catalysts synthesized by the impregna-tion method, which was successfully applied for low-temperature steam reforming of bio-oil. The influences of the catalyst composition, reforming temperature and the molar ratio of steam to carbon fed on the stream reforming process of bio-oil over the Ni/HZSM-5 catalysts were investigated in the reforming reactor. The promoting effects of current passing through the catalyst on the bio-oil reforming were also studied using the electrochemical catalytic re-forming approach. By comparing Ni/HZSM-5 with commonly used Ni/Al₂O₃ catalysts, the Ni₂₀/ZSM catalyst with Ni-loading content of about 20% on the HZSM-5 support showed the highest catalytic activity. Even at 450 oC, the hydrogen yield of about 90% with a near complete conversion of bio-oil was obtained using the Ni₂₀/ZSM catalyst. It was found that the performance of the bio-oil reforming was remarkably enhanced by the HZSM-5 supporter and the current through the catalyst. The features of the Ni/HZSM-5 catalysts were also investigated via X-ray diffraction, inductively coupled plasma and atomic emission spectroscopy, hydrogen temperature-programmed reduction, and Brunauer-Emmett-Teller methods.     

Non-oxidative conversion of methane into various petrochemical grades over tunable tri-metallic Fe-W-Mo/HZSM-5 catalyst systems

Most mono-metallic catalysts applied in non-oxidative conversion of methane exhibit low catalyst activity and limited selectivity towards useful petrochemicals. In this study, a series of thermally stable and tunable 5.4 wt% metal/support Fe-W-Mo/HZSM-5 catalyst systems were synthesized, characterized, and applied in non-oxidative conversion of methane in a custom-made stainless-steel reactor at various process conditions. Analysis of products from the reactor was done using Shimadzu 2014 gas chromatograph. Varying the amount of Fe, W, and Mo on HZSM-5 greatly influenced catalyst activity in terms of methane conversion and product distribution. When the quantities of Fe and W were increased to 2.25 wt% each and the quantity of molybdenum reduced to 0.9 wt% in the overall 5.4 wt% metal/ HZSM-5 catalyst, the resultant catalyst system became most active in methane conversion (17.4%) at 800 °C. Reducing the quantity of Fe and W each to 1.35 wt% and increasing Mo to 2.7 wt% in the overall 5.4 wt% catalyst, the resultant catalyst system became less selective towards C₂ hydrocarbons and coke, but highly selective towards xylene and benzene. Therefore, this study demonstrates that varying metal loading presents an opportunity to tune the 5.4 wt% binary Fe, W, and Mo on HZSM-5 to achieve desired methane conversion and product distribution.     

甲烷在Mo/HZSM-5催化剂上的脱氢聚合反应

对不同Mo含量的Mo／HZSM－5催化剂的结构进行了表征，并对这些催化剂的甲烷非氧气氛下的转化反应进行了考察．催化剂的BET比表面积及酸性随Mo含量的增加而降低，当Mo含量大于5％时，Mo对ZSM－5分子筛的晶型有影响，并出现MoO3物相．甲烷在700℃时可高选择性地生成苯和乙烯，最佳Mo含量大约为2％．纯的MoO3或HZSM－5上该反应几乎不进行，因此，可能是分散的钼氧离子和分子筛的酸中心是甲烷转化的活性中心，只有二者的协同作用才能促进甲烷的转化．反应后催化剂中的钼物种被还原了．催化剂上的积炭可能是催化剂失活的主要原因之一，烧炭后催化剂活性基本恢复．     

CH_4在Mo/HZSM-5及其改性催化剂上的无氧芳构化(英文)

运用微型固定床反应器装置,研究了Mo/HZSM-5催化剂的Mo载量、金属助剂改性、载体模数对甲烷无氧芳构化反应性能的影响。结果表明,Ni/Mo摩尔比为0.1的Mo-Ni/HZSM-5(SiO2/Al2O3=25)催化性能最好,其稳定性较好,芳烃收率最高可达15.74%;此时甲烷转化率60.24%,芳烃选择性26.13%。     

甲烷在Mo/HZSM-5催化剂上的脱氢聚合反应

对不同Mo含量的Mo／HZSM－5催化剂的结构进行了表征，并对这些催化剂的甲烷非氧气氛下的转化反应进行了考察．催化剂的BET比表面积及酸性随Mo含量的增加而降低，当Mo含量大于5％时，Mo对ZSM－5分子筛的晶型有影响，并出现MoO3物相．甲烷在700℃时可高选择性地生成苯和乙烯，最佳Mo含量大约为2％．纯的MoO3或HZSM－5上该反应几乎不进行，因此，可能是分散的钼氧离子和分子筛的酸中心是甲烷转化的活性中心，只有二者的协同作用才能促进甲烷的转化．反应后催化剂中的钼物种被还原了．催化剂上的积炭可能是催化剂失活的主要原因之一，烧炭后催化剂活性基本恢复．     

预处理条件对Mo／HZSM—5催化剂上丙烷芳构化的影响

采用浸渍法制备了Ｍｏ／ＨＺＳＭ－５ 分子筛催化剂,考察了Ｈ２ 、Ｎ２ 、空气预处理对催化剂丙烷芳构化活性的影响。在相同处理条件下,空气气氛更有利于提高催化剂的丙烷芳构化活性。在空气焙烧过程中,氧化钼物种向分子筛内表面分散。在Ｈ２ 还原处理过程中,表面钼物种部分被还原为Ｍｏ４ ＋ 。随还原时间延长,催化剂芳构化活性升高,同时发生少量Ｍｏ 物种向分子筛孔道内迁移     

Mo/HZSM-5丙烷芳构化催化性能及其吸附量热的研究

采用等量浸渍法制得一系列不同担载量的Ｍｏ／ＨＺＳＭ－５催化剂,运用ＸＲＤ和ＦＴＩＲ方法考察了Ｍｏ物种在催化剂表面的分散状态,首次采用微分吸一热技术对Ｍｏ／ＨｚＳＭ－５催化剂的表面酸性进行表征。同时研究了催化剂对丙烷芳构化的反应活性。结果表明：对于担载Ｍｏ的ＨＺＳＭ－５分子筛催化剂,Ｍｏ物种在ＨＺＳＭ－５分子筛表面上顺序为ＨＺＳＭ－５〉１％Ｍｏ／ＨＺＳＭ－５〉２％Ｍｏ／ＨＺＳＭ－５分子筛本身表面的酸     

ACo_2O_4/HZSM-5催化剂上N_2O的直接分解

分别采用柠檬酸络合燃烧法和低温络合浸渍法制备尖晶石型复合金属氧化物催化剂ACo2O4(A=Mg,Ni,Zn)和分子筛负载尖晶石型复合金属氧化物催化剂ACo2O4/HZSM-5(A=Mg,Fe,Ni,Cu,Zn,Zr,La).采用X射线衍射(XRD)、氨程序升温脱附(NH3-TPD)、扫描电子显微镜(SEM)和X射线能谱(EDS)等手段对催化剂进行表征,并在固定床微型反应器中评价其催化分解N2O活性.实验结果表明,A位离子种类影响ACo2O4/HZSM-5催化剂活性,以Ni、Fe、Zr或La为A位离子时,催化剂的活性较好,N2O分解温度低.ACo2O4/HZSM-5催化剂的活性高于ACo2O4尖晶石型复合氧化物,一方面是ACo2O4在分子筛HZSM-5载体上高度分散,使其以超细颗粒形态存在,另一方面ACo2O4/HZSM-5催化剂具有适宜的酸性,可提高催化剂的活性.     

钾改性对Au/ZSM-5催化剂上正丁烷裂解性能的影响

采用负压沉积沉淀法制备了负载型Au/HZSM-5催化剂,采用X射线衍射（XRD）、透射电镜（TEM）、Ｘ射线光电子能谱（XPS）、NH3-TPD、紫外可见漫反射（UV-vis）等技术对催化剂进行了表征分析,并考察了催化剂对正丁烷裂解性能的影响。结果表明,Au金属成功负载到HZSM-5催化剂上,并且金颗粒的尺寸受负载量的影响,其中1.0%Au/HZSM-5催化剂中的金颗粒粒径最小,约为5～10nm。钾离子作为一种碱性离子可以调节载体酸性,随着K离子的引入xK-Au/HZSM-5催化剂的酸性逐渐降低,使Au0的电子结合能更高。相对于HZSM-5,2.0Au/HZSM-5催化剂对于正丁烷的转化率从13.1%提升到了37.5%,对丙烯的选择性从17.2%提升到了52.5%。随着K离子的引入,催化剂对于丁烯以及异丁烷的选择性有所提高,当K离子负荷为0.08%时,对丁烯的选择性从3.8%提高到36.9%,负荷为0.1%时,对异丁烷的选择性由2.8%提升到51.8%。但原料转化率低于2.0Au/HZSM-5,这可能与K的加入降低催化剂酸改性有关。此外通过研究Au/HZSM-5用K+修饰得知Au+离子是Au/HZSM-5催化剂转化正丁烷主要活性中心。     

Effect of Fe-Mo promoters on HZSM-5 zeolite catalyst for 1-hexene aromatization

The promotional effect of Fe-Mo species introduced into HZSM-5 (Zeolyst Int., SiO₂/Al₂O₃ ≈ 30) zeolite catalyst by the wetness impregnation method for the 1-hexene aromatization was investigated. The structure and catalytic performance for the aromatization of 1-hexene over xFeyMo-ZSM-5 catalysts in comparison with unmodified HZSM-5 catalysts were studied. The xFeyMo-ZSM-5 catalysts contain fixed loading (5 wt%) and variable Fe/Mo ratio. The catalysts were characterized by BET, ICP-AES, HRSEM-EDS, HRTEM, XRD, FTIR, H₂-TPR, NH₃-TPD, and pyridine DRIFT spectroscopy. The characterization data confirmed the existence of Fe and Mo species in the zeolite matrix. With Fe and Mo species implementation to HZSM-5 zeolite, the amount of the acid sites decreased, but the selectivities to C₉₊ aromatics increased. The catalyst evaluation was performed at 350 °C for 6 h on-stream at atmospheric pressure using a fixed-bed quartz tube reactor. The selectivity to products of different carbon number was affected by the Fe/Mo ratio within the zeolite. It was found the product distribution of grouped fractions of C₁–C₁₇₊ from the liquid product. The results indicate that the optimum ratio of Fe/Mo is 1–1.5. The highest selectivity for gasoline and distillate ranges was obtained for the 2.5wt%Fe2.5wt%Mo- and 3wt%Fe2wt%Mo-ZSM-5 samples, which was higher than that for parent HZSM-5 catalyst.     

添加Mo对Cu/HZSM-5催化剂性能影响

负载催化剂;二氧化碳加氢;二氧化碳;添加Mo对Cu/HZSM-5催化剂性能影响     

Enhanced Stability of Mo-Promoted Zn/HZSM-5 Catalyst for Methanol to Aromatics

A Mo-promoted Zn/HZSM-5 catalyst was prepared by isometric impregnation method (IM). The physicochemical properties of catalysts were characterized by X-ray diffraction, registration of N₂ adsorption-desorption isotherms, transmission electron microscopy, NH₃ temperature-programmed desorption and IR spectroscopic study of pyridine adsorption. The results show that by doping zeolite with Mo species it is possible to tune the microstructures, acidity and crystallinity of the catalyst. Additionally, it was found that the 1%Mo(IM)–5%Zn(IE)/HZSM-5 catalyst had a high catalytic activity and stability for methanol to aromatics (MTA) reaction. The yield of aromatics reached 77.3% at 450°C and TOS = 3 h. When the TOS = 98 h, the yield of total aromatics remains at a 60.4% level. The lifetime of catalysts was influenced by the synergetic effect of Brønsted and Lewis acid sites, so the modification with Mo may bring an opportunity to prolong the lifetime of Zn/HZSM-5 catalyst in the MTA reaction. The metal components are sintered and lost in continuous reaction-regeneration cycles. Accordingly, the activity of deactivated catalyst cannot be completely restored to the initial level.     

Non-Oxidative Aromatization of CH4-C3H8 La-Promoted Zn/HZSM-5 Catalysts

The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h^-1 and CH4/C3H8 （mol ratio）=5：l. The propane conversion and the aromatic selectivities were up to 99% and 60% over the catalyst respectively, while methane conversion had an induction period with the highest conversion of 30%. The structure and surface acidity of the catalysts were characterized by XRD, NH3-TPD and TG-DTA. The influences of reaction and regenerative conditions on the activity and selectivity were also investigated.     

甲烷脱氢芳构化Mo/HZSM-5基催化剂表征

利用H2-TPR、XPS、EPR等谱学方法，对Mo／HZSM－5基催化剂的可还原性以及工作态催化剂上钼物种的价态进行了表征研究．结果表明，随着焙烧温度的升高，前驱态催化剂中可还原钢物种在总钼量中所占比率明显下降；工作态催化剂表面存在混合价态的Mo物种：以Mo4 为主，Mo5 为次；673K焙烧制备并经DHAM反应操作的催化剂上检测到Mo5 的EPR讯号相当弱，而973K焙烧制备并经同样反应操作的催化剂，其Mo5 EPR讯号却强得多；酸促进的Mo／HZSM－5基催化剂上高的甲烷转化活性与工作态催化剂表面Mo5 物种的浓度并不存在顺变关系，而与表面酸位（尤其是B酸位）及Mo4 物种的浓度密切相关．