A facile, microwave-assisted synthesis of novel optically active polyamides derived from 5-(3-methyl-2-phthalimidylpentanoylamino)isophthalic acid and different diisocyanates

5-(3-Methyl-2-phthalimidylpentanoylamino)isophthalic acid as a novel aromatic diacid monomer was prepared in three steps. In the first step, phthalic anhydride was reacted with l-isoleucine in acetic acid solution, and the resulting imide acid was obtained in high yield. In the second step, treatment of this imide acid with excess thionyl chloride gave aliphatic acid chloride in good yield. In the last step, this acid chloride was reacted with 5-aminoisophthalic acid to provide novel bulky chiral aromatic diacid monomer. The direct polycondensation reactions of this diacid with several aromatic and aliphatic diisocyanates such as 4,4′-methylenebis(phenyl isocyanate), toluylene-2,4-diisocyanate, isophorone diisocyanate and hexamethylene diisocyanate were carried out under microwave irradiation. In order to compare this method with classical heating, the polymerization reactions were also performed under solution polycondensation conditions. The polymerization reactions occurred rapidly under microwave conditions and produced a series of novel optically active polyamides (PA)s containing pendent phthalimide group, with good yields and moderate inherent viscosities of 0.17-0.60 dL/g. Some of the new PAs showed good solubility and are readily soluble in organic solvents. The resulting macromolecules were characterized by FT-IR, specific rotation, and representative ones by ¹H NMR, elemental and thermogravimetric analyses (TGA).     

Rapid synthesis of optically active poly(amide-imide)s by direct polycondensation of aromatic dicarboxylic acid with aromatic diamines

4,4^′-(Hexafluoroisopropylidene)-N,N^′-bis(phthaloyl-l-leucine-p-amidobenzoic acid) (2) was prepared from the reaction of 4,4^′-(hexafluoroisopropylidene)-N,N^′-bis(phthaloyl-l-leucine) diacid chloride with p-aminobenzoic acid. The direct polycondensation reaction of monomer (2) with p-phenylenediamine (2a), 4,4^′-diaminodiphenylsulfone (2b), 2,4-diaminotoluene (2c), 2,6-diaminopyridine (2d), m-phenylene diamine (2e), benzidine (2f), 4,4^′-diaminodiphenylether (2g) and 4,4^′-diaminodiphenyl methane (2h) was carried out in a medium consisting of triphenyl phosphite, N-methyl-2-pyrolidone, pyridine, and calcium chloride. The homogeneous mixture was heated at 220 °C for 1 min under nitrogen. The resulting poly(amide-imide)s (PAIs) having inherent viscosities 0.27-0.78 dl/g were obtained in high yield and are optically active and thermally stable. All of the above polymers were fully characterized by IR spectroscopy, elemental analyses and specific rotation. Some structural characterization and physical properties of this new optically active PAIs are reported.     

Synthesis and characterization of novel optically active poly(amide-imide)s via direct amidation

N,N′-Pyromelliticdiimido-di-l-methionine (3) was prepared from the reaction of pyromellitic dianhydride (1) with l-methionine (2) in glacial acetic acid and pyridine solution at refluxing temperature. The direct polycondensation reaction of the monomer diimide-diacid (3) with 1,3-phenylenediamine (4a), 1,4-phenylenediamine (4b), 2,6-diaminopyridine (4c), 3,5-diaminopyridine (4d), 4,4′-diaminodiphenylether (4e) and 4,4′-diaminodiphenylsulfone (4f) was carried out in a medium consisting of triphenyl phosphate, N-methyl-2-pyrolidone, pyridine and calcium chloride. The resulting poly(amide-imide)s having inherent viscosities 0.45-0.53 dl g⁻¹ were obtained in high yields and are optically active and thermally stable. All of the above compounds were fully characterized by IR spectroscopy, elemental analyses and specific rotation. Some structural characterization and physical properties of these new optically active poly(amide-imide)s are reported.     

Synthesis and characterization of novel aromatic polyamides derived from two heterocyclic diamines

Two diamines were synthesized as new aromatic monomers. A series of novel aromatic polyamides (aramids) were also synthesized by direct and indirect polycondensation of these diamines with various aromatic dicarboxylic acids. These aramids have inherent viscosities of 0.43-0.84 dl/g and were obtained in quantitative yield.     

Synthesis and characterization of optically active poly(amide-imide)s containing photosensitive chalcone units in the main chain

<正>A series of new optically active poly(amide-imide)s were synthesized by direct polycondensation reaction of 4,4'-diaminochalcone with several N-trimellitylimido-L-amino acids using a tosyl chloride(TsCl),pyridine(Py) and dimethylformamide(DMF) system as condensing agent.The resulting thermally stable poly(amide-imide)s were obtained in good to high yields and inherent viscosities ranging between 0.35 dL/g and 0.58 dL/g and were characterized with FTIR, ~1H-NMR,CHN,Ultraviolet,TGA and DTG techniques.     

Thermally stable and organo-soluble polyamides containing triazine rings and ether linkages in the main chain: Synthesis and characterization

In order to synthesize new polyamide(PA) 5 and copolyamides(Co PA) 7a-7d, a new-type of dicarboxylic acid containing triazine ring was successfully synthesized from 2,4-dichloro-6-methoxy-s-triazine 1 and 4-aminobenzoic acid. New polyamide 5 containing triazine moiety was prepared from 4,4'-(6-methoxy-1,3,5-triazine-2,4-diyl)bis(azanediyl)dibenzoic acid 3 and 4,4′-diaminodiphenylether by direct polycondensation reaction. Then new series thermally stable copolyamides 7a-7d with high solubility in common organic solvents were synthesized from the direct polycondensation reaction of diacid 3 as a first monomer, aliphatic-aromatic diacids 6a-6d as second diacids and 4,4′-diaminodiphenylether. All of the above polymers were fully characterized by 1H-NMR and FTIR spectroscopy, elemental analysis(CHN), inherent viscosity, solubility tests, gel permeation chromatography(GPC), differential scanning calorimetry(DSC) and thermogravimetric analysis(TGA). The resulted Co PAs 7a-7d have shown good inherent viscosities, solubility and thermal properties.     

Synthesis of aromatic poly(amide-imide)s from novel diimide-diacid (DIDA) containing sulphone and bulky pendant groups by direct polycondensation with various diamines

A novel diimide-diacid (DIDA) monomer, 4-{4-[(4-methyl phenyl) sulphonyl]}-1,3-bis-trimellitoimido benzene containing sulphone and bulky pendant groups was successfully synthesized and used to synthesize a series of wholly aromatic poly(amide-imide)s (PAIs) by direct polycondensation method. The direct polycondensation of newly synthesized DIDA with different diamines was carried out via Yamazaki’s phosphorylation method using triphenyl phosphite and pyridine system. The resulting poly(amide-imide)s were obtained in quantitative yields with inherent viscosities 0.36-0.47 dl/g in DMAc at 30 ± 0.1 °C. The poly(amide-imide)s were amorphous and were readily soluble in various solvents such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethylsulfoxide (DMSO), and pyridine. Tough and flexible films were obtained by casting their DMAc solution. According to thermogravimetric analysis, the polymers were fairly stable up to temperature around 396 °C, and 10% weight losses in the temperature range of 476-511 °C that showed good thermal stabilities of these polymers.     

Synthesis and characterization of new optically active copoly(amid-imide)s based on N-phthalimido-L-aspartic acid and aromatic diamines

<正>In this article,six new optically active copoly(amide-imide)s(10a-f) were synthesized through the direct polycondensation reaction of N-phthalimido-L-aspartic acid(4) with 1,5-diamino naphthalene(8),3,4-diamino benzophenone(9) in the presence of therphthahc acid(7),fumaric acid(6) and adipic acid(5) as a second diacid in a medium consisting of N-methyl-2-pyrrolidone,triphenyl phosphite, calcium chloride and pyridine.The resulting copolymers were fully characterized by means of FT-IR spectroscopy,elemental analyses, inherent viscosity,solubility tests and UV-vis spectroscopy.Thermal properties of resulting copolymers(10a-c) containing three different second diacid in the main chain were compared by using TGA and DTG thermograms.     

Synthesis and properties of thermally stable and optically active novel wholly aromatic polyesters containing a chiral pendent group

5-(2-Phthalimidyl-3-methyl butanoylamino)isophthalic acid (5), as a novel diacid monomer containing phthalimide and flexible chiral groups, was prepared by the reaction of 2-phthalimidyl-3-methyl butyric acid chloride (4) with 5-aminoisophthalic acid (5AIPA) in dry N,N-dimethylacetamide (DMAc). A series of novel polyesters (PE)s containing phthalimide group was prepared by the reaction of diacid monomer 5 with several aromatic diols via direct polyesterification with the tosyl chloride/pyridine/dimethylformamide (DMF) system as a condensing agent. The resulting new polymers were obtained in good yields with inherent viscosities ranging between 0.37 and 0.61 dL g⁻¹ and were characterized with FT-IR, ¹H NMR, elemental and thermogravimetric analysis techniques. These polymers are readily soluble in amide type solvents such as DMAc, DMF, 1-methyl-2-pyrrolidone, hexamethyl triaminophosphine, dimethyl sulfoxide and protic solvents such as sulfuric acid. Thermogravimetric analysis showed that the 10% weight loss temperature in a nitrogen atmosphere was more than 345 °C, which indicates that the resulting PEs have a good thermal stability as well as excellent solubility.     

Synthesis and characterization of sulfonated naphthalenic polyimides based on 4,4′-diaminodiphenylether-2,2′-disulfonic acid and bis[4-(4-aminophenoxy)phenylhexafluoropropane] for fuel cell applications

The paper describes the synthesis and characterization of sulfonated polyimides based on 1,4,5,8-naphthalene tetracarboxylic dianhydride (NTDA), 4,4′-diaminodiphenylether-2,2′-disulfonic acid (ODADS) and (bis[4-(4-aminophenoxy)phenylhexafluoropropane] (BDAF)). Several copolymer samples were prepared by varying the molar ratio of ODADS: BDAF (0.5:1.50, 0.75:1.25, 1:1 and 1.50: 0.5) in the initial monomer feed. Structural characterization of the copolymers was done using FT-IR and ¹H NMR. ¹H NMR was also used to calculate the copolymer composition. Thermal characterization was done using thermogravimertry and dynamic mechanical analysis. Polymer films were prepared by solution casting using m-cresol as solvent. The membranes thus prepared were characterized for water uptake, water stability, methanol permeability and proton conductivity. The obtained sulfonated polyimides (SPI’s) had proton conductivities in the range of 0.137-3.94 mS/cm. SPI’s with 50% degree of sulfonation had proton conductivity comparable to that of Nafion with methanol permeability lower than that of Nafion. It was found that the degree of sulfonation of polyimide had a large effect on the thermal stability, water uptake, ion-exchange capacity and proton conductivity.     

Oxazepines and thiazepines. XIX Synthesis of optically active 2,3-dihydro-1,5-benzothiazepin-4(5H)-ones

Optically active 2,3-dihydro-1,5-benzothiazepin-4(5H)-ones (14–17) have been synthesizedvia resolution and chemical transformation of nitrocarboxylic acids6–9. Starting from the latter various optically active substances have been synthesized as well. Optical purity was checked by NMR spectroscopy.Dedicated to Prof. Dr.G. Snatzke on the occasion of his 60th birthday.     

Synthesis of optically active polymers bearing amino acid moieties by atom transfer radical polymerization

We report here an approach toward the synthesis of optically active polyacrylamide bearing amino acid moieties, poly[N- methacryloyl L-leucine methyl ester] (PMALM), with controlled average number molecular weight (Mn) and relatively narrow polydispersity index (PDI, Mw/Mn < 1.3) by atom transfer radical polymerization (ATRP) using initiating system methyl 2- bromopropionate/CuBr/tris(2-dimethylaminoethyl) amine. The optical properties of the resulting polymers were evaluated fromspecific optical rotation value and CD spectra.     

Eco-friendly fast synthesis and thermal degradation of optically active polyamides under microwave accelerating conditions

<正>An optically active bulky aromatic diacid chiral monomer,(2S)-4-[(4-methyl-2-phthalimidylpentanoyl-amino) benzoylamino]isophthalic acid(1),containing a rigid phthalimide and flexible L-leucine pendent group was synthesized in five steps.A fast and clean method for direct polyamidation reaction of monomer 1 with various aromatic diamines under microwave irradiation and conventional heating was performed.The polymerization reactions provided optically active polyamides with high yields and inherent viscosities in the range of 0.36-0.74 dL/g.Their thermal properties were evaluated by thermogravimetric analysis(TGA) and differential scanning calorimetry.TGA thermograms show that the polymers are thermally stable,10%weight loss temperatures are in excess of 385℃,and char yields at 800℃are higher than 56%.The data obtained from TGA were used to study the kinetics of thermal decomposition of the resulting polymers. The interpretation of kinetic parameters(E,ΔH,ΔS andΔG) of thermal decomposition stages was evaluated using Coats and Redfern equation.     

Synthesis and characterization of new soluble and thermally stable aromatic poly(amide-imide)s based on N-[3,5-bis(N-trimellitoyl)phenyl]phthalimide

A new dicarboxylic acid, N-[3,5-bis(N-trimellitoyl)phenyl]phthalimide (1a), bearing three preformed imide rings was synthesized from the condensation of N-(3,5-diaminophenyl)phthalimide and trimellitic anhydride in glacial acetic acid at 1:2 molar ratio. For study of structure-properties relationship 1,3-bis(N-trimellitoyl)benzene (1b, as a reference) was also synthesized in a similar manner. 1a and 1b were characterized by spectroscopic methods and elemental analyses.A series of wholly aromatic poly(amide-imide)s with inherent viscosities of 0.63-1.09 dl g⁻¹ was prepared by triphenyl phosphite-activated polycondensation from the triimide-dicarboxylic acid 1a and the reference monomer 1b with various aromatic diamines. All of the polymers were fully characterized by FT-IR and ¹H NMR spectroscopy. The effects of the phthalimide pendent group on the polymers properties such as solubility, crystallinity, and thermal stability were investigated by comparison of the polymers. The polymers obtained from triimide-dicarboxylic acid 1a exhibited excellent solubility in a variety of solvents such as N-methyl-2-pyrrolidone, N,N-dimethylacetamide, N,N-dimethylformamide, and dimethylsulfoxide. These poly(amide-imide)s possessed glass-transition temperatures from 334 to 403 °C and exhibited excellent thermal stabilities and had 10% weight losses from 541 to 568 °C under a nitrogen atmosphere. Poly(amide-imide)s containing phthalimide pendent groups showed higher solubility, higher T_g and T_d10% values than those having no phthalimide pendent groups.     

Synthesis and characterization of polyamides obtained from tartaric acid and L-lysine

Two sets of AA · BB-type polyamides (PLyTA) were synthesized from natural compounds L-lysine and D- or L-tartaric acid via the active ester polycondensation method. The carboxyl and hydroxyl side groups were orthogonally protected as methyl ester and methyl ether, respectively. Direct reaction of methyl L-lysinate dihydrochloride with bis(pentachlorophenyl) di-O-methyl tartaric acid led to the aregic polyamide ar-PLyTA, whereas isoregic (ir-PLyTA) and syndioregic (sr-PLyTA) polyamides were obtained by polycondensation of specifically designed amide–aminoacid and amide–diamine monomeric precursors, respectively. These polyamides have intrinsic viscosities in the 0.50–0.76 dl g⁻¹ range, display optical activity, and are readily soluble in chloroform. They start to decompose well above 200 °C and display glass-transition temperatures at 100–105 °C. DSC and X-ray diffraction results indicated that these polyamides are not crystalline but they seem to adopt a partially ordered phase. No differences in properties other than optical rotation were observed between PLyTA made of D- and L-tartaric acid.     

Synthesis and characterization of optically active and organosoluble poly(amide-imide)s containing imidazole rings as pendent groups by direct polycondensation

Six new optically active poly(amide-imide)s(PAIs) 6a-f were prepared by direct polycondensation reaction of N-trimelli-tylimido-L-histidine 4 as a chiral diacid with various aromatic diamines 5a-f.Triphenyl phosphite(TPP)/pyridine(Py) in the presence of calcium chloride(CaCl2) and N-methyl-2-pyrrolidone(NMP) were successfully applied to direct polycondensation reaction.The resulting new polymers were in good yields,and had inherent viscosities ranging between 0.29 and 0.41 dL g-1 and were detected with elem...     

Synthesis of polyamides by direct polycondensation with (1,2-benzisoxazol-3-yl) diphenyl phosphate as a new activating agent

A new activating agent for amide condensations, (1,2-benzisoxazol-3-yl) diphenyl phosphate ( 1 ), was readily prepared in high yield by the reaction of 1,2-benzisoxazol-3-ol ( 2 ) with diphenyl phosphorochloridate ( 3 ) in the presence of triethylamine in benzene. The new activating agent 1 was found to be very useful for the preparation of amides from carboxylic acids and amines. The direct polycondensation of several dicarboxylic acids with aromatic diamines using the activating agent 1 in the presence of triethylamine proceeded slowly at room temperature to produce polyamides with inherent viscosities up to 1.2 dL g^?1.     

Synthesis of optically active fluoroadamantane derivative having different substituents on its tert-carbons and its use as a non-racemizable source for new optically active adamantane derivatives

Enantiomerically pure methyl 3-fluoro-5-methyladamantane-1-carboxylate was obtained by the separation of its racemate, which was prepared from methyladamantane-1-carboxylate in three steps in 86% overall yield. From the resulting pure enantiomers, a new optically active adamantane compound was prepared by the substitution of a fluorine atom with a phenyl group. Both enantiomers of 3-amino-5-methyladamantane-1-carbooxylic acid were also prepared.     

Stereospecific radical polymerization of optically active (S)-N-(2-hydroxy-1-phenylethyl) methacrylamide catalyzed by Lewis acids

The effects of Lewis acids, namely, rare earth metal trifluoromethanesulfonates, on the radical polymerization of (S)-N-(2-hydroxy-1-phenylethyl) methacrylamide were examined under various conditions. In the absence of Lewis acids, syndiotactic-rich polymers (r = 84%) were obtained, whereas in the presence of a catalytic amount of Lewis acids, the polymerization proceeded in an isotactic-specific manner (m up to 64%). Polymerization solvents strongly influenced the effect of the Lewis acids. The polymerization in n-butyl alcohol showed the highest isotactic selectivity, whereas the polymerization in DMSO showed no isotacticity-enhancing effect. Further increases in the Lewis acid concentration and the polymerization temperature did not produce clear effects on the tacticity of the polymers. The interaction between the monomer and Lewis acids was investigated, and the plausible mechanism of stereocontrol in the radical polymerization of (S)-HPEMA was analyzed based on the Lewis acid-monomer interaction.     

Synthesis and characterization of a novel high thermally stable energy compound： 1-（1-Adamantylamino）-2,4,6-trinitrobenzene

1-（1-Adamantylamino）-2,4,6-trinitrobenzene （1） as a potential energy material has been synthesized in excellent yield and characterized by FT-IR, 1H NMR and single crystallographic methods, and is thermally stable, decomposed in the range of 215- 72℃.