Ammoxidation of 3- and 4-picolines over V2O5?SnO2/γ?Al2O3 catalyst

The ammoxidation of 3- and 4-picolines has been studied over V₂O₅–SnO₂/–Al₂O₃ catalysts prepared by surface impregnation technique. Best results were obtained for the generation of cyanopyridines in the temperature range 400–450°C and sub-stoichiometric value with respect to O₂. Catalysts that were calcined above 700°C showed no activity.

---

3- 4- V₂O₅–SnO₂/–Al₂O₃, . 400–450°C O₂. , 700 K, .

     

Doping of CoMo?Al2O3 catalyst with Mg and Zn

Effect of Mg (Zn) addition to CoMo–Al₂O₃ catalyst on its activity in hydrogenation of toluene and HDS of thiophene has been determined. These additives decrease the catalyst activity and modify the mechanism of thiophene HDS.

---

Mg (Zn) CoMo/Al₂O₃ () . .

     

Physicochemical properties and hds activity of CoMo?P?Al2O3 catalysts

Porous structure, acidity and hds activity of the CoMo–P–Al₂O₃ catalysts have been studied. Phosphorus was introduced jointly with molybdenum. This method of phosphorus incorporation gave substantial diminution of surface area, moderate changes of acidity and decrease in hds activity for the catalysts with P₂O₅ content higher than 5 wt.%.

---

, CoMo–P–Al₂O₃. . , P₂O₅ 5 .%.

     

Activity of Co?Mo catalysts supported on alumina modified with La2O3

Catalytic activity in the water-gas shift (WGS) reaction was measured over Co−Mo sulfides supported on alumina modified with La₂O₃. Increasing concentration of La₂O₃ up to 15% provides better catalytic performance and higher sorption capacity of ammonia.     

Reduction of an amorphous NiO?Al2O3/SiO2 catalyst by different olefins and hydrogen

By static magnetic measurements it was found that the ability to reduction of an amorphous NiO–Al₂O₃/SiO₂ catalyst decreases in the order: but-2-eneshydrogen isobutene>but-1-ene>propeneethene. The reduction temperatures are significantly higher than the dimerization reaction temperatures.

---

, NiO–Al₂O₃/SiO₂ : -2>-1> . .

     

Ni/Al2O3 catalysts for CO methanation: Effect of Al2O3 supports calcined at different temperatures

The correlation between phase structures and surface acidity of Al2O3 supports calcined at different temperatures and the catalytic performance of Ni/Al2O3 catalysts in the production of synthetic natural gas(SNG) via CO methanation was systematically investigated. A series of 10 wt% NiO/Al2O3 catalysts were prepared by the conventional impregnation method, and the phase structures and surface acidity of Al2O3 supports were adjusted by calcining the commercial γ-Al2O3 at different temperatures(600–1200 C). CO methanation reaction was carried out in the temperature range of 300–600 C at different weight hourly space velocities(WHSV = 30000 and 120000 mL·g-1h-1) and pressures(0.1 and 3.0 MPa). It was found that high calcination temperature not only led to the growth in Ni particle size, but also weakened the interaction between Ni nanoparticles and Al2O3 supports due to the rapid decrease of the specific surface area and acidity of Al2O3 supports. Interestingly, Ni catalysts supported on Al2O3 calcined at 1200 C(Ni/Al2O3-1200) exhibited the best catalytic activity for CO methanation under different reaction conditions. Lifetime reaction tests also indicated that Ni/Al2O3-1200 was the most active and stable catalyst compared with the other three catalysts, whose supports were calcined at lower temperatures(600, 800 and 1000 C). These findings would therefore be helpful to develop Ni/Al2O3 methanation catalyst for SNG production.     

Fe2O3/Al2O3氧载体制备方法的研究

采用溶胶-凝胶法、共沉淀法、水热合成法、低热固相合成法、机械混合法、燃烧合成法和冷冻成粒法制备铁基氧载体Fe₂O₃/Al₂O₃,并通过物理和化学表征手段来筛选和优化制备方法和制备工艺。对煅烧后的氧载体进行硬度测试,结果表明,溶胶-凝胶法、共沉淀法、机械混合法、燃烧合成法和冷冻成粒法制备的氧载体硬度较高;载体的X射线衍射(XRD)谱图表明,各种制备方法均能制得物相组成为Fe₂O₃/Al₂O₃的氧载体,且随着煅烧温度的提高、煅烧时间的延长,氧载体的结晶度、晶体粒径逐渐增大,煅烧温度1 200℃的氧载体的机械性能、晶体结构、晶相组成更稳定。借助化学吸附仪的程序升温还原(TPR)实验表征氧载体的反应活性,并计算氧载体活性度。综合物理和化学表征实验结果表明,最优制备方法为溶胶-凝胶法和冷冻成粒法。     

Ni/Al2O3催化甲烷裂解

分别通过浸渍法和共沉淀法制备了不同Ni负载量的Ni/Al2O3催化剂。考察了Ni负载量、制备方法以及反应温度对Ni/Al2O3催化甲烷裂解性能的影响。结果表明,在550℃,浸渍法制备的Ni/Al2O3催化剂,当Ni负载量为20%(质量分数)、Ni金属平均粒径为11.25 nm时,具有最佳的甲烷催化裂解效果,其每摩尔Ni的氢气产量和每克Ni碳产量分别为164 mol和15.30 g。催化剂制备方法对Ni/Al2O3甲烷催化裂解反应有显著影响,相同Ni负载量共沉淀法制备的Ni/Al2O3甲烷催化裂解总体效果要好于浸渍法制备的Ni/Al2O3,而且反应过程中生成的碳纤维较长,管径也较均一。550℃时,共沉淀法制备的Ni负载量为41.2%(质量分数)的Ni/Al2O3催化剂在反应至350 min时,仍保持着30%以上的转化率。     

Oxidative coupling of methane over Bi2O3?P2O5?K2O/Sm2O3

Oxidative coupling of methane over Bi₂O₃–P₂O₅–K₂O/Sm₂O₃ takes place giving more C₂H₄ as compared to C₂H₆. Sm₂O₃ supported Bi–P–K is a more active and selective catalyst, than TiO₂, -Al₂O₃, SiO₂ and MgO supported catalysts.

---

Bi₂O₃–P₂O₅–K₂O/Sm₂O₃ , . Bi–P–K, Sm₂O₃, , TiO₂, -Al₂O₃, SiO₂, MgO.

     

Michael addition of nitromethane to 3-buten-2-one catalyzed by potassium fluoride supported on Al2O3, ZnO, SnO2, sepiolite, AlPO4, AlPO4?Al2O3 and AlPO4?ZnO

The Michael addition of nitromethane to 3-buten-2-one has been carried out in the absence of solvent, using potassium fluoride supported on Al₂O₃, ZnO, SnO₂, sepiolite, AlPO₄, AlPO₄–Al₂O₃ and AlPO₄–ZnO catalysts. We found that KF/ZnO easily performed the Michael addition and thus, ZnO is a better support for the basic reagent than Al₂O₃. Besides, the Michael addition was not successful with AlPO₄ or AlPO₄-metal oxide acidic supports.

---

3--2- , , Al₂O₃, ZnO, SnO₂, , AlPO₄, AlPO₄–Al₂O₃ AlPO₄–ZnO. , KF/ZnO .. ZnO, , , Al₂O₃. , , AlPO₄ AlPO₄- .

     

MoO3/Al2O3催化氧化选择性合成亚砜

采用浸渍法制备了不同负载量的MoO3/Al2O3催化剂,讨论了MoO3,Al2O3和MoO3/Al2O3负载的催化剂作用下,利用H2O2进行硫醚氧化制亚砜的反应.结果显示MoO3/Al2O3催化剂负载量为20%时催化活性最高,原料转化率达100%,且没有副产物生成.将该方法应用到兰索拉唑前体的氧化反应中,收率达到80%.催化剂重复使用6次不失活.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33,用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体.采用这些固溶体作载体,以Fe2O3为活性组分,用浸渍法制备了一系列催化剂.BET结果显示,将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积.TPR结果显示,载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能.XRD结果表明,Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况,老化前后催化剂的晶相结构基本无明显变化.特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时,Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33, 用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体. 采用这些固溶体作载体, 以Fe2O3为活性组分, 用浸渍法制备了一系列催化剂. BET结果显示, 将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积. TPR结果显示, 载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能. XRD结果表明, Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况, 老化前后催化剂的晶相结构基本无明显变化. 特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时, Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

Al2O3助剂对Co/SiC催化剂F-T反应性能的影响

分别采用沉淀法、尿素水解法制备Al₂O₃/SiC复合载体,采用等体积浸渍法制备Co/Al₂O₃-SiC催化剂。结合N₂吸附、XRD、H₂-TPR、XPS等表征手段,研究Al₂O₃助剂对钴基催化剂物相结构、还原行为以及F-T合成性能等的影响。结果表明,氧化铝加入后增强了载体与钴物种之间的相互作用,提高了钴物种的分散度,降低了钴物种的还原度。尿素水解法引入Al₂O₃后,载体与钴物种具有适中的相互作用,表现出较高的反应活性。沉淀法制备的载体负载钴物种后由于较强的金属-载体相互作用,表现出较优的稳定性。     

Deuterium exchange reaction of ethylbenzene over an Fe2O3?K2CO3?Cr2O3 catalyst

Isotope exchange reaction of ethylbenzene with water or hydrogen has been examined over Fe₂O₃–K₂CO₃–Cr₂O₃ catalyst. The participation of the hydrogen attached to -carbon or phenyl group was observed. The exchange rate of the -hydrogen was compared for different alkylbenzenes and found that toluene was the most active, whereas cumene was inactive. This order suggested that the -hydrogen dissociated as a proton. -Adsorbed state was supposed as an intermediate of dehydrogenation, which dissociates the -hydrogen reversibly as a proton on a basic site. Including the results of exchange reaction of styrene, the overall route of dehydrogenation is discussed.     

助剂CeO2对Co/Al2O3催化剂上F-T合成反应性能的影响

在用于F-T合成的Co/Al     

Kinetic study of propane dehydrogenation and catalyst deactivation over Pt-Sn/Al2O3 catalyst

The kinetics of propane dehydrogenation and catalyst deactivation over Pt-Sn/Al2O3 catalyst were studied.Performance test runs were carried out in a fixed-bed integral reactor.Using a power-law rate expression for the surface reaction kinetics and independent law for deactivation kinetics,the experimental data were analyzed both by integral and a novel differential method of analysis and the results were compared.To avoid fluctuation of time-derivatives of conversion required for differential analysis,the conversion-time data were first fitted with appropriate functions.While the time-zero and rate constant of reaction were largely insensitive to the function employed,the rate constant of deactivation was much more sensitive to the function form.The advantage of the proposed differential method,however,is that the integration of the rate expression is not necessary which otherwise could be complicated or impossible.It was also found that the reaction is not limited by external and internal mass transfer limitations,implying that the employed kinetics could be considered as intrinsic ones.     

过渡金属修饰Fe2O3/Al2O3氧载体的Redox性能研究

采用冷冻干燥法分别制备了经Cu、Co、Mn、Ni修饰的Fe₂O₃/Al₂O₃氧载体。利用化学吸附仪,通过程序升温还原(H₂-TPR)和程序升温氧化(TPO)来研究经不同过渡金属修饰的Fe₂O₃/Al₂O₃与H₂和O₂的反应性能。实验发现,在Fe₂O₃/Al₂O₃中加入Cu、Co、Ni以后,氧载体与H₂的反应性都有提高,但是当在Fe₂O₃/Al₂O₃中加入Mn以后,氧载体的反应性和载氧能力反而下降。经Cu修饰的Fe₂O₃/Al₂O₃与H₂的反应性最高,且具有很好的反应稳定性,适合用于化学链燃烧。     

纳米膜组装介孔Al2O3：合成及Pt/Al2O3的硝基苯催化加氢性能

以"乙酸乙酯(EA)-偏铝酸钠-水"体系在室温下合成了纳米膜组装介孔Al2O3。研究发现:合成反应时间、静置前搅拌时间、NaAlO2用量、EA用量及反应温度等对合成产物的形貌有影响;另外,与用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂相比,纳米膜组装介孔Al2O3制备的Pt/Al2O3催化剂含有部分易被还原的PtOx物种。在硝基苯催化加氢反应中,用合成Al2O3为载体制备的Pt/Al2O3催化剂,比用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂具有更好的催化活性。