Spectrophotometric and atomic absorption determination of ramipril, enalapril maleate and fosinopril through ternary complex formation with molybdenum (V)-thiocyanate (Mo(V)-SCN)

Three different sensitive and accurate spectroscopic procedures were developed for the determination of three angiotensin-converting enzyme inhibitors, namely, ramipril, enalapril maleate and fosinopril. The first two spectrophotometric (extractive and non-extractive) procedures were based on ternary complex formation with molybdenum(V) thiocyanate. The formed complex can be determined by extraction with chloroform measured at lambdamax 517 nm Beer's law was obeyed in the concentration range from (10--90 microg ml(-1)) for ramipril and fosinopril and (4--36 microg ml(-1)) for enalapril maleate with molar absorptivity 1.2x10(4), 2x10(4) and 3.4x10(4) l mol(-1) cm(-1), respectively, or by direct measurement after addition of benzalkonium chloride as surfactant and measuring the formed ternary complex at lambdamax 545 nm with a linear relationship in the concentration range from (8-7-2 microg ml(-1)), (3--27 microg ml(-1)) and (8--72 microg ml(-1)) for ramipril, enalapril maleate and fosinopril with molar absorptivity 1.5x10(4), 5x10(4) and 2.1x10(4) l mol(-1) cm(-1), respectively. The third procedure is atomic absorption measurement through the quantitative determination of molybdenum content of the complex. These methods hold their accuracy and precision well when applied to the determination of ramipril, enalapril maleate and fosinopril in their dosage forms.     

Spectrophotometric determination of urea in dermatologic formulations and cosmetics

A rapid, relatively sensitive, and low-cost method for the determination of water-soluble urea content in dermatological therapy products and cosmetics is proposed using a new spectrophotometric assay with water as the only extraction solvent. Spectrophotometric methods involve addition of a known excess of bromate to urea in an acid medium, followed by the determination of residual bromine and chlorine reacting with methyl orange and measurement of absorbance at 505 nm. The absorbance increases linearly with urea concentration (r = 0.9998). The systems obey Beer's law for 6 - 90 microg ml(-1). The calculated apparent molar absorbance values are found to be 4.537 x 10(3) dm(3) mol(-1) cm(-1) and the Sandell's sensitivity is 0.013 microg cm(-2). The variables affecting the rate of the reaction were investigated. The relative standard deviation for five-replication determination of 60 microg ml(-1) urea was 2.1% and the detection limit of the method is 0.34 ng ml(-1).     

Simultaneous determination of manganese and zinc in mixtures using first- and second-derivative spectrophotometry

A new direct spectrophotometric determination of manganese with 5,8-dihydroxy-1,4-naphthoquinone (naphthazarin,NAZA) is reported. Absorption maximum, molar absorptivity and Sandell's sensitivity of 1:2 (M:L) complex are 695 nm, 1.88x10(4) l mol(-1) cm(-1) and 2.92 ng cm(-2), respectively. A linear calibration graph is obtained up to a concentration of 7.2 mug ml(-1) of manganese. The optimum range for determination (Ringbom) is between 0.20 and 6.8 mug ml(-1). A rapid method for simultaneous determination of manganese and zinc in their mixture using derivative spectra is described. The range 0.28-5.6 mug ml(-1) manganese could be determined in the presence of 0.33-6.8 mug ml(-1) zinc and vice versa. The developed method was applied to the simultaneous spectrophotometric determination of manganese and zinc in some synthetic mixtures and was found to give satisfactory results.     

Interaction of nickel with 4-(2'-benzothiazolylazo) salicylic acid (BTAS) and simultaneous first-derivative spectrophotometric determination of nickel(II) and iron(III)

The solution properties of nickel complex with 4-(2'-benzo-thiazolylazo) salicylic acid (BTAS) have been studied by zero-order absorption spectrophotometry in 40% (v/v) ethanol at 20 degrees C and an ionic strength of 0.1 mol dm(-3) (KNO(3)). The equilibria that exist in solution were established and the basic characteristics of complexes formed were determined. A new direct spectrophotometric method for the determination of trace amounts of the nickel is proposed based on the formation of the Ni (BTAS) complex at pH 7.0. The absorption maximum, molar absorbtivity, and Sandell's sensitivity of 1:1 (M:L) complex are 525 nm, 0.6 x 10(4) l mol(-1) cm(-1) and 2.824 x 10(-9) microg cm(-2), respectively. The use of first-derivative spectrophotometry eliminates the interference of iron and enables the simultaneous determination of nickel and iron using BTAS. Quantitative determination of Ni(II) and Fe(III) is possible in the range (0.59-7.08) and (2.1-8.4) microg ml(-1), respectively with a relative standard deviation of 0.5%. The proposed method has been successfully applied to the simultaneous spectrophotometric determination of nickel and iron in steel alloys and aluminum alloys.     

H-point standard addition method for simultaneous spectrophotometric determination of Co(II) and Ni(II) by 1-(2-pyridylazo)2-naphthol in micellar media

A very simple and selective spectrophotometric method for simultaneous determination of Co(II) and Ni(II) by 1-(2-pyridylazo) 2-naphthol (PAN), in micellar media, using H-point standard addition method (HPSAM) is described. The ligand and its metal complexes (Co(II)-PAN and Ni(II)-PAN) were made water-soluble by the neutral surfactant Triton X-100, and therefore, no extraction with organic solvents was required. Formation of both the complexes was complete within 10 min at pH 9 (adjusted by ammonia buffer). The linear range was 0.10-2.00 microg ml(-1) for Co(II) and 0.05-1.50 microg ml(-1) for Ni(II). The relative standard deviation (R.S.D.) for the simultaneous determination of 0.50 microg ml(-1) each of Co(II) and Ni(II) was 2.32 and 3.13%, respectively. Interference effects of common anions and cations were studied and the method was applied to simultaneous determination of Co(II) and Ni(II) in alloy samples. The method was compared with derivative spectrophotometric method.     

Stability indicating methods for determination of Donepezil Hydrochloride according to ICH guidelines

Stability indicating assays for determination of Donepezil Hydrochloride in presence of its oxidative degradate were developed and validated. The first three are spectrophotometric methods depending on using zero order (D(0)), first order (D(1)) and second order (D(2)) spectra. The absorbance was measured at 315 nm for (D(0)) while the amplitude was measured at 332.1nm for (D(1)) and 340 nm for (D(2)) using deionized water as a solvent. Donepezil Hydrochloride (I) can be determined in the presence of up to 70% of its oxidative degradate (II) using (D(0)), 80% using (D(1)) and 90% using (D(2)). The linearity range was found to be 8-56 microg ml(-1) for (D(0)), (D(1)) and (D(2)). These methods were applied for the analysis of I in both powder and tablet form. Also, a spectrofluorimetric method depending on measuring the native fluorescence of I in deionized water using lambda excitation 226 nm and lambda emission 391 nm is suggested. The linearity range was found to be 0.32-3.20 microg ml(-1) using this method, I was determined in the presence of up to 90% of II. The proposed method was applied for the analysis of I in tablet form as well as in human plasma. The last method depends on using TLC separation of I from its oxidative degradate II and I was then determined spectrodensitometrically. The mobile phase was methanol : chloroform : 25% ammonia (16 : 64 : 0.1 by volume). The linearity range was found to be 2-15 microg/spot. This method was applied to the analysis of I in both powder and tablet form using acetonitrile as a solvent.     

A simple spectrophotometric method for the determination of copper in industrial, environmental, biological and soil samples using 2,5-dimercapto-1,3,4-thiadiazole.

A simple spectrophotometric method is presented for the rapid determination of copper at a trace level using 2,5-dimercapto-1,3,4-thiadiazole (DMTD) as a new spectrophotometric reagent. The method is based on the reaction of non-absorbent DMTD in a slightly acidic (0.002-0.014 mol dm(-3) sulfuric acid) aqueous solution with copper(II) to produce a highly absorbent greenish-yellow chelate product that has an absorption maximum at 390 nm. The reaction is instantaneous and the absorbance remains stable for 24 h. The average molar absorption coefficient and Sandell's sensitivity were found to be 5.65 x 10(4) dm3 mol(-1) cm(-1) and 10 ng cm(-2) of CuII, respectively. Linear calibration graphs were obtained for 0.1-20 microg cm(-3) of CuII; the stoichiometric composition of the chelate is 1:2 (Cu:DMTD). A large excess of over 50 cations, anions and complexing agents (e.g. tartrate, oxalate, citrate, phosphate, thiourea, SCN-) do not interfere in the determination. The method was successfully used for the determination of copper in several Standard Reference Materials as well as in some environmental water samples, biological samples, soil samples and solutions containing both copper(I) and copper(II) and complex synthetic mixtures. The method has high precision and accuracy (s = +/-0.01 for 0.5 microg cm(-1)).     

Spectrophotometric and second-derivative spectrophotometric determination of mercury in organomercurials by means of benzyl 2-pyridyl ketone 2-quinolylhydrazone

Mercury(II) reacts with benzyl 2-pyridylketone 2-quinolylhydrazone (BPKQH) in the pH range 9.0-10.4, to form a stable 1:2 (metal:ligand) complex which has a sharp absorption maximum at 475 nm and molar absorptivity 5.01 x 10(4) 1.mole(-1).cm(-1). It is proposed for use in spectrophotometric determination of mercury at microg/ml levels and analysis for organomercurials. The sensitivity of the method can be increased significantly by employing derivative spectrophotometry, making mercury determination at ng ml levels feasible.     

Simultaneous determination of gallium and indium with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in cationic micellar medium using derivative spectrophotometry.

A new derivative spectrophotometric method for rapid and selective trace analysis of Ga3+ and In3+ and for their simultaneous determination using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in a cationic micellar medium is reported. Molar absorptivity and Sandell's sensitivity of 1:1 Ga+ and In3+ complexes at their lambda(max) 553 nm and 558 nm are: 7.22 x 10(4) l mol(-1) cm(-1) and 5.85 x 10(4) l mol(-1) cm(-1), and 0.96 ng cm(-2) and 1.96 ng cm(-2), respectively. Linearity is observed in the concentration range 0.023-0.700 microg ml(-1) for gallium and 0.076-1.52 microg ml(-1) for indium; IUPAC detection limit is 0.012 and 0.035 ng ml(-1), respectively. These metal ions interfere with the determination of each other. However, 0.07-0.70 microg ml(-1) Ga3+ and 0.115-1.150 microg ml(-1) In3+ could be determined simultaneously when present together by the derivative method without any prior separation. The proposed procedures have been successfully applied for the individual and simultaneous determination of gallium and indium in synthetic binary mixtures, standard reference materials and environmental samples.     

Extractive spectrophotometric determination of Cobalt(II) in synthetic and pharmaceutical samples using Cyanex 923.

Cyanex 923 has been proposed as a sensitive analytical reagent for the direct extractive spectrophotometric determination of cobalt(II). Cobalt(II) forms a blue-colored complex with Cyanex 923 in the organic phase. The maximum absorbance of the complex is measured at 635 nm. Beer's law was obeyed in the range 58.9 - 589.0 microg of cobalt. The molar absorptivitiy and Sandell's sensitivity of the complex was calculated to be 6.79 x 10920 l mol(-1) cm(-1) and 0.088 microg cm(-2), respectively. The nature of the extracted species was found to be Co(SCN)2 x 2S. An excellent linearity with a correlation coefficient value of 0.999 was obtained for the Co(II)-Cyanex 923 complex. Stability and regeneration of the reagent (Cyanex 923) for reuse is the main advantage of the present method. The method was successfully applied to the determination of cobalt in synthetic mixtures and pharmaceutical samples was found to give values close to the actual ones. Standard alloy samples, such as high-speed tool BCS 484 and 485, have been tested for the determination of cobalt for the purpose of validating the present method. The results of the proposed method are comparable with atomic absorption spectrometry and were found to be in good agreement.     

Spectrophotometric determination of aluminium by morin

A direct spectrophotometric method for the determination of aluminium with morin has been developed. Morin reacts in slightly acidic 50% ethanolic media (0.0001-0.0015 M H(2)SO(4)) with Al to give a deep-yellow chelate which has an absorption maximum at 421 nm. The average molar absorptivity and Sandell's sensitivity were found to be 5.3 x 10(3) l mol(-1) cm(-1) and 5 ng of Al cm(-2), respectively. The reaction is instantaneous and absorbance remains stable for 48 h. The colour system obeys Beer's law from 10 ng ml(-1) to 5.0 mug ml(-1) of Al; the stoichiometric composition of the chelate is 2:3 (Al:morin). The interference from over 50 cations, anions and complexing agents has been studied at 0.1 mug ml(-1) of Al. The method was applied successfully to some certified reference material samples (alloys and steels), environmental waters (inland and surface), biological samples (human blood, urine and gallstone), soils and complex synthetic mixtures.     

Spectrophotometric determination of aluminum with m-carboxyphenylfluorone, a novel chemical probe, and its application.

A highly spectrophotometric method for the determination of aluminum was developed. This method used the color reaction between m-carboxyphenylfluorone (MCPF) as a novel chemical probe and aluminum in the presence of a surfactant, poly(N-vinylpyrrolidone) (PVP, K-90) (0.03 - 1.40 microg of aluminum in a final volume of 10 ml at 561 nm). The proposed method showed excellent sensitivity (molar absorptibity of 1.70 x 10(5) l mol(-1) cm(-1)) and reproducibility (within-day precision: RSD = 0.35% n = 6, between-day precision: RSD = 0.44% n = 6). Linearity was achieved over the range 3 - 140 microg L(-1) with a correlation coefficient of 0.9999, and the effects of foreign substances were low.     

4-(N,N-diethylamino) benzaldehyde thiosemicarbazone in the spectrophotometric determination of palladium

4-(N,N-diethylamino)benzaldehyde thiosemicarbazone(DEABT) is proposed as a sensitive and selective analytical reagent for the spectrophotometric determination of palladium(II). The reagent reacts with palladium (II) in a potassium hydrogen phthalate-hydrochloric acid buffer of pH 3.0, to form a yellow complex. Beer's law is obeyed in the concentration range up to 3.60 microgmL(-1). The optimum concentration range for minimum photometric error as determined by Ringbom plot method is 0.36 - 3.24 microg mL(-1). The yellow Pd(II)-DEABT complex shows a maximum absorbance at 408 nm, with molar absorptivity of 3.33 x 10(4) dm3 mol(-1) cm(-1) and Sandell's sensitivity of the complex from Beer's data, for D = 0.001, is 0.0032 microg cm(-2). The composition of the Pd(II)-DEABT complex is found to be 1:2 (M:L). The interference of various cations and anions in the method were studied. The proposed method was successfully used for the determination of Pd(II) in alloys, catalysts, complexes and model mixtures with a fair degree of accuracy.     

Spectrophotometric determination of uric acid based on fading of o-hydroxyhydroquinonephthalein-palladium(II)-hexadecyltrimethyl-ammonium complex.

A simple and highly sensitive spectrophotometric method for the determination of uric acid (UA) was established based on fading of the o-hydroxyhydroquinonephthalein-palladium(II)-hexadecyltrimethylammonium complex. In the determination of UA, Beer's law is obeyed in the range of 0.01-0.20 microg ml(-1), with an effective molar absorptivity at 635 nm, the relative standard deviation being 6.5 x 10(5) dm(3) mol(-1) cm(-1) and 1.5% (n = 5). This method is about 20-times more sensitive than the conventional methods. The method was successfully applied to the assay of UA in human urine.     

Spectrophotometric determination of some drugs for osteoporosis

Three simple, accurate and sensitive spectrophotometric methods are developed for the determination of some new drugs for the treatment of osteoporosis: risedronate sodium (I), alendronate sodium (II) and etidronate disodium (III). The first method is based on the measurement of difference in absorbance (Delta A) of risedronate sodium in 0.01 mol l(-1) hydrochloric and 0.1 mol l(-1) sodium hydroxide at 262 nm. Beer's law is obeyed over a concentration range of 15-150 microg ml(-1) with mean recovery 99.75+/-1.22 and molar absorptivity (epsilon) 1.891 x 10(3). The second method is based on the reaction of the primary amino group of (II) with ninhydrin reagent in methanolic medium in the presence of 0.05 mol l(-1) sodium bicarbonate. The colored product is measured at 568 nm, and the linearity range is found to be 3.75-45 microg ml(-1) with mean recovery 99.77+/-0.73 and epsilon 9.425 x 10(3). The third method is based on oxidation of the three mentioned drugs with ceric (IV) sulphate in 0.5 mol l(-1) sulphuric acid at room temperature and subsequent measurement of the excess unreacted cerium (IV) sulphate at 320 nm. The method obeyed Beer's law over a concentration range of 2-24 microg ml(-1) for the three drugs with mean recovery 99.79+/-1.16, 99.73+/-1.38 and 99.86+/-1.13 and epsilon 14.427 x 10(3), 13.813 x 10(3) and 14.000 x 10(3) for drugs I, II, III respectively. The proposed methods were successfully applied for the determination of the studied drugs in bulk powder and in pharmaceutical formulations. The results were found to agree statistically with those obtained the reported methods. Furthermore, the methods were validated according to USP regulations and also assessed by applying the standard addition technique.     

Spectrophotometric determination of glucosamine and its analogous amino sugars with o-hydroxyhydroquinonephthalein and palladium(II).

A simple and highly sensitive spectrophotometric method for the determination of glucosamine and its analogous amino sugars was established based on fading of the palladium(II)-o-hydroxyhydroquinonephthalein-hexadecyltrimethylammonium complex. In the determination of glucosamine, Beer's law is obeyed in the range of 0.02 - 0.18 microg ml(-1), with an effective molar absorptivity at 630 nm and the relative standard deviation being 8.4 x 10(5) dm3 mol(-1) cm(-1) and 1.08% (n = 10). This method is about 70-times more sensitive than the Elson-Morgan method. The method was successfully applied to the assay of glucosamine in actual samples.     

Spectrophotometric determination of platinum in glass after extraction with polyurethane foam

A spectrophotometric method has been developed for determination of trace amounts of platinum in glass. The method is based on the extraction of platinum(II) from 1M hydrochloric acid containing 0.2M stannous chloride and 4 x 10(-4)M dithizone onto polyurethane foam, elution with acetone (containing 3% v/v concentrated hydrochloric acid) and measurement of the absorbance of the eluate at 530 nm. Beer's law is obeyed up to 10.0 microg/ml Pt. The minimum platinum level in the eluate that can be determined by this method is 0.1 microg/ml.     

Spectrophotometric determination of nickel with p-acetylarsenazo

A spectrophotometric method for the determination of trace amounts of nickel is described. At pH 6, nickel reacts with p-acetylarsenazo to form a 1:2 coloured complex with an absorption maximum at 630 nm. The apparent molar absorptivity is 6.5 x 10(4) l.mol(-1) . cm(-1) . Beer's law is obeyed over the concentration range of 0-0.8 microg/ml. The proposed method is selective, sensitive and can be applied to the determination of nickel in aluminum alloy.     

Study of the titanium-phenylfluorone complex formed in the presence of Triton X-305 and emulsifier OP

A highly sensitive method for the spectrophotometric determination of titanium with phenylfluorone (PF) in the presence of Triton X-305 and emulsifier OP has been developed. In acid medium (pH 1.4-2.2) Ti(IV) forms red-violet complexes with PF, Triton X-305 and OP. The complex exhibits maximum absorption at 540 nm. The molar absorptivity is 1.63 x 10(5) 1.mole(-1).cm(-1). The Ti:PF ratio in the complex is 1:2. Beer's law is obeyed in the titanium concentration range 0-0.2 microg/ml in the final solution. Fluoride and EDTA interfere. The method has been used for the rapid direct determination of microamounts of Ti(IV) in soils and cereals with satisfactory results.