Effect of heat treatment of the D16 alloy on its mechanical properties at low stresses

The elastic hysteresis and residual deflection of the aluminum D16 alloy samples corresponding to the model of a circular plate clamped along its perimeter have been studied at low (the beginning of the Hooke region) mechanical stresses. It has been shown that these characteristics depend substantially (change several times) on the sample state provided by different heat treatment conditions. The non-destructive method used in this work has a high accuracy and can be used to estimate the strength, yield stress, and fatigue life of metals.     

Effect of laser shot peening on precipitation hardened aluminum alloy 6061-T6 using low energy laser

Mechanical properties of engineering material can be improved by introducing compressive residual stress on the material surface and refinement of their microstructure. Variety of mechanical process such as shot peening, water jet peening, ultrasonic peening, laser shot peening were developed in the last decades on this contrast. Among these, lasers shot peening emerged as a novel industrial treatment to improve the crack resistance of turbine blades and the stress corrosion cracking (SCC) of austenic stainless steel in power plants. In this study we successfully performed laser shot peening on precipitation hardened aluminum alloy 6061-T6 with low energy (300 mJ, 1064 nm) Nd:YAG laser using different pulse densities of 22 pulses/mm² and 32 pulses/mm². Residual stress evaluation based on X-ray diffraction sin² ψ method indicates a maximum of 190% percentage increase on surface compressive stress. Depth profile of micro-hardness shows the impact of laser generated shock wave up to 1.2 mm from the surface. Apart from that, the crystalline size and micro-strain on the laser shot peened surfaces have been investigated and compared with the unpeened surface using X-ray diffraction in conjunction with line broadening analysis through the Williamson-Hall plot.     

New crystalline phases of an equiatomic K-Cs alloy at low temperature

Solid equiatomic K-Cs alloys have been investigated by X-ray diffraction throughout the temperature range 300-100K. The results indicate that a phase separation occurs below 185K accompanied by the appearance of an ordered phase in this range. This phase has a hexagonal lattice with parameters: a = 9.32(1) Å and c = 11.80(2) Å (at 170K). Evidence from our other studies [7] indicates that its composition is K₂Cs. Another phase transformation in this ordered crystal is observed below 120K. There is no change of lattice symmetry but the unit cell constants shrink to the values: a = 9.11(1) Å and c = 10.86(2) Å (at 100K). The transformation can be ascribed to a rearrangement of the electronic structure of Cs.     

Perspectives for low energy antiproton physics at FAIR

The CRYRING accelerator, previously located at the Manne Siegbahn Laboratory of Stockholm University, has been chosen by the FLAIR collaboration as the central accelerator for the planned facility. It has been modified to allow for high-energy injection and extraction and is capable of providing fast and slow extracted beams of antiprotons and highly charged ions. It is currently being installed at the ESR of GSI Darmstadt where it can be used with highly charged ions. The future possibilities for its use with slow antiprotons will be discussed.     

Bag-model quantum chromodynamics for hyperons at low energy

In a non-perturbative bag model framework, gluon exchange which mediates quark exchange scattering in conjunction with quark interchange is shown to be the basis of the OBE interactions of hyperons at low energy.     

Nanoporosity of fine-crystalline aluminum and an aluminum-based alloy

The presence of nanopores formed during the equal-channel angular pressing of aluminum is revealed using small-angle x-ray scattering. The parameters of nanopores are determined, and a correlation between the level of nanoporosity and the fraction of high-angle grain boundaries is found. The data obtained indicate that the level of nanoporosity can affect the tensile durability of fine-crystalline aluminum in the creep mode. The data on the regularities in the development of nanopores under deformation of the fine-crystalline aluminum-based alloy in the superplasticity mode are obtained.     

Non-Newtonian deformation of Co-based metallic glass at low stresses

The results of precision measurements of creep in Co-based metallic glass are presented. It is shown that, in spite of generally accepted concepts, plastic flow at low stresses under intense structural relaxation conditions is of a non-Newtonian type. Consequences of this fact are considered.     

Surface diffusion: the low activation energy path for nanotube growth

We present the temperature dependence of the growth rate of carbon nanofibers by plasma-enhanced chemical vapor deposition with Ni, Co, and Fe catalysts. We extrapolate a common low activation energy of 0.23-0.4 eV, much lower than for thermal deposition. The carbon diffusion on the catalyst surface and the stability of the precursor molecules, C2H2 or CH4, are investigated by ab initio plane wave density functional calculations. We find a low activation energy of 0.4 eV for carbon surface diffusion on Ni and Co (111) planes, much lower than for bulk diffusion. The energy barrier for C2H2 and CH4 dissociation is at least 1.3 eV and 0.9 eV, respectively, on Ni(111) planes or step edges. Hence, the rate-limiting step for plasma-enhanced growth is carbon diffusion on the catalyst surface, while an extra barrier is present for thermal growth due to gas decomposition.     

Free energy of segregation at alloy surfaces

The free energy of segregation at semi-infinite solid binary alloy surfaces is calculated using a quasi-chemical approach. The alloy is treated to be a non-regular solution. The concentration is assumed to be different only at the surface layer. The theory is applied to AgAu alloys. The concentration and the short-range-order parameters at the surface are calculated.     

铝纳米晶的低温导电特性研究

采用真空热压技术将电磁感应加热-自悬浮定向流法制备的铝纳米粉末压制成块体样品.通过X射线衍射、透射电子显微镜、扫描电子显微镜及X射线能谱分析了铝纳米晶的微观结构,并用四探针法测量了不同温度下(8—300 K)样品的电阻率,研究了铝纳米晶的电阻率(ρ)随温度的变化规律.结果表明:由于晶界(非晶氧化铝)对电子的散射以及晶界声子对电子的散射效应,低温(40 K)下,铝纳米晶的本征电阻率随温度变化关系明显不同于粗晶铝,不仅呈现出T~4变化,还表现出显著的T3变化规律.因晶界等缺陷和非晶氧化铝杂质对电子的散射,铝纳米晶残余电阻率比粗晶铝电阻率大5—6个数量级.     

Effect of alkaline cleaning and activation on aluminum alloy 7075-T6

The effect of alkaline cleaning and activation on the composition and thickness of the oxide layer on aluminum alloy 7075-T6 was studied. E-pH diagrams were developed to predict the effect of alkaline cleaning and activation solutions on the stability of the oxide surface layers. The thickness of the native oxide layer was determined to be ∼30 nm by Auger electron spectroscopy depth profiling analysis. The outer ∼20 nm was rich in magnesium while the remaining ∼10 nm was rich in aluminum. Cleaning in a 9.1 pH alkaline solution was found to remove the magnesium-rich layer and leave behind an aluminum-rich oxide layer ∼10 nm thick. Activation in alkaline solutions of NaOH (pH > 12.9) or Na₂CO₃ (pH > 11.5) produced an oxide that was ∼20 to 60 nm thick and rich in magnesium. Alkaline cleaning and activation altered the oxide composition and thickness making it possible for deposition of thicker cerium-based conversion coatings (∼100 to 250 nm) compared to only alkaline cleaning (∼30 nm), with application of one spray cycle of deposition solution.     

非晶合金中的低温电阻率极小行为研究

研究了非磁非晶合金Cu₆₀Zr₂₀Hf₁₀Ti₁₀和铁磁非晶合金Fe₆₁Co₇Zr₁₀Mo₅W₂B₁₅的低温电阻，用不同的模型对电阻温度曲线进行拟合.对两个样品中出现的极小值行为进行分析，探讨了无序结构和磁性状态对极小值行为的影响. 关键词： 非晶合金 电阻 极小值     

铝合金材料在14 MeV中子

铝合金是激光惯性约束聚变(ICF)装置中最常用的结构材料之一,将直接受到高能量、高产额的中子辐照。评估铝合金材料在14 MeV中子辐照下的活化特性,可为我国ICF装置的材料选取提供参考。采用FISPACT活化计算软件,计算并比较了三种不同牌号的铝合金材料在14 MeV中子辐照后产生的比活度和剂量率,并分析了不同元素对比活度和剂量率的贡献。结果表明,铝合金的比活度和剂量率在冷却一周之内下降了3个数量级。铝合金的活化主要来自Al元素、Mn元素和Zn元素,主要活化产物为²⁴Na, ⁵⁴Mn和⁶⁵Zn。Al元素在冷却一周内对比活度(剂量率)的贡献大于90%,其余两种元素在两周之后占主导作用,其贡献之和超过50%。通过选取低Mn, Zn质量分数的铝合金,可降低材料在活化后的放射性水平。     

Photoproduction of pions at low energy

Presented in this paper is a field theory model for photoproduction of pions at low energy. In particular, it is shown that certain interaction terms, which were previously considered to be essential in order to explain the experimental situation corresponding to the spin-3/2 resonances, are really unnecessary and that the presence of these terms are not justifiable from the theoretical point of view. Further, the free parameters in the theory representing the off-mass-shell effects of the spin-3/2 particles are fixed on the basis of theoretical considerations.     

Bag-model quantum chromodynamics at low energy

Gluon-exchange mediating quark-exchange scattering is the mechanism of lowest order in perturbative QCD that contributes to the strong interactions at low energy. When it is dressed with long-range quark-gluon correlations by means of bag-model wavefunctions, this quark interchange force becomes bilocal in the quark-gluon sector involving the whole bag and non-perturbative. When it is Fierz-rearranged, the quark-interchange amplitude takes on the usual local form for each hadron that is expected from the wealth of empirical knowledge at low energy. This quark interchange is calculated here in the MIT bag model, which is supplemented by tunneling rules, and then applied to elastic NN scattering, and subsequently toπN andππ scattering. For each reaction the OBE interaction is obtained in agreement with meson theoretic models. Repulsive axial-vector meson exchanges are predicted for NN scattering at short range. The chiral structure of the quark interchange force in conjunction with its tunneling aspects suggest an interpretation of the strong interactions at low energy as Josephson currents of non-Abelian superconductivity.     

激光超声检测铝合金材料的残余应力分布

为了有效检测铝合金材料上的残余应力分布,研究了用激光超声技术来检测铝合金材料上的残余应力分布的方法。该方法用Nd:YAG脉冲激光激发声表面波,并用外差激光干涉仪接收。理论分析表明可通过测量表面波在不同位置上声速的相对变化,来确定试样的残余应力分布。并对无残余应力、有压缩残余应力、有拉伸残余应力的三个试样应力分布,进行了实验测定。结果证实了试样的残余应力分布可引发声表面波在不同位置上声速的相对变化,也证实了激光激发声表面波及其接收技术是一种无损检测材料内残余应力分布的有效方法。     

Braneworld cosmological perturbation theory at low energy

Homogeneous cosmology in the braneworld can be studied without solving bulk equations of motion explicitly. The reason is simply because the symmetry of the spacetime restricts possible corrections in the 4-dimensional effective equations of motion. It would be great if we could analyze cosmological perturbations without solving the bulk. For this purpose, we combine the geometrical approach and the low energy gradient expansion method to derive the 4-dimensional effective action. Given our effective action, the standard procedure to obtain the cosmological perturbation theory can be utilized and the temperature anisotropy of the cosmic background radiation can be computed without solving the bulk equations of motion explicitly.     

Simulation of low energy displacement processes in a dilute cu-au alloy

Abstract

Research into displacement cascade processes in alloy systems has received little attention, yet is potentially of interest because issues such as the effect of solutes on the displacement threshold and the defect distribution and movement in cascades are important. As part of a wider study, we have initially considered the minor substitutional solute Au in a Cu matrix, and have used molecular dynamics to investigate the properties of point defects, the threshold displacement energy E_d, and temporal and spatial distribution of defects in low-energy (≤500 eV) displacement cascades. The results show that the influence of the solute on the properties of defects is important and that E_d is dramatically different from its form in pure copper. In comparison with pure copper, the recoil of the Au solute gives rise to a higher peak at longer times in the number of displaced atoms in the generation of a displacement cascade. The influence of this on defect density in the cascade and the final number and arrangement of defects has been investigated.