Monolithic capillary columns synthesized from a single phosphate-containing dimethacrylate monomer for cation-exchange chromatography of peptides and proteins

Monoliths containing phosphoric acid functional groups were synthesized from only one monomer, bis[2-(methacryloyloxy)ethyl] phosphate (BMEP), in 75-μm i.d. UV transparent fused-silica capillaries by photo-initiated polymerization for cation exchange chromatography of peptides and proteins. Various synthetic conditions, including porogen solvents, monomer concentration, and polymerization time, were studied. The hydrophobicities of the resulting monoliths were evaluated using propyl paraben under reversed-phase conditions and synthetic peptides under ion-exchange conditions. These monoliths exhibited low hydrophobicities and relatively low porosities due to their highly cross-linked structures. A dynamic binding capacity (lysozyme) of 73 mg/mL of column volume was measured using the best performing monolith. Synthetic peptides were eluted in approximately 30 min without addition of acetonitrile to the mobile phase, yielding a peak capacity of 28. Efficiencies of 52,900 plates/m for peptides and 71,000 plates/m for proteins were obtained under isocratic conditions. The effects of separation conditions, i.e., mobile phase pH and salt gradient rate, were studied. Good run-to-run reproducibility was achieved with a relative standard deviation (RSD) less than 1.5% for retention times of proteins. The column-to-column retention time reproducibility for peptides was less than 3.5% RSD. A monolithic column was used to follow the deamidation of ribonuclease A. The kinetics of deamidation were founded to be first order with a half life of 195 h. A cytochrome C digest was also separated using a linear gradient of sodium chloride.     

Column packing for gas chromatography containing immobilized poly(ethylene glycol) stationary phase

Summary Carbowax 20M poly(ethylene glycol) stationary phase was immobilized on Chromosorb W by cross-linking with pluriisocyanate. The properties of the prepared packing material were investigated. Column efficiencies of 10,960 and 7,510 theoretical plates/meter were obtained for n-pentadecane and 1-heptanol, respectively.     

Preparation of poly(N-isopropylacrylamide)-grafted polymer monolith for hydrophobic interaction chromatography of proteins

Poly(N-isopropylacrylamide)-grafted polymer monolith has been achieved using a surface-initiated atom transfer radical polymerization grafting polymerization within the pores of poly(chloromethylstyrene-divinylbenzene) macroporous monolith contained in a 100 mm × 4.6 mm I.D. stainless steel column. The grafted-poly(N-isopropylacrylamide) on the surface of the grafted monolith that was used as chromatographic stationary phase showed a response to the variation of temperatures and/or salt concentrations. This study focus on its salt concentration responsive property and it has been revealed that the hydrophobicity of the grafted monolith can be adjusted by changing salt concentrations in the range of 0.05-2.0 mol/L. A variety of salts including sodium sulfate, ammonium sulfate and sodium chloride exhibited different effects on the alteration of hydrophobicity of the grafted monolith, and the effect of the salts was in the order of sodium sulfate > ammonium sulfate > sodium chloride. Based on this response to salt concentrations, the grafted monolith was applied in hydrophobic interaction chromatography of proteins, and the base-line separation of a six proteins mixture consisting of cytochrome c, myoglobin, ribonuclease A, bovine serum albumin, ovalbumin and thyroglobulin bovine was achieved by a salt gradient elution.     

Methoxy poly(ethylene glycol)-b-poly(valerolactone) diblock polymeric micelles for enhanced encapsulation and protection of camptothecin

Amphiphilic block copolymers, methoxy poly(ethylene glycol)-b-poly(valerolactone) (mPEG-b-PVL), were synthesized via ring opening polymerization of δ-valerolactone in the presence of methoxy poly(ethylene glycol) (mPEG). The copolymers form micelle-like nanoparticles by their amphiphilic characteristics and their structures were examined by Nuclear Magnetic Resonance (NMR). The sizes of nanoparticles ranged from 60 to 120 nm as measured by dynamic light scattering detection, and were larger with higher molecular weight of the copolymers. The Critical Micelle Concentration (CMC) of these nanoparticles in water decreased with increasing molecular weight of hydrophobic segment. Stability analysis showed that the micellar solutions maintain their sizes at 37 °C for six weeks without aggregation or dissociation. The lyophilization method was better than the evaporation method when camptothecin (CPT) was incorporated to the micelles. The former method yielded higher CPT loading efficiency and lower aggregation. The loading efficiency of CPT could be more than 96% and a steady release rate of CPT was kept for twenty six days. Moreover, the mPEG-b-PVL polymeric micelles offered good protection of CPT lactone form at 37 °C for sixteen days. The copolymers showed no cytotoxicity towards L929 mouse muscular cells when incubated for one day. Taken together, the mPEG-b-PVL copolymer has potential to be used for the delivery of CPT or other similar drugs.     

Determination of poly(ethylene glycol)s by both normal-phase and reversed-phase modes of high-performance liquid chromatography

A normal-phase HPLC system using an amino column has been developed to characterise oligomers of poly(ethylene glycol)s (PEGs) of average M_r 400 to 2000 with derivatisation by dinitrobenzoate. Normal-phase HPLC with gradient elution using ternary solvents of hexane, dichloromethane and methanol has produced a baseline resolution for oligomers of PEG 400, 600 and 1000, while PEG 1000 and 2000 were analysed by using binary solvents of acetonitrile and water. Mixtures of PEGs have been determined by these HPLC systems. PEG 400 in a textile finish has also been determined with satisfactory recovery. It has been found that the hydroxyl group of solvents in normal-phase HPLC plays an important role in resolution and retention of PEG oligomers. Derivatisation efficiency for PEGs by dinitrobenzoyl chloride and quantitative determination of derivatised PEGs by HPLC have been studied. A reversed-phase (RP) mode of HPLC was examined for determination of PEG 400 oligomers. The normal-phase system provided greater resolution for oligomers of PEGs.     

New architectures of poly(ethylene glycol) and poly(methylthiirane) in block copolymers

Two synthetic ways were experimented to prepare new architectures of block copolymers made of poly(ethylene glycol) (PEG) and poly(methylthiirane). The coupling of both blocks conveniently end-capped as well as anionic polymerization of methylthiirane initiated by PEG-thiols gave readily the copolymers. Their characterization by ¹H NMR, SEC and IR confirmed the expected structures.     

Crystallization of photo-chain extended poly(ethylene glycol)

Coumarin-functionalized poly(ethylene glycol) (PEG) monols and diols were isothermally crystallized at temperatures between 20 and 35 °C before and after exposure to approximately 110 J cm⁻² of ultra-violet A (λ > 300 nm, UVA) irradiation. Irradiation dimerized the coumarin groups and chain-extended the coumarin-functionalized PEG oligomers. The higher molecular weights reduced the crystal growth rate by as much as 50% compared to the non-irradiated coumarin-functionalized PEG oligomers under ambient crystallization conditions. Hoffman’s kinetic nucleation theory was utilized to evaluate the types of nucleation that occurred for the coumarin-functionalized PEG diols (COU-PEG-COU). Crystallization regimes II and III were observed for the coumarin-modified PEG oligomers before and after exposure to UVA light.     

Determination of poly(ethylene glycol) 300 in long chain free fatty acid mixtures by reversed-phase high-performance liquid chromatography

A rapid sensitive method has been developed for the detection and quantitation of poly(ethylene glycol) 300 (PEG 300) in long-chain free fatty acid mixtures that requires minimal sample preparation. The PEG 300 was separated from the free fatty acids by RP-HPLC using a water–tetrahydrofuran gradient. PEG and the free fatty acids were detected using evaporative light scattering detection. The minimum detectable level of PEG in a free fatty acid mixture was 0.0125%.     

A very thin coating for capillary zone electrophoresis of proteins based on a tri(ethylene glycol)-terminated alkyltrichlorosilane

We describe the use of a tri(ethylene glycol)-terminated alkyltrichlorosilane to create a very thin, protein-resistant "self-assembled monolayer" coating on the inner surface of a fused-silica capillary. The same compound has been demonstrated previously on flat silica substrates to resist adsorption of many proteins. As a covalently bound capillary coating, it displays good resistance to the adsorption of cationic proteins, providing clean separations of a mixture of lysozyme, cytochrome c, ribonuclease A, and myoglobin for more than 200 consecutive runs. Electroosmotic flow (EOF) was measured as a function of pH; the coated capillary retains significant cathodal EOF, with roughly 50% of the EOF of an uncoated capillary at neutral pH, making this coating promising for applications requiring some EOF. The EOF was reasonably stable, with a 2.9% relative standard deviation during a 24 h period consisting of 72 consecutive separations of cationic proteins. Efficiencies for cationic protein separations were moderate, in the range of 190,000-290,000 theoretical plates per meter. The coating procedure was simple, requiring only a standard cleaning procedure followed by a rinse with the silane reagent at room temperature. No buffer additives are required to maintain the stability of the coating, making it flexible for a range of applications, potentially including capillary electrophoresis-mass spectrometry (CE-MS).     

An analysis of the complexation between poly(aspartic acid) and poly(ethylene glycol)

The compatibility between poly(aspartic acid) and poly(ethylene glycol) for the formation of an interpolymer complex (IPC) was investigated by dynamic rheology and evaluation of zeta potential values. The homogeneity of the realized IPC was observed by near infrared chemical imagistic (NIR-CI) technique. The data were sustained and underlined by the assessment of the compatibility between the polymeric compounds.     

Poly (methacrylic acid-ethylene glycol dimethacrylate) monolithic capillary for in-tube solid phase microextraction coupled to high performance liquid chromatography and its application to determination of basic drugs in human serum

A poly (methacrylic acid-ethylene glycol dimethacrylate) monolithic capillary column was prepared for in-tube solid-phase microextraction. Comparing with the commonly used open tubular extraction capillary, which cannot provide sufficient extraction efficiency since the ratio of its coating volume to that of the capillary void volume is relatively small, the monolithic column with greater phase ratio combined with convective mass transfer provides the possibility to improve the extraction efficiency with shorter capillary. As to poly (methacrylic acid-ethylene glycol dimethacrylate), its hydrophobic main chains and acidic pendant groups make it a superior material for extraction of basic analytes from aqueous matrix.An on-line monolithic capillary column solid phase microextraction (SPME) method was developed for determination of theobromine, theophylline and caffeine in serum samples. The high extraction efficiency was obtained for all the three analytes, yielding the detection limits of 12, 8 and 6.5 ng/mL by UV detection, respectively. Excellent method reproducibility (R.S.D. < 2.9%) was found over a linear dynamic range of 0.05-2 μg/mL in serum sample. The monolithic capillary column was proved to be reusable in coping with serum samples, which would facilitate practical determination of basic drugs.     

Polymer-based monolithic microcolumns for hydrophobic interaction chromatography of proteins

Monolithic capillary columns for hydrophobic interaction chromatography (HIC) have been prepared by thermally initiated, single-step in situ polymerization of mixtures of monovinyl monomers including butyl methacrylate and/or 2-hydroxyethyl methacrylate, with a divinyl crosslinker glycerol dimethacrylate or 1,4-butanediol dimethacrylate using two different porogen systems. Two porogenic solvent mixtures were used; one "hydrophilic", consisting of water, butanediol, and propanol, and one "hydrophobic," comprising dodecanol and cyclohexanol. The porous structures of the monoliths were characterized and their performance was demonstrated with a separation of a mixture of myoglobin, ribonuclease A, and lysozyme under conditions typical of HIC.     

Cationic poly(amidoamine) dendrimers as additives for capillary electroseparation and detection of proteins

We examine the influence of cationic poly(amidoamine) (PAMAM) dendrimers on capillary electroseparation–UV analysis of proteins. PAMAMs adsorbing to the capillary surface suppressed the wall‐adsorption of proteins; meanwhile, PAMAMs added to the buffer exhibited selectivity toward proteins. Presence of 3×10^?4 g/mL PAMAM generation one (G 1.0) in 30 mM phosphate, at pH 2.6, rendered significant enhancement in separation efficiency; the merged peaks of myoglobin and trypsin inhibitor were separated. Moreover, the protein–dendrimer interactions changed the inherent UV absorbance profiles of proteins. UV–Vis study showed that the absorbance of cytochrome C and transferrin increased at the detection wavelength of 214 nm; their detection sensitivity enhanced by 2.44 and 2.01‐folds, respectively, with addition of 5×10^?4 g/mL PAMAM G 1.0.     

Synthesis and properties of polymer brushes composed of poly(diphenylacetylene) main chain and poly(ethylene glycol) side chains

Novel cylindrical polymer brushes consisting of poly(diphenylacetylene) main chain and poly(poly(ethylene glycol) methyl ether monomethacrylate) (PPEGMA) side chains were synthesized by the diphenylacetylene macromonomer or side chain initiated atom transfer radical polymerization (ATRP) of poly(ethylene glycol) methyl ether monomethacrylate (PEGMA) from an bromo isobutyryl-bearing poly(diphenylacetylene) (poly(BrDPA)) method. The diphenylacetylene macromonomer, namely, DPA-PPEGMA, were prepared by the ATRP of PEGMA from bromo isobutyryl-bearing diphenylacetylene. DPA-PPEGMA was polymerized successfully with WCl₆-Ph₄Sn catalyst to give high molecular weight polymer brushes poly(DPA-PPEGMA). Meanwhile, polymer brushes (PDPA-g-PPEGMA) were obtained by ATRP of PEGMA from poly(BrDPA). The molecular weight of the side chains of PPEGMA could be controlled simply by modulating the ATRP time. The macromonomer and polymer brushes are soluble in nonpolar solvents such as toluene and chloroform. The polymers of poly(BrDPA) and poly(DPA-PPEGMA) absorb in the longer wavelength region, with two peaks at around 370 and 414 nm. The polymers are thermally stable and exhibit double crystallization and melting peaks during the cooling and heating scans.     

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide),PEG-b-(PNIPAM)_2,were successfully synthesized through atom transfer radical polymerization(ATRP).A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether(PEG).The copolymers were obtained via the ATRP of N-isopropylacrylamide(NIPAM) at 30℃with CuCl/Me_6TREN as a catalyst system and DMF/H_2O(v/v = 3:1) mixture as solvent.The resulting copo...     

Suspension polymerization of poly(ethylene glycol) methacrylate: a route for swellable spherical gel beads with controlled hydrophilicity and functionality

 Spherical and swellable gel beads were obtained by the suspension polymerization of poly(ethylene glycol) methacrylate macromonomer (PEG-MA). The average size and size distribution properties, the equilibrium swelling behaviour and the protein adsorption characteristics of PEG-MA-based gel beads were determined. In the suspension polymerization system, the organic phase including monomer, cross-linker and diluent solution was dispersed in an aqueous medium by using poly(vinylpyrrolidone) as the stabilizer. The diluent solution was prepared by mixing cyclohexanol and octanol at different volume ratios. The suspension polymerization experiments were designed in two separate parts. In the first part, ethylene glycol dimethacrylate was selected as the cross-linker and swellable PEG-MA-based gel beads were obtained by changing the cross-linker concentration, the monomer/diluent ratio and the stirring rate. In the second part, a more hydrophobic structure, divinylbenzene (DVB) was tried as a cross-linker. In this part, PEG-MA-DVB copolymer beads were obtained by changing the DVB/PEG-MA feed ratio. Then, the hydrophicility of the resulting gel beads could be controlled by changing the feed ratio of hydrophilic macromonomer to hydrophobic cross-linker. This property was also used to control the extent of nonspecific protein adsorption onto the surface of the gel beads. The non specific albumin adsorption onto the gel beads decreased with increasing PEG-MA content. No significant nonspecific adsorption at the isoelectric point of albumin was detected onto the gel beads produced with the higher PEG-MA/DVB feed ratios. For specific albumin adsorption, a triazinyl dye (i.e., cibacron blue, CB F3G-A) was covalently attached onto the surface of the copolymer beads via terminal hydroxyl groups of PEG-MA. The results of albumin adsorption experiments with the CB F3G-A carrying beads indicated that an appreciable specific albumin adsorption capacity could be obtained with the gel beads produced with a PEG-MA/DVB feed ratio of 1.5/4.0. Received: 16 August 1999/Revised: 27 December 1999     

Application of poly(methacrylic acid-ethylene glycol dimethacrylate) monolith microextraction coupled with capillary zone electrophoresis to the determination of opiates in human urine

A novel poly(methacrylic acid-ethylene glycol dimethacrylate) (MAA-EGDMA) monolith microextraction method coupled with CZE was proposed for rapidly determining a mixture of opiates comprising heroin, 6-monoacetylmorphine, morphine, codeine, papaverine, and narcotine in human urine. The extraction device contained a regular plastic syringe, the poly(MAA-EGDMA) monolithic capillary tube (530 microm id x 3 cm) and a plastic pinhead, which connected the monolithic capillary tube and the syringe without leakage. In the polymer monolith microextraction, the sample solution was ejected via the monolithic capillary tube by a programmable syringe pump, followed by desorption with an aliquot of appropriate solution, which was collected into a vial for the subsequent analysis by CZE. The best separation was achieved using a buffer composed of 0.1 M disodium hydrogen phosphate (adjusted to pH 4.5 with 1 M hydrochloric acid) and 20% methanol v/v with temperature and voltage of 25 degrees C and 25 kV, respectively. By applying electrokinetic injection with field-enhanced sample stacking, detection limits of 6.6-19.5 ng/mL were achieved. Excellent method of reproducibility was found over a linear range of 80-2000 ng/mL.     

Crystallization behavior and biodegradation of poly(3-hydroxybutyrate) and poly(ethylene glycol) multiblock copolymers

Block copolymerization by using isocyanates is an effective method for incorporating PHB and PEG because it can prepare copolymers with good properties, such as toughness, strength, and so on. In this study, we adopted soil suspension system to estimate the biodegradability of a series of PHB/PEG multiblock copolymers with different compositions and block lengths. In the degradation process, the changes in weight loss, molecular weight, and tensile strength were periodically measured to determine the biodegradability, and the surface morphology was also observed by SEM. In contrast to pure PHB, the weight loss of the copolymer was relatively lower. On the other hand, the tensile strength and molecular weight experienced apparent decrease, and for BHG1000-3-1, they reached 46.7% and 77.7% of the initial value, respectively. SEM observation showed that the surface was covered with numerous erosion pits. All these indicate that the degradation indeed took place and long-chain molecules have been hydrolyzed into shorter ones. The crystallization behavior was also investigated by DSC and WAXD. The results showed that both the segments, PEG and PHB, can form crystalline phases at lower PHB contents ranging from 29% to 44%, and when PHB component was more than 60%, only PHB phase can crystallize.     

聚二甲基丙烯酸乙二醇酯壁材微胶囊的制备及其表征

采用界面自由基聚合的方法,制备了以聚二甲基丙烯酸乙二醇酯(PEGDMA)为壁材,薄荷素油(DPO)与石蜡或者三辛癸酸甘油酯(GTCC)的混合物为芯材的微胶囊.微胶囊壁材是二甲基丙烯酸乙二醇酯(EGDMA)单体通过界面自由基聚合形成的高聚物PEGDMA.提出了该界面自由基聚合形成PEGDMA的机理过程.利用光学显微镜和扫描电镜探究了乳化剂类型、芯材组成和固化温度对微胶囊形貌的影响.用傅里叶红外光谱对微胶囊的化学结构进行了表征.利用紫外分光光度计测出了未被微胶囊包埋的芯材占总芯材的百分比(free oil).并用热重分析仪分析了微胶囊的热稳定性能,讨论了固化时间对微胶囊热性能的影响.结果表明,采用阿拉伯树胶为乳化剂,芯材组成为质量比M_(DPO)/M_(GTCC)=1∶1,在60℃下固化1 h,制备出的微胶囊为饱满的球形状,表面光滑.同时测得该体系中芯材的free oil为26.5 wt%.PEGDMA微胶囊在60℃固化温度下反应3 h,具有很好热稳定性,且固化温度升高能提高微胶囊的热稳定性.所制备的微胶囊无毒,在个人护理品和医药领域具有广泛的应用前景.     

Formation of nanoporous poly(aryl amide ether) (PAAE) films by selective removal of poly(ethylene glycol) (PEG) from PEG/PAAE composite films

Poly(aryl amide ether) (PAAE) thin films with nanometer-sized pores have been prepared in two steps: (1) solution casting of partially miscible poly(ethylene glycol) (PEG)/PAAE blends from one of their common solvents, dimethyl sulfoxide (DMSO), results in formation of PEG/PAAE nanocomposite films; (2) selective removal of PEG component by water washing yields nanosized, porous PAAE films. The pores have been found to have a small size variation and cover the whole surface homogeneously. With an increase in PEG contents, the sizes of the pores increase but the size distributions do not have much changes. This has been ascribed to formation of small PEG domains in PEG/PAAE composite films, which is facilitated by the strong interactions, mostly hydrogen bonds, between PEG and PAAE macromolecular chains.