NHS-ester functionalized poly(PEGMA) brushes on silicon surface for covalent protein immobilization

Poly(PEGMA) homopolymer brushes were developed by atom transfer radical polymerization (ATRP) on the initiator-modified silicon surface (Si-initiator). Through covalent binding, protein immobilization on the poly(PEGMA) films was enabled by further NHS-ester functionalization of the poly(PEGMA) chain ends. The formation of polymer brushes was confirmed by assessing the surface composition (XPS) and morphology (atomic force microscopy (AFM), scanning electronic microscopy (SEM)) of the modified silicon wafer. The binding performance of the NHS-ester functionalized surfaces with two proteins horseradish peroxidase (HRP) and chicken immunoglobulin (IgG) was monitored by direct observation. These results suggest that this method which incorporates the properties of polymer brush onto the binding surfaces may be a good strategy suitable for covalent protein immobilization.     

Controlled one-step synthesis of a diblock copolymer

Well-defined block copolymers were obtained from 4-hydroxy-butyl-2-bromoisobutyrate dual initiator, combining tert-butylmethacrylate ATRP and ε-caprolactone ROP in a one-step process. Using AlEt₃ as coinitiator in a ROP catalytic process, the variation of the AlEt₃/initiator ratio permits to modulate the ROP rate and so to control the final block copolymer composition. Nevertheless, slight interferences between the two polymerizations were observed.     

Novel hydroxyethylcellulose-graft-poly acrylamide copolymer for separation of double-stranded DNA fragments by CE

A novel separation medium, hydroxyethylcellulose-graft-polyacrylamide (HEC-g-PAM) synthesized by atom transfer radical polymerization (ATRP), used for dsDNA separation by CE is presented. The separation performance of HEC-g-PAM, which has the same graft density and different graft length, has been investigated in Tris-boric acid-EDTA (TBE) buffer solvent mixtures. The temperature-dependent rheological behavior of HEC-g-PAM was also studied by steady-shear rheometry. The results showed that dsDNA fragments between 72 and 1353 bp was achieved with a 30 cm effective capillary length at 150 V/cm using this type of graft copolymer as a separation medium in bare fused-silica capillaries, and separation improvement is obtained in HEC-g-PAM compared with HEC and poly(dimethylacrylamide (PDMA).     

Preparation and characterization of a thermoresponsive gigaporous medium for high-speed protein chromatography

A high-speed thermoresponsive medium was developed by grafting poly(N-isopropylacrylamide-co-butyl methacrylate) (P(NIPAM-co-BMA)) brushes onto gigaporous polystyrene (PS) microspheres via surface-initiated atom transfer radical polymerization (ATRP) technique, which has strong mechanical strength, good chemical stability and high mass transfer rate for biomacromolecules. The gigaporous structure, surface chemical composition, static protein adsorption, and thermoresponsive chromatographic properties of prepared medium (PS–P(NIPAM-co-BMA)) were characterized in detail. Results showed that the PS microspheres were successfully grafted with P(NIPAM-co-BMA) brushes and that the gigaporous structure was robustly maintained. After grafting, the nonspecific adsorption of proteins on PS microspheres was greatly reduced. A column packed with PS–P(NIPAM-co-BMA) exhibited low backpressure and significant thermo-responsibility. By simply changing the column temperature, it was able to separate three model proteins at the mobile phase velocity up to 2167 cm h⁻¹. In conclusion, the thermoresponsive polymer brushes grafted gigaporous PS microspheres prepared by ATRP are very promising in ‘green’ high-speed preparative protein chromatography.     

Computer‐aided design and synthesis of magnetic molecularly imprinted polymers with high selectivity for the removal of phenol from water

A molecular simulation method was introduced to compute the phenol–monomer pre‐assembled system of a molecularly imprinted polymer. The interaction type and intensity between phenol and monomer were evaluated by combining binding energy and charge transfer with complex conformation. The simulation results indicate that interaction energies are simultaneously affected by the type of monomer and the ratio between phenol and monomers. At the same time, we considered that by increasing the amount of functional monomer is not always better for preparing molecularly imprinter polymers. In this study, three kinds of novel magnetic phenol‐imprinted polymers with favorable specific adsorption effects were prepared by the surface imprinting technique combined with atom transfer radical polymerization. Various measures were selected to characterize the structure and morphology to obtain the optimal polymer. The characterization results show that the optimal polymer has suitable features for further adsorption process. A series of static adsorption experiments were conducted to analyze its adsorption performance, which follows the Elovich model from the kinetic analysis and the Sips equation from the isothermal analysis. To further verify the reliability and accuracy of the simulation results, the effects of different monomers on the adsorption selectivity were also determined. They display higher selectivity towards phenol than 4‐nitrophenol.The results from the simulation of the pre‐assembled complexes are in reasonable agreement with those from the experiment.     

Superparamagnetic lysozyme surface-imprinted polymer prepared by atom transfer radical polymerization and its application for protein separation

Molecular imprinting as a promising and facile separation technique has received much attention because of their high selectivity for target molecules. In this study, the superparamagnetic lysozyme surface-imprinted polymer was prepared by a novel fabricating protocol, the grafting of the imprinted polymer on magnetic particles in aqueous media was done by atom transfer radical polymerization (ATRP), and the properties of the imprinted polymer were characterized in detail. Its high selective adsorption and recognition to lysozyme demonstrated the separation ability of the magnetic imprinted material to template molecule, and it has been used for quick and direct separation of lysozyme from the mixture of standard proteins and real egg white samples under an external magnetic field. Furthermore, the elution of lysozyme from the imprinted material was achieved by PEG/sulphate aqueous two-phase system, which caused lysozyme not only desorption from the imprinted materials but also redistribution in the top and bottom phase of aqueous two-phase system. The aqueous two-phase system exhibited some of the extraction and enrichment effect to desorbed lysozyme. Our results showed that ATRP is a promising method for the protein molecularly imprinted polymer preparation.     

Mathematical model using non-uniform flow distribution for dynamic protein breakthrough with membrane adsorption media

A mathematical model has been investigated to predict protein breakthrough during membrane adsorption/chromatography operations. The new model incorporates a non-uniform boundary condition at the column inlet to help describe the deviation from plug flow within real membrane adsorption devices. The model provides estimated breakthrough profiles of a binding protein while explicitly accounting for non-uniform flow at the inlet of the separation operation by modeling the flow distribution by a polynomial. We have explored experimental breakthrough curves produced using commercial membrane adsorption devices, as well as novel adsorption media of nanolayered nanofiber membranes, and compare them to model predictions. Further, the impact of using various simplifying assumptions is considered, which can have a dramatic effect on the accuracy and predictive ability of the proposed models. The new model, using only simple batch equilibrium and kinetic uptake rate data, along with membrane properties, is able to accurately predict the non-uniform and unsymmetrical shape for protein breakthrough during operation of membrane adsorption/chromatography devices.     

Successive SET‐LRP and ATRP synthesis of ferrocene‐based PPEGMEA‐g‐PAEFC well‐defined amphiphilic graft copolymer

A series of ferrocene‐based well‐defined amphiphilic graft copolymers, consisting of hydrophilic poly[poly(ethylene glycol) methyl ether acrylate] (PPEGMEA) backbone and hydrophobic poly(2‐acryloyloxyethyl ferrocenecarboxylate) (PAEFC) side chains were synthesized by successive single‐electron‐transfer living radical polymerization (SET‐LRP) and atom transfer radical polymerization (ATRP). The backbone was prepared by SET‐LRP of PEGMEA macromonomer, and it was then treated with lithium di‐isopropylamide and 2‐bromopropionyl bromide at ?78 °C to give PPEGMEA‐Br macroinitiator. The targeted well‐defined graft copolymers with narrow molecular weight distributions (M_w/M_n ≤ 1.32) were synthesized via ATRP of AEFC initiated by PPEGMEA‐Br macroinitiator, and the molecular weights of the backbone and side chains were both controllable. The electro‐chemical behaviors of graft copolymers were studied by cyclic voltammetry, and it was found that graft copolymers were more difficult to be oxidized, and the reversibility of electrode process became less with raising the content of PAEFC segment. The effects of the preparation method, the length of hydrophobic PAEFC segment, and the initial water content on self‐assembly behavior of PPEGMEA‐g‐PAEFC graft copolymers in aqueous media were investigated by transmission electron microscopy. The morphologies of micelles could transform from cylinders to spheres or rods with changing the preparation condition and the length of side chains. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

The role of ligands on protein retention in adsorption chromatography: A surface energetics approach

Protein adsorption onto hydrophobic chromatographic supports has been investigated using a colloid theory surface energetics approach. The surface properties of commercially available chromatographic beads, Toyopearl Phenyl 650‐C, and Toyopearl Butyl 650‐C, have been experimentally determined by contact angle and zeta potential measurements. The adsorption characteristics of these beads, which bear the same backbone matrix but harbor different ligands, have been studied toward selected model proteins, in the hydrated as well as dehydrated state. There were two prominent groups of proteins observed with respect to the chromatographic supports presented in this work: loosely retained proteins, which were expected to have lower average interaction energies, and the strongly retained proteins, which were expected to have higher average interaction energies. Results were also compared and contrasted with calculations derived from adsorbent surface energies determined by inverse liquid chromatography. These results showed a good qualitative agreement, and the interaction energy minima obtained from these extended Derjaguin, Landau, Verwey and Overbeek calculations were shown to correlate well with the experimentally determined adsorption behavior of each protein.     

Block copolymer mediated synthesis of amphiphilic gold nanoparticles in water and an aqueous tetrahydrofuran medium: An approach for the preparation of polymer–gold nanocomposites

The synthesis of polymer‐matrix‐compatible amphiphilic gold (Au) nanoparticles with well‐defined triblock polymer poly[2‐(N,N‐dimethylamino)ethyl methacrylate]‐b‐poly(methyl methacrylate)‐b‐poly[2‐(N,N‐dimethylamino)ethyl methacrylate] and diblock polymers poly(methyl methacrylate)‐b‐poly[2‐(N,N‐dimethylamino)ethyl methacrylate], polystyrene‐b‐poly[2‐(N,N‐dimethylamino)ethyl methacrylate], and poly(t‐butyl methacrylate)‐b‐poly[2‐(N,N‐dimethylamino)ethyl methacrylate] in water and in aqueous tetrahydrofuran (tetrahydrofuran/H₂O = 20:1 v/v) at room temperature is reported. All these amphiphilic block copolymers were synthesized with atom transfer radical polymerization. The variations of the position of the plasmon resonance band and the core diameter of such block copolymer functionalized Au particles with the variation of the surface functionality, solvent, and molecular weight of the hydrophobic and hydrophilic parts of the block copolymers were systematically studied. Different types of polymer–Au nanocomposite films [poly(methyl methacrylate)–Au, poly(t‐butyl methacrylate)–Au, polystyrene–Au, poly(vinyl alcohol)–Au, and poly(vinyl pyrrolidone)–Au] were prepared through the blending of appropriate functionalized Au nanoparticles with the respective polymer matrices {e.g., blending poly[2‐(N,N‐dimethylamino)ethyl methacrylate]‐b‐poly(methyl methacrylate)‐b‐poly[2‐(N,N‐dimethylamino)ethyl methacrylate‐stabilized Au with the poly(methyl methacrylate)matrix only}. The compatibility of specific block copolymer modified Au nanoparticles with a specific homopolymer matrix was determined by a combination of ultraviolet–visible spectroscopy, transmission electron microscopy, and differential scanning calorimetry analyses. The facile formation of polymer–Au nanocomposites with a specific block copolymer stabilized Au particle was attributed to the good compatibility of block copolymer coated Au particles with a specific polymer matrix. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1841–1854, 2006     

Synthesis of amphiphilic graft copolymer brush and its use as template film for the preparation of silver nanoparticles

A microphase‐separated, amphiphilic graft copolymer consisting of a poly (vinyl chloride) (PVC) backbone and poly(oxyethylene methacrylate) (POEM) side chains, (PVC‐g‐POEM at 62:38 wt %) was synthesized via atom transfer radical polymerization (ATRP). Nuclear magnetic resonance (¹H NMR), FTIR spectroscopy, and transmission electron microscopy (TEM) clearly revealed that the “grafting from” method using ATRP was successful and that the graft copolymer molecularly self‐assembled into discrete nanophase domains of continuous PVC and isolated POEM regions. The self‐assembled graft copolymer film was used to template the growth of silver nanoparticles in solid state by introducing a AgCF₃SO₃ precursor and a UV irradiation process. The in situ formation of silver nanoparticles in the graft copolymer template film was confirmed by TEM, UV–visible spectroscopy, and wide angle X‐ray scattering. FTIR spectroscopy and X‐ray photoelectron spectroscopy also demonstrated the selective incorporation and in situ formation of silver nanoparticles within the hydrophilic POEM domains, presumably due to strong interactions between the silver and the ether oxygen in POEM. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3911–3918, 2008     

Atom transfer radical polymerization of 2-methoxy ethyl acrylate and its block copolymerization with acrylonitrile

2-Methoxy ethyl acrylate (MEA), a functional monomer was homopolymerized using atom transfer radical polymerization (ATRP) technique with methyl 2-bromopropionate (MBP) as initiator and CuBr/N,N,N′,N′,N″-pentamethyldiethylenetriamine (PMDETA) as catalyst system; polymerization was conducted in bulk at 60 °C and livingness was established by chain extension reaction. The kinetics as well as molecular weight distribution data indicated towards the controlled nature of polymerization. The initiator efficiency and the effect of initiator concentration on the rate of polymerization were investigated. The polymerization remained well-controlled even at low catalyst concentration of 10% relative to initiator. The influence of different solvents, viz. ethylene carbonate and toluene on the polymerization was investigated. End-group analysis for the determination of high degree of functionality of PMEA was determined with the help of ¹³C{¹H} NMR spectra. Chain extension experiment was conducted with PMEA macroinitiator for ATRP of acrylonitrile (AN) in ethylene carbonate at 70 °C using CuCl/bpy as catalyst system. The composition of individual blocks in PMEA-b-PAN copolymers was determined using ¹H NMR spectra.     

SET‐LRP synthesis of PMHDO‐g‐PNIPAM well‐defined amphiphilic graft copolymer

A well‐defined amphiphilic graft copolymer, consisting of hydrophobic polyallene‐based backbone and hydrophilic poly(N‐isopropylacrylamide) (PNIPAM) side chains, was prepared by the combination of living coordination polymerization, single electron transfer‐living radical polymerization (SET‐LRP), and the grafting‐from strategy. First, the double‐bond‐containing backbone was prepared by [(η³‐allyl)NiOCOCF₃]₂‐initiated living coordination polymerization of 6‐methyl‐1,2‐heptadiene‐4‐ol (MHDO). Next, the pendant hydroxyls in every repeating unit of poly(6‐methyl‐1,2‐heptadiene‐4‐ol) (PMHDO) homopolymer were treated with 2‐chloropropionyl chloride to give PMHDO‐Cl macroinitiator. Finally, PNIPAM side chains were grown from PMHDO backbone via SET‐LRP of N‐isopropylacrylamide initiated by PMHDO‐Cl macroinitiator in N,N‐dimethylformamide/2‐propanol using copper(I) chloride/tris(2‐(dimethylamino)ethyl)amine as catalytic system to afford PMHDO‐g‐PNIPAM graft copolymers with a narrow molecular weight distribution (M_w/M_n = 1.19). The critical micelle concentration (cmc) in water was determined by fluorescence probe technique and the effects of pH and salinity on the cmc of PMHDO‐g‐PNIPAM were also investigated. The micellar morphology was found to be spheres using transmission electron microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

PNIPAM‐b‐(PEA‐g‐PDMAEA) double‐hydrophilic graft copolymer: Synthesis and its application for preparation of gold nanoparticles in aqueous media

A series of well‐defined double‐hydrophilic graft copolymers, consisting of poly(N‐isopropylacrylamide)‐b‐poly(ethyl acrylate) (PNIPAM‐b‐PEA) backbone and poly(2‐(dimethylamino)ethyl acrylate) (PDMAEA) side chains, were synthesized by the combination of single‐electron‐transfer living radical polymerization (SET‐LRP) and atom‐transfer radical polymerization (ATRP). PNIPAM‐b‐PEA backbone was first prepared by sequential SET‐LRP of N‐isopropylacrylamide and 2‐hydroxyethyl acrylate at 25 °C using CuCl/tris(2‐(dimethylamino)ethyl)amine as catalytic system followed by the transformation into the macroinitiator by treating the pendant hydroxyls with 2‐chloropropionyl chloride. The final graft copolymers with narrow molecular weight distributions were synthesized by ATRP of 2‐(dimethylamino)ethyl acrylate initiated by the macroinitiator at 40 °C using CuCl/tris(2‐(dimethylamino)ethyl)amine as catalytic system via the grafting‐from strategy. These copolymers were employed to prepare stable colloidal gold nanoparticles with controlled size in aqueous solution without any external reducing agent. The morphology and size of the nanoparticles were affected by the length of PDMAEA side chains, pH value, and the feed ratio of the graft copolymer to HAuCl₄. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1811–1824, 2009     

Preparation and characterization of graft terpolymers with controlled molecular structure

Segmented terpolymers, poly(alkyl methacrylate)‐g‐poly(D ‐lactide)/poly(dimethylsiloxane) (PLA/PDMS), were prepared with a combination of the “grafting through” technique (macromonomer method) and controlled/living radical polymerization (atom transfer radical polymerization or reversible addition–fragmentation transfer polymerization). Two synthetic pathways were used. The first was a single‐step approach in which a low‐molecular‐weight methacrylate monomer (methyl methacrylate or butyl methacrylate) was copolymerized with a PLA macromonomer and a PDMS macromonomer. The second strategy was a two‐step approach in which a graft copolymer containing one macromonomer was chain‐extended by a copolymerization of the second macromonomer and the low‐molecular‐weight methacrylate. The kinetics of both synthetic approaches were investigated, showing that the polymerizations exhibited a controlled/living behavior. Furthermore, the molecular structure of the terpolymers (composition, molecular weight distribution, and microstructure) was investigated by two‐dimensional liquid chromatography. Well‐defined terpolymers with controlled branch distribution, composition (F_w,PMMA/F_w,PLA/F_w,PDMS ～ 50/30/20) molecular weight (M_n ～ 50,000 g · mol^?1), and a narrow molecular weight distribution (M_w/M_n ～ 1.3) were prepared via both pathways. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1939–1952, 2004     

Fabrication of molecularly imprinted resin via controlled polymerization applied in the enrichment of bisphenol A for plastic products

The addition of bisphenol A has been frequently used in industrial manufacturing because it imparts plastic products with characteristics such as transparency, durability, and excellent impact resistance. However, its widespread use raises concerns about potential leakage into the surrounding environment, which poses a significant risk to human health. In this study, molecularly imprinted polymers with specific recognition of bisphenol A were synthesized through surface-initiated atom transfer radical polymerization using poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) as the substrate, bisphenol A as the template molecule, 4-vinylpyridine as the monomer, and ethylene glycol dimethacrylate as the cross-linker. The bisphenol A adsorption capacity was experimentally investigated, and the kinetic analysis of the molecularly imprinted polymers produced an adsorption equilibrium time of 25 min, which is consistent with the pseudo-second-order kinetic model. The results of the static adsorption experiments exhibited consistency with the Langmuir adsorption model, revealing a maximum adsorption capacity of 387.2 μmol/g. The analysis of molecularly imprinted polymers-enriched actual samples using high-performance liquid chromatography demonstrated excellent selectivity for bisphenol A, with a linear range showing 93.4%–99.7% recovery and 1.1%–6.4% relative standard deviation, demonstrating its high potential for practical bisphenol A detection and enrichment applications.     

Preparation of a novel polymer monolith with functional polymer brushes by two‐step atom‐transfer radical polymerization for trypsin immobilization

Novel porous polymer monoliths grafted with poly{oligo[(ethylene glycol) methacrylate]‐co‐glycidyl methacrylate} brushes were fabricated via two‐step atom‐transfer radical polymerization and used as a trypsin‐based reactor in a continuous flow system. This is the first time that atom‐transfer radical polymerization technique was utilized to design and construct polymer monolith bioreactor. The prepared monoliths possessed excellent permeability, providing fast mass transfer for enzymatic reaction. More importantly, surface properties, which were modulated via surface‐initiated atom‐transfer radical polymerization, were found to have a great effect on bioreactor activities based on Michaelis–Menten studies. Furthermore, three model proteins were digested by the monolith bioreactor to a larger degree within dramatically reduced time (50 s), about 900 times faster than that by free trypsin (12 h). The proposed method provided a platform to prepare porous monoliths with desired surface properties for immobilizing various enzymes.     

Composite Nafion membrane embedded with hybrid nanofillers for promoting direct methanol fuel cell performance

A special type of hybrid nano-particles was incorporated into the Nafion^® matrix to form a composite membrane. These nano-particles possessed a core–shell structure consisting of silica core (<10 nm) and a densely grafted oligomeric ionmer layer, which was synthesized via atom transfer radical polymerization (ATRP) on the particles’ surface. Besides considerable improvement in the proton conductivity of the membrane, the presence of these hybrid nano-particles in the Nafion^® matrix also repressed its methanol permeability by almost four times. The composite membrane also demonstrated superior performance when tested in a single cell membrane-electrolyte assembly (MEA) under direct methanol fuel cell (DMFC) operating condition. It was found that the composite membrane enabled a power density output that was 1.5 times greater than that of pristine Nafion^®.