An optically pumped nanophotonic InP/InGaAlAs optical amplifier integrated on a SOI waveguide circuit

A small footprint integrated optical amplifier on Silicon-on-insulator is proposed in this article. By choosing to use optical pumping to drive the device, electrical contacting is avoided and the active waveguide can be made as thin as 100?nm, maximizing the optical confinement in the quantum well layers. Furthermore, the optical pumping is done through the silicon waveguide layer to optimally use the pump light. This leads to a compact device with high gain. We show 8?dB gain in pulsed regime in a 100?μm long device using a peak pump power of only 4.5?mW, while a comparable gain using an electrically pumped device would require an order of magnitude higher power consumption. This is an important step towards a CMOS-compatible optical amplifier for intra-chip optical interconnects.     

密集波分复用系统中光纤喇曼放大器的分析方法

本文利用耦合波理论分析了密集波分复用系统中具有一定光谱宽度的光信号之间的SRS相互作用规律,给出了宽光谱光抽运的光纤喇曼放大器的分析方法.     

Tm-doped Fiber Amplifier with Supercontinuum Output

We build a Tm-doped fiber amplifier based on a gain-switched seed laser. At Er-doped fiber-laser pumping, the maximum peak power of the gain-switched seed pulse is 227.7 W with a pulse duration of 48.3 ns. In the amplifier, peak power of the amplified pulse reaches 1.1 kW with a 3 dB linewidth of 0.06 nm. Supercontinuum generation is observed when this amplified pulsed laser source is injected into a section of 7 m long Tm-doped double-clad fiber.     

抽运光谱宽度对喇曼光纤放大器的影响

采用受激喇曼散射（SRS）耦合波理论分析了抽运光谱宽度对喇曼光纤放大器的影响, 指出当采用宽光谱作抽运光时会降低抽运效率. 同时, 文中还给出了抽运光谱宽度、抽运光功率和抽运效率间的变化规律曲线, 得出当传输光纤的有效截面积越小、喇曼增益系数越大、抽运光的入纤功率和光谱线宽度越大时, 光谱抽运效率越小的结论.     

Yb-Bi pulsed fiber lasers

A new type of pulsed fiber laser is suggested and developed - Yb-Bi lasers. In such lasers the Yb fiber laser is Q-switched by use of a saturable absorber, a Bi-doped fiber placed in its own resonator, and pulsed lasing is obtained in both fiber lasers. Continous-wave diode-clad pumping of the Yb-Bi lasers at a 975 nm wavelength with power up to 16.5 W results in pulsed laser action in a spectral diapason of 1050-1200 nm with a maximum pulse energy of up to 100 microJ, an average power up to 7.5 W, and a repetition rate up to 100 kHz.     

覆盖可见光波长的掺Er光纤飞秒光学频率梳

飞秒光学频率梳波长覆盖范围向可见光波长扩展对于碘稳频激光的绝对频率测量以及光钟研究中钟激光的绝对频率测量都具有十分重要的意义. 本文在自行研制掺Er光纤飞秒光学频率梳的基础上, 采用放大-倍频-扩谱的方案, 实现了激光输出波长向可见光波长的扩展. 掺Er光纤飞秒光学频率梳输出的一部分光激光脉冲, 功率约为8 mW, 首先经掺Er光纤放大器将功率提高到531 mW, 此后利用MgO: PPLN晶体倍频, 倍频后激光的功率为170 mW, 倍频效率为32%, 脉冲宽度为85 fs. 倍频后的激光通过光子晶体光纤进行光谱展宽. 通过优化入射光偏振状态可以实现波长覆盖500-1000 nm, 输出功率为85 mW, 耦合效率为50%. 采用小型化碘稳频532 nm Nd: YAG激光器输出激光与光学频率梳光谱展宽后的激光进行拍频可以获得30 dB的拍频信号. 覆盖可见光波长的掺Er光纤飞秒光学频率梳为可见光范围内激光的绝对频率测量提供了技术手段.     

高功率光子晶体光纤放大器实验研究

利用掺Yb³⁺的光子晶体光纤作为光纤放大器的增益介质,采用反向抽运方式,分别从理论和实验方面研究了不同信号的增益特性,在信号光功率为6W,抽运光功率为160W时,获得了104W的输出功率.实验发现,当抽运功率大于一定值时,放大器输出会有一定的不稳定性,并影响输出功率的进一步提高. 关键词： 光子晶体光纤 光纤放大器 反向抽运 高功率     

同带抽运高效率光纤放大器

以光纤光栅为谐振腔搭建了波长为1020 nm的光纤激光器,并通过两级级联放大获得了590 mW的最大输出功率. 利用获得的波长为1020 nm的激光进行了波长为1064 nm种子光同带抽运放大,实验研究了不同增益光纤长度时放大器的输出功率和转换效率. 当增益光纤长度为8.5 m时,放大器最大输出功率为385 mW,斜率效率为81%. 进行了波长为976 nm的半导体激光器直接抽运波长为1064 nm种子光的实验. 在增益光纤长度最优时,其斜率效率为56.4%. 实验结果表明,同带抽运方式比传统抽运方式具有更高的转换效率. 研究结果可为波长为1020 nm的激光高功率放大和波长为1064 nm的光纤激光高功率同带抽运放大提供一定的参考. 关键词： 同带抽运 光纤放大器 斜率效率     

Ultra-broadband amplified spontaneous emission source by using heterogeneous optical amplifier

In this work, we propose and experimentally investigate an ultra-broadband amplified spontaneous emission (ASE) light source with 113.8 nm bandwidth (1446.2 to 1560.0 nm) by using a cascaded two-stage optical amplifier, which is consisted of semiconductor optical amplifier (SOA, 1st stage) and erbiumdoped fiber amplifier (EDFA, 2nd stage), when the output intensity is above ?35 dBm/0.01 nm. And, the EDFA only uses a 3 m long erbium-doped fiber (EDF) with a 27 mW pumping power and SOA is driven at 200 mA bias current. Moreover, the proposed amplifier also can provide a broadband gain amplification of 114 nm in the wavelengths of 1464.0 and 1578.0 nm with the noise figure distribution of 6.8 to 8.1 dB.     

掺Er3+飞秒光纤放大器的特性研究

依据二能级速率方程和光传输方程,理论计算了Er3+光纤放大器中Er3+光纤的最佳长度Lc. 以全光纤飞秒激光器输出的孤子脉冲作为种子源,以理论值Lc作为实际采用的光纤长度,实验测量了Er3+光纤放大器在同向泵浦和反向泵浦下信号光的输出功率,得到同向泵浦的增益为20.0dB, 反向泵浦的增益为20.2 dB.同时测量了脉冲宽度随泵浦功率的变化,实验结果表明,随着泵浦功率的增大,输出光脉冲的宽度的压缩效应经历逐渐增强后逐渐减弱的过程.在同向泵浦方式下,可以得到更短的输出脉宽,其最短脉冲宽度为260 fs.     

Impacts of seed power on amplification performance in pulsed double-clad fiber amplifier

A pulsed master-oscillator fiber power amplifier system with near diffraction-limited output by use of China-made large-mode-area fiber and a （2 ＋ 1） × 1 multimode combiner is reported. The effect of the seed power on the amplification performance is found. For the seed power, there exists a range within which the pulsed fiber amplifier can operate safely and reliably at a certain pump power. With the seed average power of 70 mW, the amplification performances of the fiber amplifier are investigated.     

32 W百兆赫兹高重频可调谐单频激光光源

通过对连续种子光源的光强调制,并利用光纤放大器和固体介质放大器结合的混合放大方式,实现了百兆赫兹高重频可调谐单频激光光源。系统在基模输出条件下的最大输出功率为31.9 W,光束质量因子小于1.5,脉冲重复频率达到100 MHz,脉宽1 ns,测量得到的光束线宽小于0.8 GHz。实验结果验证了通过对连续光源进行光强调制获得高重频脉冲光源的可行性,并验证了混合放大方式是获得功率放大的一种有效手段。     

(1+1)型长距离侧面泵浦光纤实现17.4 kW激光输出

长距离侧面泵浦激光光纤在泵浦光注入、热管理、非线性抑制等方面具有天然优势,是实现高功率激光输出的有效途径。研制了（1+1）型长距离侧面泵浦激光光纤,采用1018 nm同带泵浦反向注入方式实现了17.4 kW激光输出,斜率效率为82.1%,3 dB线宽为1.3 nm,拉曼抑制比为37.8 dB。研究结果展示了长距离侧面泵浦光纤作为数十千瓦光纤激光放大器增益介质的巨大应用潜力。     

1410 nm波段分布式光纤拉曼增益放大器的研究

讨论了分布式光纤拉曼增益放大器的工作原理,采用1320nm固体激光器作为抽运源,获得了1410nm波段附近的光放大,在单模GI光纤长度为23km时,初步研究了拉曼放大器增益与光纤作用长度的关系,抽运脉冲峰值功率分别为50W、30W时,光纤的有效作用长度分别为15．5km和10.5km;研究了在不同的光纤有效作用长度时,拉曼放大器增益与抽运功率的关系;从光纤拉曼光谱图估算了光纤拉曼放大器的光谱宽度为50nm或250cm^-1。     

高浓度镱铒共掺磷酸盐光纤放大器增益特性

在忽略高能级的自发辐射和光纤损耗的情况下，利用速率方程和传输方程理论研究了高浓度Er³⁺/Yb³⁺共掺磷酸盐玻璃光纤放大器的增益特性，讨论了Er³⁺浓度、Yb³⁺浓度、抽运光功率、信号光功率、光纤长度对放大器增益的影响，并与单掺铒光纤放大器进行了比较.由于Yb³⁺的敏化作用降低了铒离子的团簇效应，减少了离子间相互作用，共掺光纤的增益和效率明显高于单掺光纤.数值计算表明，3.2cm长Er³⁺/Yb³⁺共掺光纤在980nm的20dBm(100mW)抽运功率下，1532nm处的增益可达10dB. 关键词： 镱铒共掺光纤放大器 速率方程 传输方程 高浓度     

双包层掺染料聚合物光纤放大器的增益性能分析

双包层聚合物光纤放大器可以减小染料的热漂白,使用速率方程的方法,给出了一个能够全面描述双包层掺染料聚合物光纤放大器增益性能的模型,模型既考虑了染料三重态能级对速率方程的影响,又考虑了双包层结构对泵浦光的影响,可以在稳态的情况下计算放大器的各种增益性能指标.     

Pulsed degenerate optical parametric oscillator based on a nonlinear-fiber Sagnac interferometer

We report operation of an all-fiber degenerate optical parametric oscillator that employs a nonlinear-fiber Sagnac interferometer as a parametric amplifier. Synchronous pumping with 3.9-ps pulses at 1544 nm yields 0.83-ps output pulses. The wide bandwidth of the fiber parametric amplifier causes the oscillator to act as a pulse compressor. The output signal pulses exhibit improved spectral symmetry and a reduced time-bandwidth product compared with the pump pulses. Currently, the net group-velocity dispersion in the passive section of the fiber cavity limits the signal-pulse bandwidth and hence the minimum-obtainable pulse width. This experiment suggests the possibility of frequency conversion by operation of a similar pulsed parametric oscillator away from degeneracy.     

光子晶体光纤放大器增益特性的实验研究

 采用掺Yb³⁺双包层光子晶体光纤作为放大器的增益介质,在双端泵浦方式下,理论并实验研究了不同信号光时放大器的增益特性。在双端泵浦方式下,泵浦总功率为150.2 W、信号光功率为6 W时,获得了72 W的功率输出,斜率效率达到了60%。实验发现当泵浦总功率超过一定值时,由光纤端面反射形成的振荡腔引起放大器寄生振荡,并由于各种非线性效应出现了自脉动现象,影响了输出功率的进一步提高。     

All-fiber eye-safe pulsed laser with Er-Yb Co-doped multi-stage amplifier

We report an all-fiber pulsed laser with multistage fiber amplifier which was suitable for high power eye-safe free space optical communications. Tapered structure has been utilized between booster and final amplifiers, which could increase the power coupling from the former fiber into the core of the latter fiber, and the beam quality of the output laser could be improved simultaneously. A maximum output power over 6 W has been achieved from the master-oscillator-power-amplifier system. With the multi-stage configuration and forward pumping, the optical signal to noise ratio was measured to be better than 50 dB.     

2μm single-frequency master-oscillator fiber power amplifier

We report a single frequency laser source consisting of a Tm:YAP coupled-cavity master-oscillator and a Tm-doped fiber power amplifier. The MOFPA yielded 4.55 W of single frequency output at 1990 nm when the input signal was 270 mW and the pumping power was 35.2 W. A strong amplification of spontaneous emission (ASE) was observed when higher pumping power was applied. Therefore, the output power of the single frequency fiber power amplifier was limited by the input power of seed laser.