Synthesis and characterisation of molecularly imprinted catalytic microgels for carbonate hydrolysis

Novel molecularly imprinted microgels incorporating arginine and tyrosine side chains as functional monomers have been designed and synthesised with percentages of cross-linker ranging from 70 to 90%. Full chemico-physical characterisation including M_r, coil density and size particle determination concluded that all polymer preparations obtained can be classified as microgels. Molecular imprinting using a phosphate template was used to generate catalytic microgels for the hydrolysis of p-nitrophenyl carbonates. Kinetic characterisation of the catalytic activity of the different preparations indicated that values of critical monomer concentration (C_M) and percentage of cross-linker play an important role in determining the catalytic efficiency of the different preparations. Microgels containing 70% cross-linker were the only ones following the Michaelis-Menten saturation model and kinetic parameters were obtained using 4 mg/ml of M397: V_max = 1.34 × 10⁻⁶ M s⁻¹ (S.E. 1.28 × 10⁻⁷) and K_M = 2.38 × 10⁻³ M (S.E. 3.1 × 10⁻⁴).     

Structural and dynamical properties of aqueous mixtures of pectin and chitosan

In this study phase separation, structure, and dynamics of aqueous pectin-chitosan mixtures of different ratios and a pure aqueous pectin sample have been investigated under various conditions by turbidimetry, SANS and dynamic light scattering (DLS). Only the mixture with r = 0.75 gelled upon decreasing the temperature ((r ≡ m_pectin/(m_pectin + m_chitosan), where m denotes the mass of the considered component). The pure pectin sample (r = 1) did not gel and the decrease in temperature seemed to promote phase separation. The addition of chitosan reduced the tendency of pectin to phase separate in the mixtures of pectin and chitosan. The general trend when cooling the samples was that the turbidity and the growth of the turbidity became more pronounced as the amount of pectin in the mixture was increased. The wavelength dependence of the turbidity indicated a change of the conformation of pectin chains from an extended form to a more compact structure in pectin solutions without chitosan as the temperature decreased. This was not observed for the mixture of pectin and chitosan. SANS measurements revealed excess scattered intensity in the low wave vector area with the strongest upturn for the pure pectin sample (r = 1). DLS experiments showed longer slow relaxation times after a temperature quench for all samples, with the most pronounced effect for the mixture of pectin and chitosan with r = 0.75. The synergism between pectin and chitosan at high pectin contents (r = 0.75) generated large association complexes over time.     

Homopolymer and copolymers of 4-nitro-3-methylphenyl methacrylate with glycidyl methacrylate: Synthesis, characterization, monomer reactivity ratios and thermal properties

The novel methacrylic monomer, 4-nitro-3-methylphenyl methacrylate (NMPM) was synthesized by reacting 4-nitro-3-methylphenol dissolved in ethyl methyl ketone (EMK) with methacryloyl chloride in the presence of triethylamine as a catalyst. The homopolymer and copolymers of NMPM with glycidyl methacrylate having different compositions were synthesized by free radical polymerization in EMK solution at 70 ± 1 °C using benzoyl peroxide as free radical initiator. The homopolymer and the copolymers were characterized by FT-IR, ¹H NMR and ¹³C NMR spectroscopic techniques. The solubility tests were tested in various polar and non-polar solvents. The molecular weight and polydispersity indices of the copolymers were determined using gel permeation chromatography. The glass transition temperature of the copolymers increases with increase in NMPM content. The thermogravimetric analysis of the polymers performed in air showed that the thermal stability of the copolymer increases with NMPM content. The copolymer composition was determined using ¹H NMR spectra. The monomer reactivity ratios were determined by the application of conventional linearization methods such Fineman-Ross (r₁ = 1.862, r₂ = 0.881), Kelen-Tudos (r₁ = 1.712, r₂ = 0.893) and extended Kelen-Tudos methods (r₁ = 1.889, r₂ = 0.884).     

Studies on photocrosslinkable copolymers of 4-methacryloyloxyphenyl-3′,4′-dimethoxystyryl ketone and methyl methacrylate

Copolymers with various contents of 4-methacryloyloxyphenyl-3′,4′-dimethoxystyryl ketone (MPDSK) and methyl methacrylate (MMA) were prepared in methyl ethyl ketone solution using benzoyl peroxide as a free radical initiator at 70 °C. Characterization of the resulting polymers was done by UV, FT-IR, ¹H NMR and ¹³C NMR spectroscopic techniques. The copolymer compositions were determined by ¹H NMR analysis. The monomer reactivity ratios were calculated using linearisation methods such as Finemann-Ross (r₁ = 0.4283 and r₂ = 0.3050), Kelen-Tudos (r₁ = 0.4264 and r₂ = 0.2606), and extended Kelen-Tudos (r₁ = 0.4022 and r₂ = 0.2704) methods as well as by a non-linear error-in-variables model (EVM) method using the computer program RREVM (r₁ = 0.4066 and r₂ = 0.2802). The molecular weights ( and ) and the polydispersity index of the copolymers were determined by gel permeation chromatography. The thermal stability of the copolymers increases with increase in concentration of MPDSK. Glass transition temperatures were determined by differential scanning calorimeter under nitrogen atmosphere. The photoreactivity of the copolymers having pendant chalcone moieties was studied in chloroform solution.     

Characterizing changes in levan physicochemical properties in different pH environments using asymmetric flow field-flow fractionation

The purpose of this study was to assess the stability of the polyfructan levan under different pH solution conditions by monitoring changes in the levan physicochemical properties, such as molar mass (M), root mean square radius (r _rms ), hydrodynamic radius (r _h ), structure factor (r _rms /r _h ), and aggregation state with respect to solution pH and hydrolysis time. A commercial levan produced from Z. Mobilis was characterized using asymmetric flow field-flow fractionation (AF4) in combination with online multiangle light scattering (MALS) and differential refractive index (dRI) detection. Under neutral pH solution conditions the levan was found to have a M ranging from 10⁵ to 5?×?10⁷ g/mol, a r _rms ranging from ~25 to 100 nm and a r _h from ~3 to 151 nm. Two populations were observed in the sample. One population with a M less than 10⁶ g/mol which represented ~60 % of the sample and a second population with an ultrahigh M up to 5?×?10⁷ g/mol, which comprised ~40 % of the sample. The measured r _rms /r _h structure factor decreased from 1.8 to 0.65 across the AF4 fractogram indicating that early eluting low M levan species had a random coil configuration and late eluting high M species had more homogeneous spherical structures. The measured apparent density values decreased from 80 to 10 kg/m³ across the elution profile and suggest that the observed second population also contains aggregates. The stability of levan in different pH conditions ranging from 1.3 to 8.5 was assessed by tracking changes in the average M and r _h , and monitoring the formation of fructose over 1 week. The onset of levan acid hydrolysis was observed to occur sooner at lower pH conditions and no hydrolysis was observed for pH 5.5 and higher.     

Characterization of lignin using multi-angle laser light scattering and atomic force microscopy

Small differences in the isolation techniques of lignin can result in significant changes in its molecular structure and configuration. Light scattering (evaluated at 18 different angles in a plane), Atomic Force Microscopy (AFM) and Near Infrared Spectroscopy (NIR) proved very effective for evaluating the characteristics of lignin. Zimm plots were generated using Zimm, Debye and Berry formalisms to evaluate the weight average molecular weight (MW), radius of gyration (r_g), hydrodynamic radius (r_h) and second virial coefficient (A₂). Two types of lignin and nine different solvents were used for the study, to analyze the conformation of lignin molecules in different solvents expected to be used in lignin degradation and subsequent analysis. Absolute MW and r_g decreased and the dn/dc increased when the solvent used for lignin was changed from water to sodium hydroxide. The two types of lignin also exhibited different values for all the above estimated parameters. This study also highlighted the differences between the unlyophilized and lyophilized lignin in terms of aggregation, pH dependence and stability over time. This aggregation has never been seen on a ultraviolet (UV) or refractive index (RI) detector that has been used so far for liquid chromatography (LC) reducing the reliability of lignin depolymerization data obtained without light scattering.     

Magnetic single-component molecular conductors exhibiting strong π-d interactions

Single-component molecular conductors [M(tmdt)₂] (tmdt = trimethylenetetrathiafulvalenedithiolate; M = Ni, Au, Pt, Cu), exhibit a variety of electromagnetic properties, which originate from the differences of the metal’s d-orbitals role in the band structure formation. The [Au(tmdt)₂] crystal undergoes an antiferromagnetic transition at 110 K, while maintaining a metallic state at lower temperatures. The Au analog has a high magnetic transition temperature as compared to traditional magnetic molecular conductors due to the strong three-dimensional (3-D) structure and the contribution of the metal d-orbitals. The single-component molecular conductor, [Cu(tmdt)₂], with π- and d-like frontier orbitals is isostructural with other metallic [M(tmdt)₂] systems (M = Ni, Pt, Au). The Cu(tmdt)₂ molecule is planar, which strikingly contrasts the tetrahedral coordination of Cu(dmdt)₂ (dmdt = dimethyltetrathiafulvalenedithiolate) with similarly extended TTF type ligands. Interestingly, unlike other [M(tmdt)₂] with metallic behavior, [Cu(tmdt)₂] shows semiconducting behavior at room temperature (σ(RT) = ∼7 S cm⁻¹). The RT conductivity increased linearly with increased pressure to 110 S cm⁻¹ at 15 kbar despite the compressed pellet sample. The magnetic susceptibility indicates one-dimensional (1-D) Heisenberg behavior with J = 117 cm⁻¹ and shows antiferromagnetic ordering at 13 K. The [Cu(tmdt)₂] is a new multi-frontier π-d system, which introduces a d(σ)-type frontier orbital around the Fermi level of the π-like metal bands.     

Reversible addition-fragmentation chain transfer radical copolymerization of β-pinene and methyl acrylate

The feasibility of radical copolymerization of β-pinene and methyl acrylate (MA) was clarified for the first time. The monomer reactivity ratios were evaluated by Fineman-Ross, Kelen-Tudos and non-linear methods, respectively. The obtained values were r_β-pinene ∼ 0 and r_MA ∼ 1.3, indicating that the copolymerization led to polymers rich in methyl acrylate units and randomly alternated by single β-pinene unit. The addition of Lewis acid Et₂AlCl to the AIBN-initiated copolymerization enhanced the incorporation of β-pinene. Furthermore, the possible controlled copolymerization of β-pinene and MA was then attempted via the reversible addition-fragmentation transfer (RAFT) technique. The copolymerization (f_β-pinene = 0.1) using 1-methoxycarbonyl ethyl dithiobenzoate (MEDB) as a RAFT agent gave copolymers with lower molecular weight and narrower molecular weight distribution. However, the presence of MEDB strongly retarded the copolymerization. Thus a new RAFT agent 1-methoxycarbonyl ethyl phenyldithioacetate (MEPD), which gives a less stable macroradical intermediate than MEDB, was synthesized and introduced to the copolymerization. As anticipated, a much smaller retardation was observed. Moreover, the copolymerization displayed a somewhat controlled features within a certain overall conversion (<∼40%).     

Thermal degradation of polycarbonate, poly(vinyl acetate) and their blends

We have recently developed a novel approach for intimately mixing thermodynamically incompatible polymers, which utilizes the formation of inclusion compounds (ICs) formed with host cyclodextrins (CDs), followed by removal of CD and coalescence of the common guest polymers into a blend. In this paper direct insertion probe pyrolysis mass spectrometry (DIP-MS) analyses of polycarbonate (PC), poly(vinyl acetate) (PVAc) and PC/PVAc blends, obtained by coalescence from their inclusion compounds formed with host γ-CD (coalesced blend) and by co-precipitation (physical blend), have been performed. Variations in the thermal stabilities of the coalesced polymers were recorded both by TGA and DIP-MS and compared to the corresponding as-received polymers. It has been determined that for both coalesced and physical blends of PC/PVAc, CH₃COOH formed by deacetylation of PVAc above 300 °C, reacts with PC chains decreasing their thermal stability. This process was more effective for the physical blend, most likely due to enhanced diffusion of CH₃COOH, produced by deacetylation of PVAc, into the PC domains, where it can further react producing low molecular weight PC fragments bearing methyl carbonate chain ends.     

Conventional and fast gas chromatography analysis of biodiesel blends using an ionic liquid stationary phase

The present research is focused on the GC-FID determination of fatty acid methyl esters (FAMEs) in diesel blends, by means of an ionic liquid stationary phase, characterized by a dicationic 1,9-di(3-vinyl-imidazolium)nonane bis(trifluoromethyl)sulfonylimidate structure (SLB-IL100). The high polarity of the ionic liquid stationary phase allowed the separation of the FAMEs, from the less-retained hydrocarbons, thus avoiding the requirement of a hydrocarbon LC pre-separation. The results derived from the analyses of a soybean FAMEs B20 sample, carried out on an SLB-IL100 conventional column (30 m × 0.25 mm i.d. × 0.20 mm d_f), were compared with those attained on a polyethylene glycol column, of equivalent dimensions. Conventional and fast GC methods, for the analysis of FAMEs in diesel blends, were developed on an SLB-IL100 30 m × 0.25 mm i.d. × 0.20 μm d_f and on an SLB-IL100 12 m × 0.10 mm i.d. × 0.08 μm d_f column, respectively. The optimized IL methods were subjected to validation: retention time and peak area intra-day precision (n = 5) were good, with CV % values lower than 0.08% and 4.9%, respectively. With regards to the quantitation of FAMEs in biodiesel blends, a five points calibration curve was constructed, using C_17:0 as internal standard.     

Reactivity ratios in conventional and nickel-mediated radical copolymerization of methyl methacrylate and functionalized methacrylate monomers

Copolymerization of an excess of methyl methacrylate (MMA) relative to 2-hydroxyethyl methacrylate (HEMA) was carried out in toluene at 80 °C according to both conventional and controlled Ni-mediated radical polymerizations. Reactivity ratios were derived from the copolymerization kinetics using the Jaacks method for MMA and integrated conversion equation for HEMA (r_MMA = 0.62 ± 0.04; r_HEMA = 2.03 ± 0.74). Poly(ethylene glycol) α-methyl ether, ω-methacrylate (PEGMA, M_n = 475 g mol⁻¹) was substituted for HEMA in the copolymerization experiments and reactivity ratios were also determined (r_MMA = 0.75 ± 0.07; r_PEGMA ∼ 1.33). Both the functionalized comonomers were consumed more rapidly than MMA indicating the preferred formation of heterogeneous bottle-brush copolymer structures with bristles constituted by the hydrophilic (macro)monomers. Reactivity ratios for nickel-mediated living radical polymerization were comparable with those obtained by conventional free radical copolymerization. Interactions between functional monomers and the catalyst (NiBr₂(PPh₃)₂) were observed by ¹H NMR spectroscopy.     

Rapid and simultaneous analysis of dichlorvos, malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid in citrus fruit by flow-injection ion spray ionization tandem mass spectrometry

A simple method for the rapid and simultaneous analysis of dichlorvos (DDVP), malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid (2,4-D) in citrus fruit, which uses flow-injection ion spray ionization tandem mass spectrometry, has been developed for the first time. The method involves the combined use of stable isotopically labeled internal standards (DDVP-d₆, malathion-d₁₀, carbaryl-d₇, and 2,4-D-d₅) and a multiple reaction monitoring technique. The average recoveries for the pesticides at the same concentrations as their tolerance levels (DDVP: 0.1-0.2 μg g⁻¹; malathion: 0.5-4.0 μg g⁻¹; carbaryl: 1.0 μg g⁻¹; 2,4-D: 1.0-2.0 μg g⁻¹) ranged from 90 to 119% with the relative standard deviation (R.S.D.) ranging from 1.0 to 13.1% (n = 5). Analysis time, including sample preparation and determination, was only 15 min. The present method is effective for screening DDVP, malathion, carbaryl, and 2,4-D in citrus fruit.     

Synthesis and properties of phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety

Three novel series of soluble and curable phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety were synthesized from an excess amount of three dianhydrides and phthalazinone-based diamine, followed by reacting with 4-(3-aminophenoxy)phthalonitrile (APPh) in a two-step, one-pot reaction, respectively. The phthalonitrile oligomers containing phthalazinone moiety were cured in the presence of 4,4′-diaminodiphenylsulfone (DDS). The oligomers and the crosslinked polymers were characterized by DSC, FT-IR and elemental analysis. These phthalonitrile oligomers containing phthalazinone groups were found to be soluble in some aprotic solvents, such as chloroform, pyridine, m-cresol and N-methyl-2-pyrrolidone (NMP). The crosslinked polymers were insoluble in all solvents. The thermal properties of the oligomers and the crosslinked polymers were evaluated using DSC and TGA analysis. The phthalonitrile oligomers showed high glass transition temperatures (T_gs) in the range of 214-256 °C and high decomposition temperatures with 10% weight loss (T_d10%) ranging from 523 to 553 °C. The crosslinked polymers showed excellent thermal stability with the 10% weight loss temperatures ranging from 543 to 595 °C, but did not exhibit a glass transition temperature upon heating to 350 °C.     

Novel synthetic approach in microwave-assisted solid-supported oxidations using ‘in situ’ generated molecular oxygen

Three different types of oxidation reactions were carried out under microwave (MW) conditions in dry media, with nearly quantitative yield, using ‘in situ’, yet separately generated molecular oxygen as the reactive gas. The latter is formed by a controlled decomposition of potassium chlorate (220-306 °C) adsorbed on zeolite support, and is used as a reactive oxidizing agent for the solid-supported oxidations. The MW-assisted oxidations include an oxidative decomplexation of (η⁶-arene)Cr(CO)₃ complexes to the corresponding arenes using silica as solid support (100 °C), an oxidation of fluorene to fluorenone induced by KF-alumina support (150 °C), and oxidation of benzyl alcohol to benzaldehyde using a supported ruthenium catalyst (150 °C). This synthetic approach allows to carry out in synchronized manner two different solid-supported reactions (oxygen generation and oxidation) at different temperatures and on different solid supports together in the same sealed system. It was made possible by tuning the absorption efficiency of MWs through accurate selection of the solid supports employed in the reactions. The high feasibility of this novel synthetic approach resulted from a preliminary study of the interaction between MWs and mineral oxides such as alumina, silica, clay, and zeolite particularly when mixed with additives such as water, ionic liquids or graphite (5% w/w). The use of these MW absorber additives allows the MW transparent or poorly absorbing mineral oxides to be efficiently heated to very high temperatures in few minutes.     

Electronic transition moment of the AΠr-XΣ system of TiN

The A²Π_r-X²Σ⁺ transition of TiN was observed by the dispersed laser induced fluorescence (DLIF) spectroscopy. The relative intensities of the DLIF spectra were analyzed to determine the dependence of the electronic transition moment, R_e(r), on the internuclear distance, r, as R_e(r)∝{1−0.281(26)r} (1.380 Å≤r≤1.823 Å). This r-dependence was analyzed simultaneously with the reported values of the spin-orbit constants for A²Π_r and the hyperfine-coupling constants for X²Σ⁺ to evaluate the ionic character of the TiN bond, the 4s atomic character in the 9σ orbital of X²Σ⁺, and the 4p atomic character in the 4π orbital of A²Π_r. These characters were confirmed to be in accordance with the reported theoretical prediction. A strong r-dependence was indicated for the 3d-4p mixing in the A²Π_r state due to the configuration mixing of the Ti(3d⁴) and Ti(3d³4p) states at a large internuclear distance.     

Radical copolymerization of vinylidene fluoride with perfluoroalkylvinyl ethers

The radical copolymerization of perfluoromethylvinyl ether (PMVE) and perfluoropropylvinyl ether (PPVE) with vinylidene fluoride (VDF), initiated by tertiobutyl peroxypivalate (TBPPI) and ditertiobutyl peroxide (DTBP), respectively, are presented. The kinetics of copolymerization were investigated for each monomer from series of at least eight reactions for which the initial [VDF]₀/[fluorinated vinyl ether]₀ molar ratios ranged between 20/80 and 80/20. The copolymer compositions of these random-type copolymers were calculated by means of ¹⁹F NMR spectroscopy and allowed one to quantify the respective amounts of each monomeric unit in the copolymer. According to the Tidwell and Mortimer method, the reactivity ratios (r_i) of both comonomers for each type of copolymerization were obtained : r_VDF = 3.40 ± 0.40 and r_PMVE = 0 at 74 °C; and r_VDF = 1.15 ± 0.36 and r_PPVE = 0 at 120 °C. Moreover, the glass transition temperatures (T_g’s) of poly(VDF-co-PMVE) and poly(VDF-co-PPVE) copolymers containing different amounts of VDF and PMVE or PPVE, were determined and the theoretical glass transition temperatures of poly(PMVE) and poly(PPVE) homopolymer were deduced.     

Quantification of 2-acetyl-1-pyrroline in rice by stable isotope dilution assay through headspace solid-phase microextraction coupled to gas chromatography-tandem mass spectrometry

A new and convenient synthesis of 2-acetyl-1-pyrroline (2AP), a potent flavor compound in rice, and its ring-deuterated analog, 2-acetyl-1-d₂-pyrroline (2AP-d₂), was reported. A stable isotope dilution assay (SIDA), involving headspace solid-phase microextraction (HS-SPME) combined with gas chromatography-positive chemical ionization-ion trap-tandem mass spectrometry (GC-PCI-IT-MS-MS), was developed for 2AP quantification. A divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fiber was used for HS-SPME procedure and parameters affecting analytes recovery, such as extraction time and temperature, pH and salt, were studied. The repeatability of the method (n = 10) expressed as relative standard deviation (RSD) was 11.6%. A good linearity was observed from 5.9 to 779 ng of 2AP (r² = 0.9989). Limits of detection (LOD) and quantification (LOQ) for 2AP were 0.1 and 0.4 ng g⁻¹ of rice, respectively. The recovery of spiked 2AP from rice matrix was almost complete. The developed method was applied to the quantification of 2AP in aerial parts and grains of scented and non-scented rice cultivars.     

Composition and molecular weight analysis of styrene-acrylic copolymers using thermal field-flow fractionation

Thermal field-flow fractionation coupled with online multiangle light scattering, differential refractive index and quasielastic light scattering (ThFFF-MALS/dRI/QELS) was used to simultaneously determine the molecular weight (MW) and composition of polystyrene-poly(n-butyl acrylate) (PS-PBA) and polystyrene-poly(methyl acrylate) (PS-PMA) copolymers. The online measurement of the normal diffusion coefficient (D) by QELS allowed calculation of the copolymer thermal diffusion coefficient (D(T)) of sample components as they eluted from the ThFFF channel. DT was found to be independent of MW for copolymers with similar compositions and dependent on composition for copolymers with similar MW in a non-selective solvent. By using a solvent that is non-selective to both blocks of the copolymer, it was possible to establish a universal calibration plot of DT versus mole fraction of one of the monomer chemistries comprising the copolymer. PS-PBA and PS-PMA linear diblock polymers were determined to vary in composition from 100/0 to 20/80 wt% PS/acrylate and ranged in MWs between 30 and 360 kDa. The analysis of a PS-PBA miktoarm star copolymer revealed a polydisperse material with a weight percent PBA of 50-75% and MW ranging from 100 to 900 kDa. The presented ThFFF-MALS/dRI/QELS method allowed rapid characterization of polymers with MW and chemical distributions in a single analysis.     

Studying the distribution pattern of selenium in nut proteins with information obtained from SEC-UV-ICP-MS and CE-ICP-MS

In this work, size exclusion chromatography (SEC) with UV and inductively coupled plasma mass spectrometry (ICP-MS) detection was used to study the association of selenium to proteins present in Brazil nuts (Bertholletia excelsa) under five different extraction conditions. As expected, better solubilization of proteins was observed using 0.05 mol L⁻¹ sodium hydroxide and 1% sodium dodecylsulfate (SDS) in Tris/HCl buffer (0.05 mol L⁻¹, pH 8) as compared to 0.05 mol L⁻¹ HCl, 0.05 mol L⁻¹ Tris/HCl or hot water (60 °C). Due to non-destructive character of Tris-SDS treatment, this was applied for studying molecular weight (MW) distribution patterns of selenium-containing nut proteins. Three different SEC columns were used for obtaining complete MW distribution of selenium: Superdex 75, Superdex Peptide, and Superdex 200 were tested with 50 mmol L⁻¹ Tris buffer (pH 8), 150 mmol L⁻¹ ammonium bicarbonate buffer (pH 7.8), phosphate (pH 7.5), and CAPS (pH 10.0) mobile phases. Using Superdex 200 column, the elution of at least three MW fractions was observed with UV detection (200-10 kDa) and ICP-MS chromatogram showed the co-elution of selenium with the two earlier fractions. The apparent MWs of these selenium-containing fractions were respectively about 107 and 50 kDa, as evaluated from the column calibration. For further characterization of individual selenium species, the defatted nuts were hydrolyzed with proteinase K and analyzed by capillary electrophoresis (CE) with ICP-MS detection. The suitability of CE for the separation of selenite, selenate, selenocystine and selenomethionine in the presence of the nut sample matrix is demonstrated. Complete separation of the above mentioned selenium species was obtained within a migration time of 7 min. In the analysis of nut extracts with CE-ICP-MS, selenium was found to be present mainly as selenomethionine.     

Dechlorination of poly(vinyl chloride) by microwave irradiation I: A simple examination using a commercial microwave oven

Poly(vinyl chloride) (PVC) was decomposed by microwave (MW) irradiation (2.45 GHz) using a commercial MW oven. The efficiency of dielectric absorption was evaluated quantitatively from the rate of temperature increase on MW irradiation. The efficiency of dielectric heating increased at temperatures above the glass transition temperature (T_g). The decomposition on MW irradiation, monitored using the weight, depended on the initial (preheating) temperature of the sample before irradiation. The degradation time profile with various initial temperatures was shifted along the time axis and was successfully superimposed on a single curve. A pure PVC film was subjected to heating at a constant temperature from 230 °C to 310 °C, and the rate of weight decrease on heating was measured. The apparent activation energy was 84.4 kJ/mol for a single monomer unit.