An electrically tunable metasurface integrated with graphene for mid-infrared light modulation

We propose a low-cost plasmonic metasurface integrated with single-layer graphene for dynamic modulation of midinfrared light. The plasmonic metasurface is composed of an array of split magnetic resonators(MRs) where a nano slit is included. Extraordinary optical transmission(EOT) through the deep subwavelength slit is observed by excitation of magnetic plasmons in the split MRs. Furthermore, the introduction of the slit provides strongly enhanced fields around the graphene layer, leading to a large tuning effect on the EOT by changing the Fermi energy of the graphene. The proposed metasurface can be utilized as an optical modulator with a broad modulation width(15 μm) or an optical switch with a high on/off ratio( 100). Meanwhile, the overall thickness of the metasurface is 430 nm, which is tens of times smaller than the operating wavelength. This work may have potential applications in mid-infrared optoelectrical devices and give insights into reconfigurable flat optics and optoelectronics.     

Characterization of the signature of subwavelength variation from far-field irradiance

The dynamic signature of the subwavelength variation of a slit is shown to be determinable from far-field irradiance with a precision of better than 1 nm. One can increase the efficiency of measurement of the subwavelength's signature by adjusting the detection width over which the subwavelength variation is detected. The subwavelength variation of a rectangular aperture was also examined to show the general feasibility.     

Remarkable zeroth-order resonant transmission of microwaves through a single subwavelength metal slit

A slit in a thick metal plate that is extremely subwavelength will not transmit microwaves polarized parallel to it. It is shown here that cuts perpendicular to the slit allow parallel polarized radiation to resonantly transmit. Furthermore, a zero-order mode may be excited within the slit, the frequency of which, to first order, is independent of the plate depth. Remarkably, for this novel type of resonance, the field in the slit oscillates with a constant phase and little amplitude variation throughout the plate depth, while the resonant wavelength tends to infinity as the slit width approaches zero.     

Systematic study on visible light collimation by nanostructured slits in the metal surface

We present a systematic experimental investigation on visible light collimation by a nanostructured slit flanked with a pair of periodic array of grooves in gold thin film. A wide variety of aspects are considered, such as the polarization state, the transport path of incident light, the groove--groove spacing, the groove width and depth. Our results clearly show that the relationship between the collimation wavelength and the periodicity of the slit-groove structure accords well with the surface plasmon dispersion model proposed by previous researchers. Furthermore, the surface plasmon wave phase retardation effect induced by the surface structure is also verified via the measurement for samples with different groove widths and depths. These results indicate that the detailed geometry of the groove structure has obvious impacts on the collimation effect and the angular distribution of the diffraction light in the subwavelength plasmonic system.     

Finite conductance governs the resonance transmission of thin metal slits at microwave frequencies

Fabry-Perot-like resonant transmission of microwave radiation through a single subwavelength slit in a thick aluminum plate is quantified for a range of slit widths. Surprisingly, and in contrast to previous studies [e.g., Phys. Rev. Lett. 86, 5601 (2001)]], the resonant frequency exhibits a maximum as a function of slit width, decreasing as the slit width is reduced to less than 2% of the incident wavelength. This result accords with a new model based on coupled surface plasmon theory taking into account the finite conductivity, and hence permittivity, of the metal. This is contrary to a common assumption that metals can be treated as infinitely conducting in this regime.     

单色仪波长定标中狭缝设置的影响分析

单色仪作为一种分光仪器，在传感器的辐射定标等方面具有重要应用。在实际应用过程中，其波长和带宽的设置对传感器的精确定标具有重要影响。使用低压汞灯作为波长标准光源，通过对其特征谱线扫描的方法，研究了传感器定标过程中，设置单色仪不同的狭缝宽度，对传感器精确定标具有重要影响。结果显示，当出射入射狭缝相同，同时改变其宽度的情况下，与典型校准状态(出射入射狭缝宽度设置为0.5 mm)相比，波长偏差量达到0.17 nm；当入射狭缝与出射狭缝不一致时，与典型校准状态相比，波长偏差量达到0.18 nm；当光源未充满入射狭缝与充满入射狭缝相比，最大误差达到0.02 nm，该影响几乎可以忽略。在相关的传感器光谱辐射定标实验研究中，单色仪的定标精度和准确性评估等方面具有重要应用。     

Enhanced optical reflection and multiple-peak transmission from a subwavelength slit with surface corrugations

We have observed a new phenomenon of the enhanced optical reflection and transmission from a subwavelength metallic slit with surface corrugations. The reflected energy is focused by the periodic structure and our experiment shows that it is more effective than a planar metal surface in real situations. The transmission spectrum performs the feature of a multipeak narrow-band transmission with a wavelength spacing of 1.4 nm resulting from the FP cavity resonance in the substrate film. Such optical response properties of our sample will be very useful for applications in many fields including wavelength-division-multiplexing (WDM) optical communications systems.     

Transmission through array of subwavelength metallic slits curved with a single step or mutli-step

The transmission of normally incident plane wave through an array of subwavelength metallic slits curved with a sin- gle step or mutli-step has been explored theoretically. The transmission spectrum is simulated by using the finite-difference time-domain method. The influences of surface plasmon polaritons make the end of finite long sub-wavelength metallic slit behaves as magnetic-reflecting barrier. The electromagnetic fields in the subwavelength metallic slits are the superpo- sition of standing wave and traveling wave. The standing electromagnetic oscillation behaves like LC oscillating circuit to decide the resonance wavelength. Therefore, the parameters of adding step may change the LC circuit and influence the transmission wavelength. A new explanation model is proposed in which the resonant wavelength is decided by four factors： the changed length for electric field, the changed length for magnetic field, the effective coefficient of capacitance, and the effective coefficient of inductance. The effect of adding step is presented to analyze the interaction of two steps in slit with mutli-step. This explanation model has been proved by the transmission through arrayed subwavelength metallic slits curved with two steps and fractal steps. All calculated results are well explained by our proposed model.     

Analysis on polarization dependence of Fraunhofer diffraction by metallic grating with short period

A method based on the combination of finite-difference time-domain (FDTD) algorithm and Fourier transformation was proposed to analyze the Fraunhofer diffraction of gratings. Polarization dependence of the Fraunhofer diffraction of a one-dimensional metallic grating with period less than 8 times the incident wavelength was studied. Some special characteristics were found. The polarization dependence is related to period value, slit width, and thickness of the grating, and the missing orders predicted by scalar analysis appear. Besides, if the period of a grating is larger than 8 times the wavelength but the slit width or the size of the opaque portion of the grating is close to the wavelength, diffraction of the grating also becomes polarization dependent.     

Transmission of light through metallic Z-shaped slit array with inner metallic bar

The transmission of a normally incident wave through a Z-shaped channel metallic slit array with metallic bar inside has been investigated by using finite-difference time-domain method. It is obtained that transmission spectra are nearly the same of the slit array with straight channel as that with Z-shaped channel in the condition the material of the slit array the same as that of the inner bar. If the Au bar is replaced by Al of the Au slit array, both resonance modes red shift obviously, especially for the structure with bent channel. Along with the width of the inner bar increasing, the localized waveguide resonance mode red shifts regularly with a tiny decrease of the peak value of all the kinds of composed structure introduced here, and the surface plasmon resonance mode red shifts regularly accompanied by peak value changing uniformly for the structures with only one type of metal. However, the surface plasmon resonance behaves different obviously, its center peak first moves to a larger wavelength fast, then red shifts slowly, for the Au-film Al-bar structure, but that moves in a very small wavelength range for the Al-film Au-bar one. The results obtained here are helpful to design subwavelength optical devices.     

同步荧光光谱法测定石油中的晕苯

用苯做溶剂对原油样品进行逐级稀释,恒波长同步荧光法对原油样品中晕苯进行定性、定量分析。分别从溶剂选择、波长差、狭缝宽度等参数对其测定的光谱条件进行优化。实验结果表明：用苯为溶剂、Δλ=6nm,狭缝宽度为2.5nm,为原油样品中晕苯的最佳测试条件。所建立方法测定晕苯的线性范围为0.5—100μg/mL,校准曲线的相关系数r大于0.99,相对标准偏差小于3%（n=5）。该法分析快速、准确,对石化工厂中对原油样品中晕苯的快速检测具有一定的应用价值。     

Focusing of light beyond the diffraction limit of half the wavelength

The diffraction limit sets the smallest achievable linewidth at half the wavelength. With a subwavelength plasmonic lens allowing one to reduce the diffraction via an asymmetry and to generate and squeeze the wave functions, an incident light is focused by the aperture to a single line with its width smaller than the limited value in the intermediate zone. The focused fields are capable of propagating in free space. This light focusing process, besides being of academic interest, is expected to open up a wide range of application possibilities.     

Fabrication of integrated waveguide grating in azo polymers

In this Letter, we have introduced a technique, new to our knowledge, to fabricate gratings on a waveguide of azo-functionalized polymeric films using a slit mask and a fast, direct-writing method. To prevent the destruction of the waveguide by the grating formation on the waveguide, we placed a slit mask on the waveguide. By properly adjusting the resonance, this grating can be used as an integrated wavelength filter. We have produced an attenuation of 13.4?dB at 1562?nm with a FWHM of 3.45?nm. The grating has been fabricated as narrow as the width of the waveguide to couple filtered light into the waveguide by using a slit mask. Any light shifted from the resonance will pass through the waveguide undisturbed.     

Plasmonic tomography of optical vortices

We present a method for analyzing the wavefront of optical vortices that does not involve interferometry but rather uses surface plasmon polaritons (SPPs). We employ a subwavelength slit in a gold film to cut slices from an optical vortex beam and measure the diffraction of the generated SPPs by scattering them off a second slit. By moving the slits across the vortex beam, we create a tomogram, from which we can determine the vortex charge of the incident beam at a glance. We present results for vortex beams of integer- and half-integer-vortex charge.     

Lecture Demonstration of Fresnel Diffraction by a Slit and Half-Plane

In the present work, lecture demonstration of Fresnel diffraction by a slit and half-plane with the use of modern scientific means of optical experimentation is described. The developed software allows light diffraction to be modeled on a personal computer depending on the wavelength, slit width, and distance from the slit (half-plane) to the screen and simultaneously a graphic method of calculating the field amplitude with the help of the Cornu spiral to be demonstrated. A photodetector system built around a video camera controlled by a personal computer is used to register an actual diffraction pattern. The experimental intensity distributions are compared with the theory. The integrated approach allows the efficiency of comprehension of complex diffraction phenomena in wave optics to be increased. __________ Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 6, pp. 9–15, June, 2005.     

Subwavelength lithography using metallic grating waveguide heterostructure

We present subwavelength periodic gratings achieved by employing a metallic grating waveguide heterostructure (MGWHS). The mask can be designed to make one of its diffraction order (±mth) waves resonate with the surface plasmon wave supported by the MGWHS. With a finite-difference time-domain method, we numerically demonstrate that one-dimensional periodic structure of about 60 nm feature, which is far beyond the diffraction limit, can be patterned with the interference of the 3rd diffraction order waves of the mask at a wavelength of 546 nm. The technique can also be extended to two-dimensional patterns using circularly polarized incidence and for the incidence with an angle θ.     

Trapping of surface-plasmon polaritons in a subwavelength cut

We study a transverse magnetic wave propagation in a subwavelength metallic slit which is modified by a perpendicular cut. The surface-plasmon polaritons (SPPs) can be trapped in the perpendicular cut by tuning the length or width of the cut. Moreover, the period of the resonance states corresponds to the difference of the cut's length ΔL which is 450 nm. An analytical solution for the resonance condition of the structure is derived by the cavity theory, which is consistent with the numerical simulation by using the finite difference time domain (FDTD) method.     

极紫外平场光栅光谱仪的研制和性能测试

研制了一台高分辨率极紫外光谱仪,用于磁约束等离子体诊断。采用一块具有平场特性的全息球面变线距光栅作为分光元件,光栅公称线密度为1 200 lines·mm-1,掠入射角为3°。一台可深度制冷、背照式面阵CCD作为光谱探测器,用机械快门控制曝光时间。通过CCD在光谱聚焦面的移动,可以记录的光谱范围为5～50 nm。用Penning放电光源测试了光谱仪的性能; 利用光源的标准谱线,进行了波长标定,波长精度为0.003 nm,并计算出系统各参数的实际值;当入缝宽度设置为30 μm时,在20 nm附近,光谱分辨率达0.015 nm,达到设计指标。     

基于SPPs-CDEW混合模式的亚波长单缝多凹槽结构全光二极管

全光二极管是集成光子回路上最基本的光子器件,如何有效增强全光二极管的单向透射性,提高消光比一直是学者们研究的重点.当前,利用表面等离极化激元(surface plasmon polaritons,SPPs)和复合衍射衰逝波(composite diffracted evanescent wave,CDEW)的亚波长金属微纳结构构建全光二极管器件还鲜有研究.因此,开发出一种可调制的全光二极管,对未来制备复杂的光子回路具有重要意义.本文提出了一种基于SPPs-CDEW混合模式设计全光二极管的方法和结构,该结构结合纳米缝中的类法布里-珀罗共振效应,利用结构参数对SPPs进行调控,实现了光束单向透过的功能.首先,利用理论推导和有限元算法分析了单缝-对称双凹槽纳米结构的透射增强现象,提出了透射增强和削弱的物理机理.其次,计算出规约化透射率随单狭缝和凹槽对之间距离变化的远场透射谱,给出的理论和数值计算结果符合得很好.最后,通过此透射谱精确确定凹槽的位置和数量,得出上表面对称分布五对增强透射凹槽、下表面六对抑制透射凹槽的最优全光二极管结构,有效增强了全光二极管的单向透射性,提高了消光比,最大消光比可以达到38.3 dB,即正向透射率是反向透射率的6761倍,比已有文献提高了14.6 dB,并在850 nm左右有70 nm宽的工作波长带宽(20 dB).本文提出的光二极管结构简单,宽带宽工作,易于集成,耦合效率高,研究结果对光学信号传输、集成光回路、超分辨率光刻等相关领域具有潜在的应用价值.     

Wideband plasmonic beam steering in metal gratings

We demonstrate controllable light deflection in thick metal gratings with periodic subwavelength slits filled with an active material. Under specific illumination conditions, the grating becomes nearly transparent and acts as a uniform optical phased-array antenna where the phase of the radiating elements is controlled by modifying the index of refraction of the material that fills each slit. The beam-steering operational regime occurs in a wide wavelength band, and it is relatively insensitive to the input angle.